I have searched and used as much google fu as I know how, so if I've missed the obvious I'm sorry.
Phone: Att Galaxy S4 SGH-I337
Running: I think stock 4.2.2 that was rooted.
Problem: currently will only get to the att logo then moves no further. Odin always fails to get me back to stock.
Cause of problem: Mostly likely me. I was attempting to unroot my phone using ODIN following a tutorial on galaxys4root.com.
Things I have tried: 6 different USB cords, 4 PCs 1 mac, Odin 3.07 and Odin 1.85, Several different sources for stock roms.
Notes: When I try to use the power button volume button method of booting to recovery it just goes to the odin download screen. This has been happening for a day or so that I've noticed.
Output from odin: <OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Output from phone: Odin Mode
Produc Name: SGH-I337
Current Binary: Samsung Offical
System Status: Custom
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
START [224, 1440]
SW REV. CHECK FAIL : fused : 2, Binary : 1
the output is pretty much the same regardless of odin computer or cable.
Any help would be greatly appreciated.
Thanks
#1. did you have usb debugging enabled before booting into download mode?
#2. do you know what firmware version was on the device when you got it (MDB, MDL, MF3)?
#3. booting into recovery is volume up + home + power. when your device vibrates, release just the power button. not sure if this is what you've been doing or if this will even benefit you right now.
Can you get into recovery? Were you stock beforehand or did you have a custom rom? If you can get into recovery do a factory reset. I'm guessing you got the mf3 update and that's why odin is not working.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
xBeerdroiDx
1. It was enabled the last time I was able to boot up.
2. Sadly no.
3. Tried a million on a thousand times. Every way which way i could think. The blue text pops up for a fraction of a second then it dumps off into odin mode.
jd1639
Can't get to recovery. Stock rooted. wasn't even aware i got the update. noobed it up.
Idk what else you can do. Try to see if kies will do an emergency restore. After that I'm out of ideas.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Try an older version of odin like 1.85 get into download mode then try to flash a custom recovery?
Sent from my SAMSUNG-SGH-I337 using xda premium
Are you releasing all the buttons as soon as you see the blue text come up--like immediately
@BD could OP have lost recovery and maybe dd the twrp recovery image. assuming adb recognizes phone
rugmankc said:
Are you releasing all the buttons as soon as you see the blue text come up--like immediately
@BD could OP have lost recovery and maybe dd the twrp recovery image. assuming adb recognizes phone
Click to expand...
Click to collapse
Immediately, promise, the text flash up for less than time that it would take to read it. just long enough for you to see something blue. I haven't been able to get it into recovery mode. Up until recently it wasn't a problem.
do you have adb access to phone to see if phone is recognized thru windows command terminal
Rabidbot, you got some serious fire power here helping you. I hope you're successful. Good luck to you.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
rugmankc said:
do you have adb access to phone to see if phone is recognized thru windows command terminal
Click to expand...
Click to collapse
Working on trying to figure that out now.
UPDATE It isn't coming up in the list of attached devices.
ok, i don't know if phone can be recognized in your situation. It has to have had usb debugging enabled.
rugmankc said:
Are you releasing all the buttons as soon as you see the blue text come up--like immediately
@BD could OP have lost recovery and maybe dd the twrp recovery image. assuming adb recognizes phone
Click to expand...
Click to collapse
I would be curious to know if adb in fact does recognize the phone. If so, the OP might be more successful flashing stock recovery and seeing if a factory reset clears it up. Sound like that partition is borked?
xBeerdroiDx said:
I would be curious to know if adb in fact does recognize the phone. If so, the OP might be more successful flashing stock recovery and seeing if a factory reset clears it up. Sound like that partition is borked?
Click to expand...
Click to collapse
Agreed--
xBeerdroiDx said:
I would be curious to know if adb in fact does recognize the phone. If so, the OP might be more successful flashing stock recovery and seeing if a factory reset clears it up. Sound like that partition is borked?
Click to expand...
Click to collapse
Doesn't seem to be recognized.
rabidbot said:
SW REV. CHECK FAIL : fused : 2, Binary : 1
Click to expand...
Click to collapse
I believe you were on MF3 when it died.
Fused:2 means the qfuse was blown by the mf3 update
Binary:1 means the software you're attempting to flash matches a qfuse level 1 (mdl and lower)
I think it's either a samsung warranty replacement or wait for mf3 on kies.
Sent from my SAMSUNG-SGH-I337 using xda premium
Hi,
I would say google these terms to get a better idea of what you need to do to fix your phone:
START [224, 1440]
SW REV. CHECK FAIL : fused : 2, Binary : 1
I am pretty sure it sounds like you somehow flashed the new MF3 update and now it is not possible to Odin an AMDL image onto phone now due to blown Qfuse in the MF3 update. Here is example of what the above terms mean:
http://forum.xda-developers.com/showpost.php?p=43484436&postcount=370
Possible fix? (Not quite the same situation as you are in, but if you try to use Kies to restore your phone, I bet you will be in this same position maybe?)
http://forum.xda-developers.com/showthread.php?t=2360859
Sorry I couldn't provide a definite, quick fix, but I hope this helps point you in the right direction at least!
rabidbot said:
Working on trying to figure that out now.
UPDATE It isn't coming up in the list of attached devices.
Click to expand...
Click to collapse
ok based on other's comments, you may not have a quick solution. i missed the part about "fuse" -- sorry
did you have adb working before as in are your drivers installed. if no drivers, dl kies to get drivers. then uninstall it and try again
sounds like you are familiar with running adb commands?
Klown80 said:
Hi,
I would say google these terms to get a better idea of what you need to do to fix your phone:
START [224, 1440]
SW REV. CHECK FAIL : fused : 2, Binary : 1
I am pretty sure it sounds like you somehow flashed the new MF3 update and now it is not possible to Odin an AMDL image onto phone now due to blown Qfuse in the MF3 update. Here is example of what the above terms mean:
http://forum.xda-developers.com/showpost.php?p=43484436&postcount=370
Possible fix? (Not quite the same situation as you are in, but if you try to use Kies to restore your phone, I bet you will be in this same position maybe?)
http://forum.xda-developers.com/showthread.php?t=2360859
Sorry I couldn't provide a definite, quick fix, but I hope this helps point you in the right direction at least!
Click to expand...
Click to collapse
This is the output from odin. It was successful but my phone still doesn't boot past the att logo.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF3_BTL_FIX.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> rpm.mbn
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> tz.mbn
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
rugmankc said:
ok based on other's comments, you may not have a quick solution. i missed the part about "fuse" -- sorry
did you have adb working before as in are your drivers installed. if no drivers, dl kies to get drivers. then uninstall it and try again
sounds like you are familiar with running adb commands?
Click to expand...
Click to collapse
I got the Drives are installed and have worked before. still nothing in the device list.
Related
So... Like a fool, having successfully rooted my phone a couple of days ago on the I9505XXUBMGA firmware, I saw this appear in Kies when I plugged my phone into Kies this morning. I thought (yeah you know where this is heading) "Oooh shiny new update, must download".
So although I had root I didn't think it would be a problem I'd just re-root afterwards. And hey if it didn't work I'd just downgrade the firmware and repeat the original process.
Trouble is I now have a message saying "SuperSU has been forced to stop for an unauthorized attempt to access system in your device. It may be solved by the policy update service. It may be safe to delete an application obtained from an unauthorized route. Check now?". I then have the option to not show for 30 days and then Cancel, Update or OK. Trouble is now when I attempt to revert the firmware back to an earlier version.
So now when I go into Download mode I see:
Code:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
If I try and Odin a new (stock) firmware on I get a write error from Odin and on the I9505 I get the following below the above text:
Code:
START [224, 1440]
SW REV. CHECK FAIL : fused: 2, Binary : 1
Odin shows:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMGA_I9505OXXBMG3_I9505XXUBMGA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
So, kind of stuck now. If the phone tries to restart I get the message: "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.". For a while I couldn't get the phone to boot, and Kies doesn't see the phone, but oddly re-partitioning via Odin using the PIT file means the phone will boot. From there I still get the SuperSU message but can switch it off and get into recovery mode, does that mean there is a chance I can re-flash things via adb / fastboot?
Yep I'm an idiot for trying and being the Guinea pig, but as I don't know how to proceed if anyone wants to help out and see if we can get it back and un "Knoxed" (which I think might be the issue) I'm more than happy to help.
Limitations currently are that I am running Windows XP 32-bit via Parallels virtual machine. The unbricking steps seem to indicate needing a 64-bit machine? I could probably do that but would have to get hold of and install 64-bit Windows 7 as a VM.
In terms of Android hacking I'm a noob, but can follow instructions, and am comfortable with a Unix/Linux command line if that's any help to anyone who wants to take pity on me...
OP, I'm in the same position as you, however I'm still stuck in download mode. Can you tell me EXACTLY what you did with Odin to manage to be able to boot the phone up again? I'd rather be able to use it un-rooted for now than to not use it at all!
Boolean = True said:
OP, I'm in the same position as you, however I'm still stuck in download mode. Can you tell me EXACTLY what you did with Odin to manage to be able to boot the phone up again? I'd rather be able to use it un-rooted for now than to not use it at all!
Click to expand...
Click to collapse
So, assuming you are stuck at the "there was a problem stage" you need to turn off the phone and get it into download mode (hold volume down, home + power - I guess you know this but just in case). I found this a bit fiddly I think because the phone is auto-rebooting, so try pressing power off and just holding the volume down and home buttons.
Then in Odin I used the PIT file listed in this thread. In the 'Re-partition' section and the boxes for Auto Reboot, Re-Partition, and F. Reset Time were all checked. I left all the other boxes empty (including the Files section). Click start and then after a while the phone reboots. It take a minute or two but if you see the Samsung logo it should boot.
Hope that helps... now to find a way around the MH1 firmware... oh and glad it wasn't just me that was daft enough to go and try it.
No, not just you mate. I had a hell of a time last night. Flash pre-rooted MGG firmware via odin, which bootlooped. I couldn't flash MGA firmware again.
So I flashed Stock MGG which booted but the security measures implemented have stopped me from changing my font using ifont.
I have now flashed MH8 over the top and it's working better than MGG, but still can't use some apps due to the new security measures.
I was able to flash Omega V10 from TWRP and it booted fine, but no wifi and I'm unable to flash LTE modem to correct it.
Looks like I'm stuck unrooted on MH8 for the time being.
There are some instructions on this thread on how to root this firmware, they're a bit lengthy tho.
http://forum.xda-developers.com/showthread.php?p=45283966
Sent from my GT-I9505 using Tapatalk 4
Bugger.
To add insult to injury it appears that WiFi is now no longer working either.
I'll look into the post you linked too, but I can't see how it will update that all, i.e. it says to use Odin which currently fails for me.
Odin doesn't fail for me when flashing kernels or recoveries, just when I try and flash full firmware earlier than MGG which includes the bootloader.
Flash full MH8 firmware from samfirmware, I have no issues except for the security problems.
Sent from my GT-I9505 using Tapatalk 4
In the odin output, the "fused: 2" shows the update has blown a q-fuse. You won't be able to odin an earlier firmware.
jd1639 said:
In the odin output, the "fused: 2" shows the update has blown a q-fuse. You won't be able to odin an earlier firmware.
Click to expand...
Click to collapse
No I know, but you can still flash recovery and modem etc. Is it failing at trying to flash older bootloader?
Sent from my GT-I9505 using Tapatalk 4
shrubz said:
No I know, but you can still flash recovery and modem etc. Is it failing at trying to flash older bootloader?
Sent from my GT-I9505 using Tapatalk 4
Click to expand...
Click to collapse
Yes, I hadn't realised that flashing the same or newer would work (it does). But WiFi is still borked... any ideas?
Tiny amount of progress, more out of hope I tried to flash a pre-rooted ROM - obviously this didn't work, but when I reflashed MH8 again I noticed the device made the start up sound (which it hadn't been) and WiFi is now working.
As a bonus if I go into Device Status it is now showing as Official, which is nice!
I think I'll leave it there for now, but will keep an eye out for progress, hopefully the bootloader will be "fixed" in due course.
Chainfire is working on a fix for CF-Root. So hopefully all will be good soon.
Sent from my GT-I9505 using Tapatalk 4
Hi guys, long time lurker here anyway i've always flashed my S4 with odin and not a single problem always flashed STOCK firmwares
but today i recently discovered a new firmware on the list for the GT-I9500 Exynos Octa (version) - this firmware to be in fact I9500ZNUCMI1
but now its bombed... it hanged and hanged at booting for 20 min then it shut it self off turned it back on 'the firmware encounter a problem' message popped up... i cannot go into recovery mode AT ALL (just download mode) so i thought i will flash my previous stock firmware known as I9500XXUBMG9 but now i cant even do that..... odin just gives me a god damn fail - FOR THE LOVE OF ANDROID HELP ME
- Kies is not running in the background
- USB connections are fine
- Cables are fine
So do i have to fear this is the end ? lol i cannot believe this happened to me on a STOCK firmware.... (lucky for me... all my stuff is backed up on sd)
Any help would be greatly appreciated
lethcore said:
Hi guys, long time lurker here anyway i've always flashed my S4 with odin and not a single problem always flashed STOCK firmwares
but today i recently discovered a new firmware on the list for the GT-I9500 Exynos Octa (version) - this firmware to be in fact I9500ZNUCMI1
but now its bombed... it hanged and hanged at booting for 20 min then it shut it self off turned it back on 'the firmware encounter a problem' message popped up... i cannot go into recovery mode AT ALL (just download mode) so i thought i will flash my previous stock firmware known as I9500XXUBMG9 but now i cant even do that..... odin just gives me a god damn fail - FOR THE LOVE OF ANDROID HELP ME
- Kies is not running in the background
- USB connections are fine
- Cables are fine
So do i have to fear this is the end ? lol i cannot believe this happened to me on a STOCK firmware.... (lucky for me... all my stuff is backed up on sd)
Any help would be greatly appreciated
Click to expand...
Click to collapse
If you can get into Download mode, all hope is not lost. Uninstall and resinstall drivers, Odin, etc. reboot.
Odin back to stock, immediately boot into stock recovery, wipe data, reboot.
Done.
donalgodon said:
If you can get into Download mode, all hope is not lost. Uninstall and resinstall drivers, Odin, etc. reboot.
Odin back to stock, immediately boot into stock recovery, wipe data, reboot.
Done.
Click to expand...
Click to collapse
Thx for reply
Still says FAIL when i try to flash I9500XXUBMG9 what am i doing wrong ?
rebooted laptop twice plug in S4 via usb says unknown device when in download mode but odin reconise it flash it and nothing happens on the screen then i get the big fat RED FAIL ............... AHHH
lethcore said:
Thx for reply
Still says FAIL when i try to flash I9500XXUBMG9 what am i doing wrong ?
rebooted laptop twice plug in S4 via usb says unknown device when in download mode but odin reconise it flash it and nothing happens on the screen then i get the big fat RED FAIL ............... AHHH
Click to expand...
Click to collapse
The good news is that Download mode is still working. AS long as that's the case, you can get it back. Just keep trying. Switch PCs, switch cables, switch ports, re download a different stock ROM, etc. do whatever it takes to try every variable you can think of.
Eventually, you'll find what's causing it and the ROM will flash successfully. When that happens, get immediately into recovery and wipe data.
(Remove the battery after it flashes, but it back in and hold vol-up+home+power.)
After the data wipe....
Reboot.
Like I said, Download mode means you can find a way to flash, but working with Odin to resolve these issues can sometimes be a PITA. I've had the same thing myself before. Just don't give up. Try to stay calm, and work your way through it. You'll get it eventually.
Edit: Just noticed that you flashed a CHINA firmware. (Why? ) You may be facing this issue because (I think) they use a different pit. There's a thread devoted to resurrecting the device with pit. Maybe check it out.
lethcore said:
Thx for reply
Still says FAIL when i try to flash I9500XXUBMG9 what am i doing wrong ?
rebooted laptop twice plug in S4 via usb says unknown device when in download mode but odin reconise it flash it and nothing happens on the screen then i get the big fat RED FAIL ............... AHHH
Click to expand...
Click to collapse
dont flash China or Hong kong firmwares.
please post odin progression
samersh72 said:
dont flash China or Hong kong firmwares.
please post odin progression
Click to expand...
Click to collapse
Nothing to post just says 'completed' but its failed.... i'll remember this next time stay away from china/hong kong firmwares...
im still tyring now and will let you guys/girls know how it pans out! wish me luck!
lethcore said:
Nothing to post just says 'completed' but its failed.... i'll remember this next time stay away from china/hong kong firmwares...
im still tyring now and will let you guys/girls know how it pans out! wish me luck!
Click to expand...
Click to collapse
INFO HERE
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500XXUBMG9_I9500OJVBMG9_I9500XXUBMG9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> param.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> persdata.img
<ID:0/005> system.img
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
lethcore said:
INFO HERE
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500XXUBMG9_I9500OJVBMG9_I9500XXUBMG9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> param.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> persdata.img
<ID:0/005> system.img
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
recovery is flashed, try to boot into it and make the wipe then re-flash stock, re-wipe.
if not, flash a custom recovery, format system, cache, re-flash stock, re-wipe
@donalgodon
Why ? well i got the I9500 in hong kong (im actually based in china now) (not Chinese though) thought i'll see some nice changes? but seems i fK'ed the phone.... pit? i haven't a clue man pit number? think i've KILLED HER... lol (i never knew the dangers of Chinese firmware) - wont be going down that route again.
@samersh72
Are you sure? i cannot get into 'recover' mode... the phone just hands at 'Firmware upgrade encounted an issue please select kies & try again
i canm only enter download mode.... when i try to enter recover mode it just flashes at the firmware message.
lethcore said:
@samersh72
Are you sure? i cannot get into 'recover' mode... the phone just hands at 'Firmware upgrade encounted an issue please select kies & try again
i canm only enter download mode.... when i try to enter recover mode it just flashes at the firmware message.
Click to expand...
Click to collapse
flash custom recovery,
if not see my signature for flashing right pit with the firmware
samersh72 said:
flash custom recovery,
if not see my signature for flashing right pit with the firmware
Click to expand...
Click to collapse
Well i just grabbed a I9500 pit file and have my stock firmware just add these 2 to odin and click start? that simple or ??
lethcore said:
Well i just grabbed a I9500 pit file and have my stock firmware just add these 2 to odin and click start? that simple or ??
Click to expand...
Click to collapse
yes, make sure that you are using the right pit, put it in "pit" window in odin, and the firmware in "pda", make sure "re-partition" is ticked, start.
samersh72 said:
yes, make sure that you are using the right pit, put it in "pit" window in odin, and the firmware in "pda", make sure "re-partition" is ticked, start.
Click to expand...
Click to collapse
Well you be happy to know
installed the previous firmware and that pit file for I9500 from your sig and everything seems well... booted correctly nothing lost all seems good to early to tell but will keep you informed !
THANK YOU!!!
S4 I9505
Problem:
Start up screen top left corner shows:
kernel is not seandroid enforcing
Hangs up or Reboots.
I updated my S4 to Version: I9505XXUEMKE
Then I used Odin to Flash a Root with Stock recovery & SU, something went WRONG!
Knox is now 0x1, which should not have happened, but what can I say.
BaM, I got the Reboots & Hang ups.
But, I still could get into Recovery & Download Mode!
SO HERE IS THE FIX:
1. Download, Odin 3 - THx 2 - daerragh
--- I used Ver.: Odin 3.07
2. Download, http://www.sammobile.com/firmwares/2/
--- Register
--- And download your Firmware, if you know which you had before it crashed choose that one otherwise Upgrade to latest.
--- For me it was the latest version - I9505XXUEMKE ---- THx 2 -- Repulsa for the tip.
3. Start Odin 3.07 --- [Should it "FAIL" Read note at the Bottom #6].
--- Make sure - Auto Reboot & F. Reset Time are checked - Nothing else.
--- Click on PDA choose your Firmware file in my case "I9505XXUEMKE"
--- this can take a minute or two, WAIT, the PDA will check mark itself.
4. To start Turn off your phone completely ! Now hold following buttons to get into Download Mode,
--- Volume Down
--- Home
--- and last Power
--- S4 will enter into DL Mode
Seeing you have already tried to root you phone, you should have you Samsung USB drivers.
5. Press Start
--- This will take time, after it Reboot itself,
--- remove the USB Cabel & wait
--- at least 5 minutes don't remember how long, I came back after 5 Minutes and it was done,
---------- so then if everything went well for you, have fun :good: .
6. FAIL
--- Should it Fail while uploading to your phone,
--- A. Remove Battery
--- B. Remove USB cabel
--- C. Restart.
--- Should it Fail again (which happend to me), then Do A. B. C. again.
--- and this time Touch your screen about every minute.
I Know that sounds weird, but it worked for me maybe something to do with "Stand by? no clue".
If this has help you in anyway please hit that :good: Thanks Bottun
I AM NOT RESPONSIBLE for anything happening to your phone as a result of you flashing this Rom.
[Help Please] TMO-S4- Kernel is not seandroid enforcing
Hello,
Let me start off by saying, I'm a complete newbie when it comes to rooting (Infact - It took me a few days to even convince myself to do this) and I did look around for several guilds on how to remove this error (Downloaded Odin - Got Stock TAR.MD5) But I still get this error on my phone when I start the phone, it wouldn't be much of a probelm, except it hangs for a while and then restarts.) It also gets stuck for a long time at the T-Mobile load screen. The Wifi Wont turn on their... Please Help.
Galaxy S4: SGH-M919
T-Mobile...
I'm not an expert in Android OS but I think this is not an error. It is more of a notification that the STOCK KERNEL has been change to a CUSTOM one.
eclpsues said:
I'm not an expert in Android OS but I think this is not an error. It is more of a notification that the STOCK KERNEL has been change to a CUSTOM one.
Click to expand...
Click to collapse
You are right :highfive:
Hi guys
A friend and I tried to update my rooted Samsung S4 i9505 to the official kitkat version. Had the unofficial one before. Unfortunatly we didn't turn on the usb debugging and there wasn't enough space on my memory card. After removing the data from the sd card it still didn't work (usb debuging?). My friend then tried to install a custom rom of some sort (I'm the noob here. He has some skills). No whenever I try to start my cell up the message KERNAL IS NOT SEANDROID ENFORCING pops up in the top left corner. Can I turn on the usb debugging from the pc? What should I do?
Thanks
illias9 said:
Hi guys
A friend and I tried to update my rooted Samsung S4 i9505 to the official kitkat version. Had the unofficial one before. Unfortunatly we didn't turn on the usb debugging and there wasn't enough space on my memory card. After removing the data from the sd card it still didn't work (usb debuging?). My friend then tried to install a custom rom of some sort (I'm the noob here. He has some skills). No whenever I try to start my cell up the message KERNAL IS NOT SEANDROID ENFORCING pops up in the top left corner. Can I turn on the usb debugging from the pc? What should I do?
Thanks
Click to expand...
Click to collapse
I tried to install the Gummy Rom but I got the same problem. It gets stuck in the rebooting or something. It wont pass the samsung start screen. What should I do?
Tried all of the above and no go.
Hi i have CM on my Australia XSA Samsung 19505 and i am trying to get it back to stock though when i try to flash it in Odin it fails all the time i cant get into recovery though i am able to access download mode.
I am using Odin 3.09 with the correct stock rom for my device and when i run it i get this error message
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK9_I9505XSAEMK3_I9505XXUEMK9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sbl1.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And on my device is error message
start [224,1440]
sw rev check fail fused 4 binary 3.
I also have the "kernel is not seandroid enforcing" message.
When i restart my device i get an error message "Firmware upgrade encountered an issue please select recovery mode in kies and try again"
I have tried to use Kies both versions and it doesn't work, The only way to get it to work is flash CWM which allows me back into my device.
Any ideas on how to get back to stock Thanks?
Natza09 said:
Hi i have CM on my Australia XSA Samsung 19505 and i am trying to get it back to stock though when i try to flash it in Odin it fails all the time i cant get into recovery though i am able to access download mode.
I am using Odin 3.09 with the correct stock rom for my device and when i run it i get this error message
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK9_I9505XSAEMK3_I9505XXUEMK9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sbl1.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And on my device is error message
start [224,1440]
sw rev check fail fused 4 binary 3.
I also have the "kernel is not seandroid enforcing" message.
When i restart my device i get an error message "Firmware upgrade encountered an issue please select recovery mode in kies and try again"
I have tried to use Kies both versions and it doesn't work, The only way to get it to work is flash CWM which allows me back into my device.
Any ideas on how to get back to stock Thanks?
Click to expand...
Click to collapse
Use a different usb port. Always use the ports on the back of your pc not the ones on the front.
Lennyz1988 said:
Use a different usb port. Always use the ports on the back of your pc not the ones on the front.
Click to expand...
Click to collapse
Thanks Lennyz for the reply, I tried the back usb 2.0 and 3.0 and both failed with the same error message as originally posted. Can i just restore the kernel some how and will that fix the issue?
Natza09 said:
Thanks Lennyz for the reply, I tried the back usb 2.0 and 3.0 and both failed with the same error message as originally posted. Can i just restore the kernel some how and will that fix the issue?
Click to expand...
Click to collapse
I think I know what you did. You try to flash an older stock firmware on to your device. Pick a newer firmware because downgrading is not possible.
Lennyz1988 said:
I think I know what you did. You try to flash an older stock firmware on to your device. Pick a newer firmware because downgrading is not possible.
Click to expand...
Click to collapse
I have tried to flash several Roms that are 4.4 and that are compatible with my device using clock work mod and it doesn't work as i keep getting a Status 7 error which i have found a possible fix for here in the forum i will attempt to resolve and report back.
---------- Post added at 11:40 PM ---------- Previous post was at 11:05 PM ----------
Natza09 said:
I have tried to flash several Roms that are 4.4 and that are compatible with my device using clock work mod and it doesn't work as i keep getting a Status 7 error which i have found a possible fix for here in the forum i will attempt to resolve and report back.
Click to expand...
Click to collapse
Ok so i put TWTP back on and i was able to install Goldeneye Rom 4.4.2, Which is working great. However when i reboot im still getting the Kernel is not seandroid enforcing message in red. As i can not restore to stock Rom as Australia XSA 4.4 isn't out yet is there any other way to get rid of this message. Thanks again.
did anyone tried this ??
Natza09 said:
Hi i have CM on my Australia XSA Samsung 19505 and i am trying to get it back to stock though when i try to flash it in Odin it fails all the time i cant get into recovery though i am able to access download mode.
I am using Odin 3.09 with the correct stock rom for my device and when i run it i get this error message
I have tried to use Kies both versions and it doesn't work, The only way to get it to work is flash CWM which allows me back into my device.
Any ideas on how to get back to stock Thanks?
Click to expand...
Click to collapse
iuts coz you are trying to downgrade the aboot file which is associated with know security check .. u have to flash the same or upgrade
franny23dmt said:
iuts coz you are trying to downgrade the aboot file which is associated with know security check .. u have to flash the same or upgrade
Click to expand...
Click to collapse
Yeah its all sorted now as version 4.4.2 has been officially released as stock on my Samsung S4, So back to "factory" now and no more message. Off to ebay it goes and Hello HTC One M8 .
Hi,
I'll Install WizCyan custom Rom on My GT-I9505 by TWRP mode. Its not a Error its a Premission That are allow when we use other roms.
●Press Volume Up and Volume Down Key at same
time and Hold it. This methode is use to Force Start your Rom
Hi, I had my S4 with stock rom 4.3 with adam kernel and philz touch recovery, tried to install via odin the stock rom 4.4.2 TTT but because of a CPU problem the usb connection was interrupted while installing. Now I'm stuck at download mode.
Here's details.
Download mode:
ODIN MODE
PRODUCT NAME: GT-I9500
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 1
RP SWREV: A3
After attempting install rom via odin:
appears the same in download mode plus this line:
SW REV. CHECK FAIL. DEVICE:-3, BINARY:2
Odin log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500UBUEMK1_I9500UUBEMK1_I9500UBUEMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've already tried the same with the PIT file but still doesn't work, anybody got a clue?
Anybody? I need my phone back :S
chemell said:
Anybody? I need my phone back :S
Click to expand...
Click to collapse
Odin was interrupted at the bootloader update (sboot.bin). You need the "factory ROM" to flash it, however I am not aware if anything for 4.2.2 would be available for now.
spamtrash said:
Odin was interrupted at the bootloader update (sboot.bin). You need the "factory ROM" to flash it, however I am not aware if anything for 4.2.2 would be available for now.
Click to expand...
Click to collapse
But can I use another rom? I don't care if isn't a 4.2.2 rom because I need the phone again doesn't matter with which rom or android version.
If u can boot to recovery flash a custom rom then flash stock via odin
aayushkhajuria2842 said:
If u can boot to recovery flash a custom rom then flash stock via odin
Click to expand...
Click to collapse
I can't, I only got download mode...
Try the right key combination .....its nt possible that you can have download mode but nt recovery
Press and hold Volume Up, Home and Power
aayushkhajuria2842 said:
Try the right key combination .....its nt possible that you can have download mode but nt recovery
Press and hold Volume Up, Home and Power
Click to expand...
Click to collapse
Well it doesn't work, when I turn on the phone a black screen with a cellphone, a warning sign and a monitor appears and a text says "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
With this screen I can only go into download mode but when I try recovery mode it just puts the screen black and back to the same text and pictures.
Another thing that worries me it's that I can't turn the phone off with the button, only if I pull the battery out.
This can be recovered I had same prblm some months ago bt I just flashed stock firmware nd it was fixed u may try flashing stock rom again
aayushkhajuria2842 said:
This can be recovered I had same prblm some months ago bt I just flashed stock firmware nd it was fixed u may try flashing stock rom again
Click to expand...
Click to collapse
I've already tried with the rom "I9500UBUEMK1_I9500UUBEMK1_I9500UBUEMK1_HOME.tar.md5" (I believe it's stock rom) and get the odin error that appears in my first post...
Try some other firmware of you own region ......... 4.3 or 4.4 whichever u have for your region .......I think then u will nt get same error
chemell said:
Hi, I had my S4 with stock rom 4.3 with adam kernel and philz touch recovery, tried to install via odin the stock rom 4.4.2 TTT but because of a CPU problem the usb connection was interrupted while installing. Now I'm stuck at download mode.
Here's details.
Download mode:
ODIN MODE
PRODUCT NAME: GT-I9500
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 1
RP SWREV: A3
After attempting install rom via odin:
appears the same in download mode plus this line:
SW REV. CHECK FAIL. DEVICE:-3, BINARY:2
Odin log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500UBUEMK1_I9500UUBEMK1_I9500UBUEMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've already tried the same with the PIT file but still doesn't work, anybody got a clue?
Click to expand...
Click to collapse
Hi, try to flash through kies emergency firmware recovery.
navdeepavi said:
Hi, try to flash through kies emergency firmware recovery.
Click to expand...
Click to collapse
Hi, I tried, but in Kies I can't get trough the "Connecting..." status so when I choose "Emergency firmware recovery" the list of devices appears empty.
I think u should try flashing some other stock firmware I hav had the prblm before
aayushkhajuria2842 said:
I think u should try flashing some other stock firmware I hav had the prblm before
Click to expand...
Click to collapse
Hi, I'm downloading another firmware now. But I don't think it will work, i've tried with a pack I found (firmware+pit+booloader+cp+csc) and didn't work. Also I tried just flashing only de BP file and keep getting the same error:
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
I don't know what to do but I'm downloading an ARO stock firmware (4.3) and I'll try...
It should work I did the same thing but cant say anything
aayushkhajuria2842 said:
I think u should try flashing some other stock firmware I hav had the prblm before
Click to expand...
Click to collapse
Obviously not. simple flash of ROM is not sorting out the corrupted bootloader problem.
---------- Post added at 07:52 AM ---------- Previous post was at 07:45 AM ----------
chemell said:
Hi, I'm downloading another firmware now. But I don't think it will work, i've tried with a pack I found (firmware+pit+booloader+cp+csc) and didn't work. Also I tried just flashing only de BP file and keep getting the same error:
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
I don't know what to do but I'm downloading an ARO stock firmware (4.3) and I'll try...
Click to expand...
Click to collapse
considering your situation, I doubt if it will work. you have to pick from two scenarios:
a) your download mode shows warranty void, knox void, custom: then you have to go to step 2 below.
b) your download mode shows all statuses samsung or official or 0x0 - then go to 1
1. Call samsung service center, they shall sort it out under the warranty.
2. More complicated, if you do not want to pay for repairs.
DELETED, procedure was for I9505 ONLY
you have to follow the procedure form this link instead.
Good luck.
spamtrash said:
Obviously not. simple flash of ROM is not sorting out the corrupted bootloader problem.
---------- Post added at 07:52 AM ---------- Previous post was at 07:45 AM ----------
considering your situation, I doubt if it will work. you have to pick from two scenarios:
a) your download mode shows warranty void, knox void, custom: then you have to go to step 2 below.
b) your download mode shows all statuses samsung or official or 0x0 - then go to 1
1. Call samsung service center, they shall sort it out under the warranty.
2. More complicated, if you do not want to pay for repairs.
You will need the PC with not faulty CPU, first.
Then, you have to use the PIT from here
Of course, you will need the Qualcomm drivers as well, from here or this one
Then, you have to follow the relatively simple procedure described here
That shall fix the corrupted bootloader, and I hope that you will not see the described there errors which would point to the hardware problem.
Good luck.
Click to expand...
Click to collapse
Warning!
He said he is in trouble with a I9500 device, so the Qualcomm drivers will not help....much.
Just an observation, you said you have no recovery right? So have you tried just flashing the tar of PhilZ recovery using Odin to get it back?
At least then you'll have a recovery again and can move forward with a custom ROM install
Sent from my GT-I9505 using XDA Premium HD app
lolo9393 said:
Warning!
He said he is in trouble with a I9500 device, so the Qualcomm drivers will not help....much.
Click to expand...
Click to collapse
right. the correct one provided.
Hi
I have AT&T Note 3 , sim unlock from carrier, successful kingo root 0x0 Knox (startup splash screen says Custom Unlock)
So, I was hopped up on percocets because of my recent surgery and i decided i was in conscious enough mind to tackle getting AWS unlock. I wasn't.
I was reading about chainfire regionaway app, so i went to the app store and downloaded the first chainfire app that popped up - 3D. so now i am stuck in the note 3 splash screen. yes i know i should have read it more carefully, etc. but i just wasn't all there at the time. Please help me save this $500 brick!
I've been reading these methods:
http://www.droidviews.com/how-to-unbrick-att-galaxy-note-3-sm-n900a/
i can get the phone recognized in ODIN, but the secure check fail: cache occurs
http://forum.xda-developers.com/showthread.php?t=2567133
i can't download any of these files...
http://forum.xda-developers.com/showthread.php?t=2507403
tried this but didn't work.
i'm really not making any headway... any help would be much appreciated.
side note:
can i send this in for warranty? Since AT&T just release the kitkat update can i claim that i tried to update and it failed?
current binary: samsung official
system status: custom (not official)
Knox lock 0x0
Knox warranty void 0x0
EDIT: After doing the ODIN fail - it is stuck in ODIN mode and says "firmware upgrade encountered an issue. Please select recory mode in Kies & try again."
Can not enter download mode. But still connects in ODIN
thanks!
Yes you can return. Best bet as Knox counter is still 0.
If you try other methods and they don't work, you may tripe Knox.
Even you connect to your pc is the phone on download mode?
kenny1991 said:
Yes you can return. Best bet as Knox counter is still 0.
If you try other methods and they don't work, you may tripe Knox.
Even you connect to your pc is the phone on download mode?
Click to expand...
Click to collapse
when i connect to PC it recognizes in ODIN but KIES does not recognize it.
It won't go into reboot mode (vol up + power + home)
it only boots into ODIN mood
firstsx said:
when i connect to PC it recognizes in ODIN but KIES does not recognize it.
It won't go into reboot mode (vol up + power + home)
it only boots into ODIN mood
Click to expand...
Click to collapse
Lol?
What are you trying to do here? Flashing anything?
Is it 4.3 or 4.4 os?
Never run kies side by side Odin add the last one hates the first. Kies is useless.
Kill it and restart your pc. Don't run kies services when using Odin.
I think you should download your firmware from sammobile.com and flash it.
Take battery out and then try download mode again. After killing kies you should be able to use Odin to flash.
---------- Post added at 10:35 PM ---------- Previous post was at 10:32 PM ----------
I don't know. But flashing kitkat may tripe Knox i don't know atnt models. If you don't want to flash then return it.
kenny1991 said:
Lol?
What are you trying to do here? Flashing anything?
Is it 4.3 or 4.4 os?
Never run kies side by side Odin add the last one hates the first. Kies is useless.
Kill it and restart your pc. Don't run kies services when using Odin.
I think you should download your firmware from sammobile.com and flash it.
Take battery out and then try download mode again. After killing kies you should be able to use Odin to flash.
Click to expand...
Click to collapse
lol sorry!
ok if i run KIES (because the screen says connect to kies and do recovery mode) it does not recognize. I am not trying to connect ODIN and kies at the same time!
it was 4.3
i download the sammobile file - it says:
SQ Rev Check fail: [sbl1]Fused 2 > Binary 1
firstsx said:
lol sorry!
ok if i run KIES (because the screen says connect to kies and do recovery mode) it does not recognize. I am not trying to connect ODIN and kies at the same time!
it was 4.3
i download the sammobile file - it says:
SQ Rev Check fail: [sbl1]Fused 2 > Binary 1
Click to expand...
Click to collapse
Where does it say? Kies? Again kies is useless. I don't think it supports note 3.
This is your firmware. http://www.sammobile.com/firmwares/3/?download=25106
You know how to flash?
kenny1991 said:
Where does it say? Kies? Again kies is useless. I don't think it supports note 3.
This is your firmware.
You know how to flash?
Click to expand...
Click to collapse
yes i know its useless, the phone itself tells me to connect to kies. I just tried it once to see if it would rexognize but it does not!
Yes i downloaded the firmware from sammobile, put it into the AP portion of ODIN and start.
but when i run it, it fails and says this on my phone
SQ Rev Check fail: [sbl1]Fused 2 > Binary 1
firstsx said:
yes i know its useless, the phone itself tells me to connect to kies. I just tried it once to see if it would rexognize but it does not!
Yes i downloaded the firmware from sammobile, put it into the AP portion of ODIN and start.
Click to expand...
Click to collapse
hm. Still no recovery mode?
Past your Odin log so someone can see why it fails.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Need pit file?
kenny1991 said:
Need pit file?
Click to expand...
Click to collapse
sammobile doesn't say anything about pit file?
i only used the AP file from there
i have HLTE__USA_ATT_32G_pit file even when i use that PIT file with the AP file it still gives me the same fail error...
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
firstsx said:
i download the sammobile file - it says:
SQ Rev Check fail: [sbl1]Fused 2 > Binary 1
Click to expand...
Click to collapse
This means you are trying to flash a version older than what is currently installed. Try the next higher revision, or find one that doesn't include a bootloader.
Sent from my leanKernel 2.3 powered stock 4.4.2 SM-N900T
toastido said:
This means you are trying to flash a version older than what is currently installed. Try the next higher revision, or find one that doesn't include a bootloader.
Sent from my leanKernel 2.3 powered stock 4.4.2 SM-N900T
Click to expand...
Click to collapse
how can there be a newer version, it was never updated to kitkat?
sammobile only lists that version and i'm quite certain it was 4.3
so if i don't flash the bootloader, what do i flash?
can i not use these files?
AP_N900AUCUBMJ5.zip
BL_N900AUCUBMJ5.zip
CP_N900AUCUBMJ5.zip
HLTE_USA_ATT_32G.pit
firstsx said:
how can there be a newer version, it was never updated to kitkat?
sammobile only lists that version and i'm quite certain it was 4.3
so if i don't flash the bootloader, what do i flash?
can i not use these files?
AP_N900AUCUBMJ5.zip
BL_N900AUCUBMJ5.zip
CP_N900AUCUBMJ5.zip
HLTE_USA_ATT_32G.pit
Click to expand...
Click to collapse
Hi mate,
if you are stuck, maybe you can try this.
http://forum.xda-developers.com/showthread.php?t=2701062
it's a way to unbrick your software.
and update to kitkat.
maybe your problem is the firmware in the sammobile were before the firmware you have install on your device via OTA update.
Yours firmware came throw out via OTA update and with some reason you can't see any latest firmware USA N900A in sammobile.
try the method in the link and reply if you have been successful.
cumps
Markudsc said:
Hi mate,
if you are stuck, maybe you can try this.
http://forum.xda-developers.com/showthread.php?t=2701062
it's a way to unbrick your software.
and update to kitkat.
maybe your problem is the firmware in the sammobile were before the firmware you have install on your device via OTA update.
Yours firmware came throw out via OTA update and with some reason you can't see any latest firmware USA N900A in sammobile.
try the method in the link and reply if you have been successful.
cumps
Click to expand...
Click to collapse
can i use this method
http://forum.xda-developers.com/showthread.php?t=2559715
it seems pretty much the same, except yours includes updating to kitkat.
if i do kitkat, can i still keep root?
will this trip knox?
Ok i did this method
http://forum.xda-developers.com/showthread.php?t=2559715
i re-downloaded all the files because the files i had just wouldn't work in ODIN or anything. so based your advice i just downloaded new files.
ODIN flash was successful
then i did the rest of the steps successfully! and i am back!