Hi al how are u. My htc hd2 is stuck at the aMgldr . Boot ad sd and boot ad nand both doesnt work. I dont kno why bt. Wen i select them on scren it does goes any forward from the 123456 Go Go Go and is stuck at that screen. Anyone knows any soluton are more than welcome to share plz:
Have you tried re-flashing magldr?
Yes tried everythng from hspl.. bt still same prblm any idea.. hrlp plz
Iss my moble dead..? Or may i try windwz stock...?
You could try windows stock to boot android via haret, note; kernels >2.6.32 won't boot from haret
Or clk.
It might be that you have developed a bad block in the area of nand where magldr is loaded.
You might be able to check this by booting android, installing an app (eg catlog i think, or logcat extreme) which can show dmesg logs and searching for "bad block" in the output.
Robbie P said:
You could try windows stock to boot android via haret, note; kernels >2.6.32 won't boot from haret
Or clk.
It might be that you have developed a bad block in the area of nand where magldr is loaded.
You might be able to check this by booting android, installing an app (eg catlog i think, or logcat extreme) which can show dmesg logs and searching for "bad block" in the output.
Click to expand...
Click to collapse
Ok will try stock rom... bt is there any bootloader etc which can load from Sd card or the ext4 partition
RASHIDDDDD said:
Ok will try stock rom... bt is there any bootloader etc which can load from Sd card or the ext4 partition
Click to expand...
Click to collapse
You can use clk to boot NativeSD and SD builds, you just need to put the initrd.gz and zImage in the /sdcard/NativeSD folder, create an sboot nand partition in clk and use flash_sboot_v2 to create a boot.img in the sboot partition, and boot it from there using clk. You can have different NativeSD roms/sd builds booting from different partitions, tboot, uboot, vboot etc
Read the clk thread for more info.
I had the same Problem ...
Well ... I Had such problem and when I Hard reseted and then Did a T29 and finally re flashing MAGLDR solved mine
Robbie P said:
You can use clk to boot NativeSD and SD builds, you just need to put the initrd.gz and zImage in the /sdcard/NativeSD folder, create an sboot nand partition in clk and use flash_sboot_v2 to create a boot.img in the sboot partition, and boot it from there using clk. You can have different NativeSD roms/sd builds booting from different partitions, tboot, uboot, vboot etc
Read the clk thread for more info.
Click to expand...
Click to collapse
and i have also noticed that in tri color bootloader the Cotulla Hspl is missing and is Blank does it have anything to do with it??
RASHIDDDDD said:
and i have also noticed that in tri color bootloader the Cotulla Hspl is missing and is Blank does it have anything to do with it??
Click to expand...
Click to collapse
mine says
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Click to expand...
Click to collapse
Seems like you need to put HSPL on it with SPL 2.08
Now flashed win mob 6.5 stock turn sout that my Leo touch is dead
Related
I have a us T-Mobile htc hd2 which was running android nand sense and I had a touch screen issue. I found the fix to revert my phone back to factory, un-installing hspl back to spl. Sent the phone off to htc which they replaced the screen under the warranty. I got my phone back and tried to put the same programs and files I used in the beginning
I have spent hours reading and trying things suggested like using a radio file Radio_Leo_2.15.50.14, I have downgraded spl from my 2.10.000 to 2.08.000
When the phone reboots I get a message ss sd kernel open fail then MAGLDR Boot Menu Screen but am unable to load files with the usb
Any help?
imglknight said:
I have a us T-Mobile htc hd2 which was running android nand sense and I had a touch screen issue. I found the fix to revert my phone back to factory, un-installing hspl back to spl. Sent the phone off to htc which they replaced the screen under the warranty. I got my phone back and tried to put the same programs and files I used in the beginning
I have spent hours reading and trying things suggested like using a radio file Radio_Leo_2.15.50.14, I have downgraded spl from my 2.10.000 to 2.08.000
When the phone reboots I get a message ss sd kernel open fail then MAGLDR Boot Menu Screen but am unable to load files with the usb
Any help?
Click to expand...
Click to collapse
Hi,
Did you install HSPL 2.08HSPL?
THIS TOOL is very useful for everything you need...
yes I loaded hspl 208
I tried again and got the same error from MAGLDR113 sd kernl open fail and I tried to port DEFT Android again and got this error message
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)
imglknight said:
yes I loaded hspl 208
I tried again and got the same error from MAGLDR113 sd kernl open fail and I tried to port DEFT Android again and got this error message
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)
Click to expand...
Click to collapse
Hi,
You need to start from scratch...
Before starting anything,BACKUP YOUR DATA.
Download THIS TOOL
Flash radio...download HERE Enter bootloader:hold down volume button when you power on phone.When you are on tri-color screen,insert cable to usb.When screen changes from "serial"to "usb",proceed.
Open HD2 Installer:
Task 29 (Enter bootloader:as above)
HSPL 2.08 HSPL (Enter bootloader:as above)
MAGLDR (Enter bootloader:as above)
(when magldr has loaded,power on and enter by holding power button until you see magldr screen.)
(when this is done,Go to ad recovery>advanced>Partition SD Card.1024m with 0 cache)
Repartition according to ROM requirements.(via number 5 usb flasher)
Then go to ad recovery and wipe data,cache partition,and dalvik(advanced).
Then go to install zip from sd card (which you should have placed on the root of your sd card)
reboot.
Give it time.Some ROMS take 15-20 minutes to install.
malybru said:
Hi,
You need to start from scratch...
Before starting anything,BACKUP YOUR DATA.
Download THIS TOOL
Flash radio...download HERE Enter bootloader:hold down volume button when you power on phone.When you are on tri-color screen,insert cable to usb.When screen changes from "serial"to "usb",proceed.
Open HD2 Installer:
Task 29 (Enter bootloader:as above)
HSPL 2.08 HSPL (Enter bootloader:as above)
MAGLDR (Enter bootloader:as above)
(when magldr has loaded,power on and enter by holding power button until you see magldr screen.)
(when this is done,Go to ad recovery>advanced>Partition SD Card.1024m with 0 cache)
Repartition according to ROM requirements.(via number 5 usb flasher)
Then go to ad recovery and wipe data,cache partition,and dalvik(advanced).
Then go to install zip from sd card (which you should have placed on the root of your sd card)
reboot.
Give it time.Some ROMS take 15-20 minutes to install.
Click to expand...
Click to collapse
I dont get it ....I have problems with this (when this is done,Go to ad recovery>advanced>Partition SD Card.1024m with 0 cache) I cant get there when i go to ad recovery it says "no boot sources " ...please help ...:-/
Im sitting with this phone already 3 days ...I start to hate it ....I had windows 6.5 then I put Android on but the problem was that i couldn't get right radio ...so I didnt had 3G/H ......does anybody know if there are some special link for HTC HD 2 Leo T-Mobile 1024....???step by step how to put on android with working i-net connection?????
Did you install Clockworkmod? Can be found here
renars.k said:
I dont get it ....I have problems with this (when this is done,Go to ad recovery>advanced>Partition SD Card.1024m with 0 cache) I cant get there when i go to ad recovery it says "no boot sources " ...please help ...:-/
Im sitting with this phone already 3 days ...I start to hate it ....I had windows 6.5 then I put Android on but the problem was that i couldn't get right radio ...so I didnt had 3G/H ......does anybody know if there are some special link for HTC HD 2 Leo T-Mobile 1024....???step by step how to put on android with working i-net connection?????
Click to expand...
Click to collapse
Hi,
Sorry,I've been really busy.
Try in the order of things...
1.use toolkit to install HSPL 2.08 HSPL
2.Task 29
3.Flash radio
4.install magldr and so on from there.
Then the rest is the same on the list.
Am I getting the error message “Error Description: USB init failed” because I don’t have a sd card in the phone? Is that where I am going wrong?
make sure that the files initrd and zimage are copied to the root of the sd card. do not copy the whole foler bec magldr will not be able to recognize it.
hello
i want to install [3.May.11][MAG/cLK] NexusHD2-Gingerbread V2.7 [GRJ22/Android2.3.4][Kernel:tytung_r10]
but after i flash clk or MAGLDR the phone wont boot anymore it stucks on htc logo dont know why and i had android before but i flashed to winm 6.5 stock and now i want android again...
what im i doing wrong ?
ssj3g0ku said:
hello
i want to install [3.May.11][MAG/cLK] NexusHD2-Gingerbread V2.7 [GRJ22/Android2.3.4][Kernel:tytung_r10]
but after i flash clk or MAGLDR the phone wont boot anymore it stucks on htc logo dont know why and i had android before but i flashed to winm 6.5 stock and now i want android again...
what im i doing wrong ?
Click to expand...
Click to collapse
Hi,
Before starting anything,BACKUP YOUR DATA.
Download THIS TOOL
Flash radio...download HERE Enter bootloader:hold down volume button when you power on phone.When you are on tri-color screen,insert cable to usb.When screen changes from "serial"to "usb",proceed.
Open HD2 Installer:
Task 29 (Enter bootloader:as above)
HSPL 2.08 HSPL (Enter bootloader:as above)
MAGLDR (Enter bootloader:as above)
(when magldr has loaded,power on and enter by holding power button until you see magldr screen.)
(when this is done,Go to ad recovery>advanced>Partition SD Card.1024m with 0 cache)
Repartition according to ROM requirements.(via number 5 usb flasher)
Then go to ad recovery and wipe data,cache partition,and dalvik(advanced).
Then go to install zip from sd card (which you should have placed on the root of your sd card)
reboot.
Give it time.Some ROMS take 15-20 minutes to install.
ssj3g0ku said:
but after i flash clk or MAGLDR the phone wont boot anymore it stucks on htc logo dont know why
Click to expand...
Click to collapse
wrong radio OR wrong hspl
It MUST be 2.08.hspl and any radio 2.07.50 or higher, but MUST be .50, not .51
yeah radio was the problem,i managed to install 2.2 and worked good but the in call sound was... not so good.not sure what android version or rom should i choose
now im back to windows mobile its so slow
i have the hd2 512 version
try another radio.
i use Radio: 2.15.50.14
is known bug that some radios make an robot voice. but sometimes it is only in the first call, second one is ok...... try it pls
Stuck in magldr its wont reboot back to wm6.5 is there anything i can do
generally
wrong recovery size or kernel problem
you have to use preffered recovery size and kernel if it is not working (recovery size) other options flash a new kernel tytung or hieros etc...
Hi,
I tried today to flash android to my HTC HD2 but it went wrong
I flashed the radio 2.08 HSPL and the phone started oke to windows.
But when I updated the rom to install magldr it said that it was successful but the phone stuck in the white screen with green HTC logo and did not show magldr or any thing else just the htc screen
Please help me to repair it and flash android.
When I press volume down en power button I get the 4 colors screen. I get this text on it:
PB1100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
PLEASE HELP ME
Use task29 to remove windows first
than flash your phone with HSPL4 to 2.08.HSPL
than update your radio to 2.15.50.14
install magldr1.13
Restart the phone go to USB massSTG
plug your phone to the pc.
Copy the rom.zip to the phone.
Go back to home page
Go to USB flasher and install from your pc CWM daf.exe.
Phone starts automaticly.
Go to AD recovery, install zip from SD, choose zip from SD, choose your rom choose YES when finished go back and reboot system now.
It should to be work
Good Luck
and for future reference please post in the correct section, Q&A NOT the dev section
Please check my signature and follow the details instruction. mskip wrote it very clear. if you still have problem please let me know,,,
stuiterbal187 said:
Use task29 to remove windows first
than flash your phone with HSPL4 to 2.08.HSPL
than update your radio to 2.15.50.14
install magldr1.13
Restart the phone go to USB massSTG
plug your phone to the pc.
Copy the rom.zip to the phone.
Go back to home page
Go to USB flasher and install from your pc CWM daf.exe.
Phone starts automaticly.
Go to AD recovery, install zip from SD, choose zip from SD, choose your rom choose YES when finished go back and reboot system now.
It should to be work
Good Luck
Click to expand...
Click to collapse
I did everything except updating the radio to 2.15.50.14... How can I do that?
Thnx
I flashed the radio to 2.15.50.14 I found here: http://forum.xda-developers.com/showthread.php?t=611787
I installed the recovery and it's working BUT it does not install ROMs The error is: Can't open the ROM
How can I solve this again
SOLVED. Look here: http://forum.xda-developers.com/showthread.php?p=16785804#post16785804
Hi
I have a HTC HD2 bought in Norway.
I want to run Android on this instead of WPH.
What I have done is:
1: Installed MAGLDR 1.13
2: I used HSPL4 and installed HSPL2.08
3: I have the radio versjon 2.15.50.14.
4: I booted up in MAGLDR, and flashed the ROM via menu 5, Flash via USB.
5: I have downloaded the DFT_LEO_NAND_Android, and ran the DAF-tool.
Everything looks good, but when it is finished, the phone restarts, and boots up in nand, 1 2 3 4 5 6, GO, GO, GO, the Android logo shows, and nothing more!
This also happens if I try to boot up from SD-card with an Android folder with a custom ROM, its freezing on the green HTC-logo aften MAGLDR boot.
I have deleted my WPH image, so I cant boot up in windows anymore.
I have tryed to hard-reset the phone (hold down volume up and down + power + reset).
I have NEVER come it to bootloader with green, red, brue and white screen during bootup. Only time I got this, was when I ran the ROMUpdateUtility in windows when the phone still ran WPH. This I can not do anymore due that I cant boot Windows anymore.
Can I flash any WPH ROM i MAGLDR?
Should I install ClockworkRecovery? How?
Can someone please help! Thanks.
abbamust said:
Hi
I have a HTC HD2 bought in Norway.
I want to run Android on this instead of WPH.
What I have done is:
1: Installed MAGLDR 1.13
2: I used HSPL4 and installed HSPL2.08
3: I have the radio versjon 2.15.50.14.
4: I booted up in MAGLDR, and flashed the ROM via menu 5, Flash via USB.
5: I have downloaded the DFT_LEO_NAND_Android, and ran the DAF-tool.
Everything looks good, but when it is finished, the phone restarts, and boots up in nand, 1 2 3 4 5 6, GO, GO, GO, the Android logo shows, and nothing more!
This also happens if I try to boot up from SD-card with an Android folder with a custom ROM, its freezing on the green HTC-logo aften MAGLDR boot.
I have deleted my WPH image, so I cant boot up in windows anymore.
I have tryed to hard-reset the phone (hold down volume up and down + power + reset).
I have NEVER come it to bootloader with green, red, brue and white screen during bootup. Only time I got this, was when I ran the ROMUpdateUtility in windows when the phone still ran WPH. This I can not do anymore due that I cant boot Windows anymore.
Can I flash any WPH ROM i MAGLDR?
Should I install ClockworkRecovery? How?
Can someone please help! Thanks.
Click to expand...
Click to collapse
download and install this tool to pc.
http://forum.xda-developers.com/showthread.php?t=1090783
1)go to android nand thread and find a rom to your pleasure
2)in op of rom find which nand partition you need
3)using tool arrange and apply this nand partition in usb flasher mode (e.g. if it says 5-180-5 you'll choose custom at left column and 5 as cache,then click repartition and write 180 in the coming window.)
4)if your hd2 is eu,then make an ext partition. in mgldr:ad recovery-advanced-partition sd card-choose 1024-choose 0.(this procedure will wipe everything in sd)
5)put your rom.zip file to sd: in mgldr:ad recovery-monts and storage-mount usb storage-send your file to sd
6)now press back button-select install zip from sd-choose zip rom sd-find your rom.zip.
7)after installation is complete reboot.
Thanks, but where can I find which nand partition I need?
Ex, MDJ_Gingerbread or, JDMS, DTF_LEO_NAND
abbamust said:
Thanks, but where can I find which nand partition I need?
Ex, MDJ_Gingerbread or, JDMS, DTF_LEO_NAND
Click to expand...
Click to collapse
can you give the link of the rom you want to use?
I tried the HD2 toolkit, but I did not know what sizs to choose, but I just tried 150 with 5 in cache.
Then entered magldr, and when I coosed AD recovery, the phone hangs. No menu.
I also tried to install Clockworkmod Recovery, and I never got the menu for Clockwork. Enters magldr, and when I press Boot AD to enter Clockwork, it hangs again. 123456 GO GO GO, and nothing...
http://www.jayceooi.com/2011/01/03/download-jdms-ultimate-nand-android-rom-for-htc-hd2/
http://forum.xda-developers.com/showthread.php?t=893620
http://www.addictivetips.com/mobile/install-gingerbread-based-typhoon-cyanogenmod-7-rom-on-htc-hd2/
abbamust said:
I tried the HD2 toolkit, but I did not know what sizs to choose, but I just tried 150 with 5 in cache.
Then entered magldr, and when I coosed AD recovery, the phone hangs. No menu.
I also tried to install Clockworkmod Recovery, and I never got the menu for Clockwork. Enters magldr, and when I press Boot AD to enter Clockwork, it hangs again. 123456 GO GO GO, and nothing...
http://www.jayceooi.com/2011/01/03/download-jdms-ultimate-nand-android-rom-for-htc-hd2/
http://forum.xda-developers.com/showthread.php?t=893620
http://www.addictivetips.com/mobile/install-gingerbread-based-typhoon-cyanogenmod-7-rom-on-htc-hd2/
Click to expand...
Click to collapse
To flash clockworkmod, you use USB Flasher mode (in Magldr). To enter clockworkmod recovery afterwards, you go to 8. AD Recovery. Going to boot AD will not go into the recovery.
abbamust said:
I tried the HD2 toolkit, but I did not know what sizs to choose, but I just tried 150 with 5 in cache.
Then entered magldr, and when I coosed AD recovery, the phone hangs. No menu.
I also tried to install Clockworkmod Recovery, and I never got the menu for Clockwork. Enters magldr, and when I press Boot AD to enter Clockwork, it hangs again. 123456 GO GO GO, and nothing...
http://www.jayceooi.com/2011/01/03/download-jdms-ultimate-nand-android-rom-for-htc-hd2/
http://forum.xda-developers.com/showthread.php?t=893620
http://www.addictivetips.com/mobile/install-gingerbread-based-typhoon-cyanogenmod-7-rom-on-htc-hd2/
Click to expand...
Click to collapse
i used the third rom (typhoon's) before. it needs 150-5 partition. the other two are very old roms. so using nand tool,make 150-5 partition in mgldr usb flasher mode.then try going to ad recovery again.it should work.
Nigeldg said:
To flash clockworkmod, you use USB Flasher mode (in Magldr). To enter clockworkmod recovery afterwards, you go to 8. AD Recovery. Going to boot AD will not go into the recovery.
Click to expand...
Click to collapse
Sorry, I ment AD Recovery, and the phone goes not i Cloclwork recovery anyway...
mutil said:
i used the third rom (typhoon's) before. it needs 150-5 partition. the other two are very old roms. so using nand tool,make 150-5 partition in mgldr usb flasher mode.then try going to ad recovery again.it should work.
Click to expand...
Click to collapse
This is what happens when I try to enter ad recovery.
This is what happen when I try to load AD from SD.
Here it just freezes.
abbamust said:
This is what happens when I try to enter ad recovery.
Click to expand...
Click to collapse
this screen is normal, but it must go further after this screen. what i say, if you apply nand partition again this problem may be solved.because it will give you a new ad recovery.if it doesnt work we can try a different recovery.
mutil said:
this screen is normal, but it must go further after this screen. what i say, if you apply nand partition again this problem may be solved.because it will give you a new ad recovery.if it doesnt work we can try a different recovery.
Click to expand...
Click to collapse
I use the Recovery_150M now, and till just hangs when I enter ad recovery.
Witch else can I use?
abbamust said:
I use the Recovery_150M now, and till just hangs when I enter ad recovery.
Witch else can I use?
Click to expand...
Click to collapse
http://api.viglink.com/api/click?fo...ry v3.0.2.5)&jsonp=vglnk_jsonp_13142666346961
download and unrar this.connect your phone to pc. in mgldr choose 'usb flasher'. see usb flasher...usb in phone screen.-in unrared folder right click on daf.exe-run as administrator.then install your rom.zip from sd.
mutil said:
http://api.viglink.com/api/click?fo...ry v3.0.2.5)&jsonp=vglnk_jsonp_13142666346961
download and unrar this.connect your phone to pc. in mgldr choose 'usb flasher'. see usb flasher...usb in phone screen.-in unrared folder right click on daf.exe-run as administrator.then install your rom.zip from sd.
Click to expand...
Click to collapse
Thank you for trying to help me.
The new recovery got flashed nice, but at bootup on SD-card witch I put the Typhoon CM7 android, it freezes at bootup. 123456 GO GO GO. and then android picture, nothing more. I have waited for maybe 1 hour for the installation.
Is my phone briked now?
one little ting.
seems like i have aMAGLDR v1.13.
abbamust said:
Thank you for trying to help me.
The new recovery got flashed nice, but at bootup on SD-card witch I put the Typhoon CM7 android, it freezes at bootup. 123456 GO GO GO. and then android picture, nothing more. I have waited for maybe 1 hour for the installation.
Is my phone briked now?
Click to expand...
Click to collapse
i dont think so. now in ad recovery wipe data/factory reset then try flashing the rom again.if it doesnt work download a new copy of rom and send it to sd, wipe data/factory reset and flash.
mutil said:
i dont think so. now in ad recovery wipe data/factory reset then try flashing the rom again.if it doesnt work download a new copy of rom and send it to sd, wipe data/factory reset and flash.
Click to expand...
Click to collapse
OK, when I go in ad recovery, I got no new menu. Only screen like this:
ANDROID LOAD RAW
[K]11808800:28BC18 *****************
Load done!
123456
GO GO GO!
And nothing more...
And when you say flash new rom, for the TyphoonN_CM7_v2.7.4, do you mean copy those to files to root of SD, and then boot from SD?
Only ROM I can flash via USB flasher mode is a DFT LEO NAND Android. And If I do that, it freezes at the DFT-logo...
abbamust said:
OK, when I go in ad recovery, I got no new menu. Only screen like this:
ANDROID LOAD RAW
[K]11808800:28BC18 *****************
Load done!
123456
GO GO GO!
And nothing more...
And when you say flash new rom, for the TyphoonN_CM7_v2.7.4, do you mean copy those to files to root of SD, and then boot from SD?
Only ROM I can flash via USB flasher mode is a DFT LEO NAND Android. And If I do that, it freezes at the DFT-logo...
Click to expand...
Click to collapse
you must put your rom.zip to sd root, not unzipped files. but that doesn't work if you cannot go to ad recovery menu.
as a last chance can you format your sd card using panasonic sd formatter,then flash recovery partition, then see if recovery menu comes.
mutil said:
you must put your rom.zip to sd root, not unzipped files. but that doesn't work if you cannot go to ad recovery menu.
as a last chance can you format your sd card using panasonic sd formatter,then flash recovery partition, then see if recovery menu comes.
Click to expand...
Click to collapse
Did that now, formattet SD card with panasonic sd formatter, flashed the recovery you sent me, and then try to enter ad recovery. This shows up:
ANDROID LOAD RAW
[K]1180800:2B78E8 12800000:22FDEF 11800100
Load done!
123456
GO GO GO!
Nothing more!
abbamust said:
Did that now, formattet SD card with panasonic sd formatter, flashed the recovery you sent me, and then try to enter ad recovery. This shows up:
ANDROID LOAD RAW
[K]1180800:2B78E8 12800000:22FDEF 11800100
Load done!
123456
GO GO GO!
Nothing more!
Click to expand...
Click to collapse
i'll just get crazy.
now we'll try going to recovery by sd method. download the attached file, unrar it.put the extracted folder to sd card.
in mgldr go to services-boot settings-ad sd dir-find our folder in list and choose-you'll go to mgldr menu automatically.now choose 2nd choice ad sd.this must send you to recovery menu.then install your rom.zip following instructions in former posts.
Hi,
I keep having problems every time installing a Nana Android on my HD2.
I have looked at Installing for Newbies but keeps giving me error messages.
I have gone back to Stock Win Mobile 6.5 as I'm having troubles.
Can someone help me?
xda_apprentice said:
Hi,
I keep having problems every time installing a Nana Android on my HD2.
I have looked at Installing for Newbies but keeps giving me error messages.
I have gone back to Stock Win Mobile 6.5 as I'm having troubles.
Can someone help me?
Click to expand...
Click to collapse
First of all calm down mate... dont get nervous,
You need to be more specific with the error thing you are telling us..so we can help you
So plz provide us with more info about the error you are getting and when you are getting it(on which step of the nand setup).
Dakargr said:
First of all calm down mate... dont get nervous,
You need to be more specific with the error thing you are telling us..so we can help you
So plz provide us with more info about the error you are getting and when you are getting it(on which step of the nand setup).
Click to expand...
Click to collapse
Thanks for your reply.
I am back on Win Mobile 6.5. I want this rom :
http://forum.xda-developers.com/showthread.php?t=1264828
I read 'Install nand for Newbie' but happened was I used HTC HD2 Tool kit to:
Wipe29, install Magldr, install Radio butit made stuck in HTC Screen.
Where am I going wrong?
xda_apprentice said:
Thanks for your reply.
I am back on Win Mobile 6.5. I want this rom :
http://forum.xda-developers.com/showthread.php?t=1264828
I read 'Install nand for Newbie' but happened was I used HTC HD2 Tool kit to:
Wipe29, install Magldr, install Radio butit made stuck in HTC Screen.
Where am I going wrong?
Click to expand...
Click to collapse
So from what you stated here you Task29, MAGLDR, Radio (which one byt the way) but did you install Clockworkmod recovery? If you have done nothing then that's why you are stuck at HTC screen as you have no OS or anything loaded yet. MAGLDR is the only thing you have installed.
From your steps you then need to:
1. Install the appropriate recovery (which I and another user had linked you to in another one of your posts)
2. Boot into MAGLDR (by holding power button) and then boot into CWM recovery
3. Partition your sdcard with your desired size (512-1024mb respectively but do not forget to backup the contents of your sdcard as partitioning will format it)
4. Transfer the rom you want to your sdcard
5. Flash it from CWM recovery
6. Reboot
7. Enjoy Nand android build and go have a donut
Post if you have additional questions
chrisrj28 said:
So from what you stated here you Task29, MAGLDR, Radio (which one byt the way) but did you install Clockworkmod recovery? If you have done nothing then that's why you are stuck at HTC screen as you have no OS or anything loaded yet. MAGLDR is the only thing you have installed.
From your steps you then need to:
1. Install the appropriate recovery (which I and another user had linked you to in another one of your posts)
2. Boot into MAGLDR (by holding power button) and then boot into CWM recovery
3. Partition your sdcard with your desired size (512-1024mb respectively but do not forget to backup the contents of your sdcard as partitioning will format it)
4. Transfer the rom you want to your sdcard
5. Flash it from CWM recovery
6. Reboot
7. Enjoy Nand android build and go have a donut
Post if you have additional questions
Click to expand...
Click to collapse
I'll just keep my Doughnut to the side until I install Android
3) How do I back it up? And how do I know what size 512 or 1024?
I'll do the above steps and will report back.
P.s. I am on Stock Windows Mobile 6.5.
xda_apprentice said:
I'll just keep my Doughnut to the side until I install Android
3) How do I back it up? And how do I know what size 512 or 1024?
I'll do the above steps and will report back.
P.s. I am on Stock Windows Mobile 6.5.
Click to expand...
Click to collapse
Nice haha,
Anyway by backup your sdcard I mean save whatever is on the card (music, pictures, etc.) to your computer, that way you can copy it back to the card after you have everything set up
As for what size to partition your sdcard, it's up to you. That partition space is the size of memory you will have to install user apps so it depends on how many you plan on using
When you make it to recovery you will see the option to partition your card, it will take you through the process.
chrisrj28 said:
Nice haha,
Anyway by backup your sdcard I mean save whatever is on the card (music, pictures, etc.) to your computer, that way you can copy it back to the card after you have everything set up
As for what size to partition your sdcard, it's up to you. That partition space is the size of memory you will have to install user apps so it depends on how many you plan on using
When you make it to recovery you will see the option to partition your card, it will take you through the process.
Click to expand...
Click to collapse
This is what I did:
1)first get the recommended radio:2.15.50.14
2)download and install the nand tool kit
3)be sure you have hspl 2.08
4) go to bootloader screen(tri-color screen)
5)connect phone to pc ,see 'usb' at bottom
6)in toolkit click task29
7)go to bootloader again
8)in toolkit at bottom click browse and find your radio(2.15.50.14) click install ruu
9)go bootloader again
10)click install mgldr
11)in toolkit at left choose 150 and write 5 instead of 45
After step 11, I got this message:
"An error has occurred
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (736) "
My usb is clearly connected. This happened before too.
xda_apprentice said:
This is what I did:
1)first get the recommended radio:2.15.50.14
2)download and install the nand tool kit
3)be sure you have hspl 2.08
4) go to bootloader screen(tri-color screen)
5)connect phone to pc ,see 'usb' at bottom
6)in toolkit click task29
7)go to bootloader again
8)in toolkit at bottom click browse and find your radio(2.15.50.14) click install ruu
9)go bootloader again
10)click install mgldr
11)in toolkit at left choose 150 and write 5 instead of 45
After step 11, I got this message:
"An error has occurred
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (736) "
My usb is clearly connected. This happened before too.
Click to expand...
Click to collapse
Ok after step 10 installing MAGLDR you should boot into the MAGLDR screen. Select the USB Flasher option, instead of using the Nand toolkit try downloading the recovery here: http://forum.xda-developers.com/attachment.php?attachmentid=729033&d=1316816787
and using the daf.exe try flashing it that way. Make sure MAGLDR is in USB flasher selection.
chrisrj28 said:
Ok after step 10 installing MAGLDR you should boot into the MAGLDR screen. Select the USB Flasher option, instead of using the Nand toolkit try downloading the recovery here: http://forum.xda-developers.com/attachment.php?attachmentid=729033&d=1316816787
and using the daf.exe try flashing it that way. Make sure MAGLDR is in USB flasher selection.
Click to expand...
Click to collapse
It says " Please waiting .."
But it's been doing that for 20 minutes now
I meant stuck on HTC Quietly Brilliant Screen"
xda_apprentice said:
It says " Please waiting .."
But it's been doing that for 20 minutes now
I meant stuck on HTC Quietly Brilliant Screen"
Click to expand...
Click to collapse
WHich part says please wait? When you installed MAGLDR your computer installed the drivers for it correct?
chrisrj28 said:
WHich part says please wait? When you installed MAGLDR your computer installed the drivers for it correct?
Click to expand...
Click to collapse
Yea all the drivers were correct. It just keeps looping into that screen "HTC Quietly Brilliant Screen"
xda_apprentice said:
Yea all the drivers were correct. It just keeps looping into that screen "HTC Quietly Brilliant Screen"
Click to expand...
Click to collapse
Ok so did you successfully flash the CWM recovery?
chrisrj28 said:
Ok so did you successfully flash the CWM recovery?
Click to expand...
Click to collapse
This is what I exactly did:
1)first get the recommended radio:2.15.50.14
2)download and install the nand tool kit
3)be sure you have hspl 2.08
4) go to bootloader screen(tri-color screen)
5)connect phone to pc ,see 'usb' at bottom
6)in toolkit click task29
7)go to bootloader again
8)in toolkit at bottom click browse and find your radio(2.15.50.14) click install ruu
9)go bootloader again
10)click install mgldr *Used the file you supplied
11)in toolkit at left choose 150 and write 5 instead of 45 *could not do this as I got error msg
12)in mgldr menu go to usb flasher. be sure you see usb flasher....usb. if not change usb port etc.
13)in toolkit click repartition. be sure at left top mgldr repartition is chosen.
14) this operation will wipe your sd !!!when it finishes,in mgldr go ad recovery-advanced-partition sd card-1024-0 (so you'll have 1 gb sd-ext partition)
15) in mgldr-ad recovery-mounts and storage-mount usb storage-when pc sees phone send your downloaded rom.zip to sd
16)in mgldr: ad recovery-install zip from sd-choose zip from sd-find your rom.zip and choose it with call button.
17)after installation is complete reboot
xda_apprentice said:
This is what I exactly did:
1)first get the recommended radio:2.15.50.14
2)download and install the nand tool kit
3)be sure you have hspl 2.08
4) go to bootloader screen(tri-color screen)
5)connect phone to pc ,see 'usb' at bottom
6)in toolkit click task29
7)go to bootloader again
8)in toolkit at bottom click browse and find your radio(2.15.50.14) click install ruu
9)go bootloader again
10)click install mgldr *Used the file you supplied
11)in toolkit at left choose 150 and write 5 instead of 45 *could not do this as I got error msg
12)in mgldr menu go to usb flasher. be sure you see usb flasher....usb. if not change usb port etc.
13)in toolkit click repartition. be sure at left top mgldr repartition is chosen.
14) this operation will wipe your sd !!!when it finishes,in mgldr go ad recovery-advanced-partition sd card-1024-0 (so you'll have 1 gb sd-ext partition)
15) in mgldr-ad recovery-mounts and storage-mount usb storage-when pc sees phone send your downloaded rom.zip to sd
16)in mgldr: ad recovery-install zip from sd-choose zip from sd-find your rom.zip and choose it with call button.
17)after installation is complete reboot
Click to expand...
Click to collapse
Alright so you successfully booted into CWM recovery and flashed the Rom and it boot loops correct?
chrisrj28 said:
Alright so you successfully booted into CWM recovery and flashed the Rom and it boot loops correct?
Click to expand...
Click to collapse
Yes. It just loops and nothing happens
xda_apprentice said:
Yes. It just loops and nothing happens
Click to expand...
Click to collapse
Ok, boot back into MAGLDR and select USB Flasher again. Download the attached CWM Partition which I edited to 180mb partition. Click the Daf.exe and let it install. Then go to AD Recovery and flash the rom again, let me know how that works. (make sure your sdcard is already partitioned properly
chrisrj28 said:
Ok, boot back into MAGLDR and select USB Flasher again. Download the attached CWM Partition which I edited to 180mb partition. Click the Daf.exe and let it install. Then go to AD Recovery and flash the rom again, let me know how that works. (make sure your sdcard is already partitioned properly
Click to expand...
Click to collapse
I done everything as stated above. It says "Please wait ... Installing"
Then I see custom "HTC Quietly Brilliant"
And you guessed it ... it's looping
Is the rom? I did look at the website for the rom and it doesn't say anything
xda_apprentice said:
I done everything as stated above. It says "Please wait ... Installing"
Then I see custom "HTC Quietly Brilliant"
And you guessed it ... it's looping
Is the rom? I did look at the website for the rom and it doesn't say anything
Click to expand...
Click to collapse
Ok there is something being missed here. The please wait, installing part is the MAGLDR portion correct?
chrisrj28 said:
Ok there is something being missed here. The please wait, installing part is the MAGLDR portion correct?
Click to expand...
Click to collapse
How do I check/change that?
xda_apprentice said:
How do I check/change that?
Click to expand...
Click to collapse
Ok lets start from the beginning, post what you actually did step by step.