Database Users

LG E900 Optimus7 Factory Menue Code

At an other board I read that the LG E900 Optimus7 phone provides a factory menue that could be activated with the following code:
##634# + Green Make Call Key
and then enter 277634#*# als password
I still don't know what is visible and changeable in factory menue. I would be intressted if there is also an netmonitor / field test display included.

From the menu are accessible different functions like hardware tests and usb mode change to enable thethering and USB modem (that one is a MUST if you want to flash the phone, by the way is Qualcomm QC mode...)
The hack began!

Indonesia nam programing SPH-P100

Tutorial Inject on Sprint Samsung Galaxy Tab-P100 SPH
Software:
- QPST 2.7 build 323
- QPST 2.7 build 215
- CDMA Workshop 2.7
Others that need to be prepared as well:
- Number Flexi/Esia/Smartfren ready diinject
- Akey (26 digits) is obtained from the gallery
- PRL (from galeri)
There are 4 steps so that you can use both text and data
- Unlock MSL / SPC CODE
- Setting Akey, MIN and MDN in order to do sms.
- Setting EVDO
- Final Setting
FIRST STEP (UNLOCK MSL / SPC CODE):
- Install the application from the Android Market: connectbot
In the lower left corner to move to the local type in any name and then let the Android will go into a black screen logo $ dng
- Type: getprop ril.MSL
MSN / SPC you I 6-digit code will appear
STEP TWO (SETTING Akey, PRL, MIN and MDN)
1. Install CDMA Workshop
- The first thing to do is to enter Akey, the 26-digit number given by the Custemer service when registering card number.
- How to enter into Gtab Akey must be signed in diag mode -> press # # 8778 # to enter the menu to the MODEM Phoneutil replace PDAto modem
Do not forget in a position Gtab USB debuging (go to settings - application - development - USB debuging)
- Note on the control panel - System - Hardware - Device Manager. Looking at what ports samsung gtab installed, (eg) on ​​COM port 7.
Open Workshop CDMA (CDMA WAS), select (eg) COM 7, and then press CONNECT.
Select READ
- Next you need to unlock Gtab to enter the MSL / SPC to do on the security tab and enter your SPC "6 digits" and press send, after a statement that HP can be unlocked then you are ready to enter Akey.
- In the CDMA workshop, typing or copy and paste the 26 digits Calculator Akey Akey on like the image above in the Dec, only 20 digits will be accepted Dec. text box is.
- Then automatically on Colom will appear Akey Hex Hex, you can check whether Akey terrsebut ESN is correct by entering the column and then click calc ESN, the checksum will pop up the last 6 digits of your 26-digit Akey, if true, then the Hex Akey already ready to use, copy and paste from the column Hex to Colom-Akey Cave and select write.
- your akey has been wrote on your device
2. Install QPST 2.7 build 3.2.3, plug into your PC and open Gtab QPSTConfiguration program.
- Select Add New Port, and select COM 7 (eg) corresponding config on CDMA WAS
- Select the Start Clients, select SERVICE PROGRAMMING and select an active phone
- Tap OK in the Phone Selection
- Click READ FROM PHONE, press OK if MSL Code appears.
On the Settings tab,
Slot Cycle Index: 2
Current NAM: NAM1
Auto NAM: unchecked
In Tab CDMA, fill in the following parameters:
NAM Name: Flexi
Directory #: No MDN (no flexi complete with area code, but the writing without the written numbers from 0 eg 02144445555 2144445555)
AOC: 2
CDMA
- MCC: 510
- 11_12: 00
- IMSI_S: No MIN (same as no MDN)
- Registration terminated (Checked All - Home SID - SID Foreign Foreign NID)
- Primary Channel A: 119
- Channel Primary B: 384
- Secondary Channel A: 78
- Channel Secondary B: 777
In Tab CDMA-2 (Optional)
NAM Name: Flexi
Directory #: No MDN (same as the MDN)
CDMA / True IMSI:
- MCC: 510
- 11_12: 00
- IMSI_S: No MIN (the same as the MDN)
- AOC: 2
In Tab AMPS Ignore
In Tab System
HOME SID / NID (Double click)
Fill with parameters:
- SID: 10 496
- NID: 65 535
Preferred Mode and so on selected Automatic
In Roam Tab
NAM Name: Flexi
Directory: No MDN (no flexi complete with area code, but the writing without the written numbers from 0 eg 02144445555 2144445555)
AOC: 2
Enter the PRL Preferred Roaming with the browse button click: select dr hard drive where you store the PRL
On the Display tab
Display Items:
- Banner: TELKOMFlexi (or may pake your name, ill effect to the existing parameters)
- Backlight: always on
INJECT ALREADY FINISHED.
Press the Write to Phone, ignore if there is an error. Then Gtab will restart, after restart should be able to sms.
STEP THREE (ACTIVATE EVDO)
Prior to this step is done please register in advance for your flexi mobile broadband it by typing PROMO (space) MONTHLY send to 2255
After that there will be information that your broadband has been active with the user id: [email protected] and password: your ESN
1. Through QPST 2.7 build 3.2.3
Gtab plug into your PC and open QPST Configuration program
Select Add New Port, and select COM 7 (eg) corresponding config on CDMA WAS
Clients select Start, select SERVICE PROGRAMMING and select an active phone
Press OK in the Phone Selection
Press the READ FROM PHONE, press OK if MSL Code appears.
2. In the M. IP tab
In the User Profile, select the profile 0, press the edit
- Fill in the parameters of the NAI: [email protected] (or [email protected] for smart isp)
- Fill in the parameters in the Tethered NAI: [email protected] (or [email protected] for smart isp)
- Home Address: 0.0.0.0
- Primary HA Address: 255.255.255.0
- Secondary HA Address: 0.0.0.0
- And press OK
In the User Profile, select a profile, repeat the process as the point a.
Mobile IP Behavior: Simple IP Only
3. On the PPP tab Config
Select the UM
In the PPP Authentication:
Contents Tethered NAI: [email protected] (or [email protected] for smart isp)
User ID: [email protected] (or [email protected] for smart isp)
Password: No. ESN
Check Optimized Dormant Handoff
Then Select AN
User ID: [email protected] (or [email protected] for smart isp)
Password: No. ESN
Others, are ignored.
4. In Tab RmNet
Select Device 0, click Edit ---> if no live Add
Check the "Enable Auto Connection", click OK
5. CLICK "wite to Phone"
Setting Gtab Completed.
After restarting the logo should appear on the notification of 3G already.
FINAL STEP
Unistal QPST 3.2.3 and install QPST 2.1.5
Go to the Service Programming menu.
Then on the PPP tab, fill in data such as fill on the PPP tab in QPST 2.7 Build 323.
After that write to phone again, then it will restart again gtab.
When finished restart, (For those who berOS Froyo) do a move like that anymore diawal2
Go to the application type in the search field NOTE # # 8778 # -> enter phoneutil, change the settings of the modem to the PDA.
thanks
source
http://www.kaskus.us/showthread.php?t=10869930

Need help for diagnostic codes (dial codes) ... No matches: !!!

I'm using T*Omina2 (SCH-M715) same as i8000 spec
After upgrade firmware to WM6.5, I cannot use any diagnostic codes (dial codes)
except for *#06# (check IMEI)
Other codes show as: No matches:
What is lack of in my WM ? and why I cannot use dial codes ?
Thanks for any help....

hidden menu (usb setting) (RMNET + DM + MODEM)

Hi everyone,
Guys i need to enter to inside the hide menu.
i try *#22745927 *#7284# but dint work
i dont now how can i enter the code but i need the change my usb settings (like RMNET + DM + MODEM)
sorry for my english. have a god days.

Try entering *#0808# on your dial pad.

Access Service Mode Band Selection

Hello Guys,
my phone is unroot. I dont want root
Firmware is G928CXXU2AOJ5
CSC KSA
How can a access the band selection, so i can set to lte band 20 only.
The Code i found
*#0011# (works for access service mode)
More - Press Back
More - Insert Q (don't work)
More - Insert 0000 (don't work)
also*
More - Insert Q0000 (don't work)
More - Insert Q1 (don't work)
More - Insert Q0 (don't work)
The Code
*#2263* also don't work.
Has anybody a idea or a code how do can i access the band selection without root?
I tried with phone info, but also don't work.
thanks