hi i have flashed cm902 rom it booted up but it dont like me cause makes eroros so i wanted ro reflash with old stock 2,3,3 and with recovery bootstrap i thinked what i wild came into recovery but it just hanged and now no recovery only white triangle with yelow! and only logo m, so maybe someone hav this problem earlier and can help me?cause now im searching half day of work for searching for solution.
thanks fo anny help
Dont worry. Do this. First use the wall charger and charge your phone for at least 30mins. So if your phone is off then it will charge till 70-80%. Check if it is charging by looking at the micro-usb port lighting up.
Now go to the White triangle with ! mark. Then press @ button. You will get options. Select erase data by pressing volume button and then clicking enter button on your keypad.
After the wipe has been done pull out battery. Then start RSD Lite on your computer. Put the battery to your phone. Now press both volume up and volume down together and then power button for 2secs. Leave power button. You will see it in bootloader.
Now load sbf file on RSD software and wait for it to recognize your phone. Then click start. Thats it. Your phone should be ok.
Hi there.
yesterday my pad told me there was a new version , so i updated it (at least tried)
Now when i start up my tab i get the following:
Enter into fastboot mode
You can press HOME + BACK to reboot device.
so i wated,, and waited and nothing happend when i press HOME + Back the device will restart but i will get the spalsh screen and aftrewards the same text again..
i checkd the form and found no body with this issue, i tried to re-install the firmware.
so i took the micro SD card Fomrated it (first time FAT 32 second time FAT) and put the dlload folder with the told version on it..
took my battery from my device placed it in again and pressed power button, device starts up and i get the same message again, and NO progress bar ..
please help me with this issue....
Bricked IDEOS S7
If you have not already got your S7 back to working condition you may try the following. I faced similar situation(s) some time back.
Requirement: External sdcard formatted in FAT32 and with dload directory with firmware installed on the unit. Use Indonesian stock firmware Froyo 2.2.2. Search around and it is easy to find. Make sure one of the files is unlmt.cfg and not any other. No glitches and all modules work fine. Since I have been experimenting with different ROMs and some personal mods I have flashed so many times, got lost and started all over again.
It is not necessary to have a battery installed but the charger must be connected.
1. Press Back and Power button together to startup and release Power button after few seconds. You should see a white bar. Release Back button.
2. After a few sec disconnect power charger.
3. Reconnect the charger. Press power button. You will a stable IDEOS for few sec and flashing will start.
At times you may have to repeat more than once to get it going. The blinking should be slow. If suddenly flashing stops after few bars or blinking frequency jacks up disconnect and try again.
Best of luck.
Hello guys, I'm new here and I hope you can help me out.
Let me make the story short.
My phone's screen broke and I replaced.
In that processes I lost the rubber that stick
to the panel of the volume. I was fine with that since my phone
in vibrate mode and I really don't use ring tone in my daily basis.
I tried to download Android 5.0 lollipop and flash it.
How did I get there? well since I did not have a volume button,
I downloaded an app that restarted my phone and got me into
fastboot mode without the key (I did got me where I wanted).
Then the problem was that in the middle of writing the .img
the freaking cheap bastard micro usb unplugged!!!
BAMM!! phone now is bricked, I cannot get into recovery/fastboot mode
since I cannot press the volume key and my phone is bricked.
I tried going through fastboot mode via my computer again,
but the computer doesn't recognize the device since it still
looping there forever at the google logo. I try installing USB
DRIVERS to see if I could do some "magic" haha. Got
error "This device cannot start ..." And still at the same problem.
I know I can get back to my recovery if order the part for the volume
key, I ordered the part to replace it, but trust me I was 3 weeks without
my phone and now this problem
Is there any way that I can get to fastboot mode to factory reset my phone
without volume key with a bricked forever looping a "google" logo ? :fingers-crossed: :fingers-crossed:
I appreciate any help.
vadeld said:
Hello guys, I'm new here and I hope you can help me out.
Let me make the story short.
My phone's screen broke and I replaced.
In that processes I lost the rubber that stick
to the panel of the volume. I was fine with that since my phone
in vibrate mode and I really don't use ring tone in my daily basis.
I tried to download Android 5.0 lollipop and flash it.
How did I get there? well since I did not have a volume button,
I downloaded an app that restarted my phone and got me into
fastboot mode without the key (I did got me where I wanted).
Then the problem was that in the middle of writing the .img
the freaking cheap bastard micro usb unplugged!!!
BAMM!! phone now is bricked, I cannot get into recovery/fastboot mode
since I cannot press the volume key and my phone is bricked.
I tried going through fastboot mode via my computer again,
but the computer doesn't recognize the device since it still
looping there forever at the google logo. I try installing USB
DRIVERS to see if I could do some "magic" haha. Got
error "This device cannot start ..." And still at the same problem.
I know I can get back to my recovery if order the part for the volume
key, I ordered the part to replace it, but trust me I was 3 weeks without
my phone and now this problem
Is there any way that I can get to fastboot mode to factory reset my phone
without volume key with a bricked forever looping a "google" logo ? :fingers-crossed: :fingers-crossed:
I appreciate any help.
Click to expand...
Click to collapse
Im not sure why your text is like this? But paraphrasing buddy comes a long way
Just hold the power button, until it dies, or just let it die in general since your volume button (You only need Vol down and Power) to power it off completely. Since your Volume keys are gone, the best solution is to wait for the replacement before doing so, unless you can get the contact keys to trigger the Volume button, you're in a loss atm. No OS or Volume keys means you can't trigger ADB commands or boot into fastboot. Just wait it out I guess?
Hi,
Have no luck with this Tabby.
Tab was lagging like hell, so I just did a reboot (long press power button and select reboot). Now the Tab doest boot anymore. if I connect a USB cable it tries to start but a blue box appears "certificate verification failed" If I press a volume button a startup.nsh will be loaded an I see a shell. Thats all. but I cannot enter any command, hence there is no keyboard.
A few months ago I had the problem that the tab didnt boot anymore also out of nowhere but hung up in fastboot starting... I disassembled the tab, soldered wires onto the bios chip and programmed with a bios file from an old KK FW version I downloaded. after that the Tab booted normal. Soldering was a pain in the ass, and I really don´t want to do that again. Maybe it will not help anyway.
What happened to that tabby and what can I do?
Hello dear xda community
I have a px6 device from the company "Wondefoo" installed in my Mazda (without any hard buttons). It worked so far so good, but ZLink (Apple Carplay) didn't work, so I tried to fix this. To do that, I rooted the device, uninstalled the "ZLink" app and reinstalled a newer version. Then I tried to reboot. And then my problems started:
The device doesn't boot anymore. It tries to start up, I can see the Android 10 boot logo ("multi-media on-vehicle Navigation System" screen), but after about one minute, this logo disappears and the screen remains black.
OK, easy fix --> Just go into recovery mode and reset the device. But here's the big problem: I can't get into recovery mode.
Here's what I tried:
1. Ignition off and on --> Screen still black
2. Press "Reset" button (my device only has this one physical button) --> Boot process started again, but same outcome
3. Unmount the device, plug the power out, wait an hour, plug it in again and try again --> Boot process started again, but same outcome
4. Tried to connect with adb over Wi-Fi to the device (used the last known IP address) --> Connection timeout, Wi-Fi probably not started yet
5. Press&Hold "Reset" button until lights beign to flash to get into recovery mode --> Lights never flash because the "Reset" button somehow breaks the power circuit and when I release it, the device gets power again and boot process starts again with same outcome
6. Press&Hold "Reset" button for a minute, then release it, then press it again quickly within 1sec --> Boot process started again, same outcome
7. Tab with 5 fingers on the boot logo --> Nothing happened
8. Attached keyboard and pressed "Alt" + "PrintScreen" + "I" all the time --> Nothing happens. Keyboard is with RGB LEDs, so I saw it was active when the boot logo was displayed... Then, the LEDs on my keyboard turned off which was telling me that there is no keyboard input possible anymore
9. I even tried this: https://forum.xda-developers.com/t/new-method-enter-recovery-no-physical-buttons.4013453/ --> I just have one similar cable, not two as described in this post... So I put everything together again and just tried again --> Boot process started again, same outcome
Well... Is there any option left? I'm thinking about buying a USB male-to-male cable and try again with adb, but everyone tells me that I need to get into recovery mode first which I really can't
* Is there any other way to get into recovery mode? Maybe with my keyboard?
* Does anyone have another idea what I could try? Maybe without recovery mode?
Thanks in advance and cheers
T
As you said:
1. Ignition off and on
2.Have ready the needle for reset and do that instantly as you see the boot logo.
Once device restarted, wait until will see the boot logo again and pull out the ignition key.
3. Put in an USB socket a pen drive with the right firmware
4. Put back the ignition key and let it in ON position, without starting the engine. The update process will start, have a bit of patience until will finish. The device will restart at the end of the update, and straight after the boot logo, shortly press the reset button.
With a bit of luck, will have a fresh firmware on your device.
Thanks for your quick answer.
I tried what you said several times, but unfortunately I always end up on the black screen, no matter what I try.
My usb stick flashes quickly during the boot process, but nothing happens with it.
I also tried with an USB male-to-male cable and connect via adb, but it won‘t connect...
t-to-the-a said:
5. Press&Hold "Reset" button until lights beign to flash to get into recovery mode --> Lights never flash because the "Reset" button somehow breaks the power circuit and when I release it, the device gets power again and boot process starts again with same outcome
Click to expand...
Click to collapse
Are you sure you are holding the reset button for long enough?
On my machine (Dasaita) you hold the reset and the machine turns off... but you have to keep holding it even after it has turned off. Could be upwards of 1.5 minutes. Once the lights flash (and finished flashing), release and press one more time within 3 seconds.
Thank you for this idea. I have tried 30 seconds, but no more until today...
Now I tried with 1min, 2mins, even 3mins, but nothing happens.. I think the power is immediately cut as soon as I press the reset button. So there is probably no way to fix this easily
I also contacted the seller, but they have a talent to not understand my question. I just get answers like "press the reset button 2 sec and then everything is fixed" or "plug in the USB drive with the new ROM and press update" - of course that doesn't help.
Well I guess I'm left with one last thing: Throw this device away and buy a new one. Not from Wondefoo anymore of course, and hopefully with a working reset button.
I have the same issue. What did you end up doing?
Where did you buy your unit from?