OK so this is what i did. so i tried to root my s4, and in odin it said fail. so i took out the battery. and try to turn it on now it has the phone YELLOW triangle and a monitor. it says "firumware upgrade encountered an issue. Please select recovery mod in kies & try again.
what i have tried so far was download the sprint stock and odin it back. i used qbking77 . com the stock i used is linked on that website. which then links me to stockroms.net. so during the process of doing going back to stock it said fail. i read some where that in the id:com on odin, it should say 0:[COM6] and i read some where else that it does have to say com6 it could say com3. i dont know if that matters. and i also read on the forum they say to use another stock rom? is that also if so where can i get one besides from stockroms.net please someone help me..
this is what it says when i try to odin to stock:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Sounds like a bad rom download. Download the rim again or get it from a sticky on xda.
Also it doesn't matter what com port Odin puts the phone on as long as it sees it.
Sent from my SPH-L720 using xda app-developers app
tordsrv 1892
im still fairly new at the whole rooting scene. could you possible link me to the stock rom? oh btw idk if this would matter but i think i had the MF9..
i just want to go back stock for now and get this phone to work.. than i will try again.. thank you in advance!
my uncle also said there is a odin file not the program. but an odin file that you use with odin program. is this true for the s4? if so could you link me to it also!
i just tried it again. and im getting this error now..
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I have read that that download fron QBKing is bad. As a poster above me said, download the rom from XDA instead and redo the process. Also, be sure to use the usb cable that came with your phone as others can cause the same issue. Also....if it fails again, try a different usb port. Good luck
Sent from my SPH-L720 using Tapatalk 4 Beta
could someone link me to the right post that has the sprint stock rom? thank you
texassoljaz said:
could someone link me to the right post that has the sprint stock rom? thank you
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2382188
Last post
Sent from my SPH-L720 using xda premium
and ubuings
ok so.. i downloaded this stock firmware
http://forum.xda-developers.com/showthread.php?t=2258107
and it actually goes futher but than it said i dont have a pit file.. im sorry this is my first time and it is so hard to understand everything.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF9FirmwareAIO.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
could someone tell me wht it says no PIT partition? i have tried so many different stocks for the sprint phone.
im sure mines was the MF9. but i also tried the MDL and MDC.
texassoljaz said:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF9FirmwareAIO.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
could someone tell me wht it says no PIT partition? i have tried so many different stocks for the sprint phone.
im sure mines was the MF9. but i also tried the MDL and MDC.
Click to expand...
Click to collapse
Bot trying to scare you here but if you google the pit error people are being told its a faulty motherboard
Sent from my SPH-L720 using xda premium
same thing happen to my boys gs2 when i was flashing a recovery for him... same ishh.. all i had to do is use odin to unroot and flash a stock rom via odin.. its worked for me.. all the phone would do is go into download mode.. thats it.. no recovery and it wouldnt boot.. stuck in download mode.. i plugged it in to my pc.. odin noticed the phone i flashed stock unrooted rom.. phone rebooted at the end and everything was fine..one crazy thing was after that happen i tried to root again and flash a custom recovery and it happen again.. so i had to fix it again.. i just could not root that phone after that.. had to keep it stock.. my buddy was just happy to have his phone he didnt care about root after that!!
texassoljaz said:
OK so this is what i did. so i tried to root my s4, and in odin it said fail. so i took out the battery. and try to turn it on now it has the phone YELLOW triangle and a monitor. it says "firumware upgrade encountered an issue. Please select recovery mod in kies & try again.
what i have tried so far was download the sprint stock and odin it back. i used qbking77 . com the stock i used is linked on that website. which then links me to stockroms.net. so during the process of doing going back to stock it said fail. i read some where that in the id:com on odin, it should say 0:[COM6] and i read some where else that it does have to say com6 it could say com3. i dont know if that matters. and i also read on the forum they say to use another stock rom? is that also if so where can i get one besides from stockroms.net please someone help me..
this is what it says when i try to odin to stock:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Click to expand...
Click to collapse
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
ROMANTiC KiD said:
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
I tried what you said than it went to this
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
but now i have a loading bar on my phone. so i dont know whats going to happen i will leave it for a while to see what happens.
texassoljaz said:
I tried what you said than it went to this
Added!!
Odin v.3 engine (ID:7)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Complete(Write) operation failed.
Added!!
All threads completed. (succeed 0 / failed 1)
but now i have a loading bar on my phone. so i dont know whats going to happen i will leave it for a while to see what happens.
Click to expand...
Click to collapse
Hmm weird. Redownload the file from qbking77 and delete the extension again. Also try it with a different version of odin for example the one that qbking uses v1.85 (which is also the one I use) and pull out battery and put the battery in and manually set it to download mode and try it one more time. Btw any chance did you get a pop up in your screen saying something about an error of some kind saying about a parameter before?
Edit: Also probably restart computer just in case also.
Sent from my SPH-L720 using xda app-developers app
ROMANTiC KiD said:
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
ROMANTiC KiD said:
Hmm weird. Redownload the file from qbking77 and delete the extension again. Also try it with a different version of odin for example the one that qbking uses v1.85 (which is also the one I use) and pull out battery and put the battery in and manually set it to download mode and try it one more time. Btw any chance did you get a pop up in your screen saying something about an error of some kind saying about a parameter before?
Edit: Also probably restart computer just in case also.
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
no i never never got a parameter error.. i also have window 8 do you think that will affect anything? i will try qbking than update you.. thanks for helping. greatly appreciated!
texassoljaz said:
no i never never got a parameter error.. i also have window 8 do you think that will affect anything? i will try qbking than update you.. thanks for helping. greatly appreciated!
Click to expand...
Click to collapse
Hmm... alrighty. Nah it shouldnt affect anything but you can also try with other computer as well or different version of windows. No problem hope you get it solved soon!
Sent from my SPH-L720 using xda app-developers app
so after trying it. i got a parameter error. what does this mean?
so i end up getting this far.. do you know how to fix this?
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> aboot.mbn
<ID:0/010> NAND Write Start!!
<ID:0/010> tz.mbn
<ID:0/010> boot.img
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> aboot.mbn
<ID:0/010> NAND Write Start!!
<ID:0/010> tz.mbn
<ID:0/010> boot.img
<ID:0/010> recovery.img
<ID:0/010> system.img.ext4
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
i dont get it. so i got it to start the green bar in on odin.. than all of a sudden it say fails. and one my phone the blue bar went half way
yessss!!!!! i got
Related
Hi all,
i tried to flash cyanogenmod unofficial, on the flash an error was comming, now the device dosent start...
when i boot the phone normaly, is comming: firmware upgrade encountered an issue. please select recovery mode in kies & try again.
i tryed to flash the original firmware:
(I9505XXUAMDF_I9505AUTAMD8_AUT)
I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar
but an error in odin is comming:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Removed!!
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
please can you help me?
cutalaxy said:
Hi all,
i tried to flash cyanogenmod unofficial, on the flash an error was comming, now the device dosent start...
when i boot the phone normaly, is comming: firmware upgrade encountered an issue. please select recovery mode in kies & try again.
i tryed to flash the original firmware:
(I9505XXUAMDF_I9505AUTAMD8_AUT)
I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar
but an error in odin is comming:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Removed!!
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
please can you help me?
Click to expand...
Click to collapse
Try flashing along with pit file
MKe sure u have the proper file for the same
Sent from my GT-I9500 using xda premium
123hiten said:
Try flashing along with pit file
MKe sure u have the proper file for the same
Sent from my GT-I9500 using xda premium
Click to expand...
Click to collapse
where can i find the pit file?
cutalaxy said:
where can i find the pit file?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2265477&highlight=stock+firmware
this link has it attached take the correct one u would know better
dont worry i had the same issue on my note 2 a month ago and was wrkng fine after flashing rescue firmware urs wil work too
damn, it doeset work for me
is it hard brick?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
cutalaxy said:
damn, it doeset work for me
is it hard brick?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Click to expand...
Click to collapse
No its not at a hard brick dont worry dont panic thats the best wat to work around
I would say dont use pit file unless its last option and try without that only may be in other pc using other cable some below steps myte also help u
2) Install later Kies.
3) Kill al kies applications (all 4 of them).
disable antivirus or whatever you got there.) Get to Download Mode and push Vol Up.
7) Open Odin.
8) Plug the device to your laptop.
Does it see the device?
If NO:
A) Get another usb cable, are you using ?
B) Try different Odin Versions (download 3 or 4).
C) Try another USB port.
D) Still no luck? reboot the pc and start from step 3.
---------- Post added at 08:30 PM ---------- Previous post was at 08:23 PM ----------
Download 2/3 stock firmware and try installing thru ODIN it should work
Make sure u have all the drivers installed
MAke sure kies is not open or make sure its closed even in background process
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
cutalaxy said:
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
Click to expand...
Click to collapse
Official firmware is not a wiping one. It doesnt flash userdata, it replace system, recovery, and some other partitions.
sent from my Galaxy
cutalaxy said:
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
Click to expand...
Click to collapse
Great to hear that man
If u flash stock firmware all will remain as its in ODIN but its good if u reset the device after or b4 root
Also take a EFS backup of ur device and be safe
i had root before the device bricks... so i rootet it now again, and works good...
yeah, i will backup efs (hope this <- works...)
yah, thank you again...
have a nice day..
can someone please help me , i tryed to put a new rom on my phone and ended up with it giving me and error saying firmware upgrade encountered an issue please select recovery mode in kies, ive tryed to restore in kies but when i do it ends up saying device not found and failing, i can still get onto download mode
ive tryed diffrent odins and same error all the time the last thing i tryed was full wipe and rebuild still no joy
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> PDA_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> MODEM_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> CSC_FULL_WIPE_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Help is simple you are in the wrong forum this is I9300 .
Use the report button for moving the post .
Based on your previous posts you are either not following the instructions or need a service centre repair .
jje
SAMGS4 said:
<OSM> BOOTLOADER_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> PDA_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> MODEM_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> CSC_FULL_WIPE_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
Click to expand...
Click to collapse
Mh, is this normal for ODIN, having a single PDA file given?
@ SAMGS4: What exactly did you do? For me it looks like you put the same file in all file selection lines.
Do you still have access to phone's UI and can check the complete device properties?
I know this is the wrong device forum but if a mod moves this topic to the proper location, the replies got moved also.
someone please help
HSishi said:
Mh, is this normal for ODIN, having a single PDA file given?
@ SAMGS4: What exactly did you do? For me it looks like you put the same file in all file selection lines.
Do you still have access to phone's UI and can check the complete device properties?
I know this is the wrong device forum but if a mod moves this topic to the proper location, the replies got moved also.
Click to expand...
Click to collapse
thanks and ive just reported the post to be moved, and also i have no access to the phone, i can get it on the download mode and when it says about firmware upgrade kies update etc
Well ... there might be another reason why you can't flash the wanted file - the DL is corrupt. But ODIN checked the md5 hash and the file passed the test.
Did you try to flash another, earlier leaked, ROM for your phone?
Does the ROM match to your country / provider code? Maybe the ROM you try to flash doesn't match exactly to the phone you have; there are various SGS4 models.
someone please help
HSishi said:
Well ... there might be another reason why you can't flash the wanted file - the DL is corrupt. But ODIN checked the md5 hash and the file passed the test.
Did you try to flash another, earlier leaked, ROM for your phone?
Does the ROM match to your country / provider code? Maybe the ROM you try to flash doesn't match exactly to the phone you have; there are various SGS4 models.
Click to expand...
Click to collapse
just tryed a new rom and pit file and heres the results
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
my phone was on the (3g) three network uk its a gt-i9505 if someone could direct me to a rom and pit file for my phone i could try would be very much appreciated
heres my LAST ODIN FLASH TRY seems to for got bit further then last time and on my phone i got a little bit of a blue loading bar then it failed
SAMGS4 said:
my phone was on the (3g) three network uk its a gt-i9505 if someone could direct me to a rom and pit file for my phone i could try would be very much appreciated
heres my LAST ODIN FLASH TRY seems to for got bit further then last time and on my phone i got a little bit of a blue loading bar then it failed
Click to expand...
Click to collapse
While flashing using odin make sure no kies programme are running in the background
U can try different cable / usb ports etc will work and try using without pit,
U should use pit file as a last option for now u try without that and do as above will work
.
I Just tried a diffrent usb port and didnt use the pit file and it got a bit futher then first time but failed again here is the results <ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
someone please help
i just tried diffrent usb post and made sure kies or no firewall was on , didnt use the pit file like you said and phone got bit futher then first time but still failed here the results
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
U
SAMGS4 said:
i just tried diffrent usb post and made sure kies or no firewall was on , didnt use the pit file like you said and phone got bit futher then first time but still failed here the results
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:6)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
boot.img
NAND Write Start!!
recovery.img
system.img.ext4
Complete(Write) operation failed.
Added!!
All threads completed. (succeed 0 / failed 1)
Removed!!
Added!!
Click to expand...
Click to collapse
Did u close all the kies programme from the background that must be the issue
Or uninstall kies and try
There should be 3 four kies file running in the background close all from task manager try restarting pc and try
someone please help
just uninstalled kies and tryed same as before
someone please help
i have a laptop with windows xp on it should i try on this??
OTE=SAMGS4;44354942]i have a laptop with windows xp on it should i try on this??[/QUOTE]
I'd give it a try. Update the drivers before you attempt it. I'm on three as well and have flashed the same firmware without problems. Have you tried flashing a recovery and wiping the phone. Internal SD etc? Wouldn't do it any harm
someone please help
symondo12 said:
OTE=SAMGS4;44354942]i have a laptop with windows xp on it should i try on this??
Click to expand...
Click to collapse
I'd give it a try. Update the drivers before you attempt it. I'm on three as well and have flashed the same firmware without problems. Have you tried flashing a recovery and wiping the phone. Internal SD etc? Wouldn't do it any harm[/QUOTE]
hi could you please give me a link to stock rom for three please as cant find one and what recovery would i flash?? thanks?
Mh, can you get into Recovery mode? If not, flash an alternate Recovery mod first. Try PhilZ Touch Recovery. It's being flashed within DL mode, fill only PDA field.
Ah, I didn't notice yet ... you use ODIN 3.04. That's an outdated version; maybe 3.04 can't handle an I9505.
Most current version is 3.07, get it here. In this post it's said ODIN 1.85 can already deal with an I9595; try this too.
Does ODIN run with Admin rights? Maybe there's a problem with your Windows UAC.
//HSishi
http://forum.xda-developers.com/showthread.php?t=2281367
That's the link for philz recovery. Download the latest .tar and flash in O.
Boot into recovery and wipe everything including the internal SD. Make sure you back up.
By the looks of it you are flashing the latest three firmware. MEA H3G.
I'd download the firmware again. You can get it from Sammobile.com. you'll need to register an account. Think its labelled as Hutchisons 3G
someone please help
i just tryed to flash PhilZ Touch Recovery and it failed, also ive tried all the odins and the one that seems to get me the furthest is the 3.04
someone please help
anymore ideas?? pls:crying:
Have you tried another PC, one with Win 7 or 8 on it?It doesn't look like a partition problem, it seems to get further through each time but keeps failing. Might be a problem with your PC...
Oh, and I use ODIN 3.04 to flash too...
Yesterday I had just rooted my Sprint Galaxy S4 on 4.3 and tried flashing Sac's 4.3 Rom and it 1st left me at some shinig small android logo so i decided it would've been a better idea to restore back to stock ( with the back up i made in TWRP ) and after i restored the back up, the phone's screen was stuck on the yellow sprint boot screen. After that i've tried using Odin mutiple times as seen a solution in other posts to completely put the phone back to stock/unroot it and i get the following error from Odin: *Note I've tried using 2 different versions of odin and 2 different laptops.*
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Someone please help me out here
jaden7201 said:
Yesterday I had just rooted my Sprint Galaxy S4 on 4.3 and tried flashing Sac's 4.3 Rom and it 1st left me at some shinig small android logo so i decided it would've been a better idea to restore back to stock ( with the back up i made in TWRP ) and after i restored the back up, the phone's screen was stuck on the yellow sprint boot screen. After that i've tried using Odin mutiple times as seen a solution in other posts to completely put the phone back to stock/unroot it and i get the following error from Odin: *Note I've tried using 2 different versions of odin and 2 different laptops.*
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Someone please help me out here
Click to expand...
Click to collapse
Grab this tar (it's zipped, so unzip and use tar.md5..) and try it in Odin. It's the full MJA.
Also make sure to run Odin 'As administrator'
Thanks leadbuilder! I managed to reflash a stock 4.3 mja.tar from that exact link about an hour ago i right before i read your reply.
Thank you for repsponding though!
Thanks for the reply!
It's always good to know what happened. That way maybe others can benefit too.
If you hang around and read all the way through some of the posts you will quickly get a really good education on how this device works and have a blast with this phone. There are some really good devs and contributors here.
Good luck.
So I've been itching to get the new KitKat update that ATT released the other day for the GS4's but since I'm rooted, I of course cannot achieve that until I roll back to 4.2 with the Odin method. The only problem is..I cant seem to figure out why my phone won't accept the flash process.
This is the info from Odin..
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone also has some red text during the process (while its in Download mode) which says..
SW REV. CHECK FAIL : fused : 4 , Binary : 1
Not sure if that's important but the more information the better I suppose.
Anyway, if anyone has any leads or information that might be able to help me, please and thank you very much.
Cheers everyone!
-Fordo
Pretty sure you're on mk2 firmware and need these files http://forum.xda-developers.com/showthread.php?p=49687770
Thanks a bunch!
One more question, which file specifically should I be downloading from that thread?
Just making sure so I don't make any mistakes. Heh, cheers mate.
FordoGreenman said:
Thanks a bunch!
One more question, which file specifically should I be downloading from that thread?
Just making sure so I don't make any mistakes. Heh, cheers mate.
Click to expand...
Click to collapse
Just the all-in-one for simplicity. Instruction on how to use the file is in bottom of the post of that thread.
Im in a bit of a dilemma. I bought a new s5 with lollipop already installed on it and decided to root it. To root i needed to downgrade it. So using Odin, i attempted a downgrade only to come to a FAIL conclusion. I tried different .tar files that were kit kat, also found rooted lollipop firmware which always failed. I tried using a pit file which didnt seem to help. I cleared the cached and wiped the system memory multiple times. The only screen i am able to see is the Downloading screen and the reboot screen (volume up, home, and power)
I guess i soft bricked my phone... is there anyway to fix this problem?
Thanks a lot
AT&T - Bootloader is locked, don't think there is any way to downgrade from Lollipop
*Detection* said:
AT&T - Bootloader is locked, don't think there is any way to downgrade from Lollipop
Click to expand...
Click to collapse
yea that i realized, but is there anyway to get my phone back to its original state? Or because the bootloader is locked, this phone is forever soft bricked?
yakmicjan said:
yea that i realized, but is there anyway to get my phone back to its original state? Or because the bootloader is locked, this phone is forever soft bricked?
Click to expand...
Click to collapse
Boot in download mode then flash a LP firmware with odin
Sent from my SM-G900F using XDA Free mobile app
Soufiansky said:
Boot in download mode then flash a LP firmware with odin
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
I'm sorry what is LP firmware? If you mean stock, then I've already tried a lollipop firmware download with Odin which also always kept failing
yakmicjan said:
I'm sorry what is LP firmware? If you mean stock, then I've already tried a lollipop firmware download with Odin which also always kept failing
Click to expand...
Click to collapse
Yeah "LP" mean lollipop. Which fail message do you get ?
Sent from my SM-G900F using XDA Free mobile app
Soufiansky said:
Yeah "LP" mean lollipop. Which fail message do you get ?
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
First off, i used a few different update files. I'll just list the errors i get with each of them if that makes a difference:
*****
G900AUCU3BOC4_OneClick.exe (Can't add a pit file into this... it's a custom ODIN
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> One Click Downloader Mode
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005>
<ID:0/005>
<OSM> All threads completed. (succeed 0 / failed 1)
*****
Both of these files get the same error
AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5
AND
G900AUCU1ANCE_G900AATT1ANCE_G900AUCU1ANCE_HOME.tar.md5 (added a pit file : SM-G900A_pit.pit)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900AUCU1ANCE_G900AATT1ANCE_G900AUCU1ANCE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
In addition, i also tried to update the phone through an sd card using the file G900A-OF3toOI5-ota-2400258.cfg and renaming it to update.zip. Through the recovery menu, i wiped cache partition and did a factory reset. Then I applyed the update from external storage and get an Error Status 7.
This is everything i tried. Im running out of ideas and getting frustrated as this is a brand new phone
@yakmicjan But why are you using a modded version of odin ? Use a normal one , took the last version , then go to sammobile donwload the last firmware for your phone. Extract it and flash it with odin. It should work
Don't flash any pit file with it or anything , just the firmware.
Sent from my SM-G900F using XDA Free mobile app
I downloaded so many different types of odins and tried these files on all of them. The only modded version of odin is on the .exe file. I tried Odin3 v1.85, 3.10.6, 3.09. All of them gave me the same exact message.
Sadly, on sam mobile, the very last version they have for SM G900A is 4.4.2 which doesnt help since my phone already had lollipop installed on it. Does this mean i have to wait until they get a lollipop firmware for me to use my phone?
yakmicjan said:
I downloaded so many different types of odins and tried these files on all of them. The only modded version of odin is on the .exe file. I tried Odin3 v1.85, 3.10.6, 3.09. All of them gave me the same exact message.
Click to expand...
Click to collapse
Wait i just saw "Re-partion failed" , was it ticked before the flash ? Make sure only auto reboot and Reset time are ticked.
Sent from my SM-G900F using XDA Free mobile app
yakmicjan said:
This is everything i tried. Im running out of ideas and getting frustrated as this is a brand new phone
Click to expand...
Click to collapse
That's why you spend time reading and learning before just jumping in without knowing anything
Send it back, hope that they fix it under warranty
Soufiansky said:
Wait i just saw "Re-partion failed" , was it ticked before the flash ?
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
No it wasnt. I only have Auto Reboot and F.Reset Time ticked
Here is another error i'm getting. This time i added an AP, CP, and CSC file
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_G900AATT1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
yakmicjan said:
Here is another error i'm getting. This time i added an AP, CP, and CSC file
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_G900AATT1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Why do you add PIT FILE ? DO NOT DO IT. Flash only the firmware with Re-partition unchecked
Sent from my SM-G900F using XDA Free mobile app
Soufiansky said:
Why do you add PIT FILE ? DO NOT DO IT. Flash only the firmware with Re-partition unchecked
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
Im not adding the Pit File at all. I dont know why it shows up. I'll attach proof.
By the way, its the same exact error message as above.
Im so sorry about this annoying problem and for me being such a bother. Thank you so much for trying to help me
Why are you adding anything other than just the ROM in AP?
Remove everything from ODIN, and only add the ROM in AP
yakmicjan said:
Im not adding the Pit File at all. I dont know why it shows up. I'll attach proof.
By the way, its the same exact error message as above.
Click to expand...
Click to collapse
Look , choose ONLY the rom which is a very big .tar file and put it in AP , that's it. Do not add anything , anything. The firmware is about 2.4/2.5 go , you flash it and that's it
Sent from my SM-G900F using XDA Free mobile app
Soufiansky said:
Look , choose ONLY the rom which is a very big .tar file and put it in AP , that's it. Do not add anything , anything. The firmware is about 2.4/2.5 go , you flash it and that's it
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
What i am using now is the firmware i got from Sam's. I also tried checking and unchecking F. Reset Time. It gave me the same results
Same problem:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)