Related
i have been doing alot of rom upgrade via clockwork and this is the first time my phone brick.
i tried the vol up, vol down and power button at the same time and it just brings me to "vibrant samsung" screen.
i also tried removing battery, hold vol up, vol down and insert battery, it goes to a screen where it says downloading. but didnt move for hours.....
and if i switch on normally, it just keep restarting on vibrant screen.
how do i solve this problem?
You have to use odin to flash back to stock....
That's what the download screen is for.
From that downloading mode screen you can odin it back to stock.
http://forum.xda-developers.com/showthread.php?t=734475
lazylilsnoop said:
i have been doing alot of rom upgrade via clockwork and this is the first time my phone brick.
i tried the vol up, vol down and power button at the same time and it just brings me to "vibrant samsung" screen.
i also tried removing battery, hold vol up, vol down and insert battery, it goes to a screen where it says downloading. but didnt move for hours.....
and if i switch on normally, it just keep restarting on vibrant screen.
how do i solve this problem?
Click to expand...
Click to collapse
removing battery, hold vol up, vol down and insert battery, Have Odin up and running then plug in your cable. Then let go of the button
yea, i found that page too. but anyone can get the link working?
thanx!!!
lazylilsnoop said:
yea, i found that page too. but anyone can get the link working?
thanx!!!
Click to expand...
Click to collapse
can't see the page?
here i quoted the OP
justanothercrowd said:
T959 (US T-Mobile version of the Galaxy S) Firmware that can be flashed through Odin to restore all partitions to the way your phone was shipped to you.
WARNING!!! THIS WILL WIPE ANY DATA ON YOUR DEVICE, IT WILL REPLACE YOUR BASEBAND, KERNEL, RECOVERY AND OS.
JFD ODIN Images from Samsung (PDA)
www.justanotherdev.slackdev.com/T959UVJFD.tar
MD5:632730f6b637f53e5b10e5cbc8b966a7
512 PIT File (PIT Extract first!)
www.justanotherdev.slackdev.com/s1_odin_20100512.rar
MD5:b5628c8e183fdd8f4c703321ca40e33a
ODIN
www.justanotherdev.slackdev.com/Odin3.rar
ALL 3 Files plues the root update.zip
http://tinyurl.com/2bc5b6r
thx to KopyKatKiller
INSTRUCTIONS!
1.Your Device must be in DOWNLOAD mode to use ODIN.
2.Get your phone into Download mode by holding vol down and power.
3.THEN connect your phone to the USB. (some folks have had luck doing it in reverse..connecting the USB then Power and vol down)
4.Open Odin and load each file with it's corresponding field..PIT,PDA,CSC etc. (In this case we just use the PDA and PIT)
5.Don't check anything else, the other two boxes should be checked by default (Auto Reboot and Reset Time)
6.Hit "start"! be patient!
NOTE: COM3 worked fine for me. COM should not matter as long as you are using the correct drivers.
Finally we get some U.S love from samsung firmwares.
For those looking the Nandroid method it is in the post below but only recovers ,system, data, cache and datadata. Not your kernel/recovery or BASEBAND/RADIO (Modem.bin)
Thx to all helping work on the Vibrant. Especially Youneek, Scepterr, MS_Guru, Wes Garner, rhcp0112345, and anyone I may have forgot.
Twitter
Click to expand...
Click to collapse
sorry, what i meant was the link to download odin.
all link by "justanothercrowd" is not working
Get in download mode like you have before then..
Use the Vibrant Toolkit and then click Flash to Stock and then press "Reboot into Download + Start ODIN" (ignore the "Check that USB debugging mode is enabled" because you're already in download mode), it'll open up ODIN and then follow the instructions for using ODIN.
http://forum.xda-developers.com/showthread.php?t=954509
From bay_wolf's post, some information about setup of odin,
When you select the PIT and PDA files, it should default to the installed location and if not then browse to where you installed AIO Vibrant Toolbox as the files are in there.
Click to expand...
Click to collapse
Note: there are instructions on how to use odin on the Flash To Stock screen. All the files you'll need will be downloaded with the download for the vibrant toolkit.
I've had this problem and freaked when i couldn't find a download to Odin, so I used the vibrant toolkit and it worked.
Here's the download link from his thread (credit to bay_wolf): http://www.multiupload.com/G3LUINMUE0
THANX ALOT GUYS!!!!!!!
now gonna start to update it to http://forum.xda-developers.com/showthread.php?t=1021383
just another quick question, which rom are you guys using? i came from bionix rom to the simply galaxy v3.0, it doesnt seem to b fast and smooth. any other recommended rom?
Try some EDT roms...beast...Malice, Trigger, or Bi Winning.
Flash back to stock too.
I use simply Galaxy with Crysis Sensation theme (TWiz 4.0 + tweaks) & DamianGTO Gold v2.0 kernel (not available on XDA). Then use an app called Blade buddy to set up all Stagefright tweaks (under advanced settings) and debug.sw.hf then menu > apply > save. Quadrant scores 2200+.
Trigger is really good (2.2) and there's a cool new theme called Vibrant HD for it.
Haven't tried CM7 but it looks cool, lots of themes with it.
Hi
For the beginning i want to say thx to the people who will try help me.
Samsung Note 3 SM-9005
Rom: NB3 4.4.2 (kitkat)
I should post it as a reply to the chainfire's post on cf auto root but i can't cause i am a new on xda (and he didn't allow me )
So what is my problem ?
When i tried root with CF all is ok but when odin say 'PASS' there is no recovery boot (the install process, the red android logo)
What i have ? > After my flash my phone try to boot (with Se Enforcing + 2 other stuff blue red and yellow i guess) but my phone can't boot (yes even boot) he only reset and try re-booting.
chainfire's say
*NOTE: Sometimes the device does *not* boot into recovery mode and root your device. Just do the entire procedure again if this happens. If it still will not install root and such, make sure that in Odin "Auto Reboot" is not checked. Then after flashing, pull the battery, and boot with VolUp+Home+Power button to boot into recovery manually. This will start the install process.*
Click to expand...
Click to collapse
So i tried it, i unchecked the auto-boot, flash my phone pull the battery and press the button (without the battery), and after my phone turn off.
When i turn on >> same issue boot loop all time
And to have access on the phone i must go on the downlaod mode and click restard phone...
Well if u could help me .... 90% of my app require root x) :laugh:
Is this the file you used? There's 2 files, one for 4.4 and the other for 4.3. Try flashing the file again.
Yes i used this file
i forgot to say that kingo root is so buged i mean i try also to root with him (on 1s)
He put my phone on download, install the recovery ect
Result: a fake root, in fact even if i have SuperSU (he installed) He said me that i have no binnary installed
I also checked on "Root Checked" no root here
BUT on download mode: custom os + custom binnary
And his chinese recovery work
1 hour ago i used my GN2 to see if maybe it's my computed who have issue with kingo root
Result: Root perfectly my phone
I also forgot to say that i used different odin (1.85,3.09 ect) on admin
And i tried the NA6's rom (maybe was the rom ^^' but nop still no root)
French's user said:
Hi
So i tried it, i unchecked the auto-boot, flash my phone pull the battery and press the button (without the battery), and after my phone turn off.
When i turn on >> same issue boot loop all time
And to have access on the phone i must go on the downlaod mode and click restard phone...
Well if u could help me .... 90% of my app require root x) :laugh:
Click to expand...
Click to collapse
I re-read your reply and I'm a little confused. Did you pressed all buttons after removing the battery? Also, there is no restart phone in download mode, you can only get out of download mode by pressing power button for a few seconds or remove the battery.
Lastly, maybe check you have the correct samsung usb drivers and reactivation lock is off.
hey_joe said:
I re-read your reply and I'm a little confused. Did you pressed all buttons after removing the battery? Also, there is no restart phone in download mode, you can only get out of download mode by pressing power button for a few seconds or remove the battery.
Lastly, maybe check you have the correct samsung usb drivers and reactivation lock is off.
Click to expand...
Click to collapse
Well i know but i didn't even really understand the process to manually boot the recovery (the chainfire's quote)
what i did ? i flash my phone when odin say "reset" i just pull the battery on the table and next press buttons (Volup+home+power)
My phone turn off i replace the battery and i get the booting loop
Maybe my way to process is wrong, i don't even know chainfire don't really explain in details the way to do it....
For the driver i deleted all and re-installed by kingo but in fact all time my device is detected (in all mode) and COM if alway here (also the flash is correct)
I think maybe my process is badly done (maybe i can't understand cause im french)
Here's how I would normally do it.
- download the file and extract to a folder/location of choice
- put phone in download mode by pressing power + vol down + home button all at the same time until something comes up on the screen then let go of the buttons then press vol up then connect to usb on pc
- go to where you extracted the downloaded file, open odin and put the tar.md5 file in the PDA slot and click start
Odin will flash file and automatically restart to apply root ( red android with red letters ) then restart again to android.
OMG dude that work thx to you :laugh::laugh::laugh::laugh::laugh::laugh:
Ok the last post i mean i didn't understand the process of the boot recovery manually (with autoboot unchecked)
But i least this time i used a different thing- what ?- A nokia usb cable
And this time that work and im sure before i did all u said to me.
I worked on 2 night x)x)
Anyway dude thx to help me
No problem.
Enjoy your phone :good:
I had an error about verifying the file signature and found a fix buried in a thread:
http://forum.xda-developers.com/showthread.php?t=943415&page=5&nocache=1
It seems the phone needs to reboot into recovery mode instead of manually entering (you can't hold both volume buttons and power, for some reason it is different i.e. the camera button is the select button instead of menu). I had to do what Speardroid notes below to get update.zip to go with no error.
For those who have been hanging on the edge of their seats waiting to see if my struggles ended....they haven't totally...but I have finally managed some success.
it seems to be totally a hit or miss thing...but I have been able to get into CWR, red text and all, twice....enough to do a backup of my ROM and flash the DL17 clean ROM along with the two updates (email and social)
The only way I've been able to get into CWR....is to Odin the .pit and .tar file from this thread over and over again...until for some reason after it says reset in Odin my phone resets directly into manual recovery mode. This has happened twice, and both times I had to use the soft key to apply update.zip and both times it got me into CWR.
Manual rebooting with vol up and down takes me to the original recovery mode where the camera button works and flashing update.zip doesn't.
Even doing the Odin technique, when it doesn't fail, typically just restarts my phone into Android...except for two times.
So basically, I hope I don't need to flash anymore .zip files because getting back into CWR is like playing a game of roulette.....although strangely, I've never actually done that.
Click to expand...
Click to collapse
Last week, my yotaphone 2 informed that there is a system update from yotaphone. I downloaded and updated but then my phone cannot work. It show only black start screen with word "Android" until battery empty.
I tried to android recovery mode (hold power and volume up),
it show that the error is "e:cannot load volume /misc!".
And I do not know how to solve that problem.
Please help me!
leviet4 said:
Last week, my yotaphone 2 informed that there is a system update from yotaphone. I downloaded and updated but then my phone cannot work. It show only black start screen with word "Android" until battery empty.
I tried to android recovery mode (hold power and volume up),
it show that the error is "e:cannot load volume /misc!".
And I do not know how to solve that problem.
Please help me!
Click to expand...
Click to collapse
You can probably recover.
To reflash a full firmware image you could try the relatively user-friendly yotaflasher application and ROM images from here. I haven't used this myself, but it's software by Yota, so should be safe. You can ask it not to touch /data, to preserve apps, settings etc.
A less user friendly way to reflash a full firmware image:
- Download a full firmware image (EU 1.60 flashable version here, let me know if you require a different one)
- With the phone off, press vol down + power until you see "Downloading ...."
- If you can't turn the phone off normally, keep vol down + power for at least 15 seconds till phone reboots, keep holding till you end up with "Downloading ...."
- connect to a PC with adb+fastboot with a USB cable
- You can now boot TWRP image (fastboot boot recovery_twrp_yd201_alpha2.img , see here.
- if you have important files on your phone, you can back them up now by using adb shell/adb pull (e.g. adb pull /sdcard/Pictures/yeti_sighting.jpg)
- In TWRP go to advanced -> sideload and confirm
- now you can sideload a ROM image from the PC with adb sideload <image>.zip, it should show progress while it's uploading the firmware. If it errors, you probably haven't confirmed initiating sideload in previous step.
- wipe cache&dalvik and reboot
thank you, the first way worked and my phone runs normally now.
thank you
Help please
SteadyQuad said:
You can probably recover.
To reflash a full firmware image you could try the relatively user-friendly yotaflasher application and ROM images from here. I haven't used this myself, but it's software by Yota, so should be safe. You can ask it not to touch /data, to preserve apps, settings etc.
A less user friendly way to reflash a full firmware image:
- Download a full firmware image (EU 1.60 flashable version here, let me know if you require a different one)
- With the phone off, press vol down + power until you see "Downloading ...."
- If you can't turn the phone off normally, keep vol down + power for at least 15 seconds till phone reboots, keep holding till you end up with "Downloading ...."
- connect to a PC with adb+fastboot with a USB cable
- You can now boot TWRP image (fastboot boot recovery_twrp_yd201_alpha2.img , see here.
- if you have important files on your phone, you can back them up now by using adb shell/adb pull (e.g. adb pull /sdcard/Pictures/yeti_sighting.jpg)
- In TWRP go to advanced -> sideload and confirm
- now you can sideload a ROM image from the PC with adb sideload <image>.zip, it should show progress while it's uploading the firmware. If it errors, you probably haven't confirmed initiating sideload in previous step.
- wipe cache&dalvik and reboot
Click to expand...
Click to collapse
I have yotaphone model YD206, but I am in the USA and would like to root and load the best rom I can for my device, it doesn't even have google apps on it. Thanks for any and all help
Kevinreid1 said:
I have yotaphone model YD206, but I am in the USA and would like to root and load the best rom I can for my device, it doesn't even have google apps on it. Thanks for any and all help
Click to expand...
Click to collapse
Root the phone using methods written on this forum > download build 1.60 flammable zip > flash that.
If all you want is Google apps then root the phone then download and flash a gapps package. The full Yota build zip is recommended though.
Can't download yotaflasher application from the link... does anybody have the exe file?
SteadyQuad said:
You can probably recover.
To reflash a full firmware image you could try the relatively user-friendly yotaflasher application and ROM images from here. I haven't used this myself, but it's software by Yota, so should be safe. You can ask it not to touch /data, to preserve apps, settings etc.
A less user friendly way to reflash a full firmware image:
- Download a full firmware image (EU 1.60 flashable version here, let me know if you require a different one)
- With the phone off, press vol down + power until you see "Downloading ...."
- If you can't turn the phone off normally, keep vol down + power for at least 15 seconds till phone reboots, keep holding till you end up with "Downloading ...."
- connect to a PC with adb+fastboot with a USB cable
- You can now boot TWRP image (fastboot boot recovery_twrp_yd201_alpha2.img , see here.
- if you have important files on your phone, you can back them up now by using adb shell/adb pull (e.g. adb pull /sdcard/Pictures/yeti_sighting.jpg)
- In TWRP go to advanced -> sideload and confirm
- now you can sideload a ROM image from the PC with adb sideload <image>.zip, it should show progress while it's uploading the firmware. If it errors, you probably haven't confirmed initiating sideload in previous step.
- wipe cache&dalvik and reboot
Click to expand...
Click to collapse
glax87 said:
Can't download yotaflasher application from the link... does anybody have the exe file?
Click to expand...
Click to collapse
Just click on the YotaPhoneFlasher folder then click the file (yotaphone2_flasher.exe), and save to your harddisk.
Or you can try this link straight to the yotaphone2_flasher.exe file.
https://drive.google.com/file/d/0B0KC5E0zkBYmcHAzMEFKaHRvZ3M/view?usp=sharing
HOW
leviet4 said:
thank you, the first way worked and my phone runs normally now.
thank you
Click to expand...
Click to collapse
Dude I've just bought my phone, and it has the same problem. But I'm a complete noob, how did you fix it? Please, i've just bought it.
On RU build 134 when I tried to swap users my user with Defaut user, the phone blocked, the display is on (time is the same when first happend - just a freeze image) but I can't do nothing on phone. Is a way to reset? because on a normal way I would remove battery but yota dont have this option.
queser.info said:
On RU build 134 when I tried to swap users my user with Defaut user, the phone blocked, the display is on (time is the same when first happend - just a freeze image) but I can't do nothing on phone. Is a way to reset? because on a normal way I would remove battery but yota dont have this option.
Click to expand...
Click to collapse
The analogue method of pulling out the battery is pressing the POWER button for at least 10 seconds. The phone will reboot.
Thanks, I pushed vol down + Power and the phone restarted normaly.
PS: If you know where to get a book from Алекса́ндр Солжени́цын - Aleksandr Solzhenitsyn to read on yota display, send me.
SteadyQuad said:
You can probably recover.
To reflash a full firmware image you could try the relatively user-friendly yotaflasher application and ROM images from here. I haven't used this myself, but it's software by Yota, so should be safe. You can ask it not to touch /data, to preserve apps, settings etc.
A less user friendly way to reflash a full firmware image:
- Download a full firmware image (EU 1.60 flashable version here, let me know if you require a different one)
- With the phone off, press vol down + power until you see "Downloading ...."
- If you can't turn the phone off normally, keep vol down + power for at least 15 seconds till phone reboots, keep holding till you end up with "Downloading ...."
- connect to a PC with adb+fastboot with a USB cable
- You can now boot TWRP image (fastboot boot recovery_twrp_yd201_alpha2.img , see here.
- if you have important files on your phone, you can back them up now by using adb shell/adb pull (e.g. adb pull /sdcard/Pictures/yeti_sighting.jpg)
- In TWRP go to advanced -> sideload and confirm
- now you can sideload a ROM image from the PC with adb sideload <image>.zip, it should show progress while it's uploading the firmware. If it errors, you probably haven't confirmed initiating sideload in previous step.
- wipe cache&dalvik and reboot
Click to expand...
Click to collapse
Sir, i can't even get into recovery mode, i get this problem like it suddenly happen and my battery was 38%.. i was on facebook and it hang and then reboot and then stuck at "POWERED BY ANDROID".
I try to get into recovery mode by pressing volume up + power button, it restart again to "POWERED BY ANDROID"
When i pressing volume down + power button, it show downloding... , and i try to flash it using yotaflasher with HK Firmware 5.0.
When it is done, the phone reboot.
And it still stuck at "POWERED BY ANDROID"
What is the real problem ?
Please help!!!
While trying to solve the network issue on my Yotaphone 2 I managed to brick my phone. He is dead! But since it is a Snapdragon inside it can be fixed.
I need a help from someone who has rooted his Yotaphone2!
I need files from Yotaphone2 software: rawprogram0.xml and patch0.xml
Please!!!
hlmboy said:
Sir, i can't even get into recovery mode, i get this problem like it suddenly happen and my battery was 38%.. i was on facebook and it hang and then reboot and then stuck at "POWERED BY ANDROID".
I try to get into recovery mode by pressing volume up + power button, it restart again to "POWERED BY ANDROID"
When i pressing volume down + power button, it show downloading... , and i try to flash it using yotaflasher with HK Firmware 5.0.
When it is done, the phone reboot.
And it still stuck at "POWERED BY ANDROID"
What is the real problem ?
Click to expand...
Click to collapse
You need to keep pressing the power up button after the showing of "POWERED BY ANDROID", the power does not need to be pressed after then.
If you can still not reach recovery, you probably have a broken recovery (maybe wrong version) and something else is messed up.
When you flash recovery, you need to instantly go into recovery mode by pressing +/up on calling the according command
(fastboot reboot).
It does not look like you changed file system related things, did you change anything on your system/with root permissions?
Are you sure the installation process went without failure etc?
Getting out the cause (kernel logs etc) would be a bit hard without getting into recovery mode[and maybe also nonworking kernel], like stated out here
https://android.stackexchange.com/q...n-i-recover-files-from-a-phone-that-wont-boot
**Before you comment, all I need are links to guides. You don't have to tell me step for step, I wouldn't do that do ya**
So earlier this week I was tweaking some settings through 3D Toolbox and I managed to essentially kill my phone. Now whenever my phone 'boots' it will show my startup screen with its usual vibration, after which the screen will go blank and it will not boot.
I killed it by enabling kernel exceptions in partition cleaning in the 3D Toolbox app; after I rebooted my device as told, it never booted again. I'm only trying to get my device image off it so I can dump the phone and start again, keep in mind I'm still learning about the operating system so I was bound to break something lol.
I'm worried what I've done has trashed my system image and I've essentially lost what was on my phone (lets hope that isn't the case :crying if anyone knows what I've done wrong and how to fix it please help a brotha out :fingers-crossed: Also when I try to go into recovery mode I'm greeted with "Recovery is not Seandroid Enforcing" if that helps, as I have no idea what it means.
If you want to pull off the data, try installing TWRP, booting into TWRP, mount the data partition, and copy data to your PC.
If you don't need anything on the phone, you could use Odin to flash the latest stock ROM.
audit13 said:
If you want to pull off the data, try installing TWRP, booting into TWRP, mount the data partition, and copy data to your PC.
If you don't need anything on the phone, you could use Odin to flash the latest stock ROM.
Click to expand...
Click to collapse
Thanks for the reply! But I'm very new to rooting and such and only touch what I know and what I need so I don't know how to go about this. If you could be so kind as to tell me the steps or to give me a guide I'd be on my way.
Thanks,
Jazzy
What is the model number shown in download mode?
audit13 said:
What is the model number shown in download mode?
Click to expand...
Click to collapse
SM-N9006 I believe is what you're looking for right?
Twrp.me your device
Use N9005 twrp as per previous N9006 posts .
JJEgan said:
Twrp.me your device
Use N9005 twrp as per previous N9006 posts .
Click to expand...
Click to collapse
Buddy I have no idea what these terms mean, I'm a big ol' noobie. I need my hand held lmao
This one.
https://dl.twrp.me/hltechn/twrp-3.2.3-0-hltechn.img.tar.html
JJEgan said:
This one.
https://dl.twrp.me/hltechn/twrp-3.2.3-0-hltechn.img.tar.html
Click to expand...
Click to collapse
Alright I've found a TWRP for it, do I download this and load it through ODIN? I'd still need to get a backup of my device before I'd wanna load an image up, so I still need a program to do that. Any suggestions for a program like that?
shnazzyjazzy said:
Alright I've found a TWRP for it, do I download this and load it through ODIN? I'd still need to get a backup of my device before I'd wanna load an image up, so I still need a program to do that. Any suggestions for a program like that?
Click to expand...
Click to collapse
Again, I have no idea what I'm doing with these, if you have a guide for stuff like this I'm all over that.
Step 2) Turn OFF your mobile and go to Download Mode by pressing and holding the Volume Down + Home Buttons together for few seconds followed by Power button then proceed with volume up.
Step 3) Now open ODIN on your PC and connect your Galaxy Note 3 to your computer.
Step 4) Once your phone is successfully connected to your PC, the ID:COM box on ODIN will turn blue (or yellow) and will show the COM port number.
Step 5) Click on pda in odin (if odin 3.09 choose AP) and choose the " TWRP .tar" file.
Step 6) Tick "Auto Reboot" and "F. Reset Time" options and make sure that "Re-Partition" is unchecked
!!!!DO NOT CHECK "Nand Erase All" IN ANY WAY!!!!
Step 7) Click on Start button in ODIN window to start the flashing process. The process will take few minutes to complete.
DO NOT UNPLUG USB CABLE WHILE EXECUTING THE PROCESS, YOU MAY BRICK YOUR PHONE!
Step 8) When the installation is completed, you read a "Reset " then a "Pass". your phone will restart
JJEgan said:
Step 2) Turn OFF your mobile and go to Download Mode by pressing and holding the Volume Down + Home Buttons together for few seconds followed by Power button then proceed with volume up.
Step 3) Now open ODIN on your PC and connect your Galaxy Note 3 to your computer.
Step 4) Once your phone is successfully connected to your PC, the ID:COM box on ODIN will turn blue (or yellow) and will show the COM port number.
Step 5) Click on pda in odin (if odin 3.09 choose AP) and choose the " TWRP .tar" file.
Step 6) Tick "Auto Reboot" and "F. Reset Time" options and make sure that "Re-Partition" is unchecked
!!!!DO NOT CHECK "Nand Erase All" IN ANY WAY!!!!
Step 7) Click on Start button in ODIN window to start the flashing process. The process will take few minutes to complete.
DO NOT UNPLUG USB CABLE WHILE EXECUTING THE PROCESS, YOU MAY BRICK YOUR PHONE!
Step 8) When the installation is completed, you read a "Reset " then a "Pass". your phone will restart
Click to expand...
Click to collapse
Bad news: I went and done this, it passed and everything but still won't turn on, or get past the loading screen. At this point I just wanna get my info off of it.
shnazzyjazzy said:
Bad news: I went and done this, it passed and everything but still won't turn on, or get past the loading screen. At this point I just wanna get my info off of it.
Click to expand...
Click to collapse
Burn it
Joking... So follow all the steps written by JJEgan, except for Step 6 : DON'T tick "Auto reboot" then flash.
Step 7 : When Odin shows "Passed", unplug the phone and take off the battery for 10sec.
Step 8 : Put the battery back and directly boot to recovery (Vol+, Power, Home).
shnazzyjazzy said:
Bad news: I went and done this, it passed and everything but still won't turn on, or get past the loading screen. At this point I just wanna get my info off of it.
Click to expand...
Click to collapse
Try again but only check f reset time and flash.
When you see the word "RESET" in the status window, remove the USB cable from the phone, remove the battery, replace the battery, use the buttons to boot into recovery.