I think i have a faulty unit because i can not connect to the internet at all (although it worked last sat morning when i got the unit but i did not try again until my number got ported)i have tried it on GSM only and checked all the settings over with the guy from T-Mobile and they are ok but if i put my sim in my Jam i get a connection with no problems.
The guy from T-Mobile says it may be beacuse i am on the fringe for UMTS reception but i get the U symbol and 4 bars on the strength meter but surely it should go on to GPRS if it can not get reception on UMTS as it would do for phone calls anyone any ideas ?
Start>Settings>Personal Tab>Phone>Band>"Select Network Type" and change to GSM (it's probably on Auto), then ok it all.
If you now connect over GPRS (which is what the above is to do - force it not to use UMTS at all), then you're ok.
Next thing is to go to a UMTS strong area, and do the settings but set back to Auto and see if u get 3G connection.
Hope it helps.
i just get the message ''warning:unable to change GSM/UMTS Band, please try again later''
thanks anyway
Hey guys, My device is Kaiser(TyTNII) and AT&T is my operator.
I live in Philadelphia, US.
Before yesterday my TyTNII can access HSDPA (with "H" symbol on the top right) when I try to use internet.
However, I use Kaiser Tweak to change some setting of my device and suddenly my kaiser doesn't recognize HSDPA network anymore, I mean it will only show "3G" on the top right. I have checked all the settings and everything seems fine.
HSDPA function is checked and same as in the Kaiser Tweak.
Can someone help me out here?
Thanks.
i have the same problem, cant go into hsdpa or even 3g only edge. and it seems to have happened after using kaiser tweak also.
Got some help over in the Kaiser forum that helped me. Go to your comm manager then settings/phone/ then go to band and switch your network type to wcdma. after it updated the network i switched back to auto and it seems to be working so far for me. hope this helps you out, something you could try.
I seem to have the same issue but the above solution doesn't help. Whenever I set the phone to do HSDPA through Connections I loss all data connectivity, once I turn it off HSDPA I get 3G.
Is it possible for radio settings to survive a hard rest / ROM upgrade or is the HSDPA side of my Tilt broken :-(
Any insight or help would be real appreciated.
Several times I have gotten "Warning: Unable to change GSM/UMTS Band, Please try again later."
JohnnyGTO said:
I seem to have the same issue but the above solution doesn't help. Whenever I set the phone to do HSDPA through Connections I loss all data connectivity, once I turn it off HSDPA I get 3G.
Is it possible for radio settings to survive a hard rest / ROM upgrade or is the HSDPA side of my Tilt broken :-(
Any insight or help would be real appreciated.
Several times I have gotten "Warning: Unable to change GSM/UMTS Band, Please try again later."
Click to expand...
Click to collapse
OK is it possible for this to be tower related? What I mean is I drove about 4 miles from my house, got a better signal and surfed the internet using HSDPA. Now I'm back home and HSDPA is chocking and giving me "unknown error 0x80072f78"
What He!!?
One note on my HSDPA trouble, it must some how be related to the one tower nearest my home. When I go anywhere outside a 5 miles radius (I live near the tower) everything works fine.
Here is the weird part, every where else the phone will switch from HSDPA to 3G to Edge and back no problem. Here in town it locks into HSDPA and refuses to switch to 3G or anything else. I don't know if it means anything but it seems to get an IP address I can ping but I don't get any DNS info!.
Now how can I convince AT&T that there's a problem when their support person denies there is any HSDPA services and I should only expect 3G?
hello,
after searching on "3G" in the forum, i seems that the problems are just the opposite to my question, they all want 3G to be turned off.
Now I want to connect to 3G (with the "G" icon on the staus bar).
My problem is that it always connect on "edge", with the "E" icon in status bar and when I want to make a video call, it always says that there is no connection to 3G so I can't make videocall.
Anyone knwos how to activate 3G?
I looked into the connections, but I don't want to mess in it without knowing what I do.
BTW I'm in Europe (Belgium).
Thanks
You fell into the same trap I did when I first got a Windows Mobile phone.
G means GPRS and is the lowest, simplest connection speed.
G = GPRS. "Normal" internet speed (9.6-14.4kbps)
E - Edge. "Enhanced" internet speed (normally 48kbps, but can be higher)
3G = 3G internet speed (128-384kbps). Also allows video calls.
H = HSDPA. "Mobile broadband" speed. (1.8Mbps, 3.6Mbps or 7.2Mbps depending on operator).
You'll want to go to:
Start > Settings > Connections > Advanced Network
Make sure that HSDPA/HSUPA is enabled
From then on, it depends on the signal in your area. If you find that you're having a problem getting and maintaining a 3G or H signal, you might need to get an updated SIM from your operator. I got a new SIM from O2-UK and it solved my connection problems immediately.
I see that HSDPA/HSUPA is enabled.
Could it have something to do with the settings in connections (instead of advanced network settings)?
I will also check with my provider (sim card)
Thanks for the reply
i cannot connect to the internet not using wifi. i do however h an H symbol next to my signal. i dont get why i have the hsdpa but cannot connect. i've tried anything i can think of.
*i can't turn data connection on in my comm manager, it automatically disconnects and says wap.cingular not working or gprs not working somthing like that.
*in the connection settings i pick media net wich is automatically picks att but still won't
*in settings/personal/phone i left if auto defualts for bands
*settings/connections/advance network i even tried to put it to hsda ONLY won't work
the only new lead im getting is this Zenith post saying he got new sim card so now it's working. that's all im getting at now. but im even skeptical about that
If you are not getting the 3G or H icon then you either have no coverage or an incompatible SIM.
If you can't connect to the internet you either have incorrect settings on your phone, or your network aren't allowing you on their APN.
Suggest in all cases phoning your network to get clarification.
artesea said:
If you are not getting the 3G or H icon then you either have no coverage or an incompatible SIM.
If you can't connect to the internet you either have incorrect settings on your phone, or your network aren't allowing you on their APN.
Suggest in all cases phoning your network to get clarification.
Click to expand...
Click to collapse
you wouldn't believe how i found out i had no internet. they say'd it was in the system but it was disabled in thier system. i put in my brothers sims and his work just fine. so i told them to look at whatever his plan is and they switch to what he had. anyways long story short i found out not my settings bc you just auto configure it connectin wizards, and wasn't sims card, it was stupid att. i was getting the H icon but not an H on my signal. anyways its all done now. thanks again guys
Today i flashed my HTC Touch HD with this rom (STONEHENDGE), Now for some reason i cannot get my 3 network to work atal.. Cannot make or recieve calls. It shows an exclimation mark next to the network signal icon. Also when i press find network in network selection it only finds o2 tmobile orange and vodaphone.
Any help? Is it maybe the radio needs updating?
Might sound obvious, but you have checked the UMTS band is 2100 (or Auto), and the phone has 3G enabled in comms manager?
If it's finding the 2G networks but not Three, sounds like phone is set to GSM only, sometimes happens ater a new ROM.
Hi Everyone,
I'm usually just a reader on XDA, but I have found a problem that appears not to have been solved and wondered if anyone had any insight.
Problem Summary
When in an area (or network) with only HSPA and UMTS (strong HSPA/UMTS signal, but with no LTE or 2G available), the phone will drop from H+ to 3G erratically, always dropping the data connection. Traditional phone calls are not affected.
Detailed Description
I have a OnePlus Two and have 2 SIM cards. My first SIM Card is with Bell Canada (Virgin), and the second SIM Card is with WIND Mobile Canada.
Neither Bell nor WIND operate a 2G network, so the lowest the service can fall to is UMTS/3G.
Initially, I didn't notice the problem because Bell also operates an LTE network, and there is no problem with dropping the data connections when on LTE.
When I switched to the WIND SIM card (which only operates HSPA and UMTS), I noticed a problem where the phone would initially connect to H+, begin downloading whatever is needed (say, streaming music), but then part way through the download, the connection would switch to 3G, and the data would effectively stop. Within a minute, the service would jump back to H+ and download some more, but this cycle would continue (H+ --> 3G --> H+ --> 3G... ), with no way of knowing 1) how long the H+ connection would last before dropping to 3G (usually less than 30 seconds), and 2) after dropping to 3G, how long before going back to H+. This problem makes the phone almost useless when there is no LTE.
The most obvious troubleshooting I did was move to locations of better signal but I quickly ruled that out, as nothing seems to remove this problem. Other things I tried was to: move locations in the city, reboot phone, hard reset phone, flash most updated version of Oxygen, unlock bootloader, root, try the HSPA Keepalive app, swap SIM1 to SIM2, and many other things.
I originally thought this was a network issue, but I put this WIND SIM in another phone and there was no problem in any way that resembled this problem.
I also ruled out this being a network-specific problem, as I have taken a trip with the Bell SIM to an area where Bell does not have any LTE coverage (only HSPA and UMTS) and the same problem occurs on Bell as with the WIND SIM.
I have found people who had this problem on the OnePlus One tend to recommend using 2G to stabilize the connection, but this is not possible on Bell or WIND. That solution also would not provide adequate data speeds.
Remember this problem only affects data connectivity, as 3G traditional phone calls have no problems.
Question
Does anyone know if there is a way to adjust the conditions when the OnePlus Two will choose to switch from H+ to 3G?
Does anyone have any easier suggestions?
Thank you all in advance, because this rendering this phone almost useless when there is no LTE coverage.
I believe your problem is that phone it's dualsim standby, that means only one modem that alternates signal for both sims, I think normal would be alternating from faster network to slower network on sim without data.
Having to change to g3 between sims theres something stoped in the modem and data connection is also stopped.
You have no problem with voice calls because other sim is automatically turned off and unreachable.
There's nothing you can do if you're forced to only 3g on both sims
By 3g I mean 3g or h+ which to my knowledge are the same
Hope I was helpful and not wrong or more confusing
Sent from my ONE A2005 using Tapatalk
fburgos said:
I believe your problem is that phone it's dualsim standby, that means only one modem that alternates signal for both sims, I think normal would be alternating from faster network to slower network on sim without data.
Having to change to g3 between sims theres something stoped in the modem and data connection is also stopped.
You have no problem with voice calls because other sim is automatically turned off and unreachable.
There's nothing you can do if you're forced to only 3g on both sims
By 3g I mean 3g or h+ which to my knowledge are the same
Hope I was helpful and not wrong or more confusing
Sent from my ONE A2005 using Tapatalk
Click to expand...
Click to collapse
Thanks, I will try disabling the second SIM to see if there is a bug with the dual-sim...
What it currently does with the second SIM is it either shows "R" for roaming or just emergency only, but perhaps there is a software issue so I'll see if disabling the second SIM makes a difference.
biomedeng said:
Thanks, I will try disabling the second SIM to see if there is a bug with the dual-sim...
What it currently does with the second SIM is it either shows "R" for roaming or just emergency only, but perhaps there is a software issue so I'll see if disabling the second SIM makes a difference.
Click to expand...
Click to collapse
Though strange, this workaround fixes the issue. Thank you to fburgos for the suggestion!
So just in case anyone ever finds this issue creeps up on them, the solution is to DISABLE the SIM you are not using. It's not the most convenient workaround to swap SIMs, but the other SIM will be in Emergency Mode, so it really makes no functional difference.
On the technical side, it does appear that there is actually a bug in Android for a very uncommon network configuration. It will only appear in this exact configuration:
SIM1: Network has HSPA/3G only, no LTE or 2G to move to
SIM2: Network also only has HSPA/3G with no LTE or 2G
The non-data SIM does NOT connect to a roaming network (connects with "Emergency Only") - if it connects to a roaming 2G network, this problem does not happen.
The data SIM connects to HSPA/3G
Both SIMs are active
I'm not sure if this will happen anywhere else in the world other than having a WIND Mobile Canada SIM and Bell or TELUS Canada SIM
If anyone has insight on how to report this to Google, or someone else who can confirm my theory, that would be great!
Try this:
1. You need to make sure you have the correct LTE APN selected in mobile networks and LTE as preferred type.
2. Go to dialer and type in this: *#*#4636#*#*
3. Phone Information
4. Set Preferred Network Type to: LTE/GSM (PRL) - you an play with which one you wanna use but the one I said works for sure. on other roms I have" TD-SCDMA, GSM/WCDMA and LTE"
5. Now click TURN OFF RADIO and wait WAIT few secs. will that button turns to Turn Radio ON
6. Now TURN ON RADIO and wait
7. when u see the triangle for the signal is back, at least black , go down and lick SMSC REFRESH then UPDATE.
8. now just go back to APN settings and go into your LTE APN
9. Change Bearer to LTE
biomedeng said:
Hi Everyone,
I'm usually just a reader on XDA, but I have found a problem that appears not to have been solved and wondered if anyone had any insight.
Problem Summary
When in an area (or network) with only HSPA and UMTS (strong HSPA/UMTS signal, but with no LTE or 2G available), the phone will drop from H+ to 3G erratically, always dropping the data connection. Traditional phone calls are not affected.
Detailed Description
I have a OnePlus Two and have 2 SIM cards. My first SIM Card is with Bell Canada (Virgin), and the second SIM Card is with WIND Mobile Canada.
Neither Bell nor WIND operate a 2G network, so the lowest the service can fall to is UMTS/3G.
Initially, I didn't notice the problem because Bell also operates an LTE network, and there is no problem with dropping the data connections when on LTE.
When I switched to the WIND SIM card (which only operates HSPA and UMTS), I noticed a problem where the phone would initially connect to H+, begin downloading whatever is needed (say, streaming music), but then part way through the download, the connection would switch to 3G, and the data would effectively stop. Within a minute, the service would jump back to H+ and download some more, but this cycle would continue (H+ --> 3G --> H+ --> 3G... ), with no way of knowing 1) how long the H+ connection would last before dropping to 3G (usually less than 30 seconds), and 2) after dropping to 3G, how long before going back to H+. This problem makes the phone almost useless when there is no LTE.
The most obvious troubleshooting I did was move to locations of better signal but I quickly ruled that out, as nothing seems to remove this problem. Other things I tried was to: move locations in the city, reboot phone, hard reset phone, flash most updated version of Oxygen, unlock bootloader, root, try the HSPA Keepalive app, swap SIM1 to SIM2, and many other things.
I originally thought this was a network issue, but I put this WIND SIM in another phone and there was no problem in any way that resembled this problem.
I also ruled out this being a network-specific problem, as I have taken a trip with the Bell SIM to an area where Bell does not have any LTE coverage (only HSPA and UMTS) and the same problem occurs on Bell as with the WIND SIM.
I have found people who had this problem on the OnePlus One tend to recommend using 2G to stabilize the connection, but this is not possible on Bell or WIND. That solution also would not provide adequate data speeds.
Remember this problem only affects data connectivity, as 3G traditional phone calls have no problems.
Question
Does anyone know if there is a way to adjust the conditions when the OnePlus Two will choose to switch from H+ to 3G?
Does anyone have any easier suggestions?
Thank you all in advance, because this rendering this phone almost useless when there is no LTE coverage.
Click to expand...
Click to collapse
I have the same problem. Do you already have solved it?
I use only one SIM card so it is not a problem two cards.
really you do not have this problem? if no one knows the solution?
compared with my htc butterfly 2 and another low-end android, one plus 2 running latest Oxygen OS has serious connectivity issues. I compared the signals strength using same sim card in same location (including being connected to the same tower) and One Plus 2 keeps dropping the connection and has really poor signal strength. I have tried the *#*#4636#*#* and tried different network modes, but none of them are helping. Its a real disappointment that the basic feature of this phone is screwed up.
I have tried with CM13 as well. Any ideas if this is a modem version issue?
odeccacccp said:
Try this:
1. You need to make sure you have the correct LTE APN selected in mobile networks and LTE as preferred type.
2. Go to dialer and type in this: *#*#4636#*#*
3. Phone Information
4. Set Preferred Network Type to: LTE/GSM (PRL) - you an play with which one you wanna use but the one I said works for sure. on other roms I have" TD-SCDMA, GSM/WCDMA and LTE"
5. Now click TURN OFF RADIO and wait WAIT few secs. will that button turns to Turn Radio ON
6. Now TURN ON RADIO and wait
7. when u see the triangle for the signal is back, at least black , go down and lick SMSC REFRESH then UPDATE.
8. now just go back to APN settings and go into your LTE APN
9. Change Bearer to LTE
Click to expand...
Click to collapse
Did It.. But it seems like it didn't solve my problem..