Database Users

[Q] stock rom flash fail

Hello,
-sorry for my english I dont speak well but...
phone: I9505
I was testing cyanogemod 10.1.3 for a while but then I decided get back to stock rom, did full wipe and put this ROM I9505XXUBMF8 into Odin and start flashing but he said this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-then I couldnt go to system, recovery just to download mode so I flashed TWRP.
(I tried another stock rom, odin, PC but always same problem.)
-then i tried get back CM 10.1.3 via TWRP and it flashed and work without problem.
-then I tried flash omega rom via TWRP and it flashed without problem but booting is very slow and during the logo Samsung it takes about 10mins to boot into system and device is very hot.
-Everything about Kies and antivirus is off.
-Using just original USB cable.
-what says download mode:
ODIN MODE
PRODUCT NAME: gt-i9505
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X1
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION: ENABLED
START [224, 1440]
SW REV, CHECK FAIL : FUSED : 2 , BINARY : 1
Any ideas how to resolve this?
Thank you

you have a secured bootloader, you can not flash old firmwares, flash MH8
use search button, there is a lot of threads talking about this issue

samersh72 said:
you have a secured bootloader, you can not flash old firmwares, flash MH8
use search button, there is a lot of threads talking about this issue
Click to expand...
Click to collapse
Thank you so much, I was looking for something all day but i didnt sure what Im really looking for

Need a TWRP Recovery MD5/WIN.000

Hello, everyone!
I recently have run into some trouble with my (ATT) Galaxy S4 (SGH-I337). I flashed a custom rom and (idiotically) didn't make a backup. Long story short, things didn't quite work out with the new rom. I didn't like it, and I wanted to go back to the old stock firmware. So I decided I would try to do it. I tried flashing with odin, using recovery, etc. Nothing worked so far. I've been researching for about 12 hours now. I think I know what I need. I need a TWRP backup, so that I can move it to the sd, and trick twrp into thinking I backed up my system so I can restore it. Below, I will link a post to what I want. The reason I can't use the below is because it's for a different carrier. If someone would be kind enough to link me something, that would be great. Again, my phone is a ATT Galaxy S4 (SGH-I337). Please help me out!
http://forum.xda-developers.com/showthread.php?t=2506562

Before I help you I want to be absolutely sure.
Are you sure you have an i9505? Because you keep saying ATT. That's a completely different phone. That's the SGH-I337. You can't flash stuff for the i9505 on the SGH-I337.
So what model do you have? Do you have an i9505 or the SGH-I337. My guess would be that you have the SGH-I337.
ps I have no idea what the thread is what you posted. Don't use that thread because its outdated.

Lennyz1988 said:
Before I help you I want to be absolutely sure.
Are you sure you have an i9505? Because you keep saying ATT. That's a completely different phone. That's the SGH-I337. You can't flash stuff for the i9505 on the SGH-I337.
So what model do you have? Do you have an i9505 or the SGH-I337. My guess would be that you have the SGH-I337.
ps I have no idea what the thread is what you posted. Don't use that thread because its outdated.
Click to expand...
Click to collapse
Yes, then I have an SGH-I337.

Lennyz1988 said:
Before I help you I want to be absolutely sure.
Are you sure you have an i9505? Because you keep saying ATT. That's a completely different phone. That's the SGH-I337. You can't flash stuff for the i9505 on the SGH-I337.
So what model do you have? Do you have an i9505 or the SGH-I337. My guess would be that you have the SGH-I337.
ps I have no idea what the thread is what you posted. Don't use that thread because its outdated.
Click to expand...
Click to collapse
Since I did in fact flash the wrong ROM, could I just reflash a new ROM that's compatible with my phone?

dillondonnelly1 said:
Since I did in fact flash the wrong ROM, could I just reflash a new ROM that's compatible with my phone?
Click to expand...
Click to collapse
Yes. You can flash a stock rom for your device.

Lennyz1988 said:
Yes. You can flash a stock rom for your device.
Click to expand...
Click to collapse
Alright, but for some reason I get an error in Odin. It says "SECURE CHECK FAIL". Do you have any idea what might cause this?

dillondonnelly1 said:
Alright, but for some reason I get an error in Odin. It says "SECURE CHECK FAIL". Do you have any idea what might cause this?
Click to expand...
Click to collapse
You need to give way more details.
- Post the complete log here.
- What are you trying to flash?
- What is your bootloader?

Lennyz1988 said:
You need to give way more details.
- Post the complete log here.
- What are you trying to flash?
- What is your bootloader?
Click to expand...
Click to collapse
- Post the complete log here.
Odin Log:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004>
<ID:0/004> Receive Response from boot-loader
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone Log:
Product Name: SGH-I337
CURRENT BINARY: Samsung Official
KNOX KERNAL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
Write PROTECTION: Enable
eMMC BURST MODE enabled
START [224,1440]
SW REV. CHECK FAIL : fused : 5 , Binary : 1
- What are you trying to flash? I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 (Stock ROM)
-What is your bootloader? (Safestrap)
Also, the firmware came with a SS_DL.dll file. Do I do anything with this file?

Odin won't flash?
Here are the logs. I'm trying to flash the stock firmware with odin, because currently, there is no rom on my device. I have an ATT SGH-I337. Please help.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004>
<ID:0/004> Receive Response from boot-loader
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone Log:
Product Name: SGH-I337
CURRENT BINARY: Samsung Official
KNOX KERNAL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
Write PROTECTION: Enable
eMMC BURST MODE enabled
START [224,1440]
SW REV. CHECK FAIL : fused : 5 , Binary : 1

Its probably because you are flashing an old firmware on your new bootloader. What version where you previously on? 4.4.2? Then you can't flash a 4.2.2 rom.
ps stop opening new threads for this. You already got this thread.

Lennyz1988 said:
Its probably because you are flashing an old firmware on your new bootloader. What version where you previously on? 4.4.2? Then you can't flash a 4.2.2 rom.
ps stop opening new threads for this. You already got this thread.
Click to expand...
Click to collapse
Please tell me exactly what to do. I have to get my phone fixed by tonight.

dillondonnelly1 said:
Here are the logs. I'm trying to flash the stock firmware with odin, because currently, there is no rom on my device. I have an ATT SGH-I337. Please help.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004>
<ID:0/004> Receive Response from boot-loader
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone Log:
Product Name: SGH-I337
CURRENT BINARY: Samsung Official
KNOX KERNAL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
Write PROTECTION: Enable
eMMC BURST MODE enabled
START [224,1440]
SW REV. CHECK FAIL : fused : 5 , Binary : 1
Click to expand...
Click to collapse
Hi mate ,
check if
Odin troubleshooting: If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver
Thanks to @samersh72
what software a re you flashing ? if you try to flash an older bootloader Odin will not allowed

[Help] My Phone won't boot (Samsung Galaxy S4)

Hi guys, i been searching for long time to resolve my issue and nothing found i think you guys could help me.
The issue is
My phone was rooted - Samsung Galaxy S4 - GT-I9505
And then i unrooted, but nothing to do with this, it was all oK..
After that i tried to upgrade the firmware from sammobile something like that..
I downloaded the new firmware I9505XXUGNG8_I9505MAXGNG1_I9505XXUGNG8_HOME.tar for my phone
And in the end of the line using Odin i got FAILED red box.. And since that i can't boot my phone stuck at Odin Mode: Firmware upgrade encountered an issue. Please select recovery mode in Kies & Try again. And up with small text says: Odin Mode, PRODUCT NAME: GT-19505, CURRENT BINARY: costum, SYSTEM STATUS: costum, KNOX KERNEL LOCK: 0x0, KNOX WARRANTY VOID: 0x1, CS0-CONFIG-LS8: 0x30, WRITE PROTECTION: enable, eMMc BURST MODE: enable
i tried with Kies but i can't connect , because i think after i unrooted, i reset my phone so USB debugging is not checked. I think for that. So i'm trying to install new firmwares with Odin and is not working i always get fail message red box, i tried all versions.
Does anyone know what to do please.
i Appreciate it.
Thanks.

GoodMan14 said:
Hi guys, i been searching for long time to resolve my issue and nothing found i think you guys could help me.
The issue is
My phone was rooted - Samsung Galaxy S4 - GT-I9505
And then i unrooted, but nothing to do with this, it was all oK..
After that i tried to upgrade the firmware from sammobile something like that..
I downloaded the new firmware I9505XXUGNG8_I9505MAXGNG1_I9505XXUGNG8_HOME.tar for my phone
And in the end of the line using Odin i got FAILED red box.. And since that i can't boot my phone stuck at Odin Mode: Firmware upgrade encountered an issue. Please select recovery mode in Kies & Try again. And up with small text says: Odin Mode, PRODUCT NAME: GT-19505, CURRENT BINARY: costum, SYSTEM STATUS: costum, KNOX KERNEL LOCK: 0x0, KNOX WARRANTY VOID: 0x1, CS0-CONFIG-LS8: 0x30, WRITE PROTECTION: enable, eMMc BURST MODE: enable
i tried with Kies but i can't connect , because i think after i unrooted, i reset my phone so USB debugging is not checked. I think for that. So i'm trying to install new firmwares with Odin and is not working i always get fail message red box, i tried all versions.
Does anyone know what to do please.
i Appreciate it.
Thanks.
Click to expand...
Click to collapse
Hi mate ,
You have to flash an stock rom with odin , there is no other solution
Check this thread , i will give you in detail how to proceed
http://forum.xda-developers.com/showthread.php?t=2265477

MAX 404 said:
Hi mate ,
You have to flash an stock rom with odin , there is no other solution
Check this thread , i will give you in detail how to proceed
http://forum.xda-developers.com/showthread.php?t=2265477
Click to expand...
Click to collapse
That's what he's doing. It should be working.
It MIGHT be because you have non official firmware on it now and it's not accepting the flash back to stock. IF that's the case the solution is to uncheck auto reboot in Odin and run the install sequence twice in a row. That's worth a shot here, but I don't think it's the solution.
Do you still have a working custom recovery? If so you should still be able to flash a custom ROM. I might try flashing a custom TouchWiz rom then starting over.

Still fail !
ty for reply guys, ok i captured everything
this is image when i browse the file on AP / PDA odin freezed for few seconds...
And this is what i got:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUGNG8_I9505MBMGNG1_I9505XXUGNG8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!

GoodMan14 said:
ty for reply guys, ok i captured everything
this is image when i browse the file on AP / PDA odin freezed for few seconds...
And this is what i got:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUGNG8_I9505MBMGNG1_I9505XXUGNG8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Click to expand...
Click to collapse
Hi ,
This is from the post i gave you earlier
Odin troubleshooting: If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver.
- Use pit file.
- Try another computer.
Check and see if it helps , did you try what Skipjacks said?

i di all
Hi, in this morning i tried again and passed.. finally
Thanks for helping.

GoodMan14 said:
Hi, in this morning i tried again and passed.. finally
Thanks for helping.
Click to expand...
Click to collapse
Great news mate
Sent from my Nexus 7 using XDA Premium 4 mobile app

Try flash stock firmware using odin

Help flashing stock firmware

I am a noob at this, so pardon me for my ignorance. After unrooting my Note 3 i am unable to update my firmware OTA or with Kies, even after factory resetting it did not work. After doing some research i learned that i have to flash my phone with stock firmware using odin(in order to get my phone back to normal). Do i have to flash the original firmware that my phone came with, or can i just flash it with the most up to date stock firmware that i want?

Jaxxxed said:
I am a noob at this, so pardon me for my ignorance. After unrooting my Note 3 i am unable to update my firmware OTA or with Kies, even after factory resetting it did not work. After doing some research i learned that i have to flash my phone with stock firmware using odin(in order to get my phone back to normal). Do i have to flash the original firmware that my phone came with, or can i just flash it with the most up to date stock firmware that i want?
Click to expand...
Click to collapse
You can flash the same build fw or the latest. Install 'samsung phone info' app to check your csc. You can even use the app to download the fw. But in case downloading takes forever to complete, you may use 'samsung firmware downloader'. It's a windows utility tool to download fw from sammobile.
Sent from my SM-N920C

When i attempted to use Odin, the flashing failed. here is the Odin log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone still works fine, and i have everything set up properly so that my phone can be flashed. so, im not sure whats going wrong.

Jaxxxed said:
When i attempted to use Odin, the flashing failed. here is the Odin log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone still works fine, and i have everything set up properly so that my phone can be flashed. so, im not sure whats going wrong.
Click to expand...
Click to collapse
It's N900?. Try different fw.
In download mode does it show reactivation lockn?
Sent from my SM-N920C

Rosli59564 said:
It's N900?. Try different fw.
In download mode does it show reactivation lockn?
Sent from my SM-N920C
Click to expand...
Click to collapse
Here is what my phone says in download mode:
Odin Mode
Product name: SM-N900A
Current Binary: Samsung official
System status: custom
Knox kernel lock: 0x0
Knox warranty void: 0x0
Qualcomm Secure boot: enable(csb)
RP SWREV: S2, T2, A2, A2, P2
Write protection:enable

The n900a is an att note 3.

Soft Bricked and Odin stuck?

I tried installing a custom ROM on my Galaxy J5 SM-j500FN but i got stuck for about 3 hours on the samsung blinking logo so i decided to flash the stock ROM again. After downloading it and trying to flashing via ODIN I keep getting the same error over and over.
Error on ODIN:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1203)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Error on the Download mode in the phone:
ODIN MODE
PRODUCT NAME: SM-J500FN
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
FRP LOCK: OFF
WARRANTY VOID: 0x1 (1)
QUALCOMM SECUREBOOT: ENABLE (CSB)
AP SWREV: S1, T1, H1, R1, A1, P1
SECURE DOWNLOAD: ENABLE
SECURE CHECK FAIL : aboot
Any kind of help is appreciated. Thanks in advance for every reply!

Tenebrific said:
I tried installing a custom ROM on my Galaxy J5 SM-j500FN but i got stuck for about 3 hours on the samsung blinking logo so i decided to flash the stock ROM again. After downloading it and trying to flashing via ODIN I keep getting the same error over and over.
Error on ODIN:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1203)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Error on the Download mode in the phone:
ODIN MODE
PRODUCT NAME: SM-J500FN
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
FRP LOCK: OFF
WARRANTY VOID: 0x1 (1)
QUALCOMM SECUREBOOT: ENABLE (CSB)
AP SWREV: S1, T1, H1, R1, A1, P1
SECURE DOWNLOAD: ENABLE
SECURE CHECK FAIL : aboot
Any kind of help is appreciated. Thanks in advance for every reply!
Click to expand...
Click to collapse
I went through this model, but the model is the J500M.
After spending all day trying, late in the afternoon I ended up deciding to change the USB cables.
I tried 5 different ones being one of them that came with the ...
I got it with an old motorola cable ... lol
After that I also changed a stock rom because one that I had downloaded was from another version of J500M
Another thing I noticed is that at least in my device, after installing the rom stock I can not do root in it anymore.
I can install TWRP but when installing SuperUser it stays on this screen by running only the logo intermittently = x
I'm looking for a solution to this yet ...

Go to developers options in setting and click on OEM unlock then flash

It its stock no need to enable oem
Sent from my SM-J500F using Tapatalk

Tenebrific said:
I tried installing a custom ROM on my Galaxy J5 SM-j500FN but i got stuck for about 3 hours on the samsung blinking logo so i decided to flash the stock ROM again. After downloading it and trying to flashing via ODIN I keep getting the same error over and over.
Error on ODIN:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1203)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Error on the Download mode in the phone:
ODIN MODE
PRODUCT NAME: SM-J500FN
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
FRP LOCK: OFF
WARRANTY VOID: 0x1 (1)
QUALCOMM SECUREBOOT: ENABLE (CSB)
AP SWREV: S1, T1, H1, R1, A1, P1
SECURE DOWNLOAD: ENABLE
SECURE CHECK FAIL : aboot
Any kind of help is appreciated. Thanks in advance for every reply!
Click to expand...
Click to collapse
This error usually pops up when the firmware image you are flashing is for another phone's model/variant instead. Could you pop off the battery and have a look at the sticker for your model and verify that it is correct?

Hi, I have j510fn and I was a rom tester,
I have a problem since I flashed
J510FNXXU2APK6_J510FNODD2APK2_J510FNXXU2APK2_HOME.tar.md5
to test light stock rom v3 from Kingraheel
what happens is that NOW I can't flash any other firmware by odin... when I click START it says FAIL and in my device there is this text in red
SW REV CHECK FAIL : [aboot]Fused 2 > Binary 1
I just want to flash my OFFICIAL firmware
J510FNXXU1APG1_J510FNPHE1APG1_J510FNXWU1APFC_HOME.tar.md5
but I can't... only APK6 firmware works on odin... any other firmware works.... can you help me?
I don't have any NANDROID backup of previous versions... only of my actual firmware... APK6
My computer does not detect my device... I have the drivers installed, and I tried on all the USB ports... it charges but not open files.... PLEASE HELP
---------------------------------------
SOLVED, SAME PROBLEM? CONTACT ME

Here is HOW I SOLVED IT:
This error happens when you before have updated from "U1" to "U2" and then you try to flash a firmware with "U1" (UX appears in the firmware "name")
So, the simple solution is to flash the stock firmware with the same "UX" that you had before your device gor bricked.
In my case, testing KingRaheel's ROMS I flashed an Indian firmware (...U2APK6...) at this moment I didn't know I ****ed up. But don't worry, I simply had updated the "U" and how I didn't know it, I tried to flash lots and lots of firmwares with "U1" without knowing what was happening. After long nights, I tried to flash my last firmware from SPAIN (PHE) with "U2" and it worked.
I hope I helped you. I used SM-J510FN (J5 2016)
If you have another device, try the same but with your current model, any questions, ask by twitter/dm
Sent from my SM-J510FN using XDA Labs