[Q] Galaxy s4 GT-i9505 - Galaxy S 4 Q&A, Help & Troubleshooting

Hi Guys Hope you can rescue me. I had an automatic firmware update pending on my phone this morning so I ran it. It all seemed to go fine and it rebooted but I initially noticed that some desktop icons were missing. Then I noticed that you could not turn on wifi. I tried both from drop down and in settings but it would revert back to off each time. I googled it and found a few others had the problem and it was suggested that a hard reset may fix it. I did that but no joy.
Next step was to download odin 3.09 and a stock rom. This I did, the stock rom was a uko2 rom from here...hxxp://samsung-updates.com/latest-firmware/ I followed the tutorial to flash the rom and I get this (auth) Fail. here is a copy of the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK8_I9505O2UEMK1_I9505XXUEMK8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have searched on here and found some hits one was to load a pit file as well but it fails the same way the file I am loading is an MD5 file and I read somewhere it may have to be a ME7 file but I cant find that anywhere.Can some guru please help this frustrated user out as its doing my head in. Many thanks guys

If the OTA update received was android 4.4.2, maybe u updated your bootloader and you cant come back to android 4.3. You will have to flash through ODIN this firmware: HERE

Joku1981 said:
If the OTA update received was android 4.4.2, maybe u updated your bootloader and you cant come back to android 4.3. You will have to flash through ODIN this firmware: hxxp://rapidgator.net/file/e4df24422154b8c1320925eceb5d4f1f"]HERE
Click to expand...
Click to collapse
Thanks for this Joku1981. I am downloading it now and will update thread when I have tried it.

steve67474 said:
Thanks for this Joku1981. I am downloading it now and will update thread when I have tried it.
Click to expand...
Click to collapse
OK have downloaded and run the odin program it seemed to go fine but right at the endjust after the system load it failed again:crying: Here is the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505O2UFNA2_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> NON-HLOS.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/005> Added!!
Thought we cracked it

steve67474 said:
OK have downloaded and run the odin program it seemed to go fine but right at the endjust after the system load it failed again:crying: Here is the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505O2UFNA2_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> NON-HLOS.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/005> Added!!
Thought we cracked it
Click to expand...
Click to collapse
OK an update. I removed the battery for 5 mins and rerun and hey presto it worked. Great forum and thanks again for the support

Related

need help asap. cant reflash stock FW

i need help. i tried to flash a custom rom. it didnt work. so i thought go bad to stock. i have a i747 on rogers . odin3 keeps failing and im stumped. been googling all day and i cant figure it out can some help me please
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I747MVLALE8_I747MOYAALE8_20120523.225040 _REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Read ..
<ID:0/003> XmitData Fail..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
this is what i got
i got it finally. for some reason i had to take the .md5 off and just leave it .tar

[Q] Flash Stock Rom on Odin Fail

<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUGNH1_N9005OLBGNH1_N9005XXUGNH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Hi guys my phone having some boot loop issue after a OTA update, I downloaded the latest stock rom from sammobile and tried to flash via odin but keep getting fail after the modem.bin part, did I did something wrong?
kktan said:
Hi guys my phone having some boot loop issue after a OTA update, I downloaded the latest stock rom from sammobile and tried to flash via odin but keep getting fail after the modem.bin part, did I did something wrong?
Click to expand...
Click to collapse
Guys bad news, i went to service centre and they said my phone motherboard spoilt, need to pay RM870 to change to new motherboard as my warranty just finished last week! bad luck. I declined the offer and gonna try to flash the stock firmware myself.
Currently i still able to boot into my phone, but it will keep restarting suddenly, all sorts of goodleapps not working, samsung keyboard not working or go into infinite bootloop, is this hardware issue or software related more?
When the samsung keyboard failed, i cant key in anything at all, but im able to make call but i have no contact coz cant signin to google to retrieve my contacts.
I downloaded the latest rom from sammobile and tried to use odin to flash the stock firmware but it will fail with the this error after modem.bin
QUOTE
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUGNH1_N9005OLBGNH1_N9005XXUGNH1_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
looks like i might need to root the phone and try my luck on custom rom but i cant sign in to playstore to download certain app
any recommendation guys?
did you check the MD5 of the rom you dl???change ODIN version you use
for rooting your phone you don't need to dl files from market.. Use cf auto-root

[Q] Problems installing stock rom.

Hello, i update my samsung s5 SM-G900F to stock firmware - G900FXXU1BOA3_G900FOXA1BOA4_BTU
And now i cant install anything via Odin, just the same firmware. Cant install twrp or root, trying to install G900FDXU1BOA2_G900FOLB1BOA2_G900FDXU1BNL1 but i get error at the last sec.
Here's the log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900FDXU1BOA2_G900FOLB1BOA2_G900FDXU1BNL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
do i need to flash the pit file? can i do this while in G900FXXU1BOA3, or do i have to do it after failing G900FDXU1BOA2. And where can i find the right file.
gonna link the downloader mode error in a picture.
Help please :\

[Q] Soft Brick G900V

After owning the phone for a grand total of five minutes I managed to go past go and straight to a soft brick after a root-gone-wrong.
Out of the box it was running 4.4.4, but I don't know which of the three Verizon firmwares it was. I've attempted using Odin to flash stock using all three of them and I can't get Odin to play nicely.
The latest/greatest attempt was to flash \G900VVRU1ANK2_G900VVZW1ANK2_G900VVRU1ANK2_HOME.tar.md5. I'm getting the following Odin output:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900VVRU1ANK2_G900VVZW1ANK2_G900VVRU1ANK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm getting the same output regardless of which stock I'm trying to flash.
May I trouble you guys for some help?
... not that I expected it to work, but I tried the Verizon recovery software in a Windows VM. It seems great up until it hangs at 83% (repeatedly) before telling me the device has been disconnected. If anyone wants to try that rabbit hole, I'll get the precise error verbiage.
Selfish <bump>

Errors With Odin

I am trying to flash a stock rom on my Note 4 Exynos Version, with odin I have tried the latest version as well as some older ones. I have tried flashing both kit kat & lollipop but always get the same error. I have usb debugging ticked.
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
why is this happening?
Ta
Any help guys?
@home said:
Any help guys?
Click to expand...
Click to collapse
you are facing a locked bootloader as we all are (both exy and snap) the only solution to fix your bootloop is to install apps like phone info then find out what your phone PDA version is then find the exact PDA from Sammobile or if you you are Having an 910C flash latest COJ5 rom or if you are on 910H try installing COJ4 rom (just download and install the latest frimware from sammobile or ... and you will be just fine )
ArmanFGT said:
you are facing a locked bootloader as we all are (both exy and snap) the only solution to fix your bootloop is to install apps like phone info then find out what your phone PDA version is then find the exact PDA from Sammobile or if you you are Having an 910C flash latest COJ5 rom or if you are on 910H try installing COJ4 rom (just download and install the latest frimware from sammobile or ... and you will be just fine )
Click to expand...
Click to collapse
I followed your instructions and this is what I'm getting. Now what I need to do further? Previously I was using Sixperience ROM.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
sirius_gamer said:
I followed your instructions and this is what I'm getting. Now what I need to do further? Previously I was using Sixperience ROM.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
well , i dont really know what the XmitData_write is , as i havent seen it since my s4 (everything was fine) ..
i think wiping would solve the Prob...
or maybe USB cable or odin version (+drivers)
2. if nothing works around ... try using KIES emergency updating ... its always the sweety
odin3 v 3.12
i have same problem;
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
sdstc said:
odin3 v 3.12
i have same problem;
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
problem is using UN-OFFICIAL USB CABLE
use FACTORY CABLE FIXes problem
sdstc said:
problem is using UN-OFFICIAL USB CABLE
use FACTORY CABLE FIXes problem
Click to expand...
Click to collapse
@sdstc is right you can fix __XmitData_Write with changing the cable
i used an original sammy cable and it didnt work. than i used another sammy cable and then it just worked
my device was a Tab S btw no note 4 or s4
bu arada cok sagol sdstc kardes
TimurAlaskara_TR said:
@sdstc is right you can fix __XmitData_Write with changing the cable
i used an original sammy cable and it didnt work. than i used another sammy cable and then it just worked
my device was a Tab S btw no note 4 or s4
bu arada cok sagol sdstc kardes
Click to expand...
Click to collapse
i all the time face with that error and i forgot use original cable
(ne için teşekkür?)
sdstc said:
i all the time face with that error and i forgot use original cable
(ne için teşekkür?)
Click to expand...
Click to collapse
Sen olmasan telefon hala bozuktu cunku sjsjsj
help plz
sdstc said:
problem is using UN-OFFICIAL USB CABLE
use FACTORY CABLE FIXes problem
Click to expand...
Click to collapse
<OSM> Please wait..
<OSM> N910CXXS2DQG1_N910COXA2DPH1_N910CXXU1DPC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Categories

Resources