Its been a few months since Ive bothered trying to figure out how to fix my Galaxy Tab 4, SM-T230NU, but Im finally getting around to fixing it. It sat in my closet for a few months simply because I did not have the time to fix it. It's soft bricked (loads the Samsung Galaxy Tab 4 bootscreen, but stays stuck on the single Samsung logo). Its not hard bricked as power turns on, but it is soft-bricked. Will running NE2 I found in the firmware section fix the soft-brick? I just downloaded odin 3.09, and right now NE2 is downloading through Mega.nz......any help would be appreciated....
jxcorex28 said:
Its been a few months since Ive bothered trying to figure out how to fix my Galaxy Tab 4, SM-T230NU, but Im finally getting around to fixing it. It sat in my closet for a few months simply because I did not have the time to fix it. It's soft bricked (loads the Samsung Galaxy Tab 4 bootscreen, but stays stuck on the single Samsung logo). Its not hard bricked as power turns on, but it is soft-bricked. Will running NE2 I found in the firmware section fix the soft-brick? I just downloaded odin 3.09, and right now NE2 is downloading through Mega.nz......any help would be appreciated....
Click to expand...
Click to collapse
Flash the right firmware for your device and see if it boots. If it doesn't boot within 20minutes after flashing, simply reboot into recovery and factory reset.
-DUHA
When I rooted the device, gaining root on the 230NU was abit of work, so I had to go through a lot of in and out holes just to root the sucker, and then a week or two later there are many different ROMs available for the 230NU...I'm shocked that someone finally found a workaround for the marvel processor in the 230NU because the 8 I believe has a snapdragon and/or euronoyx (however you spell it)
jxcorex28 said:
When I rooted the device, gaining root on the 230NU was abit of work, so I had to go through a lot of in and out holes just to root the sucker, and then a week or two later there are many different ROMs available for the 230NU...I'm shocked that someone finally found a workaround for the marvel processor in the 230NU because the 8 I believe has a snapdragon and/or euronoyx (however you spell it)
Click to expand...
Click to collapse
It works, im running 4.4.2 stock....Im about to look into some information about rooting.....When I got everything running smooth I got a system update message, so right now it's going through a system update......Do you have any good source of information for rooting the SM-T230NU ???
jxcorex28 said:
It works, im running 4.4.2 stock....Im about to look into some information about rooting.....When I got everything running smooth I got a system update message, so right now it's going through a system update......Do you have any good source of information for rooting the SM-T230NU ???
Click to expand...
Click to collapse
Here
Related
Hi!
I just rooted my Samsung GT-I9505 a few weeks ago with Odin v3.07 and CF-Auto-Root-jflte-jfltexx-gti9505.tar.md5.
Note that I didn't install any custom ROM.
It worked fine until now.
When I turned my phone off, it got stuck in reboot. The screen is black with a "Android OS is upgrading.. Opening all applications."
It's been 30mins and it just stayed there so I decided to take the battery off, put it back in and turn myphone on.
Now it's just stuck with the samsung logo. And whenever I factory reset and reset cache it, it just get stuck with a black screen with a "Android OS is upgrading.. Opening all applications."
Did I just bricked my phone? Is there any way to fix this?
Any help would be deeply appreciated. Thanks!
Wrong section maybe?
circlesnpigs said:
Hi!
I just rooted my Samsung GT-I9505 a few weeks ago with Odin v3.07 and CF-Auto-Root-jflte-jfltexx-gti9505.tar.md5.
Note that I didn't install any custom ROM.
It worked fine until now.
When I turned my phone off, it got stuck in reboot. The screen is black with a "Android OS is upgrading.. Opening all applications."
It's been 30mins and it just stayed there so I decided to take the battery off, put it back in and turn myphone on.
Now it's just stuck with the samsung logo. And whenever I factory reset and reset cache it, it just get stuck with a black screen with a "Android OS is upgrading.. Opening all applications."
Did I just bricked my phone? Is there any way to fix this?
Any help would be deeply appreciated. Thanks!
Click to expand...
Click to collapse
From your post I see you got gt-i9505 and that is plain Galaxy S4, not Galaxy S4 Active (gt-i9295). Although the phones are quite like twins, try S4 forum instead.
But if you really have S4 Active (again, it's gt-i9295, it has 3 physical buttons insted of just Home under the screen) and you flashed 9505 as root method, this forum deals with your approach and this particular post might be of interest. There is however even easier way and that is to root from now working CWM recovery for i9295.
Either way good luck with your phone :fingers-crossed:
almec said:
From your post I see you got gt-i9505 and that is plain Galaxy S4, not Galaxy S4 Active (gt-i9295). Although the phones are quite like twins, try S4 forum instead.
But if you really have S4 Active (again, it's gt-i9295, it has 3 physical buttons insted of just Home under the screen) and you flashed 9505 as root method, this forum deals with your approach and this particular post might be of interest. There is however even easier way and that is to root from now working CWM recovery for i9295.
Either way good luck with your phone :fingers-crossed:
Click to expand...
Click to collapse
Yeah! Sorry. Posted it in the wrong section. Just don't know how I'll delete this post.
Aww.. Thanks! Hopefully it'll be fix before the morrow.
Please pay attention to the device forum in which you seek help
There are many models of S4 and use of some software will turn your device into a $700 paperweight
Thread moved to correct forum
FNM
try to flash
try to flash in kernel again.mean cf kernel
Hey guys. Ive had a note 3 before in the past and have used the Root DelaVega to root successfully. This was early in the year. I sold my old note 3 for an HTC One. Well today i traded my HTC One back for a note 3 as i missed the Note 3. As soon as i came home i attempted to use the Root DelaVega method to foot (just like i did before) and immediately it failed.
I have been stuck on a screen saying "firmware update encountered an issue - select recovery in Kies" so i tried Kies 3.2 however it says my device is not compatible. Come to find out after doing research (talking to the original owner i traded my HTC One for) the Note 3 i have is on the latest version of KitKat 4.4.2 that is not compatible with the Root DelaVega method or any root method - so i screwed that up. I can successfully boot in and out of download mode. Ive tried to flash N900XXUDNA6 4.4.2 in Odin several times, it begins then fails almost immediately and the bar on the phone itself (in download mode) begins then freezes shortly after beginning. Ive also tried to flash N900XXUDNC1 JellyBean thru odin and get the same results - almost immediately fail and the blue status bar on the phone freezes when it barley begins. What else can i do??? am i totally screwed? Ive been researching and trying to fix this for 6 straight hours now! My gf is about to kill me for being online so long Is there anything i can do at this point? Am i stuck.
Do you know what Region the phone was originally? I had a similar issue and I had to get the Hong Kong (in my case) version of a stock ROM and flash that to get things working again. Not all partitions are the same - you might need a PIT file to match your original region and then flash the ROM.
What info do you get in DL mode?
Journyman16 said:
Do you know what Region the phone was originally? I had a similar issue and I had to get the Hong Kong (in my case) version of a stock ROM and flash that to get things working again. Not all partitions are the same - you might need a PIT file to match your original region and then flash the ROM.
What info do you get in DL mode?
Click to expand...
Click to collapse
Yes the phone is for AT&T so it's US. When I go into DL mode Knox counter is still 0x0. Is there a certain firmware I need then to match with the AT&T model? Or a pit?
jthornton71707 said:
Yes the phone is for AT&T so it's US. When I go into DL mode Knox counter is still 0x0. Is there a certain firmware I need then to match with the AT&T model? Or a pit?
Click to expand...
Click to collapse
Go to Sammobile and see if you can find the version you had, sounds like an older JB if kingo app didn't trip Knox. Reflash that using ODIN.
I don't know if there was a problem with American bootloader, see if there's an AT&T Note 3 forum. Might find answers there...
jthornton71707 said:
Hey guys. Ive had a note 3 before in the past and have used the Root DelaVega to root successfully. This was early in the year. I sold my old note 3 for an HTC One. Well today i traded my HTC One back for a note 3 as i missed the Note 3. As soon as i came home i attempted to use the Root DelaVega method to foot (just like i did before) and immediately it failed.
I have been stuck on a screen saying "firmware update encountered an issue - select recovery in Kies" so i tried Kies 3.2 however it says my device is not compatible. Come to find out after doing research (talking to the original owner i traded my HTC One for) the Note 3 i have is on the latest version of KitKat 4.4.2 that is not compatible with the Root DelaVega method or any root method - so i screwed that up. I can successfully boot in and out of download mode. Ive tried to flash N900XXUDNA6 4.4.2 in Odin several times, it begins then fails almost immediately and the bar on the phone itself (in download mode) begins then freezes shortly after beginning. Ive also tried to flash N900XXUDNC1 JellyBean thru odin and get the same results - almost immediately fail and the blue status bar on the phone freezes when it barley begins. What else can i do??? am i totally screwed? Ive been researching and trying to fix this for 6 straight hours now! My gf is about to kill me for being online so long Is there anything i can do at this point? Am i stuck.
Click to expand...
Click to collapse
Hi mate,
if you are stuck, maybe you can try this.
http://forum.xda-developers.com/show....php?t=2701062
it's a way to unbrick your software.
and if the older owner of your N3 said it's on the latest firmware of kitkat.
maybe your problem is the firmware in the sammobile were before the firmware you have install on your device via OTA update.
Yours firmware came throw out via OTA update and with some reason you can't see any latest firmware USA N900A in sammobile.
try the method in the link and reply if you have been successful.
cumps
Ik Knox is 0×0,then u can try samsung service centre ?
Sent from my SM-N900 using XDA Premium 4 mobile app
Hello XDA community
Iam a longtime lurker here what a great community with a wealth of information.
I have a a grasp of the basic rooting and flashing custom roms/kernels over the past few years on my old galaxy s3.
My partner had an OTA update for her gt9505 galaxy s4 today whicg seemed to hang while updating, unfortunately she pulled the battery mid update
The phone can enter download odin mode but i cant get it to open the recovery. I have flashed (using odin) a few different compatible roms they finish installing via odin but when the phone restarts it just turns off it will not go past the galaxy white and black screen. It will turn off again.
It has never been rooted, i spent many hours trying to get to the OS but it fails when restarting. I decided to flash CF-Auto root hoping to get access to recovery. Again it successfully installs cf auto root and restarts and then turns off.
It seems everything i flash never ever saves to memory.
What else can i try please? iam happy installing a custom rom but i cant get it working. iam afraid its bricked for good without expensive repairs.
thanks
lol i managed to get it working.
It was a combination of dead battery and multiple problem cables not charging the phone.
I just swapped from my Amaze 4g, to a used Note 3, and I'm a little lost as far as where I should start.
It says that it's on 4.4.2, and that I cannot update due to a modified system.
Basically, I would like to get updated to 5.1.1 (or as close as is official for the Note 3), and root it.
I'm afraid I'm not familiar with Samsung devices, and because I purchased this from ebay, I don't know how to tell the exact state that the former user put it in (I expected they would return it to stock prior to selling).
It's currently a T-Mobile branded, SM-N900T, on 4.4.2, build is KOT49H, security software MDF v1.0 release 2. Kernel is 3.4.0-660648.
It is supposedly unlocked for carriers, though I have not attempted a SIM card use yet, until I can tell that what I have is a valid device and the IMEI is checked out.
Any thoughts on how to validate the IMEI, and sort out how to get my new phone up to date would be appreciated. As I stated, I expected the vendor would have returned it to stock, but that is clearly not the case, so I don't want to accidentally boot loop it by doing something I shouldn't. I have not owned a Samsung before, so I want to be careful on how it differs from my Nexus 7, Amaze 4g, and Droid X, as they're all obviously very different in the OS area.
Thank you for the help1
Download tbe stock 4.4.2 rom and use odin to install. Then you will get the OTA updates.
Sent from my SM-N900P using Tapatalk
There is no stock 5.1.1 for note 3, only cm12.1/ aosp. Latest is 5.0 and you can use odin to flash. Maybe it's rooted that's why you can't update.
bladebarrier said:
I just swapped from my Amaze 4g, to a used Note 3, and I'm a little lost as far as where I should start.
It says that it's on 4.4.2, and that I cannot update due to a modified system.
Basically, I would like to get updated to 5.1.1 (or as close as is official for the Note 3), and root it.
...
Thank you for the help1
Click to expand...
Click to collapse
Some apps to install from Play Store...
Phone INFO Samsung - this will tell you all about your phone and the firmware etc.
Root Checker Basic - tells you if you are rooted or not.
SuperSU - this is so valuable you should buy the Pro licence. Chainfire does some great work for our phones.
TWRP - I have the zip version on my extSDCard and an Odin version on PC in case I have to rebuild from a Stock firmware. CWN works OK but most ROM builds seem to be for TWRP I think and a backup from one will not work on the other.
I don't know your previous phone so you probably need Odin v3.09 - this sits on PC and lets you flash firmware to the phone. (connected by USB)
For which you need Samsung USB drivers so the PC will recognise the phone. Install on PC before connecting phone.
Then do some browsing and find the processes to root your phone and install the ROM you want. If you just want Stock and access to all your phone, you can root it after flashing the original v5.0 download (from Sammobile or similar site - note on Sammobile you need a free account to DL) and then install Custom recovery (if wanted - it WILL trip the Knox flag but that may not matter given it's 2nd hand and might already be tripped anyway)
Read, make SURE you understand what is being said BEFORE you do anything - ask if you don't.
Good luck...
N9005 Lollipop brick
Hi All, just need a huge help here, a friend of mine has been using a N9005 which was auto restarting, she went online and downloaded this firmware...N900AUCUEOC1_N900AATTEOC1_N900AUCUEOC1_HOME.tar.md5....2.5GB in size...and flashed it, but the phone is stuck in boot loop even after recovery wiping data and cache, the phone can boot into download mode but re flashing the firmware always fails.....is there a solution for this.....please help
Thank you all for the info, especially the detailed info from Journyman16. I checked, and it is flagged as custom, which is fine, so I'm going to go ahead and try to return to mostly stock, update it, and root it.
Ok, everything went well. I had to do two attempts at rooting, but I think it's just one of those things where sometimes it doesn't restart into the process every time.
All seems good. I'm on 5.0, rooted, busyboxed, and smooth sailing.
Thank you all, again, for the tips. The Note 3 is running very well. Thank you to all of the devs that have made this process so refined. I've donated to you before, and did so again today. It's outstanding to have such well versed coders, on XDA, helping out the community.
mjmbirige said:
Hi All, just need a huge help here, a friend of mine has been using a N9005 which was auto restarting, she went online and downloaded this firmware...N900AUCUEOC1_N900AATTEOC1_N900AUCUEOC1_HOME.tar.md5....2.5GB in size...and flashed it, but the phone is stuck in boot loop even after recovery wiping data and cache, the phone can boot into download mode but re flashing the firmware always fails.....is there a solution for this.....please help
Click to expand...
Click to collapse
You have never learned not to ask in others posts? What does your problem has to do with this topic at all?
When you need help. Just click on Q&A then Create a new thread. How hard is it?
Hi guys,
Phone: Samsung Galaxy S8 SM-G950F
I was given this phone by a friend of mine who attempted to install factory binary or something or rather.
He can not recall exactly what he attempted to do, however.... This is the condition it is in now..
I have no clue where to even begin with it.
Any and all help would be greatly appreciated.
Drew.
Blind bet is that freund is finished with this phone if doesn't go to download mode.
Your are need to download official firmware from Sammobile and flash it through odin .
First thing is to see if odin detects it in download mode.
Ive managed to get an almost bricked s8 at least alive and kicking a few days ago by reflashing *only* the AP file (stock 8.0 XSA from Sammobile) which at the very least got me around the locked bootloader issue. Its just killed the IMEI in it.
In a couple of days ill get another shot at restoring it to full funtionality but ive already replaced it anyway so its most likely only going to be used for DeX now.
Ive had no responses to my post so meh.
Which exact one did you use Funkymonkey..?
Thanks in advance.