i need help. i tried to flash a custom rom. it didnt work. so i thought go bad to stock. i have a i747 on rogers . odin3 keeps failing and im stumped. been googling all day and i cant figure it out can some help me please
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I747MVLALE8_I747MOYAALE8_20120523.225040 _REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Read ..
<ID:0/003> XmitData Fail..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
this is what i got
i got it finally. for some reason i had to take the .md5 off and just leave it .tar
Related
Hi Guys Hope you can rescue me. I had an automatic firmware update pending on my phone this morning so I ran it. It all seemed to go fine and it rebooted but I initially noticed that some desktop icons were missing. Then I noticed that you could not turn on wifi. I tried both from drop down and in settings but it would revert back to off each time. I googled it and found a few others had the problem and it was suggested that a hard reset may fix it. I did that but no joy.
Next step was to download odin 3.09 and a stock rom. This I did, the stock rom was a uko2 rom from here...hxxp://samsung-updates.com/latest-firmware/ I followed the tutorial to flash the rom and I get this (auth) Fail. here is a copy of the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK8_I9505O2UEMK1_I9505XXUEMK8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have searched on here and found some hits one was to load a pit file as well but it fails the same way the file I am loading is an MD5 file and I read somewhere it may have to be a ME7 file but I cant find that anywhere.Can some guru please help this frustrated user out as its doing my head in. Many thanks guys
If the OTA update received was android 4.4.2, maybe u updated your bootloader and you cant come back to android 4.3. You will have to flash through ODIN this firmware: HERE
Joku1981 said:
If the OTA update received was android 4.4.2, maybe u updated your bootloader and you cant come back to android 4.3. You will have to flash through ODIN this firmware: hxxp://rapidgator.net/file/e4df24422154b8c1320925eceb5d4f1f"]HERE
Click to expand...
Click to collapse
Thanks for this Joku1981. I am downloading it now and will update thread when I have tried it.
steve67474 said:
Thanks for this Joku1981. I am downloading it now and will update thread when I have tried it.
Click to expand...
Click to collapse
OK have downloaded and run the odin program it seemed to go fine but right at the endjust after the system load it failed again:crying: Here is the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505O2UFNA2_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> NON-HLOS.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/005> Added!!
Thought we cracked it
steve67474 said:
OK have downloaded and run the odin program it seemed to go fine but right at the endjust after the system load it failed again:crying: Here is the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505O2UFNA2_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> NON-HLOS.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/005> Added!!
Thought we cracked it
Click to expand...
Click to collapse
OK an update. I removed the battery for 5 mins and rerun and hey presto it worked. Great forum and thanks again for the support
I wanted to update my samsung using odin when i tried it gave me this
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMJ5_I9505OJVEMJ5_I9505XXUEMJ5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
now im stuck at Emergency boot thing and it doesnt work
1. Try other USB ports, other pc or install again the Samsung drivers
2. This isn't the latest update anyway. It is: I9505XXUEMK9
Hi Guys
im Costum Rom Flashing Now Stock Rom Back But Rom Flashing System.img Fail
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9000QXXUENG4_N9000QTURENG3_N9000QJVUENG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This How Fix? Please Help Me!
Try to flash the latest firmware for your device: HERE.
xantiave said:
Hi Guys
im Costum Rom Flashing Now Stock Rom Back But Rom Flashing System.img Fail
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9000QXXUENG4_N9000QTURENG3_N9000QJVUENG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This How Fix? Please Help Me!
Click to expand...
Click to collapse
I'm not sure but maybe the custom rom has changed the partition structure?
If so you need the PIT file to flash with the stock firmware.
Hello, I update my samsung s5 SM-G900F to stock firmware - G900FXXU1BOA3_G900FOXA1BOA4_BTU
And now i cant install anything via Odin, just the same firmware. Cant install twrp or root, trying to install G900FDXU1BOA2_G900FOLB1BOA2_G900FDXU1BNL1 but i get error at the last sec.
Here's the log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900FDXU1BOA2_G900FOLB1BOA2_G900FDXU1BNL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Download Mode error in attached file
just installed G900FXXU1BOB7_G900FOXA1BOB7_BTU and it works as good as G900FXXU1BOA3.
is there any way to root G900FXXU1BOB7 ?
with autoroot i get failed. heres the log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-klte-kltexx-smg900f.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Help please :\
After owning the phone for a grand total of five minutes I managed to go past go and straight to a soft brick after a root-gone-wrong.
Out of the box it was running 4.4.4, but I don't know which of the three Verizon firmwares it was. I've attempted using Odin to flash stock using all three of them and I can't get Odin to play nicely.
The latest/greatest attempt was to flash \G900VVRU1ANK2_G900VVZW1ANK2_G900VVRU1ANK2_HOME.tar.md5. I'm getting the following Odin output:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900VVRU1ANK2_G900VVZW1ANK2_G900VVRU1ANK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm getting the same output regardless of which stock I'm trying to flash.
May I trouble you guys for some help?
... not that I expected it to work, but I tried the Verizon recovery software in a Windows VM. It seems great up until it hangs at 83% (repeatedly) before telling me the device has been disconnected. If anyone wants to try that rabbit hole, I'll get the precise error verbiage.
Selfish <bump>