Related
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Congratulations!!
mrmomoman said:
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Click to expand...
Click to collapse
How did you attach the digitizer to the LCD? Aren't they glued together or something like that?
Because that's where my attempt went terribly wrong: Instead of getting the digitizer off my LCD, I broke my LCD... I bought a new complete screen unit because I didn't know how the LCD is attached to the digitizer!
The digitizer is semi-glued to the LCD panel which sits on the back along with the thin metal cover. The digitizer has a thin flat connector that connects to the back of the main board on the bottom. I slowly pryed off the LCD(grayish white in color) from the back of the Digitizer. It came off and I aligned it back up with the new digitizer and the glue residue left over from the LCD adhered to the rear of the new Digitizer. the tricky part is the thin connectors that attach to the mainboard. You have to get a pair of tweezers to pull it from the flat connector. When you get the digitizer you will see the new connector. Attaching that and the prying of the LCD was the hard part.
I read somewhere some guy said he broke the LCD but in truth it wasn't the LCD that he broke. He pryed apart the 3 layers of the Digitizer and thought he ruined the LCD. I thought the same thing orignally then I when the whole LCD/Digitizer was in my hand I was looking realized that the LCD was the grayish/white panel on the back. One can easily peel away the top 2 layers of the digitizer and would think that it could be the LCD they ruined.
I hope that makes sense. It was the first time I did this and I didn't see the video where someone removed the Screen. I only saw the Russian guy who didn't finish the job because he was stuck at the end. I just figured it out the hard way.
Also the T6 works but I think a t5 would be better. I only had a T6 and it did the job.
I am so glad I wore gloves or I would have had some major finger prints all over the unit
mrmomoman said:
The digitizer is semi-glued to the LCD panel which sits on the back along with the thin metal cover. The digitizer has a thin flat connector that connects to the back of the main board on the bottom. I slowly pryed off the LCD(grayish white in color) from the back of the Digitizer. It came off and I aligned it back up with the new digitizer and the glue residue left over from the LCD adhered to the rear of the new Digitizer. the tricky part is the thin connectors that attach to the mainboard. You have to get a pair of tweezers to pull it from the flat connector. When you get the digitizer you will see the new connector. Attaching that and the prying of the LCD was the hard part.
I read somewhere some guy said he broke the LCD but in truth it wasn't the LCD that he broke. He pryed apart the 3 layers of the Digitizer and thought he ruined the LCD. I thought the same thing orignally then I when the whole LCD/Digitizer was in my hand I was looking realized that the LCD was the grayish/white panel on the back. One can easily peel away the top 2 layers of the digitizer and would think that it could be the LCD they ruined.
I hope that makes sense. It was the first time I did this and I didn't see the video where someone removed the Screen. I only saw the Russian guy who didn't finish the job because he was stuck at the end. I just figured it out the hard way.
Also the T6 works but I think a t5 would be better. I only had a T6 and it did the job.
I am so glad I wore gloves or I would have had some major finger prints all over the unit
Click to expand...
Click to collapse
Thank you for your explanation! But I'm still not going to attempt this on my own any time soon... We'll see... Maybe I'll change my mind if my digitizer is broken or scratched...
Respect man! You mentioned that you bought digitizer for $17. Is it possible to buy mainboard for Touch HD from that place? Can you please advise where I can get it. And how much it will be?
Got to love a bit of micro-electronics DIY!
This just shows that HTC are taking people for a ride - there are a lot of people who would have just paid the price they stated. As you've only replaced the digitizer, shows they were taking the mick with the LCD and otherwise, what are these "internals" that HTC said it needed I wonder...??
Just replaced the digitizer on my HD and it took about 1.5hrs. As long as you're very careful, it's not that hard at all.
Make sure you have the Service Manual though as it was a great help.
Have you got the link for the service manual?
Ive just had to order a Digitizer as my phone has decided it doesnt want to work anymore (6 months to go on contract too ffs).
Managed to get one from a UK seller with tools for £17 so im happy.
KickAssMoves said:
Have you got the link for the service manual?
Click to expand...
Click to collapse
It's in the wiki.
WelshWarior said:
Just replaced the digitizer on my HD and it took about 1.5hrs. As long as you're very careful, it's not that hard at all.
Make sure you have the Service Manual though as it was a great help.
Click to expand...
Click to collapse
Hi:
How did you get the digitizer separated from the LCD?
I was thinking of putting two suction cups (1 on the back of the LCD, and the other on the front of the digitizer), heating everything up for a couple of minutes with a heat gun, and then pulling them apart holding the suction cups.
Does that make sense?
Thanks.
mrmomoman said:
To make a long story short:
I must have somehow put too much pressure on the digitizer to create a "newton ring" which in turn would not allow me to use the touch feature of the digitizer. I sent it to HTC USA to repair it. They noticed the "newton ring" as well as the modified ROM
They would not warranty the "newton ring" and said they would not repair the Digitizer due to the fact that it had been "hacked". They would replace the Digitizer, LCD and internals for $389.00. I told them they were smoking crack.
After paying HTC $25.00 for doing nothing they sent the phone back and I went online to order a Digitizer. I paid $17.00 which included shipping and I got it within 7 days.
The HTC service manual does not have a guide on how to replace the digitizer or the LCD. They really don't want you messing with it.
It was scary and I thought I had ruined the phone when I pryed the front of the unit open. At first the sticker to the digitizer came off(black framing) and then you have to pry the digitizer(its pretty stiff) from the frame. I destroyed the thin cable that led to the backside of the LCD but the new one has one already attached so I wasn't worried about that part. The LCD with a metal base plate is attached to the back of it. You have to slowly pry off the LCD from the backside of the digitizer.
Anyways I have assembled it back and everything is working perfectly. It was doing Micro-Surgery at times.
Just wanted to share my story.
Click to expand...
Click to collapse
i just had mines fixed called them told them wat i did that i found an outer sreen and tryed to replace it myself and completely destroyed the lil black screen inside of the 4screens put together and that my device software was moded now i had 469 out going and another 469 incoming calls they only charged me 113 but wen we first talked about it they did say about 350 until they see the device and then they will call you before the repair it but the did wipe out my device and reinstalled the oem rom they also gave me a full new body and zero'ed out the incoming and out going calls which never changest unless they put in a new mother board which makes my phone brand new
sorry if ive missed it, but how do you get the lcd and digi out from the black outer casing frame to start with ??, from what i can see it comes out by somehow pushing from the inside to make it pop out ?? could someone please explain a little bit more on how to do this, ill try and make a vid of me getting it out as i have yet to find one that shows this, also my screen has that wierd pearl essance look to it?? does this mean its the digitiser.
Cheers
Mike
pickie said:
sorry if ive missed it, but how do you get the lcd and digi out from the black outer casing frame to start with ??, from what i can see it comes out by somehow pushing from the inside to make it pop out ?? could someone please explain a little bit more on how to do this, ill try and make a vid of me getting it out as i have yet to find one that shows this, also my screen has that wierd pearl essance look to it?? does this mean its the digitiser.
Cheers
Mike
Click to expand...
Click to collapse
Mine had that pearl essence look to it for a good few months before it broke, not that im sure that has anything to do with it.
Just awaiting the delivery of the digitizer and hopefully I can repair it.
yeh mine had the pearl effect for a long time prior to it dyeing
ive followed the service manual and the video of the guy who gets stuck near the end, but how do you g et the screen out of the casing to get to the digitizer?
Its one hell of atight fit and i cant see anything o bvious.
Help
Hi Guys
Sorry about the late replies - had phoneline probs!!
Assuming you followed the instructions in the Service Manual to take the rest of the phone apart, you've just gotta be VERY careful and push the screen out from the back (where the Circuit Boards where) of the plastic frame. At first, it feels like it's not budging but be patient and it WILL start to push away.
It seems to be held in with some sort of hot glue or maybe a contact sort of adhesive and I didn't try it but some heat from something like a hair dryer may make the job easier.
Many people have cracked their LCD screen during the repair but as long as you're careful not to bend the screen too much when taking it out, you'll be fine.
I peeled the 3 layers (outer glass ones and then the Digitizer itself) off the LCD whilst removing it.
Good luck - it's really not that hard. Any more questions - just ask ;-)
ive got the phone apart to the point of the service manual/video
which part of the back do you push out? doesnt look obvious as to whats attached and what isnt
Once you get to the last stage (I thinks it's the Speaker Removal) you simply push on the metal protector of the LCD from the back. You will see small holes in the plastic of the back of the frame where you can push something blunt through and push very lightly on the LCD to push it out.
If I remember correctly, at the bottom of the phone where the circuit board with the vibrator and microphone on it was sitting, there is quite a large opening with the metal backing of the LCD visible through it. I started pushing there and gently went all around the phone in the various small holes dotted around it.
As I said above, it won't feel like it's working at first but it will - just be patient and not too heavy handed!
Hi,
In the drop test it showed when the HTC was dropped the speaker housing fell off. As I believe this part of the housing it glued on, how would be stick this back on if that happened to us?
fazzxx said:
Hi,
In the drop test it showed when the HTC was dropped the speaker housing fell off. As I believe this part of the housing it glued on, how would be stick this back on if that happened to us?
Click to expand...
Click to collapse
Could probably glue it back on? Get some super glue and bam right back on. Just an idea. :laugh:
Simply put the cover back on after heating the little glue htc has already there.
I love the fact they are removable because the back cover is very scratch resistant but the speaker ones damn they nick easily according to reviews. If they can be replaced just by gluing a new pair or spare parts that would be nice because thats only worth a couple dozen of dollars.
My Ex droped her Phone and it had Spider Webs all accross. Her Provider send it in to see what it would cost to fix. The Phone also would stop working correctly in the middle of calls.
It turns out buying a new one would have come cheaper atleast thats what came back as a answear.
So I decided to bite the apple and try replacing the Screen myself. My Ex was not happy because she thought with the second Problem it is not worth the effort to fix the Screen and maybe loose everything. My reasoning was that when the Spider Web Screen touches the Digitizer it will react strangely. So I went ahead and searched the web on how to do it. I ordered a Screen for $9 on ebay (free shipping) which came with a couple of Tools. More on those later.
One of the first Problems I found was that all instructions that I found showed the beginning and the end. But in the middle how the phone will look like when the glass is finaly taken off, I was unable to find much Information about it. Also doing it Redneck style without Special liquids and or a heat guns was no where to be found.
I decided to just try it. Disasembly is well documented and easy enough to do on this device. Atleast to the Point where most electronics are removed so that you can apply heat without too much problems. I decided on using a blow dryer to heat up the Display. I layed the Blow Dryer on the Counter turned it on and Held the phone up to it. Thinking if my fingers get too hot chances are it is too hot for the Display too.. Might be a little incaccurate to read the temperature like that but hey it worked. But soon after I started to remove the first pieces of broken glass I ran into Problems.
As per instructions I found, I put a Piece of tape accros the Screen so that the individuall pieces stayed ogether. That did not work at all for me. It just made the individual pieces push against the valuable digitizer below it. My next Problem was that the Tools that came with the replacement glass, especially the Little plastic Tools did not hold up to the Job und the tip was soon useless. I had to Switch to a Raizor blade. A couple of times I sliped and hit the Digitizer. Thinking oh well I guess I Need to get a new one. Luckely on the end it all worked out much better then I would have hoped. The left over glue I rubbed mostly off with my finger which worked out nicely. To clean it completely from ist glue took some time. The black rubber allong the side of the phone allso suffered. You might want to look out that that does not get riped out completely. I had enough left over so that the glass would sit on it good enough luckely.
Take a look at these Pictures and remember it works perfectly again for $9. While it is not for everyone to seperate a Glass from a Digitizer it is acctualy less fragile as you might think. The third Picture Shows you how it looked with all the scuff marks from taking off the glass. You can still see a few little marks on the end but hard to notice and much better then before. I am sure next time I will be more carefull and use the blade from the beginning on.
I got more Pictures and will improve this Thread for others that have to go through it. Feel free to PM me if you have any Questions. A list of other resources will also be included. This is only to explain and Show the bare state.
Reserved for links
Additional Screen Replacement Links:
Do you know if we can replace the metal frame on the side?
My device is bent. I mean. I fell on a rock with my device in my pocket and the rock directly hit the phone. Luckily I had a hsrd case and the device is still alive.
Sent from my GT-I9300 using Tapatalk
supreethms said:
Do you know if we can replace the metal frame on the side?
My device is bent. I mean. I fell on a rock with my device in my pocket and the rock directly hit the phone. Luckily I had a hsrd case and the device is still alive.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
You should be able to find a new Frame for a resonable Price. Now to remove the digitizer from the Frame that is another Story. Not sure if it was the Glue or what Held it in place but I could not figure out how to get that out. luckely the two Buttons at the bottom survived the Screen removal and so I did not hat to take the Digitizer out.
Useful information and explains why repair shops will usually only replace the complete assembly. Read many complaints that those cheap ebay screens are plastic and easily scratched, not genuine gorilla glass replacements?
Sent from my GT-I9300 using Tapatalk
http://www.ebay.co.uk/itm/150998824149?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
I've ordered one of these as mines a bit scuffed and what looks like a small crack in it.
boomboomer said:
Useful information and explains why repair shops will usually only replace the complete assembly. Read many complaints that those cheap ebay screens are plastic and easily scratched, not genuine gorilla glass replacements?
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
It is definetly cheaper then the original but if you have done it once. Chances are You will be able to do it again much easier. So if the $9 Glass only holds for example a Year. You can just replace it again. Or spend a little more for a original replacement glass.
Now I should Point out if the rubber seal around it gets damaged in the process and if the 3M Tape that should come with the Screen is placed wrong it will Impact the sensitivity of the sreen touches. I guess I did it right because my Ex is happy how it performs and that is saying allot.
madmackem said:
http://www.ebay.co.uk/itm/150998824149?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
I've ordered one of these as mines a bit scuffed and what looks like a small crack in it.
Click to expand...
Click to collapse
If you get down to removing the digitizer from the Frame take a couple of Pictures and post them here.
Recently got a GS5 and my mom doesn't have a phone right now so I'm handing my N4 down to her. The front glass is cracked and I wanted to get that fixed before I do. The digitizer and lcd are not broken, just the glass, everything else looks and functions fine. I guess what my question is, if I take it to a repair shop can they just replace the front glass or am I looking at around 100ish to replace it all? I'll be going in and getting quoted but just wanted to see if I got any input from here first, it will likely be a week or so before I take it anywhere due to this damn weather.
wareju said:
Recently got a GS5 and my mom doesn't have a phone right now so I'm handing my N4 down to her. The front glass is cracked and I wanted to get that fixed before I do. The digitizer and lcd are not broken, just the glass, everything else looks and functions fine. I guess what my question is, if I take it to a repair shop can they just replace the front glass or am I looking at around 100ish to replace it all? I'll be going in and getting quoted but just wanted to see if I got any input from here first, it will likely be a week or so before I take it anywhere due to this damn weather.
Click to expand...
Click to collapse
The same thing happened with my friends N4. The glass, digitizer and LCD all had to be replaced as they all come as one unit. Cannot get them separately.
Amazon/ebay has parts where you can just order the LCD/Digitizer etc, but then to separate them you have to have a heat gun etc. if you touch any part by mistake you will get finger prints or smudges permanently. So not a good idea unless you are one of those super careful person. http://www.ebay.com/itm/LG-Nexus-4-...D&orig_cvip=true&rt=nc&_trksid=p2047675.l2557
if you are handy, you can order the whole assembly online (amazon) for about 60 bucks or so) http://www.amazon.com/Touch-Screen-...r=8-1&keywords=nexus+4+lcd+screen+replacement
I personally got it replaced in So Flo for about 95 dollars + tax. I have been quoted about 140 at a chain fix up places.
bluesteve3 said:
The same thing happened with my friends N4. The glass, digitizer and LCD all had to be replaced as they all come as one unit. Cannot get them separately.
Click to expand...
Click to collapse
Sure they do. FYI, the "glass" is[ the digitizer. If "everything works", then technically all that needs replacing is the digitizer.
However, digitizer replacement is far from an easy thing to do. Not only does it require some specialist equipment (suction cups, heat gun, glue), you're probably going to screw it up unless you've done it before.
wareju said:
Recently got a GS5 and my mom doesn't have a phone right now so I'm handing my N4 down to her. The front glass is cracked and I wanted to get that fixed before I do. The digitizer and lcd are not broken, just the glass, everything else looks and functions fine. I guess what my question is, if I take it to a repair shop can they just replace the front glass or am I looking at around 100ish to replace it all? I'll be going in and getting quoted but just wanted to see if I got any input from here first, it will likely be a week or so before I take it anywhere due to this damn weather.
Click to expand...
Click to collapse
You can buy just the screen assembly off eBay for about $45, which has the digitizer already mated with the LCD. However, this requires removal from the bezel (again, a heat gun is recommended), then gluing the new one back in. For $60 you can get the entire front assembly (hey, brand new phone!), which is the easiest way to go about things. I'd also recommend buying a new battery ($20) and replacing the old, tired one while you've got the phone apart.
It's not all that difficult to do it yourself. You'll need a T5 TORX driver, something thin, sturdy and plastic to pry the phone halves apart (you can buy screen assemblies that come with all these tools), and some patience. Do everything on a fluffy white towel so the little screws don't get lost. The tricky part is the little rubber gasket thingy that goes over the proximity/light sensor module. Most people who have done a screen replacement have found that reassembly screws up the prox sensor, causing it to always read "near" (meaning during a call the screen will stay off and you can't hang up or use the dialer). The common fix is to put the gasket in backwards.
There are a number of threads here, some youtube videos, and a good teardown tutorial on ifixit.com.
I thought the digitizer was what recognized touch input? Either way I don't think I'll be doing any of this work myself, I'll just take it up somewhere for her for the repairs.
wareju said:
I thought the digitizer was what recognized touch input?
Click to expand...
Click to collapse
It is. It's built into the front panel of glass (which is made up of a bunch of different layers of stuff). Don't ask me how it works, it's all magic to me. But when you break the front glass, yet everything still works, that's the digitizer. If you look up digitizers on eBay you'll see that it's the front glass panel, with a cable and other electronic stuff attatched.
Either way I don't think I'll be doing any of this work myself, I'll just take it up somewhere for her for the repairs.
Click to expand...
Click to collapse
It's honestly not all that difficult to do yourself. Hell, send me the phone and screen assembly, and I'll do it for free. Seriously. I'll even through in a couple TPU cases I'm not using.
If you do take it somewhere for repairs, make sure you ask what they're doing. Replacing the screen assembly, or replacing the digitizer. For a $100 fee, it could be either. They could buy a $20 digitizer and the remaining $80 is in labor, but it'll take them a lot of time and effort, or it could be a $45/$60 screen assembly that takes far less time and effort to do. Personally, it costing the same, I'd rather have the screen assembly replaced, since replacing only the digitizer can lead to complications. Since it has to be reglued onto the LCD, you might get bubbles, dust/lint, dead spots, and that rainbow affect when you hold it in the light at the right angle.
Dear xda,
while being on holiday in South-East Asia, I got into some pretty heavy rain and my OnePlus 2 obviously didn't like the rain - the display seems to be broken since. Unfortunately I tried switching the phone on shortly after the water contact (because I needed it for navigation) and the display worked just fine while the phone seemed to be stuck software-wise (although now from a retrospective point of view it could have been that already then the display was somehow having issues).
I did put it in dry, uncooked rice just a few hours after the water contact and kept it there for a few days, with the SIM-Tray ejected and the back cover taken off. Still, after a few days, I tried switching it on again and I could notice that is was booting up just fine (I could see the capacitative buttons lighting up and even got some notification sounds after it booted up), but the display remained black
Back home I removed not only the SIM-Tray and the back cover but also the "inside cover" as well as the battery (it then looked like THIS) and put the phone back into rice for another 2 days. After that I reassambled the phone and tried switching it on again - still the display wasn't working.
After disassembling the phone again and taking the battery out, I put the remaining parts of the phone into the oven at about 45°C = 113°F for about 2h. But that didn't help either.
Is there any advice as how to maybe get my display working again? Maybe some cable or connection inside the phone that I could inspect or disconnect and reconnect? The process of buying a display on eBay and replacing the display seems to be rather complicated (due to the fact that the display is glued to the frame as from what I could see on ifixit.com) and I don't want to damage more than I already did while maybe the repair attempt doesn't help at all.
Does anyone have any experience/insight regarding how much it would cost me to open a repair ticket with OnePlus and let them repair/replace my display unit?
Guess it would cost around 200USD since the display is one of the costliest components in the phone. Not sure if it's only the display issue though. The water might have done some serious damage to the board itself.
100$ easily
My replacement screen cost me 30$ including shipping to Sweden, bought on Aliexpress, top notch quality nothing to complain on quality wise .
Skickat från min ONE A2003 via Tapatalk
pitrus- said:
My replacement screen cost me 30$ including shipping to Sweden, bought on Aliexpress, top notch quality nothing to complain on quality wise .
Skickat från min ONE A2003 via Tapatalk
Click to expand...
Click to collapse
I too considered buying a replacement screen on ebay or aliexpress. But I don't think I feel confident enough to take the necessary steps to replace the screen, because you seem to have to "unglue" the old screen and glue the new screen back on the frame (Sources: https://www.ifixit.com/Guide/OnePlus+2+Screen+Replacement/51922#s115570 and https://youtu.be/Q1b5Ut5kTRM?t=4m).
Is it easier to do than I think? Did you face any issues while replacing it? Can you see or feel a difference with the new screen compared to the original one (i.e. does it perfectly fit into the frame without protruding)?
gnaggwatschn said:
I too considered buying a replacement screen on ebay or aliexpress. But I don't think I feel confident enough to take the necessary steps to replace the screen, because you seem to have to "unglue" the old screen and glue the new screen back on the frame (Sources: https://www.ifixit.com/Guide/OnePlus+2+Screen+Replacement/51922#s115570 and https://youtu.be/Q1b5Ut5kTRM?t=4m).
Is it easier to do than I think? Did you face any issues while replacing it? Can you see or feel a difference with the new screen compared to the original one (i.e. does it perfectly fit into the frame without protruding)?
Click to expand...
Click to collapse
It was pretty straight forward and simple. I just applied heat to screen using a hairdryer and the used the included suction cup to gently loosed the screen from the adhesive using a credit hard to pry away the glue and then removed the connections to the screen and the touch-buttons and home button from the backside and then removed the screen. Then I moved over the home button and touch buttons to the new screen, applied some 3M adhesive strips on the frame after removing the old adhesive, put the screen back in place and reconnected the collectors, pushed the screen in place in the frame and heated it a bit too make sure the adhesive sticks and then screwed everything back in there and put on the back case. Done and done!
Ok I think I am gonny try tro buy a screen on aliexpress and replace it myself. Do you think this one should do?
well maybe you guys can help me out here i did the steps to replace the fingerprint sensor but now my screen wont stay glued , i have not been able to find the glue for the screen anyone can help with that by any chance ?
jera27 said:
well maybe you guys can help me out here i did the steps to replace the fingerprint sensor but now my screen wont stay glued , i have not been able to find the glue for the screen anyone can help with that by any chance ?
Click to expand...
Click to collapse
I would also like to know which kind of "3M adhesive strips" pitrus- used to keep the screen glued.
gnaggwatschn said:
I would also like to know which kind of "3M adhesive strips" pitrus- used to keep the screen glued.
Click to expand...
Click to collapse
I bought this one linked down here
3M Sticker Tape Sticker 1MM Double Side Adhesive For Cellphone Touch Screen LCD
http://s.aliexpress.com/UBbquiQf
(from AliExpress Android)
i will try it thanks how did you apply it ? did you have to do any modifications ? is the phone screen similar to its original state ? did you remove the previous glue ? soo many questions i wish there was a video on how to apply it on the phone , as of now my bottom half of the phone screen is unglued
jera27 said:
i will try it thanks how did you apply it ? did you have to do any modifications ? is the phone screen similar to its original state ? did you remove the previous glue ? soo many questions i wish there was a video on how to apply it on the phone , as of now my bottom half of the phone screen is unglued
Click to expand...
Click to collapse
For me, the old adhesive came off with the old screen. But I did some cleaning with alcohol just to be sure.