This is a guide for those who are experiencing the problem 'There is no Pit Partition' while flashing with Odin. This problem may be caused because of a faulty USB/micro USB port, USB cable which results in connection problems during flashing. So first of all one should understand this process is Extremely Risky and should proceed only if its that much necessary.
For this process what you need is a PIT file for Galaxy Grand Duos i9082 and the original STOCK firmware. PIT (Partition Information Table) files provide information about where each partitions are to be flashed, so an improper PIT file will brick your phone permanently.
PIT file for Samsung Galaxy Grand Duos is provided in the attachment, and extract the .pit from the rar.
Follow these steps :
1. Run Odin with Administrator Privileges. Hope everyone is familiar with using Odin or See this
2.Connect your Galaxy Grand Duos I9082 inn Download Mode (HOLD Volume Down+Home Button+Power) and see phone gets detected by Odin.
3. Click on the PIT Button in Odin and select the .pit file you have downloaded.
4. Click on PDA, and Browse for the original Stock Firmware File of Samsung Galaxy Grand I9082.
5. Ensure that The Checkboxes Auto Reboot, Re-Partition, F. Reset Time are checked.
See This:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
6. Now Click Start
7. Wait for the process to complete, keep the phone untouched until you see PASS.
8. Switch ON the phone and Play!!
As this process is completely risky, DO THIS ONLY IF YOU KNOW WHAT YOU ARE DOING. DO IT IN YOUR OWN RISK!
Good Luck!!:good::good:
Press THANKS if I helped!
This is the pit which was bundled with leaked 4.2.2 update if I ain't wrong ?
Sent from my GT-I9082 using Tapatalk
akiratoriyama said:
This is the pit which was bundled with leaked 4.2.2 update if I ain't wrong ?
Sent from my GT-I9082 using Tapatalk
Click to expand...
Click to collapse
No Brother, its from B3 update JB 4.1.2
Hello,
I have a galaxy grand 2 sm-g7102 and a big problem.
What I need is just. Pit file for 7102nd When I did the update to a newer version of the process is broken.
Bootloader works, but Odin returns: There is no PIT partition.
I took several official version ROMs with sammobile.com, but when they unpacked find no pit file.
Please any help or ideas anyone?
Thanks in advance
Hope you can google n find out the .pit file for your galaxy grand 2. Do not go to download the full firmware.. Just search for the pit for your phone..
I could have provided that for you... But this is a new phone and i just dont have any idea, i mean NO idea about this phone and how the partitions are distributed.
If you cant find the pit file.. And you never tried to flash a custom rom, carry it to service centre.
Beware that you dont use pit file of any other device wid the device you have.
Good luck
Sent From GT-I9082
I tried following all of that and I always get this error:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
It's always failing for me. I tried installing 4.1.2 (I9082XXAMF5_I9082OLBAMG1_I9082XXAME2_HOME) rom for my GT-I9082. Any idea how to fix this? Please help me. I'm really desperate. Thank you.
Incohatus said:
I tried following all of that and I always get this error:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
It's always failing for me. I tried installing 4.1.2 (I9082XXAMF5_I9082OLBAMG1_I9082XXAME2_HOME) rom for my GT-I9082. Any idea how to fix this? Please help me. I'm really desperate. Thank you.
Click to expand...
Click to collapse
Has mentioned in OP if its Very much necessary than only u have to use PIT file...Why you want to use PIT file actually??
Incohatus said:
I tried following all of that and I always get this error:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
It's always failing for me. I tried installing 4.1.2 (I9082XXAMF5_I9082OLBAMG1_I9082XXAME2_HOME) rom for my GT-I9082. Any idea how to fix this? Please help me. I'm really desperate. Thank you.
Click to expand...
Click to collapse
Is it the full log of Odin which you can see in your computer. Are you sure that your phone is in download mode and got detected by Odin.
I cant see any Added cammand btw.
Sent from my GT-I9082 using XDA Premium 4 mobile app
DMJoh said:
Is it the full log of Odin which you can see in your computer. Are you sure that your phone is in download mode and got detected by Odin.
I cant see any Added cammand btw.
Sent from my GT-I9082 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Uhm it's not the full log. Yes my phone is detected. I'll try it again and post the full log.
---------- Post added at 02:31 PM ---------- Previous post was at 02:24 PM ----------
Here's the full log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMF5_I9082OLBAMG1_I9082XXAME2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Oh and by the way, I'm using Odin3 v. 3.09. Thanks for the help!
Incohatus said:
Uhm it's not the full log. Yes my phone is detected. I'll try it again and post the full log.
---------- Post added at 02:31 PM ---------- Previous post was at 02:24 PM ----------
Here's the full log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMF5_I9082OLBAMG1_I9082XXAME2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Oh and by the way, I'm using Odin3 v. 3.09. Thanks for the help!
Click to expand...
Click to collapse
Just change the USB cord and try again...
Sent from my GT-I9082 using XDA Premium 4 mobile app
Incohatus said:
Uhm it's not the full log. Yes my phone is detected. I'll try it again and post the full log.
---------- Post added at 02:31 PM ---------- Previous post was at 02:24 PM ----------
Here's the full log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMF5_I9082OLBAMG1_I9082XXAME2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Oh and by the way, I'm using Odin3 v. 3.09. Thanks for the help!
Click to expand...
Click to collapse
Use odin 3.07
Sent from my GT-I9082 using Tapatalk
Okay so I changed the USB cord and used Odin 3.07 but still, it gives me this error:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMF5_I9082OLBAMG1_I9082XXAME2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
. This is making me depressed.
Incohatus said:
Uhm it's not the full log. Yes my phone is detected. I'll try it again and post the full log.
---------- Post added at 02:31 PM ---------- Previous post was at 02:24 PM ----------
Here's the full log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMF5_I9082OLBAMG1_I9082XXAME2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Oh and by the way, I'm using Odin3 v. 3.09. Thanks for the help!
Click to expand...
Click to collapse
Its not necessary to use the PIT file, even if you use it, it wont affect, but i guess u never seen an error like NO PIT PARTITION, use .pit only if this shoes up. now the problem may be with USB cable, the micro USB port or USB port of your system. Try flashing from another system.
DMJoh said:
Its not necessary to use the PIT file, even if you use it, it wont affect, but i guess u never seen an error like NO PIT PARTITION, use .pit only if this shoes up. now the problem may be with USB cable, the micro USB port or USB port of your system. Try flashing from another system.
Click to expand...
Click to collapse
Actually that was the reason why I'm using a PIT file right now, because I'm encountering the "There is no partition" something like that, and that's how I end up with this article after searching it. So yeah. Is this still repairable? I've already tried different firmwares for GT-I9082 (4.1.2 and 4.2.2) but still it won't work.
Incohatus said:
Actually that was the reason why I'm using a PIT file right now, because I'm encountering the "There is no partition" something like that, and that's how I end up with this article after searching it. So yeah. Is this still repairable? I've already tried different firmwares for GT-I9082 (4.1.2 and 4.2.2) but still it won't work.
Click to expand...
Click to collapse
I feel its still repairable, i don't think its a brick. Okay if you ended up with the error THERE IS NO PIT PARTITION. That happened only because the flashing process got interrupted while flashing the PIT, the very first time. The interruption might have caused because of USB cable, the micro USB port of the phone (Highly Vulnerable) or the USB port of your PC. Have you ever experienced any problems while transferring data via USB??i had problem with my micro USB port of the phone, I ended up in the PIT issue. What I did was to keep the phone untouched and flashed the phone many times again and again.
Always you end up at the same point or sometimes in the middle of flashing?
DMJoh said:
I feel its still repairable, i don't think its a brick. Okay if you ended up with the error THERE IS NO PIT PARTITION. That happened only because the flashing process got interrupted while flashing the PIT, the very first time. The interruption might have caused because of USB cable, the micro USB port of the phone (Highly Vulnerable) or the USB port of your PC. Have you ever experienced any problems while transferring data via USB??i had problem with my micro USB port of the phone, I ended up in the PIT issue. What I did was to keep the phone untouched and flashed the phone many times again and again.
Always you end up at the same point or sometimes in the middle of flashing?
Click to expand...
Click to collapse
It's always at the same point. Here's the log when I'm not using PIT (this is also the same thing that happened as before):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMC7_I9082OJVAMC1_I9082XXAMC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I never had any problems on my USB port when transferring files. I always use the one that is directly connected at my motherboard (not using hubs for these kind of purposes).
Incohatus said:
It's always at the same point. Here's the log when I'm not using PIT (this is also the same thing that happened as before):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMC7_I9082OJVAMC1_I9082XXAMC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I never had any problems on my USB port when transferring files. I always use the one that is directly connected at my motherboard (not using hubs for these kind of purposes).
Click to expand...
Click to collapse
It might be issue with USB cable or USB port of mobile because i had similar Issue and ended with failure of flashing ...Could'nt Start my device then @DMJoh had said to change USB cable and I could flash Successfully but i could transfer the files withou any probs with usb cable but flashing still it fails....!
Incohatus said:
It's always at the same point. Here's the log when I'm not using PIT (this is also the same thing that happened as before):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXAMC7_I9082OJVAMC1_I9082XXAMC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I never had any problems on my USB port when transferring files. I always use the one that is directly connected at my motherboard (not using hubs for these kind of purposes).
Click to expand...
Click to collapse
Use Odin v3.07 itself.. There is chance that the NAND might be corrupted/damaged. I guess when you turn on your phone you get a warning like "Firmware Upgrade encountered an error, Please update using Kies" something like dat. If u hav a very high speed internet connection, see whether that method works.
Can you elaborate a bit about how these problems evolved. What happened the very first time when you attempted to flash, that particular attempt it went messy.
Sent from my GT-I9082 using XDA Premium 4 mobile app
DMJoh said:
Use Odin v3.07 itself.. There is chance that the NAND might be corrupted/damaged. I guess when you turn on your phone you get a warning like "Firmware Upgrade encountered an error, Please update using Kies" something like dat. If u hav a very high speed internet connection, see whether that method works.
Can you elaborate a bit about how these problems evolved. What happened the very first time when you attempted to flash, that particular attempt it went messy.
Sent from my GT-I9082 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Sorry for the late reply. I can't post a comment a while ago because it says on Captcha that my pc is sending automated queries. The first time I flashed my GT-I9082, it was actually quite successful. Quite because it says pass on Odin but it was stuck on a flashing "Samsung Galaxy Grand GT-I9082) and the guide I followed said that I should go into recovery mode but unfortunately I can't so I've read on another site that you can also just re-flash the firmware and so I did and that's how I got the "there is no partition".
Incohatus said:
Sorry for the late reply. I can't post a comment a while ago because it says on Captcha that my pc is sending automated queries. The first time I flashed my GT-I9082, it was actually quite successful. Quite because it says pass on Odin but it was stuck on a flashing "Samsung Galaxy Grand GT-I9082) and the guide I followed said that I should go into recovery mode but unfortunately I can't so I've read on another site that you can also just re-flash the firmware and so I did and that's how I got the "there is no partition".
Click to expand...
Click to collapse
It is evident that the flashing was not complete since you cant go to recovery and thus made the Pit error. There is a chance your NAND may be bricked. No need to panic, just try flashing.. If luck favours!!
Sent from my GT-I9082 using XDA Premium 4 mobile app
Related
Hi all,
i tried to flash cyanogenmod unofficial, on the flash an error was comming, now the device dosent start...
when i boot the phone normaly, is comming: firmware upgrade encountered an issue. please select recovery mode in kies & try again.
i tryed to flash the original firmware:
(I9505XXUAMDF_I9505AUTAMD8_AUT)
I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar
but an error in odin is comming:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Removed!!
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
please can you help me?
cutalaxy said:
Hi all,
i tried to flash cyanogenmod unofficial, on the flash an error was comming, now the device dosent start...
when i boot the phone normaly, is comming: firmware upgrade encountered an issue. please select recovery mode in kies & try again.
i tryed to flash the original firmware:
(I9505XXUAMDF_I9505AUTAMD8_AUT)
I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar
but an error in odin is comming:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Removed!!
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
please can you help me?
Click to expand...
Click to collapse
Try flashing along with pit file
MKe sure u have the proper file for the same
Sent from my GT-I9500 using xda premium
123hiten said:
Try flashing along with pit file
MKe sure u have the proper file for the same
Sent from my GT-I9500 using xda premium
Click to expand...
Click to collapse
where can i find the pit file?
cutalaxy said:
where can i find the pit file?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2265477&highlight=stock+firmware
this link has it attached take the correct one u would know better
dont worry i had the same issue on my note 2 a month ago and was wrkng fine after flashing rescue firmware urs wil work too
damn, it doeset work for me
is it hard brick?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
cutalaxy said:
damn, it doeset work for me
is it hard brick?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Click to expand...
Click to collapse
No its not at a hard brick dont worry dont panic thats the best wat to work around
I would say dont use pit file unless its last option and try without that only may be in other pc using other cable some below steps myte also help u
2) Install later Kies.
3) Kill al kies applications (all 4 of them).
disable antivirus or whatever you got there.) Get to Download Mode and push Vol Up.
7) Open Odin.
8) Plug the device to your laptop.
Does it see the device?
If NO:
A) Get another usb cable, are you using ?
B) Try different Odin Versions (download 3 or 4).
C) Try another USB port.
D) Still no luck? reboot the pc and start from step 3.
---------- Post added at 08:30 PM ---------- Previous post was at 08:23 PM ----------
Download 2/3 stock firmware and try installing thru ODIN it should work
Make sure u have all the drivers installed
MAke sure kies is not open or make sure its closed even in background process
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
cutalaxy said:
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
Click to expand...
Click to collapse
Official firmware is not a wiping one. It doesnt flash userdata, it replace system, recovery, and some other partitions.
sent from my Galaxy
cutalaxy said:
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
Click to expand...
Click to collapse
Great to hear that man
If u flash stock firmware all will remain as its in ODIN but its good if u reset the device after or b4 root
Also take a EFS backup of ur device and be safe
i had root before the device bricks... so i rootet it now again, and works good...
yeah, i will backup efs (hope this <- works...)
yah, thank you again...
have a nice day..
Hi Everyone
I've bricked my S4 stupidly by trying to install CF Auto Root without having USB Debugging enabled.
No my phone starts up telling me there was an incomplete upgrade and to continue it but kies can't seem to find anything.
I've tried reflashing the stock firmware but I keep receiving a error saying it can't find the PIT file for mapping.
Does anyone have one for the S4 I9505 INTL (UK) Variant.
Thanks
sandeepsb said:
Hi Everyone
I've bricked my S4 stupidly by trying to install CF Auto Root without having USB Debugging enabled.
No my phone starts up telling me there was an incomplete upgrade and to continue it but kies can't seem to find anything.
I've tried reflashing the stock firmware but I keep receiving a error saying it can't find the PIT file for mapping.
Does anyone have one for the S4 I9505 INTL (UK) Variant.
Thanks
Click to expand...
Click to collapse
usb debugging
see my signature for flashing with pit :good:
samersh72 said:
usb debugging
see my signature for flashing with pit :good:
Click to expand...
Click to collapse
I've just downloaded your pit file. The problem here is I can't get back into my phone and I can only go into download mode. Initially I set USB Debugging as off and tried flashing. So now I'm stuck with a bricked phone.
sandeepsb said:
I've just downloaded your pit file. The problem here is I can't get back into my phone and I can only go into download mode. Initially I set USB Debugging as off and tried flashing. So now I'm stuck with a bricked phone.
Click to expand...
Click to collapse
NO need to enable usb debugging to flash with odin, just put pit file and the firmware in odin and flash
sandeepsb said:
I've just downloaded your pit file. The problem here is I can't get back into my phone and I can only go into download mode. Initially I set USB Debugging as off and tried flashing. So now I'm stuck with a bricked phone.
Click to expand...
Click to collapse
Do not start panicking so soon all this happens while we tinker with device follow what samersh72 saying u ll have ur device working
Its not bricked at all
Sent from my GT-I9500 using xda premium
samersh72 said:
usb debugging
see my signature for flashing with pit :good:
Click to expand...
Click to collapse
samersh72 said:
NO need to enable usb debugging to flash with odin, just put pit file and the firmware in odin and flash
Click to expand...
Click to collapse
I've tried it and I'm getting a Failed message:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
I've attached a screenshot.
sandeepsb said:
I've tried it and I'm getting a Failed message:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
I've attached a screenshot.
Click to expand...
Click to collapse
Just tried again and I'm receiving this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
sandeepsb said:
Just tried again and I'm receiving this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try using ODIN 3.07 version
also make sure u have no kies programme running , try using diff usb port
it should work
sandeepsb said:
I've tried it and I'm getting a Failed message:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
I've attached a screenshot.
Click to expand...
Click to collapse
remove pit file from folder and put it on desktop and the firmware and odin
use odin 3.07 or 1.85
change usb port and use original cable
if you can go in recovery (i doubt)make a wipe)
retry
samersh72 said:
remove pit file from folder and put it on desktop and the firmware and odin
use odin 3.07 or 1.85
change usb port and use original cable
if you can go in recovery (i doubt)make a wipe)
retry
Click to expand...
Click to collapse
Crisis averted just flashed the PIT without anything in the PDA section and I've managed to boot back into my phone.
Thanks for the help and the PIT file.
sandeepsb said:
Crisis averted just flashed the PIT without anything in the PDA section and I've managed to boot back into my phone.
Thanks for the help and the PIT file.
Click to expand...
Click to collapse
glad to hear that, but usually it is flashed with the firmware if you would try again you will succeed......any way you make it :good:
Same happened with me, no matter how many times I tried flashing the PIT with the firmware, it just wouldn't have it at all.
When I flashed the PIT on it's own, it flashed fine, said reset, then booted back into android.
Glad you got it sorted though! It's scary when you see FAIL in big letters when flashing stuff! haha.
Read more, Learn more.....
---------- Post added at 07:45 PM ---------- Previous post was at 07:35 PM ----------
but in some cases where there is a serious firmware issue, pit file will work only with flashing firmware
Please help, I need the PIT file for M919 (T-mobile), anyone have it? Pleaseeeeee.
T-Mo GS4 Pit File
xs2k said:
Please help, I need the PIT file for M919 (T-mobile), anyone have it? Pleaseeeeee.
Click to expand...
Click to collapse
I too Also need this file as well, I can only seem to find the international GS4 pit files.
samersh72 said:
NO need to enable usb debugging to flash with odin, just put pit file and the firmware in odin and flash
Click to expand...
Click to collapse
samersh72 said:
remove pit file from folder and put it on desktop and the firmware and odin
use odin 3.07 or 1.85
change usb port and use original cable
if you can go in recovery (i doubt)make a wipe)
retry
Click to expand...
Click to collapse
I cant find the PIT partition file anywhere on your sig
I dunno if im looking in the wrong place. Can you give me a hint on where it is?
Im having problems with my phone and it wont load past the boot animation.
Chris
scientificharmony said:
I cant find the PIT partition file anywhere on your sig
I dunno if im looking in the wrong place. Can you give me a hint on where it is?
Im having problems with my phone and it wont load past the boot animation.
Chris
Click to expand...
Click to collapse
Attached here in first post http://forum.xda-developers.com/showthread.php?t=2265477
Sent from my Galaxy
samersh72 said:
Attached here in first post http://forum.xda-developers.com/showthread.php?t=2265477
Sent from my Galaxy
Click to expand...
Click to collapse
Hi, Thanks for that info. The device has now boot, but i seem to have error messages in recovery cannot mount E:\ etc etc
how the hell do i fix that lol
scientificharmony said:
Hi, Thanks for that info. The device has now boot, but i seem to have error messages in recovery cannot mount E:\ etc etc
how the hell do i fix that lol
Click to expand...
Click to collapse
reflash with i9505-cwm-recovery-6.0.3.2-4
wipe all
reflash with pit CSB_signed_Fusion3_EUR_0325_V2 and pda I9505XXUAME2_I9505OLBAMDM_I9505DXUAME2_HOME.tar
Just a word from me guys.
Please don't underestimate power of changing USB port and/or USB cable. I've just been sitting on soft-bricked s4, nothing seemed to work, ODIN 3.x or 1.8, original firmware or third party ROM/recovery etc, PIT file, nothing could be overwritten. I restarted PC and instal/reinstall drivers.. nothing.
I've changed the cable and USB port to the rear one et voila, all worked as a charm.
good luck.
OK so this is what i did. so i tried to root my s4, and in odin it said fail. so i took out the battery. and try to turn it on now it has the phone YELLOW triangle and a monitor. it says "firumware upgrade encountered an issue. Please select recovery mod in kies & try again.
what i have tried so far was download the sprint stock and odin it back. i used qbking77 . com the stock i used is linked on that website. which then links me to stockroms.net. so during the process of doing going back to stock it said fail. i read some where that in the id:com on odin, it should say 0:[COM6] and i read some where else that it does have to say com6 it could say com3. i dont know if that matters. and i also read on the forum they say to use another stock rom? is that also if so where can i get one besides from stockroms.net please someone help me..
this is what it says when i try to odin to stock:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Sounds like a bad rom download. Download the rim again or get it from a sticky on xda.
Also it doesn't matter what com port Odin puts the phone on as long as it sees it.
Sent from my SPH-L720 using xda app-developers app
tordsrv 1892
im still fairly new at the whole rooting scene. could you possible link me to the stock rom? oh btw idk if this would matter but i think i had the MF9..
i just want to go back stock for now and get this phone to work.. than i will try again.. thank you in advance!
my uncle also said there is a odin file not the program. but an odin file that you use with odin program. is this true for the s4? if so could you link me to it also!
i just tried it again. and im getting this error now..
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I have read that that download fron QBKing is bad. As a poster above me said, download the rom from XDA instead and redo the process. Also, be sure to use the usb cable that came with your phone as others can cause the same issue. Also....if it fails again, try a different usb port. Good luck
Sent from my SPH-L720 using Tapatalk 4 Beta
could someone link me to the right post that has the sprint stock rom? thank you
texassoljaz said:
could someone link me to the right post that has the sprint stock rom? thank you
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2382188
Last post
Sent from my SPH-L720 using xda premium
and ubuings
ok so.. i downloaded this stock firmware
http://forum.xda-developers.com/showthread.php?t=2258107
and it actually goes futher but than it said i dont have a pit file.. im sorry this is my first time and it is so hard to understand everything.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF9FirmwareAIO.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
could someone tell me wht it says no PIT partition? i have tried so many different stocks for the sprint phone.
im sure mines was the MF9. but i also tried the MDL and MDC.
texassoljaz said:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF9FirmwareAIO.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
could someone tell me wht it says no PIT partition? i have tried so many different stocks for the sprint phone.
im sure mines was the MF9. but i also tried the MDL and MDC.
Click to expand...
Click to collapse
Bot trying to scare you here but if you google the pit error people are being told its a faulty motherboard
Sent from my SPH-L720 using xda premium
same thing happen to my boys gs2 when i was flashing a recovery for him... same ishh.. all i had to do is use odin to unroot and flash a stock rom via odin.. its worked for me.. all the phone would do is go into download mode.. thats it.. no recovery and it wouldnt boot.. stuck in download mode.. i plugged it in to my pc.. odin noticed the phone i flashed stock unrooted rom.. phone rebooted at the end and everything was fine..one crazy thing was after that happen i tried to root again and flash a custom recovery and it happen again.. so i had to fix it again.. i just could not root that phone after that.. had to keep it stock.. my buddy was just happy to have his phone he didnt care about root after that!!
texassoljaz said:
OK so this is what i did. so i tried to root my s4, and in odin it said fail. so i took out the battery. and try to turn it on now it has the phone YELLOW triangle and a monitor. it says "firumware upgrade encountered an issue. Please select recovery mod in kies & try again.
what i have tried so far was download the sprint stock and odin it back. i used qbking77 . com the stock i used is linked on that website. which then links me to stockroms.net. so during the process of doing going back to stock it said fail. i read some where that in the id:com on odin, it should say 0:[COM6] and i read some where else that it does have to say com6 it could say com3. i dont know if that matters. and i also read on the forum they say to use another stock rom? is that also if so where can i get one besides from stockroms.net please someone help me..
this is what it says when i try to odin to stock:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Click to expand...
Click to collapse
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
ROMANTiC KiD said:
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
I tried what you said than it went to this
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
but now i have a loading bar on my phone. so i dont know whats going to happen i will leave it for a while to see what happens.
texassoljaz said:
I tried what you said than it went to this
Added!!
Odin v.3 engine (ID:7)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Complete(Write) operation failed.
Added!!
All threads completed. (succeed 0 / failed 1)
but now i have a loading bar on my phone. so i dont know whats going to happen i will leave it for a while to see what happens.
Click to expand...
Click to collapse
Hmm weird. Redownload the file from qbking77 and delete the extension again. Also try it with a different version of odin for example the one that qbking uses v1.85 (which is also the one I use) and pull out battery and put the battery in and manually set it to download mode and try it one more time. Btw any chance did you get a pop up in your screen saying something about an error of some kind saying about a parameter before?
Edit: Also probably restart computer just in case also.
Sent from my SPH-L720 using xda app-developers app
ROMANTiC KiD said:
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
ROMANTiC KiD said:
Hmm weird. Redownload the file from qbking77 and delete the extension again. Also try it with a different version of odin for example the one that qbking uses v1.85 (which is also the one I use) and pull out battery and put the battery in and manually set it to download mode and try it one more time. Btw any chance did you get a pop up in your screen saying something about an error of some kind saying about a parameter before?
Edit: Also probably restart computer just in case also.
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
no i never never got a parameter error.. i also have window 8 do you think that will affect anything? i will try qbking than update you.. thanks for helping. greatly appreciated!
texassoljaz said:
no i never never got a parameter error.. i also have window 8 do you think that will affect anything? i will try qbking than update you.. thanks for helping. greatly appreciated!
Click to expand...
Click to collapse
Hmm... alrighty. Nah it shouldnt affect anything but you can also try with other computer as well or different version of windows. No problem hope you get it solved soon!
Sent from my SPH-L720 using xda app-developers app
so after trying it. i got a parameter error. what does this mean?
so i end up getting this far.. do you know how to fix this?
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> aboot.mbn
<ID:0/010> NAND Write Start!!
<ID:0/010> tz.mbn
<ID:0/010> boot.img
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> aboot.mbn
<ID:0/010> NAND Write Start!!
<ID:0/010> tz.mbn
<ID:0/010> boot.img
<ID:0/010> recovery.img
<ID:0/010> system.img.ext4
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
i dont get it. so i got it to start the green bar in on odin.. than all of a sudden it say fails. and one my phone the blue bar went half way
yessss!!!!! i got
can someone please help me , i tryed to put a new rom on my phone and ended up with it giving me and error saying firmware upgrade encountered an issue please select recovery mode in kies, ive tryed to restore in kies but when i do it ends up saying device not found and failing, i can still get onto download mode
ive tryed diffrent odins and same error all the time the last thing i tryed was full wipe and rebuild still no joy
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> PDA_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> MODEM_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> CSC_FULL_WIPE_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Help is simple you are in the wrong forum this is I9300 .
Use the report button for moving the post .
Based on your previous posts you are either not following the instructions or need a service centre repair .
jje
SAMGS4 said:
<OSM> BOOTLOADER_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> PDA_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> MODEM_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> CSC_FULL_WIPE_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
Click to expand...
Click to collapse
Mh, is this normal for ODIN, having a single PDA file given?
@ SAMGS4: What exactly did you do? For me it looks like you put the same file in all file selection lines.
Do you still have access to phone's UI and can check the complete device properties?
I know this is the wrong device forum but if a mod moves this topic to the proper location, the replies got moved also.
someone please help
HSishi said:
Mh, is this normal for ODIN, having a single PDA file given?
@ SAMGS4: What exactly did you do? For me it looks like you put the same file in all file selection lines.
Do you still have access to phone's UI and can check the complete device properties?
I know this is the wrong device forum but if a mod moves this topic to the proper location, the replies got moved also.
Click to expand...
Click to collapse
thanks and ive just reported the post to be moved, and also i have no access to the phone, i can get it on the download mode and when it says about firmware upgrade kies update etc
Well ... there might be another reason why you can't flash the wanted file - the DL is corrupt. But ODIN checked the md5 hash and the file passed the test.
Did you try to flash another, earlier leaked, ROM for your phone?
Does the ROM match to your country / provider code? Maybe the ROM you try to flash doesn't match exactly to the phone you have; there are various SGS4 models.
someone please help
HSishi said:
Well ... there might be another reason why you can't flash the wanted file - the DL is corrupt. But ODIN checked the md5 hash and the file passed the test.
Did you try to flash another, earlier leaked, ROM for your phone?
Does the ROM match to your country / provider code? Maybe the ROM you try to flash doesn't match exactly to the phone you have; there are various SGS4 models.
Click to expand...
Click to collapse
just tryed a new rom and pit file and heres the results
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
my phone was on the (3g) three network uk its a gt-i9505 if someone could direct me to a rom and pit file for my phone i could try would be very much appreciated
heres my LAST ODIN FLASH TRY seems to for got bit further then last time and on my phone i got a little bit of a blue loading bar then it failed
SAMGS4 said:
my phone was on the (3g) three network uk its a gt-i9505 if someone could direct me to a rom and pit file for my phone i could try would be very much appreciated
heres my LAST ODIN FLASH TRY seems to for got bit further then last time and on my phone i got a little bit of a blue loading bar then it failed
Click to expand...
Click to collapse
While flashing using odin make sure no kies programme are running in the background
U can try different cable / usb ports etc will work and try using without pit,
U should use pit file as a last option for now u try without that and do as above will work
.
I Just tried a diffrent usb port and didnt use the pit file and it got a bit futher then first time but failed again here is the results <ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
someone please help
i just tried diffrent usb post and made sure kies or no firewall was on , didnt use the pit file like you said and phone got bit futher then first time but still failed here the results
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
U
SAMGS4 said:
i just tried diffrent usb post and made sure kies or no firewall was on , didnt use the pit file like you said and phone got bit futher then first time but still failed here the results
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:6)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
boot.img
NAND Write Start!!
recovery.img
system.img.ext4
Complete(Write) operation failed.
Added!!
All threads completed. (succeed 0 / failed 1)
Removed!!
Added!!
Click to expand...
Click to collapse
Did u close all the kies programme from the background that must be the issue
Or uninstall kies and try
There should be 3 four kies file running in the background close all from task manager try restarting pc and try
someone please help
just uninstalled kies and tryed same as before
someone please help
i have a laptop with windows xp on it should i try on this??
OTE=SAMGS4;44354942]i have a laptop with windows xp on it should i try on this??[/QUOTE]
I'd give it a try. Update the drivers before you attempt it. I'm on three as well and have flashed the same firmware without problems. Have you tried flashing a recovery and wiping the phone. Internal SD etc? Wouldn't do it any harm
someone please help
symondo12 said:
OTE=SAMGS4;44354942]i have a laptop with windows xp on it should i try on this??
Click to expand...
Click to collapse
I'd give it a try. Update the drivers before you attempt it. I'm on three as well and have flashed the same firmware without problems. Have you tried flashing a recovery and wiping the phone. Internal SD etc? Wouldn't do it any harm[/QUOTE]
hi could you please give me a link to stock rom for three please as cant find one and what recovery would i flash?? thanks?
Mh, can you get into Recovery mode? If not, flash an alternate Recovery mod first. Try PhilZ Touch Recovery. It's being flashed within DL mode, fill only PDA field.
Ah, I didn't notice yet ... you use ODIN 3.04. That's an outdated version; maybe 3.04 can't handle an I9505.
Most current version is 3.07, get it here. In this post it's said ODIN 1.85 can already deal with an I9595; try this too.
Does ODIN run with Admin rights? Maybe there's a problem with your Windows UAC.
//HSishi
http://forum.xda-developers.com/showthread.php?t=2281367
That's the link for philz recovery. Download the latest .tar and flash in O.
Boot into recovery and wipe everything including the internal SD. Make sure you back up.
By the looks of it you are flashing the latest three firmware. MEA H3G.
I'd download the firmware again. You can get it from Sammobile.com. you'll need to register an account. Think its labelled as Hutchisons 3G
someone please help
i just tryed to flash PhilZ Touch Recovery and it failed, also ive tried all the odins and the one that seems to get me the furthest is the 3.04
someone please help
anymore ideas?? pls:crying:
Have you tried another PC, one with Win 7 or 8 on it?It doesn't look like a partition problem, it seems to get further through each time but keeps failing. Might be a problem with your PC...
Oh, and I use ODIN 3.04 to flash too...
I've got a sprint galaxy s4, was running 4.2.2 and I had added the hotspot mod by overwriting some files to make that happen. I was attempting to go back to stock in order to update to 4.3 via an Odin3 flash and something happened. I can only boot into the download mode, I can't get into recovery mode at all. If I try to get into recovery, I get the message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
Kies will not recognize my phone. When I plug it into my computer via usb, I hear a notification. Kies attempts to connect, but never does successfully. I have no way of getting my serial number as I can't boot it and it's not listed under the battery cover. I have tried uninstalling/reinstalling drivers with no success. I have tried to uninstall Kies completely and flash via Odin3 but get a failure below
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMF9_L720SPTAMF9_L720VPUAMF9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
Also tried again and got these messages
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMF9_L720SPTAMF9_L720VPUAMF9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Removed!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I hope I've provided info on what I have tried. I am not an expert by any means, but would really appreciate any help. At this point I'm looking to just get back to stock and have a usable phone. I don't care about losing any info and am willing to wipe/flash whatever I can. Thank you for any input! I'm hoping to not have to take this to the sprint store
You just have to odin the stock mf9 tar again. I would try a different version of odin, a different usb port, or a different usb cable. Odin will fix your problem, don't use kies. I used odin 3 version 3.07 but I've also had a lot of success with odin 3 ver 1.85 that is included when you download cf autoroot. Also, make sure you are running odin as administrator.
cruise350 said:
You just have to odin the stock mf9 tar again. I would try a different version of odin, a different usb port, or a different usb cable. Odin will fix your problem, don't use kies. I used odin 3 version 3.07 but I've also had a lot of success with odin 3 ver 1.85 that is included when you download cf autoroot. Also, make sure you are running odin as administrator.
Click to expand...
Click to collapse
Thanks for your reply. I am trying to flash the stock .tar but I'm not having any success. I get the error messages I listed above. Any clue what those mean or what I could be doing wrong? That looks like greek to me. I really don't know what any of it means.
i would just use the CF-autoroot odin......this has saved my ass twice !!! seems to be the " mirical odin " program
chris-allen said:
i would just use the CF-autoroot odin......this has saved my ass twice !!! seems to be the " mirical odin " program
Click to expand...
Click to collapse
wow. Finally figured it out. I tried 3 different USB ports, none of those worked. Tried a 4th on the back of my PC and viola, finally got Odin to work. THanks for your help!