[Q] Troubles upgrading firmware to android 4.3 - Galaxy S 4 Q&A, Help & Troubleshooting

Please help - I have an unuseful phone right now.
I'm trying to update from 4.2.2 -> 4.3 using Odin software. I've tried several versions of Odin - but they all fail with following error:
*****
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9506XXUBML5_I9506FTMBML1_I9506XXUBMK7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Size)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
*****
After that my phone does not work, it will only boot to screen saying "Odin mode" ....... "UDC START".
The firmware is downloaded from sammobile.com: I9506XXUBML5_I9506FTMBML1_I9506XXUBMK7_HOME.tar.md5
I have to mention that I come from Denmark and the firmware is meant for "France (Orange)" - version 4.3 is not yet released for other european countries.
Afterwards I've also tried to reinstall 4.2.2 - but this one fails with following error:
*****
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> HOME_I9506XXUAMI3_I9506NEEAMI1_I9506XXUAMHD.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
*****
Sorry for putting same thread in two forums - was not able to move the first one.

Related

need help asap. cant reflash stock FW

i need help. i tried to flash a custom rom. it didnt work. so i thought go bad to stock. i have a i747 on rogers . odin3 keeps failing and im stumped. been googling all day and i cant figure it out can some help me please
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I747MVLALE8_I747MOYAALE8_20120523.225040 _REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Read ..
<ID:0/003> XmitData Fail..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
this is what i got
i got it finally. for some reason i had to take the .md5 off and just leave it .tar

[Q] Galaxy s4 GT-i9505

Hi Guys Hope you can rescue me. I had an automatic firmware update pending on my phone this morning so I ran it. It all seemed to go fine and it rebooted but I initially noticed that some desktop icons were missing. Then I noticed that you could not turn on wifi. I tried both from drop down and in settings but it would revert back to off each time. I googled it and found a few others had the problem and it was suggested that a hard reset may fix it. I did that but no joy.
Next step was to download odin 3.09 and a stock rom. This I did, the stock rom was a uko2 rom from here...hxxp://samsung-updates.com/latest-firmware/ I followed the tutorial to flash the rom and I get this (auth) Fail. here is a copy of the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK8_I9505O2UEMK1_I9505XXUEMK8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have searched on here and found some hits one was to load a pit file as well but it fails the same way the file I am loading is an MD5 file and I read somewhere it may have to be a ME7 file but I cant find that anywhere.Can some guru please help this frustrated user out as its doing my head in. Many thanks guys
If the OTA update received was android 4.4.2, maybe u updated your bootloader and you cant come back to android 4.3. You will have to flash through ODIN this firmware: HERE
Joku1981 said:
If the OTA update received was android 4.4.2, maybe u updated your bootloader and you cant come back to android 4.3. You will have to flash through ODIN this firmware: hxxp://rapidgator.net/file/e4df24422154b8c1320925eceb5d4f1f"]HERE
Click to expand...
Click to collapse
Thanks for this Joku1981. I am downloading it now and will update thread when I have tried it.
steve67474 said:
Thanks for this Joku1981. I am downloading it now and will update thread when I have tried it.
Click to expand...
Click to collapse
OK have downloaded and run the odin program it seemed to go fine but right at the endjust after the system load it failed again:crying: Here is the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505O2UFNA2_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> NON-HLOS.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/005> Added!!
Thought we cracked it
steve67474 said:
OK have downloaded and run the odin program it seemed to go fine but right at the endjust after the system load it failed again:crying: Here is the odin log...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505O2UFNA2_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> NON-HLOS.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/005> Added!!
Thought we cracked it
Click to expand...
Click to collapse
OK an update. I removed the battery for 5 mins and rerun and hey presto it worked. Great forum and thanks again for the support

Samsung GT-I9505 Stuck recovery

I wanted to update my samsung using odin when i tried it gave me this
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMJ5_I9505OJVEMJ5_I9505XXUEMJ5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
now im stuck at Emergency boot thing and it doesnt work
1. Try other USB ports, other pc or install again the Samsung drivers
2. This isn't the latest update anyway. It is: I9505XXUEMK9

[Q] Problems flashing SM-G900F

Hello, I update my samsung s5 SM-G900F to stock firmware - G900FXXU1BOA3_G900FOXA1BOA4_BTU
And now i cant install anything via Odin, just the same firmware. Cant install twrp or root, trying to install G900FDXU1BOA2_G900FOLB1BOA2_G900FDXU1BNL1 but i get error at the last sec.
Here's the log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900FDXU1BOA2_G900FOLB1BOA2_G900FDXU1BNL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Download Mode error in attached file
just installed G900FXXU1BOB7_G900FOXA1BOB7_BTU and it works as good as G900FXXU1BOA3.
is there any way to root G900FXXU1BOB7 ?
with autoroot i get failed. heres the log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-klte-kltexx-smg900f.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Help please :\

NEED HELP: S6 EDGE+ SM-G9287C STUCK (Error while updating software)

I hope you guys can help me.
So I tried going around my phone's system. I flashed using ODIN at first, then I got stuck on the "NO COMMAND ERROR". I put my phone again on Download Mode, but this time I got prompted this message, "An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software.", which I did, but it always says "SM-G9287C does not support initializing."
What could have I done wrong? Please help.
I tried using ODIN again, and I got this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3957 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3957 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1) - and it took me back to Smart Switch blah blah message
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..

Categories

Resources