i updated my phone from 4.0.4 to the latest update.
it was doing great. but after the update was done, my phone shut down.
and now it wont power on.
it was on the charger for over an hour, and still didnt work.
tried to boot into recovery..didn't work
fastboot..didn'd work.
all it does:
when the charger is connected. it shows a green light.
when i try a softreset(volume down- and power key for 120 sec) the green light flashes.
What should i do?
Are you using an OEM Motorola charger? The green light usually indicates the battery is to dead to power up and it detects that it is connect to a power source... I would ensure a proper connection and use a OEM Motorola charger, allow it 8-10 hours for the battery to regain sufficient charge to power on... In the event it does not it may be a software issue not allowing it to charge in that case you can either purchase a factory cable/team black hat adaptor or make your own(not recommended with out basic electrical knowledge)
Edit... Well totally stopped mid sentence didn't I... With the factory cable/team black hat adaptor you should be able to boot to fast boot and use rsd lite to flash the stock firmware..
We cannot teach people anything; we can only help them discover it within themselves.
i was using an 3meter cable i bought somewhere.
ill try it with the OEM cable, lets hope that was the issue :s
Are you sure the update was complete, or is it possible your battery died during the update?
Sent from my HTC6525LVW using Tapatalk
now i think about it... i gues that happened ":l
You may be in a rough spot if that happen... You can try a factory cable to try and boot it to fastboot.. I was thinking that happen but didn't want to be a pessimist...
We cannot teach people anything; we can only help them discover it within themselves.
ezknives said:
You may be in a rough spot if that happen... You can try a factory cable to try and boot it to fastboot.. I was thinking that happen but didn't want to be a pessimist...
We cannot teach people anything; we can only help them discover it within themselves.
Click to expand...
Click to collapse
it has been charging with the OEM cable for 10 hours now, still no life in my phone, just a greed led popping up sometime random i gues?
USB
i found something maybe somewhat useful D: :crying:
when i do connect it to my laptop the green light goes flashing very slow.
every time the green light is on(3 sec), my pc(windows) says it is connected as a USB-Device
and when the green light is off(3 sec), the device is disconnected.
and it plays the connected/disconnected sound everytime.
Has it ever been rooted or boot loader unlocked?
We cannot teach people anything; we can only help them discover it within themselves.
ezknives said:
Has it ever been rooted or boot loader unlocked?
We cannot teach people anything; we can only help them discover it within themselves.
Click to expand...
Click to collapse
rooted for a looooooooong time.
unlocked bootloader.
was running CM11 for a long time. but my data(LTE) wasnt working.
so i used RSDlite to get it back to stock.
things worked out great.
used it for a couple a days
battery was around 25%
saw i had an android update.
downloaden en updated the phone while i was making dinner, so i wasn't realy looking at my phone when it was updating.
I was gonna suggest try your chances at the warranty from Motorola but that's out the window... Have you had any luck getting this running? You try a factory cable?
We cannot teach people anything; we can only help them discover it within themselves.
Fwiw If you have a Samsung branded cable it has the line needed to create a factory cable... You short pins 1 and 4 on the micro side.... I posted a short tutorial on this on the kfhd forums...
Sent from my XT907 using XDA Free mobile app
---------- Post added at 03:22 PM ---------- Previous post was at 03:19 PM ----------
Found it..
http://forum.xda-developers.com/showthread.php?p=39569189
Sent from my XT907 using XDA Free mobile app
Related
Please read all of the first post above and then all the instructions FIRST, before trying anything. If you are unsure about anything PLEASE ASK QUESTIONS. No one wants you to damage your phone. So make sure you understand what your doing. If your not sure what your doing you could do more damage to the phone And remember with an unlocked bootloader you can do severe damage.ATTENTION: If your phone is not working but you see a led or have bootloops DO NOT USE HARD-RESET. This can make your phone lock/freeze up until the battery dies. It took 51 hours for mine to die.
However if you get stuck on a boot screen or get bootloops a SOFT-RESET may work to reboot.
If you have unlocked your bootloader this guide may or may not work for you. If you have trouble recovering then see the "TRICKS that require FASTBOOT-mode" below.
YOU NEED TO RESET YOUR PHONE!
If your phone is soft-brick and does nothing when, -the buttons are pressed, -a charger is plugged in, -or if the screen is still ON then....
The memory chips need lose power to clear the bad data and reset the phone. Either by the battery going dead or by unplugging the battery.
You can to leave the phone on a charger to see when the battery dies. Usually the battery will not charge in a soft-brick state and will die while still plugged in. After the reset you should then get the red led. However if you get a red led immediately when first plugged in and no response but red led for a long time, then you may need to leave the phone unplugged and let the battery die.
Only after the chips reset will you get the red led. The RED LED should mean the phone is charging in 'low battery level charge mode'.
Once you get the red led, after the reset, do NOT try to turn on the phone. If you try to start the phone now without fixing the problem you will have to start all over.
UNPLUGGING THE BATTERY
If you feel like taking your phone apart you can unplug the battery. Most 2012 XPERIA's have a built in battery that is not designed to be easily removed. However next to the battery there should be a ribbon cable with a plug to the mother board. Unplugging this cable for 2-3 minutes should reset your phone without letting the battery die. Read here for the original idea post
CAUTION: this may effect your warranty
CLICK This for a Picture
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The Rubber Band Trick
Here are some links to help describe the rubber band trick.
http://forum.xda-developers.com/showpost.php?p=37562298&postcount=301
http://forum.xda-developers.com/showpost.php?p=37844592&postcount=317
http://forum.xda-developers.com/showpost.php?p=39835850&postcount=527
Now after the phone has reset and you have the red led.~ keep charging with wall charger. A charger has a higher current rate and should charge faster than a PC.
~ Make flashtool ready to flash your stock.ftf file. If you are experiencing errors while flashing the entire ROM try to flash just the kernel, check off all in the exclude box except kernel. At this point your battery is very low and doing this will make the flash process much faster than trying to flash the entire ROM.
~ Try to connect phone in flash-mode. If your phone has enough battery you will get green led. If the flash fails on the first try, just put it back on the charger and wait about 10-30 minutes and repeat. It may take a while to charge enough to flash.
~ If you see the red led go out, then try for flash-mode.
~ If you get bootloops, try to flash between loops. As soon as you notice loop, hold volume down and plug the phone into PC with FlashTool ready. Once the loop starts you have very little time to flash, before the loops drain the battery. If you can not flash, the battery will have to die and phone reset. Then start over with red led.
~ After you complete the flash, unplug the phone and see what happens. Sometimes it will boot to Sony screen and then shut off by itself, if so plug in to a charger. You should get the red led then the battery charging screen then. After about 20 minutes of red led.
~ If you get a green led (for flash mode) then press the power button until 1 vibration. The green led should flash 1 time. This will end flashmode and start the phone. If you don't end flashmode the phone will still give a green led whenever plugged in, but it will not charge, until the battery dies and the phone resets again.
~ If you were able to flash the entire stock.ftf file and your phone has gone from red led to the charging screen, then your phone should now be recovered and turn on normally.
~ If you could only flash the kernel then you will get bootloops. Again you can unplug and try a hard-reset to turn off the phone. If hard-reset works plug in charger and wait for red led and then charging screen.
~ If you don't do a hard-reset, the phone boot looping should kill the battery and then plug in charger (this is what I did). Then wait for red led and then charging screen.
~ Now you should have a good kernel and the phone plugged in. You should have the charging screen with the battery icon and led for 'off-line charge mode'. Charge until over 50%. A quick press of the power button will bring up the charging screen.
~ Once over 50% then flash the full stock.ftf with a full wipe.
~ If you got this far but still cannot flash a full stock.ftf file then try to use PC Companion software to REPAIR your phone. Make sure battery is more than 50%.
~ If all fails then post a copy of the FlashTool log in this thread.
To save space please use the BB code for HIDE. Example
[HIDE]The text from your log here[/HIDE]
The text from your log here
If the above steps do not work you can also try the tricks below.
Due to the amount and length of TRICKS, I have provided links to their post
TRICK: FOR PHONE THAT WONT RESPOND; {VIEW THIS POST FOR TRICK}; Confirmed working on ION
TRICK: FOR PHONE THAT WONT RESPOND; {VIEW THIS POST FOR TRICK}; Confirmed ION
TRICK: TRY CONNECTING TO PC; {VIEW THIS POST FOR TRICK}
TRICK: IF BOOTLOOPS WHEN PULGGED INTO PC; {VIEW THIS POST FOR TRICK} This should also work for FLASH mode; Confirmed ION
TRICK: FOR PHONE THAT WONT RESPOND; {VIEW THIS POST FOR TRICK}; Confirmed working on Xperia J
These TRICKS require FASTBOOT access on the phone
TRICK: FOR KERNEL WITHOUT OFFLINE CHARGING; {VIEW THIS POST FOR TRICK }
TRICK: IF YOU GET INTO FASTBOOT MODE, BLUE LED; {VIEW THIS POST FOR TRICK}; Confirmed ION
TRICK: FOR UNLOCKED BOOTLOADERS; {VIEW THIS POST FOR TRICK}; Confirmed ION
TRICK: IF YOU TRIED A HARD RESET (3 vibrations); {VIEW THIS POST FOR TRICK}
TRICK: TO USE FASTBOOT TO ACCESS FLASHMODE; { VIEW THIS POST FOR TRICK}; Comfirmed S
TRICK: USE FASTBOOT TO FLASH KERNEL; {VIEW THIS POST FOR TRICK}; Confirmed ION
TRICK: FOR UNLOCKED BOOTLOADERS; {VIEW THIS POST FOR TRICK}; Confirmed SOLA
Please give feedback if any of these work and on what devices, I will update. 272
If you think I should add something new, either post it or PM me the content to add. Thanks to all those who help.
Please vote in my POLL. If this thread helped you please guide others here for the same help
LINK FOR FLASHTOOL HELP POST
List of those that have recovered
RaWrGs said:
thank you! Worked perfect!! as hard as it was to let the battery die I did it and she worked!!!
Click to expand...
Click to collapse
305nole said:
My phone is working again, you just have to be patient, as it took >16 hrs for my phone to turn on. Once my phone turn on automatically, I had let sit for 4hrs, then pressed the power and volume up buttons at the same time and held it for exactly 5 seconds, it then turned off and I was able to flash as normal. Just be patient. Thanks everybody.
Click to expand...
Click to collapse
accts said:
Here are the steps I took successfully revise my phone from soft brick.
[*]That is all ... Back and running.
[/LIST]
GOOD Luck.
Timing = could be different from phone to phone - depends on battery of the phone before it dead.
Sent from my HTC PH39100 using Tapatalk 2
Click to expand...
Click to collapse
accts said:
Unbelievable - SOFT brick again :crying: ... trying to deodex the new fw 6.1.E.2.68. Now my device is unresponsive neither to soft or hard reset. Waiting for the phone battery to die and see if I can do anything after that
Edit: whewww...So glad just had to wait for battery die - recharge ! was able to reflash - back in business again :victory:
Click to expand...
Click to collapse
faiisfaizal said:
i charge it then got bootloop...but i did not manage to go to flashmode but fastboot....so i just flash cm9 kernel and it boot..then it go back off....i charge it again and its turning on so i just manage to go flashmode so i flash stock ...and now its revive...im glad i made it
dont just w8 it to green....when it bootloop just do the button to go to flashmode...dont do hard reset..it make ur phone longer charging to make the red led coming
Click to expand...
Click to collapse
soudara said:
ok flashtool flash complete very hard to get greenled but its ok but no boot , i replug in wall charger for 10mn and auto boot and all is ok
my ion working perfect
thank you all
i use generic honkong tft firmware LT28i_6.1.E.1.19_Hong Kong.zip
Click to expand...
Click to collapse
ching11 said:
yeah, finally, Successful to flash the rom in my ION and running normal now~~~:victory::laugh:
Click to expand...
Click to collapse
ghekua said:
I just get my phone back to life )
My phone back to life now.
Click to expand...
Click to collapse
markelON said:
I Flashed Custom kernel and got Briked (Boot Loops) at 9th Dec Morning 10:30AM
Did Hard Reset and phewwww Phone is Completely Dead Unresponsive.
BUT DON'T GIVE UP....
Many Thanks To People Who Have Shared Their Experiences Here.. Keep It Up Guyz.:good:
Click to expand...
Click to collapse
aimakun said:
In last Thursday I decide to get back my bricked ION and then follow the instruction as markelON suggested.
And when I tried 2 hours later, I've finally get the Xperia logo again, and everything become working!
In my case I found later that the speaker in back of the phone has broken. I don't sure this was already broken since the phone bricked or between the repair service tries for recover my phone. But other functions are working and my dad had car accident recently. So I keep my phone and still not send back to repair service yet.
Now it has hardware issue, not brick, so I could call the repair service to fix it now. :silly:
I thank everyone who lend the help, especially markeION.
Thank you very much.
P.S. I has also written the fix instruction summary in my language and publish to local community too, based on markeION suggustion. So I think this would help others who aren't skill the English language too.
Click to expand...
Click to collapse
Zirdark said:
Thanks!
I was able to get it in fastboot mode, i will now try to fla****
this is what i did for the people having the same issue.
once you get the boot loop press power+vol up until you get first vibration, after that very quickly you need to plug usb to the pc while holding only the vol up key.
this worked in a xperia ion bootloader unlocked
Thanks everyone for your help. i got more experience now, i hope this helps to everyone else that have or get the same issue.
Remember when you get bootloop press power+vol up until you get first vibration, then very quickly connect the phone pressing vol up or vol down to get fastboot or flashmode, then you can fix the phone with flashtool. this worked for my Xperia Ion bootloader unlocked
Click to expand...
Click to collapse
warfist said:
Look, right now i am in Fastboot Mode! This time it worked again. But when i try to flash a kernel.sin it says that there is no device! What to do man??
EDIT: WAIT, NOW I AM IN FLASH MODE AND TRYING TO FLASH KERNEL! But after a few seconds i get this:
EDIT 3: I made it! I had to flash the whole Rom. Not just the system.sin and kernel.sin. THANKS FOR ALL YOUR HELP!
Click to expand...
Click to collapse
JaneKimC said:
So I don't do anything about the purple led and just redo the steps?
Okay o_o
-edit-
whathe
I GOT IT TO FLASHMODE
After charging and having constant red led to no led (?) I unplugged from the wall charger and and then plugged to laptop to wait for bootloop. So there was red led, then after a while no led again. I just pressed down (didn't expect anything to happen lol) and then I got GREEN LED!!!! Luckily, I already set up flash tool
I installed ALL the drivers in flash tool
But there was no Ion,
right now i'm installing pc suite cause my sister said there are drivers there.
Am I doing the right move? O_O
-edit2-
MY SISTER WAS RIGHT
IT FLASHED ALL THE WAY THROUGH!!!
btw, checked Exclude TA, is that correct?
phone still won't boot (assuming no battery)
I'M CHARGING RIGHT NOW!!
will report back when it boots
sorry for page stretching!
-edit3-
HOMYGOSH I LOVE YOU ALL
THANKS SO MUCH GUYS!
HAPPY NEW YEAR!
EVERYTHING PAID OFF!!
THANKS TO EVERYONE WHO HELPED ME!!!!
SAVED ME A LOT OF $$$ ^_^
Click to expand...
Click to collapse
tempest2112 said:
Many thanks for this post as I was stuck in a ram dump boot loop and following the instructions allowed me to flash a ftf file and now the phone (Sony Miro) is up and running :victory:
Click to expand...
Click to collapse
albuah said:
i manage to get bootloop after 5-10 minutes.
got my kernel on back. tapping the sony logo and enter cwm , restore my backup , and reboot...but the phone not reboot.
screen are black and red led still there. usb still attach to pc.
need to recharge batteries to full/green led ?
update : i remove the usb cable , and use fastboot mode to flash kernel and on the phone. it boot up nicely in my miui backup with 1% battery haha...
thx to all that help me and of course to this thread
Click to expand...
Click to collapse
ganeshbiyer said:
The phone is back.
Sent from my LT28i using xda premium
Click to expand...
Click to collapse
txingu said:
Thanks ToledoJab!!
I can repair one xperia s with a format memory problem.
The phone stay in SONY logo everytime, but I can flash it again.
Thanks!!
Click to expand...
Click to collapse
Damjan94 said:
Thanks you rly helped me get my phone working again
I got it bricked by installing cwm and it didn't let me boot in os, than I formatted /system and lost cwm, all my system
I wonted to install newest cynogen mod so my question is: "can I use flasher to flash cynogen mod?"
Click to expand...
Click to collapse
dansdepeter said:
After all, I read about unbricking phone I am now in the situation of blinking red light and the phone turn on with a black screen.. then after 20min the phone fully turn-off and i charge the phone and i get solid red light.. hoping that it will be fix. Thanks to all
My Xperia ion now back to normal.. I get red light but cannot detect on laptop and all the button of xperia not working. I first run the flashtool ready to install firmware and then together with pc companion and finally the xperia green led comes up........ w/out pc companion my xperia still on red light and all button of xperia not working.. The Flashtool detect the phone and install the firmware...
Thanks to this blog..
Click to expand...
Click to collapse
gegode said:
:victory: :good: well thanks to all xda developer for this thread.. :good: :victory:
my 1 week old Sony Xperia J (rooted , v6 supercharger , stock firmware) that appears BOOTLOOP :crying:
it happens when i try to use some method "how to connect stock firmware ICS to ad-hoc" by changing wifi supplicant script..
OK ,
:silly:ENJOY UR BRAND NEW/OLD ware:silly:
:victory: WELL THATS IT ,, THATS WHAT I'VE DONE ,, you guys can follow it if you like .. i can do it , so u can. ryt? :silly:
THANKS TO THIS THREAD , AND ALL CREDIT TO ALL XDA Developer Who already tested all trick and method and provide all TOOLS :highfive:
IM NOT GOOD ENOUGH IN ENGLISH . PERIOD
Click to expand...
Click to collapse
crevatsch said:
Thanks for the answer and the miracle has happened, my phone is back from the dead. This is how i did it:
I got frustrated with the phone after it wouldn't respond to the soft reset it was trying (power + volume up). Then i pressed the volume up button while playing a game with the other while in the corner of my eye i see the light changing color and yes, it had gone into fastboot. After that i flashed the kernel only, but the phone wouldn't boot. I was angry that i let this good chance slip, but i managed to do the trick again: just keep pressing volume up, until it went into fastboot. I flashed the stock rom and my phone worked again.
Moral of the story (and something to put in the startpost): Even if the screen doesn't show anything and even if the phone doesn't vibrate or give a signal to indicate the battery is full it can still go into fastboot if you press the button repeatedly and keep trying.
Thanks for the help!
Click to expand...
Click to collapse
CoB_Mike said:
Worked like a charm for me brother. Installed something to my L28at and it was showing incorrect battery and couldnt re install original OS. Now I am good!
Click to expand...
Click to collapse
snaky47 said:
Anyone can help me please, i have strong red light and i can't flash again.
EDIT: Now, after unplugged and waiting 5 mn, i plugged again I see the logo of the battery:laugh: and it appears that it is empty after 20 hours of charging lol. I wait a bit and I'll let you know if I can flash:fingers-crossed:
EDIT2: I installed cm9 and restored my backup. everything is ok now.
Click to expand...
Click to collapse
gnahanut said:
Mine is the same problem, the kernel does not support offline charging, and the issue is that: the phone runs out of battery - It gets booted up after 5 minutes charging and then turn off. The cycle continues.
I solve the problem by:
- Let it charge till the screen boots up.
- Power + volume up for 1 vibration, and then hold volume up for fastboot mode.
- Flash adv kernel 17 and then connect to charger. Let it charge for 30 mins.
- Reflash the Rom kernel.
Everything works perfectly after that.
Click to expand...
Click to collapse
Flowa said:
Thanks it worked!
But is there a way that you can use the phone with pc companion after flashing it?
Because pc companion told me i have a wrong firmware...
Click to expand...
Click to collapse
anzsensei said:
Alhamdulillah ~ SUCCESS :good:
SUPER Thanks To Everyone Here~!!
:victory:
Click to expand...
Click to collapse
ardalaan said:
ok i after about 9 hours of charging i didn't get any response from my Phone (ion)
so i decided to open my phone and disconnect the battery cable !
after i disconnect my battery cable and plug it again i connect my phone to wall charger and get a red light LED.. after about 20 minutes red led become orange then i connect my phone to pc and start flashtool and flashed new TFT file
all i am saying is that if u don't get red light after couple of hour you have 2 options !
let the battery drain then start charging or unplug battery cable then plug it back
here is the picture of my ion's battery flat
Click to expand...
Click to collapse
Levopron said:
Yess!! I Repair.. Thank Youu!!
Click to expand...
Click to collapse
ToledoJab said:
Well I recovered my Ion.
Now for some reason I cannot flash any baseband when using win xp. I can flash basebands from ubuntu though. It took me a few hours to figure this out. Tried reboot, older version and every stock ftf I have, ics & gb. I can flash all other parts of the stock ftf. Baseband freezes flashtool up at processing the data and I have to close flashtool.
Not sure why win xp wont work, but since linux worked I dont care
I got some good tips to add to OP.
Flashing just the kernel requires less battery charge to flash and fixes offline charging.
Also unplugging the battery after back pieces are removed should eliminate the waiting for battery to die, if you can handle taking phone apart. Battery unplug should save a lot of time in both discharge and charging. If battery is full if will take days to discharge. But if you unplug it should reset and keep the charge for flashing.
Well now on to my wifes captivate glide. It keeps shutting down when data is turned on. Time to learn about odin and Samsung
Click to expand...
Click to collapse
[SOFT-BRICK RECOVERY] Recover most XPERIAs from SOFT-BRICK
If you are not sure what your doing or just want to confirm something, PLEASE ASK QUESTIONS FIRST. You always want to do the easiest things first.There many of us that have had success using different methods. And there are many of us who are willing to help.
The Wikipedia definition for {Brick (electronics)}
When used in reference to consumer electronics, a "brick" describes an electronic device such as a smart phone, game console, router, or tablet computer that owing to a serious misconfiguration, corrupted firmware or a hardware problem, can no longer function. The term derives from the vaguely cuboid shape of many electronic devices (and their detachable power supplies) and the suggestion that the device can only function as a large, heavy object.
The term can also be used as a verb. For example, "I bricked my MP3 player when I tried to modify its firmware."[1]
In one common sense of the term, "bricking" suggests that the damage, often a misconfiguration of essential on-board software, is so serious as to have rendered the device permanently unusable.
However, another use of the term "bricked" is understood to describe a situation where a device is unable to function even when the device does have potential to be recovered later to a working state. In this sense, the damage may be reversible; it is only during the period that it's unable to function that the device is deemed "bricked". This is often referred to as a "soft brick" whereas an unrecoverable device is a "hard brick".
DON'T WORRY, BE PATIENT, YOU CAN FIX YOUR PHONE.
This common 'cents' is worth more than a million dollars the price of your phone
accts said:
My two cents, always install CWM - Backup your ROM, before doing any modding to your phone.
Click to expand...
Click to collapse
For this guide I will define types of RESETS that happen when pressing both the POWER and VOLUME UP buttons.SOFT RESET = 1 vibration then let go of buttons (hold about 3 seconds); Like hitting REBOOT.
HARD RESET = 3 vibrations then let go (about 10 seconds); Like taking out the battery.*
*USE HARD RESET ONLY IF ALL OTHER TRICKS HAVE FAILED. RECOVERY FROM THIS DEEP LEVEL OF SOFT-BRICK WILL TAKE A LONG TIMEBoth can be used at anytime on a working phone. Most bootloops will also allow resets
XPERIA phones have 2 different modes that are used in recovering from SOFT-brick. FLASH mode & FASTBOOT mode.FLASH mode, is used by FLASHTOOL and can be used on every model of XPERIA phone with a locked or unlocked bootloader. FLASH mode will give a soild GREEN notification led when connected. To connect in FLASH mode:
Start with the phone turned off (or in between loops for some tricks)
Press and HOLD the volume DOWN button. (don't let go )
Now connect to a PC using USB
If all went correctly you will get GREEN led, then let go of button
FASTBOOT mode is used by Android Debug Bridge (ADB), and is found on every Android device. FLASHTOOL also uses FASTBOOT mode, however to flash this way you need an UNLOCKED bootloader. NOT EVERY PHONE CAN USE FASTBOOT. To find out if you can use FASTBOOT and how to set it up read {Spectre51's} thread on {unlocking & relocking bootloaders}. FASTBOOT mode will give a soild BLUE notification led when connected. To connect in FASTBOOT mode:
Start with the phone turned off (or in between loops for some tricks)
Press and HOLD volume UP button. (don't let go )
Now connect to a PC using USB
If all went correctly you will get BLUE led, then let go of button
To recover your phone you need to have FLASHTOOL ready and waiting at a specific spot.
If you need help with setting up & using FLASHTOOL {>>CLICK HERE<<}
DO NOT CONNTECT YOUR PHONE
First you need to have FLASHTOOL installed from {HERE}
Now run FLASHTOOL.
From FLASHTOOL home, select the flash/lightning bolt button
Select FLASH MODE
Select your stock firmware file
WIPE: everything
If available EXCLUDE: TA. (this option is not available for all stock.ftf files, if it's there just exclude it)
Now click START button
After FLASHTOOL prepares files, you should get this screen (or similar depending on version of FLASHTOOL)
>>>>>STOP<<<<< FLASHTOOL is now ready for TRICKS
For help with finding your phones STOCK.ftf file click here
You can use the file for your XPERIA model below to recover from SOFT-brick.
To make your models specific .ftf file after you recover, you will find instructions {IN THIS POST}
MAKE SURE YOU USE A STOCK FIRMWARE FOR YOUR MODEL XPERIA. Each phone model has a different file. Using the wrong file will give you the very SOFT-brick your trying to fix. If your not sure then ask for help.
Links to STOCK FIRMWARES
XPERIA P{LT22}
XPERIA V{LT25}
XPERIA S{LT26}
XPERIA SL{LT26ii}
XPERIA Acro S{LT26W}
XPERIA ION{LT28}
XPERIA TX{LT29}
XPERIA T{LT30}
XPERIA TL{LT30at}
XPERIA TIPO{ST21}
XPERIA TIPO DUAL{ST21_2}
XPERIA MIRO{ST23}
XPERIA U{ST25}
XPERIA J{ST26}
XPERIA GO{ST27}
XPERIA Sola{MT27}
Special THANKS go to the following XDA members for providing and maintaining links for the STOCK.ftf files above. Please click their THANKS button in the post you download from.
{dimon2242} {championswimmer} {Yakandu} {NomNomM} {zhuhang} {Spectre51} {hhlong89} {gregbradley} {Jozinek} {TeamMex} {Deadmask} {irontech}
PC Companion can interfere with FLASHTOOL. Make sure it is NOT running when using FLASHTOOL.
BATTERY CHARGING CYCLES
On a working phone there are different stages of a battery's charging cycle. The stages are listed in order they happen. The cycle goes from a completely dead battery through a phone running on battery and back to a completely dead battery.
Dead battery. No response from the power button, no screen and no led.
Connect to charger
low battery level charging mode. This is when just the RED led is on and no screen. At this stage the battery's charge is to low to turn the phone on, but it is charging.
Kernel controlled off-line charging mode. This is when the battery has charged enough from step (3) and boots the kernel to charge the battery. The phone is off, but could be turned on using the power button. A quick press of the power button will show this battery icon. Icon will fill with charge.
The kernel also controls charging when the phone is on.
Battery is fully charged.
Unplug the phone and turn on.
Battery is dead from normal use.
Repeat stages starting at (1)
Now, that is for a working phone. But if your reading this you don't care about a working cycle right? WRONG, this gives a baseline of charging check points to help in recovering your phone, so it is fairly important to understand.
A soft-brick charging cycle can restart at different points along the baseline while attempting to boot.
The kernel is the first thing to run at start-up.
If the kernel is broken the phone may.....
Lock-up before the kernel boot screen with just the back-light on.
Lock-up at the kernel boot screen.
get stuck in boot loops.
The SONY screen is displayed during kernel start-up, for a stock kernel.
A charging cycle for a phone with a broken kernel can go as far as stage (4) and then lock up or boot loop. Then the battery will have to die for the phone to reset and start over at step (1).
Thus ending a broken kernel cycle from dead battery to dead battery.
The system or ROM/firmware runs after the kernel starts successfully.
If the ROM is broken the phone may.....
Lock-up after the kernel screen with just the back-light on
Lock-up at the ROM boot screen
Get stuck in boot loops.
The XPERIA screen is displayed during ROM start-up, for a stock ROM.
A charging cycle for a phone with a broken ROM can go as far as stage (6) and then lock up or boot loop. Then the battery will have to die for the phone to reset and start over at step (1).
Thus ending a broken system cycle from dead battery to dead battery.
{SONY's PC Companion}
AN UNLOCKED BOOTLOADER WILL NEED TO BE RE-LOCKED FOR PC COMPANION TO WORK.
Thanks this is very helpful
thank you! Worked perfect!! as hard as it was to let the battery die I did it and she worked!!!
Before you wait all that time, try this. Hold the volume up button and the power button at the same time. The phone will vibrate once, keep holding until it vibrates 3 more times. Now you should be able to try flashing again. Worked for me.
44Blackhawk said:
Before you wait all that time, try this. Hold the volume up button and the power button at the same time. The phone will vibrate once, keep holding until it vibrates 3 more times. Now you should be able to try flashing again. Worked for me.
Click to expand...
Click to collapse
+1
In my case, trying to reset didn't work at all.
Yea same here as I could not get mine to do anything. I saw in another thread on this someone said once you get the Sony loop to do a force reset (1 buzz) and as soon as it buzz's hold volume down. You should see the green light flash and should then be able to connect it in flash mode again. Adds up with what I did and its very strange there is so much difference from device to device on a shared issue.
Edit: Pop why did you bale on the Ion???
The AHD is more responsive and the screen seems to be brighter and more clear and the glass was already scraching and the gorilla glass on the AHD will not.
Well was nice to have your help for as long as we did. Enjoy your new device.
popfan said:
The AHD is more responsive and the screen seems to be brighter and more clear and the glass was already scraching and the gorilla glass on the AHD will not.
Click to expand...
Click to collapse
The glass or the clear cover over it was?
Sent from my Sony Xperia S
popfan said:
The AHD is more responsive and the screen seems to be brighter and more clear and the glass was already scraching and the gorilla glass on the AHD will not.
Click to expand...
Click to collapse
Also known as Xperia ion lt28h.
General 2G Network GSM 850 / 900 / 1800 / 1900 3G Network HSDPA 850 / 900 / 1700 / 1900 / 2100 Announced 2012, April Status Available. Released 2012, June Body Dimensions 133 x 68 x 10.8 mm Weight 144 g - Touch-sensitive controls Display Type LED-backlit LCD, capacitive touchscreen, 16M colors Size 720 x 1280 pixels, 4.55 inches (~323 ppi pixel density) Multitouch Yes, up to 4 fingers Protection Scratch-resistant glass - Sony Mobile BRAVIA Engine
- Timescape UI Sound Alert types Vibration; MP3 ringtones Loudspeaker Yes 3.5mm jack Yes
Spectre51 said:
The glass or the clear cover over it was?
Sent from my Sony Xperia S
Click to expand...
Click to collapse
The glass itself. It has several small scratches into before I turned it in, just 28 days later. That is rather poor scratch-protection.
Does the Ion have the film over the glass like the Play did?? My Play scratched one day when I dropped it but figure I will just find me a high quality screen protector and replace it. Maybe some 3m product. I looked on the Ion and could not tell if it has it or not.
zackspeed said:
Does the Ion have the film over the glass like the Play did?? My Play scratched one day when I dropped it but figure I will just find me a high quality screen protector and replace it. Maybe some 3m product. I looked on the Ion and could not tell if it has it or not.
Click to expand...
Click to collapse
Yes it does.
Sent from my Sony Xperia S
popfan said:
The glass itself. It has several small scratches into before I turned it in, just 28 days later. That is rather poor scratch-protection.
Click to expand...
Click to collapse
The only way you could scratch the glass itself is if you removed the oem screen protector. You can't really tell its there until you know it's there. The X10 was the same way.
The included screen protector does scratch fairly easily and looks like scratched glass when it happens.
Sent from my Xperia ION using xda premium
if my screen is stuck on xperia logo. NOT BOOT LOOP. just stuck there. (unable to hard reset) cannot turn phone.
is this soft brick?
I performed these steps and it worked one time but when I did it a second time, it bricked my phone. It won't respond to any thing. Can somebody please help?!?
EDIT: Sorry guys, I freaked out last night and posted this before I did my reSEARCH. This is my problem now, I've been charging for phone for >9 hrs and it still hasn't turned on. It took about 6 hrs to get the red led light. When it came on, it was solid and not blinking. Should I just be patient?
You did not hard brick your phone. You will just have to do the steps all over again. Wait until the battery dies, then recharge and reflash. Make sure you battery is over 50%.
Just be patient and persistent. It can be very frustrating but you will get back in.
so i got my nexus 7 back around january and right when i got it i unlocked and rooted it with the tool kit. I was flashing many ROM's and kernals too but im a college student and got busy around march and so i wasnt using it and it was just sitting in my drawer. At the time it was in my drawer i remember it was working and powering on. So last month it came to my mind that i wanted to use the nexus 7 since i have time now. I go and look for it and when i found it and tried to turn it on it just wouldnt turn on.
First i plugged it into the charger with the ORIGINAL cable and plug for the whole day but when i plugged it in the screen started flashing every 3 seconds with a plain white light. So i tried booting into recovery using the power and volume buttons and that didint work. So i searched around the web and found that pulling out the battery and re connecting it works for most people. So i tried that and nothing changed. Right now its sitting plugged into the charger...flashing a white light every 3 seconds. So what else can i try? Idk if i have warranty too so im worried right now. The original owner received it as a gift and he was like 45 years old and didin't have the receipt to return it. My brother knows this guy because hes a regular customer and he bought it off of him and gave it to me knowing i like android devices. So i don't have a receipt for a RMA so idk what to do. Another thing is that the bootloader was unlocked last time i used it.
Please dont ignore this post and give me an opinion on what to do. Recommend me trying to give it to a electronics place to have them look at it and quote me how much would it cost me to get i fixed?
Your battery has discharged too low and your tablet has entered a form of hibernation to prevent it from becoming permanently damaged. Plug it in and hold all three hardware buttons to boot to the bootloader. From there, select power off. You should then be able to charge and use your device normally. These instructions are among the potential steps to take posted in the sticky thread at the top of this forum. http://forum.xda-developers.com/showthread.php?t=2090826
Well, I'm at a loss. Last night, I fell asleep reading a book on my N7. When I woke up this morning, I put it on my nightstand and went about my day. I came home tonight and it wouldn't boot up. I stuck it on the charger for about 30-50 minutes and went to boot it up and noticed not even the battery symbol would show up when I hit the power button while connected to the charger. This is with the factory charger. I tried multiple other chargers, nothing. I had Slim Bean Beta on it before this happened. It gave me no issues before today. I'm leaving it on the charger overnight, but I'm doubtful. Any ideas? I'm sick to my stomach over this. This is the first tablet I've ever bought and it was great up until today. I know it's just a material item, but I paid money for it only a year ago and expect to get more out of it. If anyone has thoughts or a way to get this thing going again, I'd greatly appreciate it. I'm pretty sure I'm out of my warranty period. Thanks guys.
t1.8matt said:
Well, I'm at a loss. Last night, I fell asleep reading a book on my N7. When I woke up this morning, I put it on my nightstand and went about my day. I came home tonight and it wouldn't boot up. I stuck it on the charger for about 30-50 minutes and went to boot it up and noticed not even the battery symbol would show up when I hit the power button while connected to the charger. This is with the factory charger. I tried multiple other chargers, nothing. I had Slim Bean Beta on it before this happened. It gave me no issues before today. I'm leaving it on the charger overnight, but I'm doubtful. Any ideas? I'm sick to my stomach over this. This is the first tablet I've ever bought and it was great up until today. I know it's just a material item, but I paid money for it only a year ago and expect to get more out of it. If anyone has thoughts or a way to get this thing going again, I'd greatly appreciate it. I'm pretty sure I'm out of my warranty period. Thanks guys.
Click to expand...
Click to collapse
Have you tried pressing and holding the power button for 20-30 seconds to force a reboot? Occasionally they freak out and lock up and need a forced reboot.
yeah, tried that. I'm following google's instructions to charge it over night and do the power hold to see if it starts up tomorrow. if not, i dunno. i'm not going to buy another N7, not with all the problems they've been having, even the Gen.2. I can't afford anything else, so I'll just have to wait and see tomorrow. It's just a bummer. I had nothing but problems with an Asus TF-101 my grandparents gave me to use for a little, and now this. Asus doesn't seem to have their stuff together when it comes to quality control on tablets. My Asus Ultrabook is great, but these tablets are a different story.
Was it set to never turn off the backlight when reading? It's probable you are suffering from the battery bug that is posted in numerous spots.
Sent from my Nexus 7(2012) that has zero issues.
t1.8matt said:
Well, I'm at a loss. Last night, I fell asleep reading a book on my N7. When I woke up this morning, I put it on my nightstand and went about my day. I came home tonight and it wouldn't boot up. I stuck it on the charger for about 30-50 minutes and went to boot it up and noticed not even the battery symbol would show up when I hit the power button while connected to the charger. This is with the factory charger. I tried multiple other chargers, nothing. I had Slim Bean Beta on it before this happened. It gave me no issues before today. I'm leaving it on the charger overnight, but I'm doubtful. Any ideas? I'm sick to my stomach over this. This is the first tablet I've ever bought and it was great up until today. I know it's just a material item, but I paid money for it only a year ago and expect to get more out of it. If anyone has thoughts or a way to get this thing going again, I'd greatly appreciate it. I'm pretty sure I'm out of my warranty period. Thanks guys.
Click to expand...
Click to collapse
Try connecting it to your PC, if the computer shows APX Mode in Device Manager then I can help you out with it.
Just contacted Google and Asus, will be returned for RMA. Still covered under warranty since it was purchased in January, I luckily just found the receipt. I'm wondering if I should have just taken it back to Gamestop where I purchased it from instead of going through Asus.
t1.8matt said:
Just contacted Google and Asus, will be returned for RMA. Still covered under warranty since it was purchased in January, I luckily just found the receipt. I'm wondering if I should have just taken it back to Gamestop where I purchased it from instead of going through Asus.
Click to expand...
Click to collapse
The Sero 7 Pro by Hisense is totally up to par with this N7, plus it has a back cam, a micro sd slot for storage expansion, and only for $129.00 at Walmart. Maybe some devs can manage to port the N7 roms over.
Jorghe1025 said:
Try connecting it to your PC, if the computer shows APX Mode in Device Manager then I can help you out with it.
Click to expand...
Click to collapse
I'm gonna give that a try in a bit and let you know. I was gonna take it apart to see if the battery connection came loose but since I'm probably gonna return it I'm not going to do that in case I damage the backing taking apart.
is asus gonna give me a load of crap if they get it to boot and see that the bootloader is unlocked and running a different rom?
i plugged it into my computer and it recognizes it as an unknown device. no apx or anything else, just unknown. windows makes the sound that something got plugged in but i can't really find it.
got it, it's in APX mode
t1.8matt said:
i plugged it into my computer and it recognizes it as an unknown device. no apx or anything else, just unknown. windows makes the sound that something got plugged in but i can't really find it.
Click to expand...
Click to collapse
Try to google "Nexus 7 ADB APX Drivers", install them and try again.
It did happen to me the first time
---------- Post added at 04:20 PM ---------- Previous post was at 04:07 PM ----------
t1.8matt said:
got it, it's in APX mode
Click to expand...
Click to collapse
OK, follow carefully,
*Connect it to your PC
*Press and hold the power button while connected for about 15 to 30 secs.
*the bootloader will appear
*restore to stock using the Nexus 7 Root Toolkit
If failed wait 20 to 30 minutes WITH the N7 plugged in to your PC, disconnect it, reconnect it and try again.
That did save me from a $210 Brick.
Jorghe1025 said:
Try to google "Nexus 7 ADB APX Drivers", install them and try again.
It did happen to me the first time
---------- Post added at 04:20 PM ---------- Previous post was at 04:07 PM ----------
OK, follow carefully,
*Connect it to your PC
*Press and hold the power button while connected for about 15 to 30 secs.
*the bootloader will appear
*restore to stock using the Nexus 7 Root Toolkit
If failed wait 20 to 30 minutes WITH the N7 plugged in to your PC, disconnect it, reconnect it and try again.
That did save me from a $210 Brick.
Click to expand...
Click to collapse
I'll try it in a bit and let you know. If it doesn't work I just hope Asus doesn't give me a hard time about it being modified.
Buh Bye Warranty
Yes.. The warranty will be voided due to rooting the N7. Follow the instructions from everyone here and they will help you get it working. If the computer is recognizing their is hope.. Repeat this Mantra 'Help me XDA, you're my only hope'
Stop getting into a tizzy and dont give up so easy...lol
Be patient, calm, and logical and this will easily get fixed.
No tizzy here, I'm not through until I've exhausted all possibilities. Thanks guys.
no bootloader after following instructions. tried with power button and power button with volume keys.
Just want to give an update. Asus fixed my tablet and i should have it Monday. Won't know for sure how it is until it gets here but I'm pretty pleased with their service.
Oh, and I never received an email or phone call that they couldn't fix it because of being modded so that must be a positive sign.
t1.8matt said:
Oh, and I never received an email or phone call that they couldn't fix it because of being modded so that must be a positive sign.
Click to expand...
Click to collapse
Usually hardware faults are covered even on modified software.
Sent from my Nexus 7 using xda app-developers app
I'm hoping they include a reason as to why it quit working but i doubt they will.
Okay about two weeks ago I updated to 4.4.2 from 4.2.2(I think that's the one?) on my s4 and I've hated the update. I decided to root my phone using muniz method and it worked perfectly. I even changed to the nc1.
So, after using my phone without issues for two weeks roughly I noticed last night it started to randomly turn off while texting. It would just auto restart but it happened every 5-10 minutes. After an hour it started happening more often so I plugged my phone in. Now my phone will not even turn on. When I insert the battery the samsung start screen appears for about a second and then goes black. I have to pull out the battery for the phone to do ANYTHING. If the phone is plugged in while trying this and I insert the battery I literately get NOTHING. No samsung screen or anything.
Things I've tried.
Swapped the battery.
boot into odin
boot into safemode
plugged it in while trying to boot
Swapped the usb cord
taken out sim card
Some things to note is that I did not install any new app before this had happened. It was working the same for about two weeks with no issues.
When plugging in my phone to charge or anything I never get an led light at the top of my phone.
I seriously need some help with this. Any suggestions are appreciated!
Conquestfan said:
Okay about two weeks ago I updated to 4.4.2 from 4.2.2(I think that's the one?) on my s4 and I've hated the update. I decided to root my phone using muniz method and it worked perfectly. I even changed to the nc1.
So, after using my phone without issues for two weeks roughly I noticed last night it started to randomly turn off while texting. It would just auto restart but it happened every 5-10 minutes. After an hour it started happening more often so I plugged my phone in. Now my phone will not even turn on. When I insert the battery the samsung start screen appears for about a second and then goes black. I have to pull out the battery for the phone to do ANYTHING. If the phone is plugged in while trying this and I insert the battery I literately get NOTHING. No samsung screen or anything.
Things I've tried.
Swapped the battery.
boot into odin
boot into safemode
plugged it in while trying to boot
Swapped the usb cord
taken out sim card
Some things to note is that I did not install any new app before this had happened. It was working the same for about two weeks with no issues.
When plugging in my phone to charge or anything I never get an led light at the top of my phone.
I seriously need some help with this. Any suggestions are appreciated!
Click to expand...
Click to collapse
Are you plugging it in to the stock wall charger? Your best bet is to get it to boot into download mode long enough to reflash NB1.
Sent from my SGH-I337 running BlackBox 3.0
DeadlySin9 said:
Are you plugging it in to the stock wall charger? Your best bet is to get it to boot into download mode long enough to reflash NB1.
Sent from my SGH-I337 running BlackBox 3.0
Click to expand...
Click to collapse
Yeah using stock wall charger from a wall, computer, and even a different charger.
Is download mode the one where you hold vol down + power + home?
If so it brings up the screen that asks you to press the volume up but it dies before it can ever make it to the downloading screen...
Conquestfan said:
Yeah using stock wall charger from a wall, computer, and even a different charger.
Is download mode the one where you hold vol down + power + home?
If so it brings up the screen that asks you to press the volume up but it dies before it can ever make it to the downloading screen...
Click to expand...
Click to collapse
Experiment and see if you can get it to stay there. If not, you may need to try a best buy if you can.
Sent from my SGH-I337 running BlackBox 3.0
Thanks, i'll keep playing with it but so far it just shuts off instantly in about a second or two.
If I bring it to best buy and they take it or anywhere else will I be shunned for rooting my phone?
Conquestfan said:
Thanks, i'll keep playing with it but so far it just shuts off instantly in about a second or two.
If I bring it to best buy and they take it or anywhere else will I be shunned for rooting my phone?
Click to expand...
Click to collapse
If it won't start they won't know it's rooted. They'll try to flash the firmware which will remove root if they're successful, so again they won't know
Sent from my Nexus 5 using XDA Free mobile app
That would be fantastic! If I purshased it at walmart would it matter if I take it to best buy for example? I'm sure a corporate AT&T store could do the same correct?
Conquestfan said:
That would be fantastic! If I purshased it at walmart would it matter if I take it to best buy for example? I'm sure a corporate AT&T store could do the same correct?
Click to expand...
Click to collapse
Go to a best buy that has a Samsung experience. They can re-flash it there
Sent from my Nexus 5 using XDA Free mobile app
jd1639 said:
Go to a best buy that has a Samsung experience. They can re-flash it there
Sent from my Nexus 5 using XDA Free mobile app
Click to expand...
Click to collapse
put it in downloadvolume down power and home button use odin to load factory file hope this helps
ron31 said:
put it in downloadvolume down power and home button use odin to load factory file hope this helps
Click to expand...
Click to collapse
I've tried this but it instantly shuts off as soon as the volume up screen to continue comes up. It won't boot in any form at all
Conquestfan said:
I've tried this but it instantly shuts off as soon as the volume up screen to continue comes up. It won't boot in any form at all
Click to expand...
Click to collapse
did you try factory reset
ron31 said:
did you try factory reset
Click to expand...
Click to collapse
I couldn't do factory reset because the phone wouldn't stay on long enough to do ANYTHING.
So as an update to this...
I was on my way to the closest store with samsung experience which is about an hour away from me and when I almost get there my phone RANDOMLY turns on...
I couldn't be more pissed and happy at the same time. So, obviously I try messing with it a bit and it shuts off again. This time I can get it to turn on after about 15 tries. Long enough for me to do a factory reset!
It lasted a good 30 minutes to an hour and it shut off again.
Hardware issue or is anyone else having this issue with 4.4.2 nc1?
No I haven't on mine you all have to bring it in for repair
ron31 said:
No I haven't on mine you all have to bring it in for repair
Click to expand...
Click to collapse
Okay so I brought it by best buy and the guys couldn't flash it or do anything to it because it wouldn't turn on at all. They tried several batteries etc.
So, I decided to try the phone doctors and the guy thought it could be a malfunction in the power button because the phone tries to boot up any time you put the battery in. You don't have to hit any buttons and you can't insert the battery without it trying to power on.
I'll cross my fingers that's the problem and they phone doctor guy told me he has never seen this issue with an s4 but it was really common in s3's.
I go back in two hours to see if they have fixed it!
Conquestfan said:
Okay so I brought it by best buy and the guys couldn't flash it or do anything to it because it wouldn't turn on at all. They tried several batteries etc.
So, I decided to try the phone doctors and the guy thought it could be a malfunction in the power button because the phone tries to boot up any time you put the battery in. You don't have to hit any buttons and you can't insert the battery without it trying to power on.
I'll cross my fingers that's the problem and they phone doctor guy told me he has never seen this issue with an s4 but it was really common in s3's.
I go back in two hours to see if they have fixed it!
Click to expand...
Click to collapse
The s2 had this problem too and one way to confirm it was to pull the battery and put it back in. If it booted right away it was the power button. So it sounds like you're on to something.
Sent from my Nexus 5 using XDA Free mobile app
jd1639 said:
The s2 had this problem too and one way to confirm it was to pull the battery and put it back in. If it booted right away it was the power button. So it sounds like you're on to something.
Sent from my Nexus 5 using XDA Free mobile app
Click to expand...
Click to collapse
Well, I was really hoping for the best and I thought they really had my problem figured out. When I got back to the store they told me they basically checked and rewired everything they could and it was still doing this. They told me they can't fix it and didn't charge me anything.
It looks like I have a lemon...
Conquestfan said:
Well, I was really hoping for the best and I thought they really had my problem figured out. When I got back to the store they told me they basically checked and rewired everything they could and it was still doing this. They told me they can't fix it and didn't charge me anything.
It looks like I have a lemon...
Click to expand...
Click to collapse
send it back to samsung
ron31 said:
send it back to samsung
Click to expand...
Click to collapse
I would but they don't accept anything past a year. If it ever boots up again I'm going to install a different rom and just cross fingers
I've been informed my phone might still be under factory warranty. Just out of speculation, if you root your phone and it ends up malfunctioning what would they do if you send it in for warranty? I'm not sure if my issue is hardware or software related at all.
My phone randomly shut off today at around 14% battery. I'm assuming that the battery level wasn't correctly calculated and it was actually at 0%, which is pretty common for my phone.
Now, when I plug it in I don't get any charging icon appearing at all. I've tried a different charger and it has the same result.
Is this perhaps because the phone is extremely low on battery? At times I've found when it is some software doesn't function - could the charging icon not appear because it is so low on battery?
If not, is it likely my phone's battery is dead?
Thanks for any input into this issue. :good:
Does the LED flash when you connect the phone to the charger? Did you try leaving it on the charger for a few hours?
Charge your phone for 2-3 hours and then try to start it. If it doesn't work, then you might have to follow this: https://forum.xda-developers.com/nexus-4/general/how-to-bring-nexus-4-battery-dead-t2975391
Nitin
MORE Nexus 4 Issues 2017
I need your help! My Nexus 4 on 4.4.3 is stuck in a boot loop! I don't know how this happened; however the [fix root? (Yes)] option in CWM recovery is missing! and I can't boot into safe mode to uninstall an app that I think might be causing this; (My phone died while I was using Hangouts and the bottom LED light flashed twice. That's the last thing I remembered before my phone became....a paper weight. Do you have any suggestions? Is there a way to boot into Safe Mode via. ADB or a button command on KitKat? I freally do not want to factory reset my device. I have too many unupdated apps and pictures and personal things on my phone that I've been building for... well 4 years since I've gotten the phone. Any advice will be appreciated, - Milo
---------- Post added at 05:35 AM ---------- Previous post was at 05:35 AM ----------
I need your help! My Nexus 4 on 4.4.3 is stuck in a boot loop! I don't know how this happened; however the [fix root? (Yes)] option in CWM recovery is missing! and I can't boot into safe mode to uninstall an app that I think might be causing this; (My phone died while I was using Hangouts and the bottom LED light flashed twice. That's the last thing I remembered before my phone became....a paper weight. Do you have any suggestions? Is there a way to boot into Safe Mode via. ADB or a button command on KitKat? I freally do not want to factory reset my device. I have too many unupdated apps and pictures and personal things on my phone that I've been building for... well 4 years since I've gotten the phone. Any advice will be appreciated, - Milo