Nexus 4 unresponsive screen... - Nexus 4 Q&A, Help & Troubleshooting

Hi,
I have a Nexus 4 16GB here and a Nexus 4 8 GB and my 16GB one isn't working, the screen turns on and it boots fine but the screen is completely unresponsive to touch...
I have tried swapping the logic boards over and the 16GB one doesn't work in the other phone either, which rules out the screen/digitizer but points towards the logic board...
I can't even click on anything in TWRP... Anyone got any ideas or advice?

Bump, could really do with some help on this...

Sounds like display driver on the logic board is done.

br0ok1ynb0i said:
Sounds like display driver on the logic board is done.
Click to expand...
Click to collapse
So can't be fixed?

Hyflex said:
So can't be fixed?
Click to expand...
Click to collapse
I don't know, but when it happened to my other phone, replacing the logic board was the route I took.

BUmp

I'm afraid nothing can be done on that borked mobo. At least the digitiser is fine!

Shame it's a knockoff digitizer, it was a phone purchased as "brand new" which it clearly wasn't, from eBay.
Lasted a matter of a day before giving up...
I got a full refund after enough hastle so now I'm left with this bit of junk I my room.
Got a spare battery and front/back if I damage my legit 8gb one.
Should I remove the battery from the poop phone? (Does that stop them from becoming dead?)

Bump

I am also suffering from same problem, but in my phone 1/5 Lower part of screen is not receiving any touch, i want to ask something that shall i need to change the digitizer only or digitizer+screen
Sent from my Nexus 4 using XDA Free mobile app

Related

[Q] just purchased a g2 for $30. screen doesnt turn on

The phone definitely boots up because the lights on the buttons flash on then turn off after some time. The keyboard also lights up. You can tell the backlight turns on on the screen, but there is no picture.
Anyone have any idea about what I should do? Thinking about trying to restore to a stock Tom somehow tonight. Then I'm thinking about looking for screen replacements.
I was curious if anyone has had this issue before.
Update 07/14/11
So I got the screen and switched the old one out for the new one. This one also only has the backlight turning on, but I noticed when I put a part back on, there was a little bump in the middle of the phone. Haven't had a chance to fix it, but I noticed it's a piece hitting this rubber piece that seems to "transport" the sound for the mic from the bottom of the phone to the actual microphone module within the phone.
Removed that rubber piece, and I'll try installing it later. I was getting some blue and red visible in the middle of the phone. Anyone know what's wrong?
albanianbrotha said:
The phone definitely boots up because the lights on the buttons flash on then turn off after some time. The keyboard also lights up. You can tell the backlight turns on on the screen, but there is no picture.
Anyone have any idea about what I should do? Thinking about trying to restore to a stock Tom somehow tonight. Then I'm thinking about looking for screen replacements.
I was curious if anyone has had this issue before.
Click to expand...
Click to collapse
ebay for the parts and look around for the link for repairs. I don't exactly remember the link, but it's in one of the "spring replacement" threads. Good luck
mputtr said:
ebay for the parts and look around for the link for repairs. I don't exactly remember the link, but it's in one of the "spring replacement" threads. Good luck
Click to expand...
Click to collapse
How sure are you it's the LCD screen? Replacement screens cost more than what I bought the phone for...lol
it's mostly the physical connection to the screen.
and on your note about it costing more than what you bought the phone for... there are tons of parts on the phone that will cost more than 30bucks. not much you can do about that since you got it non fully functional.
mputtr said:
it's mostly the physical connection to the screen.
and on your note about it costing more than what you bought the phone for... there are tons of parts on the phone that will cost more than 30bucks. not much you can do about that since you got it non fully functional.
Click to expand...
Click to collapse
Sorry to be a both, but what exactly is the physical connection? Do I find it by opening the phone up completely to the point where I replace the actual LCD?
albanianbrotha said:
Sorry to be a both, but what exactly is the physical connection? Do I find it by opening the phone up completely to the point where I replace the actual LCD?
Click to expand...
Click to collapse
Never had to do it myself, but there is a cable connecting the two parts of the phone. That is usually where this problem originates from. It's not easy to fix though if your not familiar with fixing electronics from what i have seen.
xsteven77x said:
Never had to do it myself, but there is a cable connecting the two parts of the phone. That is usually where this problem originates from. It's not easy to fix though if your not familiar with fixing electronics from what i have seen.
Click to expand...
Click to collapse
I've taken apart my laptop completely and put it back together before. Completely as in taking the lcd off and different chips and wireless modules and stuff. I think it may be something I can handle. I'm going to take a look at it now. Restoring wont do me any good because not even the boot screen shows up.
albanianbrotha said:
Sorry to be a both, but what exactly is the physical connection? Do I find it by opening the phone up completely to the point where I replace the actual LCD?
Click to expand...
Click to collapse
It's pretty much a ribbon cable that feeds data to display and stuff. When you buy a spare screen, it usually comes with a connector
Sent from my Desire Z via XDA App
mputtr said:
It's pretty much a ribbon cable that feeds data to display and stuff. When you buy a spare screen, it usually comes with a connector
Sent from my Desire Z via XDA App
Click to expand...
Click to collapse
So I completely tore apart the phone, got to the point where if I had another LCD screen, I could have easily switched it out. But I don't, so I just put it all back together. I really hope this new LCD will fix the issue. I really hope it's not some other motherboard issue. If all else fails, it goes up on eBay for $70-$100 as is for the phone. If I fix it, I just got myself a phone that goes for $200 used for only $57.
sure. goodluck with it. if you can do it then you're all set. good luck
albanianbrotha said:
So I completely tore apart the phone, got to the point where if I had another LCD screen, I could have easily switched it out. But I don't, so I just put it all back together. I really hope this new LCD will fix the issue. I really hope it's not some other motherboard issue. If all else fails, it goes up on eBay for $70-$100 as is for the phone. If I fix it, I just got myself a phone that goes for $200 used for only $57.
Click to expand...
Click to collapse
Only $57? That would make the lcd screen $27 if u really paid $30 for the phone, but you said the screen was more than what u paid for the phone...so now im confused.
Sent from my HTC Vision using XDA Premium App
Got my fingers crossed for ya that your getting ur phone fixed over there
Sent from my HTC Vision using XDA Premium App
ptesmoke said:
Only $57? That would make the lcd screen $27 if u really paid $30 for the phone, but you said the screen was more than what u paid for the phone...so now im confused.
Sent from my HTC Vision using XDA Premium App
Click to expand...
Click to collapse
Sorry. After some searching on eBay, I found some sellers selling it for a few dollars less than 30, e.g. 27.
But I decided to go with a seller who sold more than 200, who claims the screen is an OEM screen, and who is top rated. He sells his for $32. Which makes my phone $62 after all is said and done.
The housing has some scratches on the top and bottom though, which decreases the value a bit, but hey, if it works I'll probably keep it as a backup. Currently have the HD2, but I got a Vibrant with original box and accessories for $100, so I think I'm going to sell the HD2.
That was kinda off topic, sorry
LCD screen should be here by the 13th.
Updated OP
someone help =|
I don't own a G2 but I still think this could be a similar issue to what we get over here on the HTC Droid Incredible. First, what makes you believe its still a screen issue if it lit but just didn't throw picture? Usually thats the symptom of having the wrong recovery version for the device hardware version. Normally for us what happens is we will get somebody who is new and rooting for the first time and they'll end up flashing the wrong recovery or freak out because they don't realize the root process takes a little while and yank the cord. End result being exactly what you've explained above. Phone starts but no screen. So we end up having them do the ruu or a second option which we call a "blind install" where you drop whatever your p file(ours is PB31IMG.zip) so whatever it is for the G2 drop that on the SD and reboot to hboot and do the update process by simply knowing how long to wait between key presses and what keys to hit without useing the screen. Its a unique process and all very magical. Haven't lost a single Inc yet because of this issue.
Anyways bud just a thought...
wildstang83 said:
I don't own a G2 but I still think this could be a similar issue to what we get over here on the HTC Droid Incredible. First, what makes you believe its still a screen issue if it lit but just didn't throw picture? Usually thats the symptom of having the wrong recovery version for the device hardware version. Normally for us what happens is we will get somebody who is new and rooting for the first time and they'll end up flashing the wrong recovery or freak out because they don't realize the root process takes a little while and yank the cord. End result being exactly what you've explained above. Phone starts but no screen. So we end up having them do the ruu or a second option which we call a "blind install" where you drop whatever your p file(ours is PB31IMG.zip) so whatever it is for the G2 drop that on the SD and reboot to hboot and do the update process by simply knowing how long to wait between key presses and what keys to hit without useing the screen. Its a unique process and all very magical. Haven't lost a single Inc yet because of this issue.
Anyways bud just a thought...
Click to expand...
Click to collapse
It doesn't seem to be a ROM issue.
Update 7/18: Sold the G2 on eBay and still made a good lump of money. I was very happy, until another G2 popped up with the same exact issue. Got it for a steal as well, and I tried the OEM screen I got from eBay, and it was still having issues, and it seems to cause the phone to overheat while charging. Definitely a defective screen and someones getting a great deal on a decent condition G2 because I already took the payment after I figured it was the screen I got.
I'm going to try to get a replacement from the guy that sold it to me on eBay, but I already left him positive feedback thinking it was the phone's fault.
Will update probably late July or early August when all of this gets sorted out.
TL;DR: bought 2nd g2 with same issue, turns out replacement screen didn't work in the 2nd g2, too late to not sell the first g2, getting another replacement screen to fix 2nd g2. First g2 was in better condition though =|
SWEEEEEEEEEEEEEEEEEEEEEEEEEEEET
Just installed the second screen that I ordered, and it works PERFECTLY. Phone is perfect nowwww yay. I can't use it right now though, previous owned put a lock pattern on the phone...
Wipe the system and the data and start over.
Sent from my HTC Vision using XDA Premium App
Gratz now a factory wipe and root with a new rom will make it run sweet.
Sent from my Desire Z via XDA App

Touchscreen dead strip!

I've noticed just today that there's a dead strip on the touch screen. It didn't do this yesterday. The Nexus 4 was dropped once from 2 feet high, but that was almost a month ago and everything worked fine until now.
The screen still looks beautiful, no dead pixels, no cracks, and the phone is in a protective case with a screen protector.
It seems to me that the digitiser crapped out, but I'm not sure why it happened so randomly.
A funny thing though is that when I drag something fast across the strip it works. And sometimes it'll recognise a touch as a long touch or two-fingered touch along the strip. Weird.
I attached a few touch test photos to show the issue.
Hopefully there's a fix. Has anyone else had this problem? And if you had to send it back to Google, was something like this covered under warranty? What should I do?
Sent from my Nexus 4 using xda app-developers app
You can try to replace the screen yourself or tell LG/Google to send a replacement via RMA. They have parts floating around Ebay
How risky/costly is it to replace it myself? And does anyone know if it's covered under warranty? Cause if is, it'll be cheaper just to get a replacement from Google.
Are there other ways to check if it is indeed the digitiser? I've seen that sometimes touch screen problems are software related. And if that's the case, it'll be easy to fix.
Sent from my Nexus 4 using xda app-developers app
And .... Out of curiosity, what does cause a digitiser to fail without the screen actually breaking?
Sent from my Nexus 4 using xda app-developers app
dwong93 said:
How risky/costly is it to replace it myself?
Click to expand...
Click to collapse
Depends. If you follow the instruction properly, it works well. If you screw up, then Google/LG wont be able to help. A lot of people have done it and succeeded. There are great articles on the web. The price of a digitizer would be about $50-70. I MAY BE WRONG WITH THE PRICING.
And does anyone know if it's covered under warranty? Cause if is, it'll be cheaper just to get a replacement from Google.
Click to expand...
Click to collapse
In most cases no. Because it worked well and suddenly stopped working. Thus Google would say that its your fault. If you are somehow able to convince the Reps that it wasn't your fault, then there is some hope. I
Are there other ways to check if it is indeed the digitiser? I've seen that sometimes touch screen problems are software related. And if that's the case, it'll be easy to fix.
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
One way is to remove it and put it to a tester or another motherboard and see if it works. But that takes a lot of time and money,
dwong93 said:
And .... Out of curiosity, what does cause a digitiser to fail without the screen actually breaking?
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
Anything. The phone might have overheaten to the point that it flashed a certain section of a digitizer. It may also be a battery problem that escalated. If you feel that it's software problem, flash a ROM a see if it works.
IMHO You should send it to LG and get it fixed for about $140~.
This problem should be covered under warranty. If you honestly haven't done anything to cause this damage. (I'm also clueless as to what a user could do themselves to make just one section of the digitizer stop working)
Then lasting 5 months or less would not be considered reasonable and you should be entitled to a replacement.
Remember it is down to the retailer to prove that you caused any damage.
And if you honestly did nothing and it just crapped out on you then you should have nothing to fear in sending it back for a warranty replacement
Sent from my Nexus 4 using xda app-developers app
That happen to my iphone when it got water damage. But if you did not do anything wrong, it should be covered by warranty.
Ditto
dwong93 said:
I've noticed just today that there's a dead strip on the touch screen. It didn't do this yesterday. The Nexus 4 was dropped once from 2 feet high, but that was almost a month ago and everything worked fine until now.
The screen still looks beautiful, no dead pixels, no cracks, and the phone is in a protective case with a screen protector.
It seems to me that the digitiser crapped out, but I'm not sure why it happened so randomly.
A funny thing though is that when I drag something fast across the strip it works. And sometimes it'll recognise a touch as a long touch or two-fingered touch along the strip. Weird.
I attached a few touch test photos to show the issue.
Hopefully there's a fix. Has anyone else had this problem? And if you had to send it back to Google, was something like this covered under warranty? What should I do?
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
EXACT SAME PROBLEM EXACT SAME LOCATION...
i think there is more to this than just user error .. i too did nothing to cause this .. 1 day it was fine and then next morning .. just stopped working 
 @dwong... did you find a solution to this .. did u try claiming warranty.. this should be covered as there is no physical damage .. please do reply to let me know
any1 else have any idea ??!?
thanks
jeetash said:
EXACT SAME PROBLEM EXACT SAME LOCATION...
i think there is more to this than just user error .. i too did nothing to cause this .. 1 day it was fine and then next morning .. just stopped working
@dwong... did you find a solution to this .. did u try claiming warranty.. this should be covered as there is no physical damage .. please do reply to let me know
any1 else have any idea ??!?
thanks
Click to expand...
Click to collapse
I did an RMA explaining everything like I said above. I got my Nexus 4 replaced by Google, and they didn't charge me anything. New Nexus 4 works fine with no issues - I've been using it since May.
dwong93 said:
I did an RMA explaining everything like I said above. I got my Nexus 4 replaced by Google, and they didn't charge me anything. New Nexus 4 works fine with no issues - I've been using it since May.
Click to expand...
Click to collapse
same problem here...did they send you a new phone, or a refurb?
Did you ever find a solution for this?
The same thing has recently happened to mine, did you ever find a solution?
dwong93 said:
I've noticed just today that there's a dead strip on the touch screen. It didn't do this yesterday. The Nexus 4 was dropped once from 2 feet high, but that was almost a month ago and everything worked fine until now.
The screen still looks beautiful, no dead pixels, no cracks, and the phone is in a protective case with a screen protector.
It seems to me that the digitiser crapped out, but I'm not sure why it happened so randomly.
A funny thing though is that when I drag something fast across the strip it works. And sometimes it'll recognise a touch as a long touch or two-fingered touch along the strip. Weird.
I attached a few touch test photos to show the issue.
Hopefully there's a fix. Has anyone else had this problem? And if you had to send it back to Google, was something like this covered under warranty? What should I do?
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
Same bug here in Italy where I'm living now even if the the phone was bought last year on UK Play store. Problem is Google rep wrote me RMA can take place only in UK or any other county where N4 was originally available on Play store i.e. NOT Italy.
Does anybody know of a workaround to get the RMA here?
Thanks
VSSVPM
I have the same problem
Did you ever find a solution to this?
anawim said:
Same bug here in Italy where I'm living now even if the the phone was bought last year on UK Play store. Problem is Google rep wrote me RMA can take place only in UK or any other county where N4 was originally available on Play store i.e. NOT Italy.
Does anybody know of a workaround to get the RMA here?
Thanks
VSSVPM
Click to expand...
Click to collapse
ak700 said:
Depends. If you follow the instruction properly, it works well. If you screw up, then Google/LG wont be able to help. A lot of people have done it and succeeded. There are great articles on the web. The price of a digitizer would be about $50-70. I MAY BE WRONG WITH THE PRICING.
In most cases no. Because it worked well and suddenly stopped working. Thus Google would say that its your fault. If you are somehow able to convince the Reps that it wasn't your fault, then there is some hope. I
One way is to remove it and put it to a tester or another motherboard and see if it works. But that takes a lot of time and money,
Anything. The phone might have overheaten to the point that it flashed a certain section of a digitizer. It may also be a battery problem that escalated. If you feel that it's software problem, flash a ROM a see if it works.
IMHO You should send it to LG and get it fixed for about $140~.
Click to expand...
Click to collapse
Yeah, I think the overheating might have been what happened to mine. I was using a blackberry charger and I think it might have overheated my battery and fried a strip of my digitizer.
Even i have got the same problem, i dont know who bumped this old thread, but please guide me to for a low cost workaround for my situation
No drop or glass break.. Dead pixel just one..
Hi,
Anybody found the reason for the issue, i too got the same issue; a dead strip exactly in the middle of the screen, My warranty is over already, so anyone has work around for this??
sid21 said:
Even i have got the same problem, i dont know who bumped this old thread, but please guide me to for a low cost workaround for my situation
No drop or glass break.. Dead pixel just one..
Click to expand...
Click to collapse
This looks like a dead thread, but Ill take a punt. I dusted my old Nexus 4 off the other day, which had exactly the same issue with the dead strip on the digitiser. I had tried replacing the screen and digitiser (I have up trying to get the original screen off the original digitiser). The issue remained, so I tried a full factory reset, but that also didn't work. I am now wondering if I should get a cheap motherboard, or try flashing the stock ROM again. Has anyone else had any luck with either?

[Q] Screen looks weird after replacement.

Hello, everybody!
I recently replaced my Nexus 7's screen and digitizer and now my screen looks really bad.
Can anyone point me in the right direction on how to fix it?
I've tried taking everything apart, twice, to see if maybe I hooked a wire wrong or something but I get the same results.
mixer5911 said:
Hello, everybody!
I recently replaced my Nexus 7's screen and digitizer and now my screen looks really bad.
Can anyone point me in the right direction on how to fix it?
I've tried taking everything apart, twice, to see if maybe I hooked a wire wrong or something but I get the same results.
Click to expand...
Click to collapse
screen from ebay?
anarchyuk said:
screen from ebay?
Click to expand...
Click to collapse
Yeah... I'm beginning to think it's defective. I've already contacted the seller
mixer5911 said:
Yeah... I'm beginning to think it's defective. I've already contacted the seller
Click to expand...
Click to collapse
this is what's put me off getting one from ebay, mines only a week old and cracked due to not that much thumb pressure debating cutting my losses and throwing it in the bin if this is how weak the screens are
You should really change that. There is no way that is a software issue

[Q] Screen replacement issue...

So I dropped my phone over the weekend and only half of the screen is working. I took it into a local repair guy who comes highly recommended and has excellent reviews.
He tried replacing the entire screen component with two different replacements and there was white banding/lines down the screen both times. He thinks his replacement parts were defective and that the issue has nothing to do with the phone, as there are no white lines with the stock cracked screen.
I'm rooted on cloudy stock and wondering if that has anything at all to do with those lines? For some reason i feel like I remember hearing about this issue on the occasional custom ROM.
Hes getting more in tomorrow and will try again and let me know.
Does anyone have any idea?
Thanks.
Sent from my Galaxy Nexus using Tapatalk
madboymatt said:
So I dropped my phone over the weekend and only half of the screen is working. I took it into a local repair guy who comes highly recommended and has excellent reviews.
He tried replacing the entire screen component with two different replacements and there was white banding/lines down the screen both times. He thinks his replacement parts were defective and that the issue has nothing to do with the phone, as there are no white lines with the stock cracked screen.
I'm rooted on cloudy stock and wondering if that has anything at all to do with those lines? For some reason i feel like I remember hearing about this issue on the occasional custom ROM.
Hes getting more in tomorrow and will try again and let me know.
Does anyone have any idea?
Thanks.
Sent from my Galaxy Nexus using Tapatalk
Click to expand...
Click to collapse
The digitizer might be broken. If that's the case, you're better off getting a replacement as digitizers can cost about $300-$500.
simon_lefisch said:
The digitizer might be broken. If that's the case, you're better off getting a replacement as digitizers can cost about $300-$500.
Click to expand...
Click to collapse
The digitizer and LCD assembly is around $100 on eBay...not $300.
Sent from my Galaxy Nexus using Tapatalk
madboymatt said:
The digitizer and LCD assembly is around $100 on eBay...not $300.
Sent from my Galaxy Nexus using Tapatalk
Click to expand...
Click to collapse
Oh wow, it dropped significantly since the last time I checked. Regardless, that could be part of the issue. She you say you replaced the whole screen component, are you talking about the digitizer as well?

[Help] Dead screen before and after screen replacement

Hey guys, so a couple of weeks ago I dropped my N4 in water for about 10 seconds, as I was attempting to shut it down the screen flickered and it all went dead.
Fine, so after a week taken apart and in rice the battery is screwed, standard stuff, bought an OEM replacement battery, and then it turned on, worked as it should, except the screen was completely dead, no backlight no nothing.
Again fine, I order a non-OEM screen/digitizer/frame assembly, it arrived today and after being god damn sure everything is correctly assembled I power it on to find the screen is still completely off even though the phone is starting up and working normally (I can hear it unlocking, I can receive calls etc)
Is there another component that has to do with the signal to the screen that may have suffered from the water damage?
Bump. Can anyone shed any light on anything else to try?
Biggles_me said:
Bump. Can anyone shed any light on anything else to try?
Click to expand...
Click to collapse
My guess is you got a bad screen. There's lots of cheap ones out there. See if you can return it
Sent from my Nexus 5 using XDA Free mobile app
jd1639 said:
My guess is you got a bad screen. There's lots of cheap ones out there. See if you can return it
Sent from my Nexus 5 using XDA Free mobile app
Click to expand...
Click to collapse
I suppose it's a shame I can't know for sure cause the new one could be faulty, and the old one could be water damaged in some way.
Biggles_me said:
I suppose it's a shame I can't know for sure cause the new one could be faulty, and the old one could be water damaged in some way.
Click to expand...
Click to collapse
Hang on, I just realised the digitizer works on both screens, I can unlock it and navigate what I remember from my layout just fine, it's just the display on the new one and the old one, surely that means something else is broken on the mainboard perhaps?

Categories

Resources