Database Users

Fixed - I9505 - kernel is not seandroid enforcing - Reboot & Hangs ! Easy !

S4 I9505
Problem:
Start up screen top left corner shows:
kernel is not seandroid enforcing
Hangs up or Reboots.
I updated my S4 to Version: I9505XXUEMKE
Then I used Odin to Flash a Root with Stock recovery & SU, something went WRONG!
Knox is now 0x1, which should not have happened, but what can I say.
BaM, I got the Reboots & Hang ups.
But, I still could get into Recovery & Download Mode!
SO HERE IS THE FIX:
1. Download, Odin 3 - THx 2 - daerragh
--- I used Ver.: Odin 3.07
2. Download, http://www.sammobile.com/firmwares/2/
--- Register
--- And download your Firmware, if you know which you had before it crashed choose that one otherwise Upgrade to latest.
--- For me it was the latest version - I9505XXUEMKE ---- THx 2 -- Repulsa for the tip.
3. Start Odin 3.07 --- [Should it "FAIL" Read note at the Bottom #6].
--- Make sure - Auto Reboot & F. Reset Time are checked - Nothing else.
--- Click on PDA choose your Firmware file in my case "I9505XXUEMKE"
--- this can take a minute or two, WAIT, the PDA will check mark itself.
4. To start Turn off your phone completely ! Now hold following buttons to get into Download Mode,
--- Volume Down
--- Home
--- and last Power
--- S4 will enter into DL Mode
Seeing you have already tried to root you phone, you should have you Samsung USB drivers.
5. Press Start
--- This will take time, after it Reboot itself,
--- remove the USB Cabel & wait
--- at least 5 minutes don't remember how long, I came back after 5 Minutes and it was done,
---------- so then if everything went well for you, have fun :good: .
6. FAIL
--- Should it Fail while uploading to your phone,
--- A. Remove Battery
--- B. Remove USB cabel
--- C. Restart.
--- Should it Fail again (which happend to me), then Do A. B. C. again.
--- and this time Touch your screen about every minute.
I Know that sounds weird, but it worked for me maybe something to do with "Stand by? no clue".
If this has help you in anyway please hit that :good: Thanks Bottun
I AM NOT RESPONSIBLE for anything happening to your phone as a result of you flashing this Rom.

[Help Please] TMO-S4- Kernel is not seandroid enforcing
Hello,
Let me start off by saying, I'm a complete newbie when it comes to rooting (Infact - It took me a few days to even convince myself to do this) and I did look around for several guilds on how to remove this error (Downloaded Odin - Got Stock TAR.MD5) But I still get this error on my phone when I start the phone, it wouldn't be much of a probelm, except it hangs for a while and then restarts.) It also gets stuck for a long time at the T-Mobile load screen. The Wifi Wont turn on their... Please Help.
Galaxy S4: SGH-M919
T-Mobile...

I'm not an expert in Android OS but I think this is not an error. It is more of a notification that the STOCK KERNEL has been change to a CUSTOM one.

eclpsues said:
I'm not an expert in Android OS but I think this is not an error. It is more of a notification that the STOCK KERNEL has been change to a CUSTOM one.
Click to expand...
Click to collapse
You are right :highfive:

Hi guys
A friend and I tried to update my rooted Samsung S4 i9505 to the official kitkat version. Had the unofficial one before. Unfortunatly we didn't turn on the usb debugging and there wasn't enough space on my memory card. After removing the data from the sd card it still didn't work (usb debuging?). My friend then tried to install a custom rom of some sort (I'm the noob here. He has some skills). No whenever I try to start my cell up the message KERNAL IS NOT SEANDROID ENFORCING pops up in the top left corner. Can I turn on the usb debugging from the pc? What should I do?
Thanks

illias9 said:
Hi guys
A friend and I tried to update my rooted Samsung S4 i9505 to the official kitkat version. Had the unofficial one before. Unfortunatly we didn't turn on the usb debugging and there wasn't enough space on my memory card. After removing the data from the sd card it still didn't work (usb debuging?). My friend then tried to install a custom rom of some sort (I'm the noob here. He has some skills). No whenever I try to start my cell up the message KERNAL IS NOT SEANDROID ENFORCING pops up in the top left corner. Can I turn on the usb debugging from the pc? What should I do?
Thanks
Click to expand...
Click to collapse
I tried to install the Gummy Rom but I got the same problem. It gets stuck in the rebooting or something. It wont pass the samsung start screen. What should I do?

Tried all of the above and no go.
Hi i have CM on my Australia XSA Samsung 19505 and i am trying to get it back to stock though when i try to flash it in Odin it fails all the time i cant get into recovery though i am able to access download mode.
I am using Odin 3.09 with the correct stock rom for my device and when i run it i get this error message
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK9_I9505XSAEMK3_I9505XXUEMK9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sbl1.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And on my device is error message
start [224,1440]
sw rev check fail fused 4 binary 3.
I also have the "kernel is not seandroid enforcing" message.
When i restart my device i get an error message "Firmware upgrade encountered an issue please select recovery mode in kies and try again"
I have tried to use Kies both versions and it doesn't work, The only way to get it to work is flash CWM which allows me back into my device.
Any ideas on how to get back to stock Thanks?

Natza09 said:
Hi i have CM on my Australia XSA Samsung 19505 and i am trying to get it back to stock though when i try to flash it in Odin it fails all the time i cant get into recovery though i am able to access download mode.
I am using Odin 3.09 with the correct stock rom for my device and when i run it i get this error message
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK9_I9505XSAEMK3_I9505XXUEMK9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sbl1.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And on my device is error message
start [224,1440]
sw rev check fail fused 4 binary 3.
I also have the "kernel is not seandroid enforcing" message.
When i restart my device i get an error message "Firmware upgrade encountered an issue please select recovery mode in kies and try again"
I have tried to use Kies both versions and it doesn't work, The only way to get it to work is flash CWM which allows me back into my device.
Any ideas on how to get back to stock Thanks?
Click to expand...
Click to collapse
Use a different usb port. Always use the ports on the back of your pc not the ones on the front.

Lennyz1988 said:
Use a different usb port. Always use the ports on the back of your pc not the ones on the front.
Click to expand...
Click to collapse
Thanks Lennyz for the reply, I tried the back usb 2.0 and 3.0 and both failed with the same error message as originally posted. Can i just restore the kernel some how and will that fix the issue?

Natza09 said:
Thanks Lennyz for the reply, I tried the back usb 2.0 and 3.0 and both failed with the same error message as originally posted. Can i just restore the kernel some how and will that fix the issue?
Click to expand...
Click to collapse
I think I know what you did. You try to flash an older stock firmware on to your device. Pick a newer firmware because downgrading is not possible.

Lennyz1988 said:
I think I know what you did. You try to flash an older stock firmware on to your device. Pick a newer firmware because downgrading is not possible.
Click to expand...
Click to collapse
I have tried to flash several Roms that are 4.4 and that are compatible with my device using clock work mod and it doesn't work as i keep getting a Status 7 error which i have found a possible fix for here in the forum i will attempt to resolve and report back.
---------- Post added at 11:40 PM ---------- Previous post was at 11:05 PM ----------
Natza09 said:
I have tried to flash several Roms that are 4.4 and that are compatible with my device using clock work mod and it doesn't work as i keep getting a Status 7 error which i have found a possible fix for here in the forum i will attempt to resolve and report back.
Click to expand...
Click to collapse
Ok so i put TWTP back on and i was able to install Goldeneye Rom 4.4.2, Which is working great. However when i reboot im still getting the Kernel is not seandroid enforcing message in red. As i can not restore to stock Rom as Australia XSA 4.4 isn't out yet is there any other way to get rid of this message. Thanks again.

did anyone tried this ??

Natza09 said:
Hi i have CM on my Australia XSA Samsung 19505 and i am trying to get it back to stock though when i try to flash it in Odin it fails all the time i cant get into recovery though i am able to access download mode.
I am using Odin 3.09 with the correct stock rom for my device and when i run it i get this error message
I have tried to use Kies both versions and it doesn't work, The only way to get it to work is flash CWM which allows me back into my device.
Any ideas on how to get back to stock Thanks?
Click to expand...
Click to collapse
iuts coz you are trying to downgrade the aboot file which is associated with know security check .. u have to flash the same or upgrade

franny23dmt said:
iuts coz you are trying to downgrade the aboot file which is associated with know security check .. u have to flash the same or upgrade
Click to expand...
Click to collapse
Yeah its all sorted now as version 4.4.2 has been officially released as stock on my Samsung S4, So back to "factory" now and no more message. Off to ebay it goes and Hello HTC One M8 .

Hi,
I'll Install WizCyan custom Rom on My GT-I9505 by TWRP mode. Its not a Error its a Premission That are allow when we use other roms.
●Press Volume Up and Volume Down Key at same
time and Hold it. This methode is use to Force Start your Rom

[Q] 4.4 Update via Odin Fail, Phone Bricked

I tried to install the 4.4.2 N9005XXUENA6_N9005OXXENA5_N9005XXUENA2 update on my Note 3 via odin 3.09.
Got an ext4 update failed error.
After this, the phone's bricked and is stuck on the Kies Recovery Screen. I tried to go into recovery mode in Kies, but it says this model does not have initialization.
I tried installing a 4.3 N9005XXUDMK3_N9005TNLDMK1_N9005XXUDMK2, but again failed. Download mode shows SW REV CHECK FAIL : [aboot] Fused 3 > Binary 2
Can someone please guide me to unbrick my phone?
I don't know what ROM I was on initially. It was the stock ROM that came with the phone.
I dont have CWM and TWRM installed.

This is not a brick at all. Just add a .pit file and restart the upgrade via Odin again.
You should be fine.

MrAndroid12 said:
This is not a brick at all. Just add a .pit file and restart the upgrade via Odin again.
You should be fine.
Click to expand...
Click to collapse
Thank you for that advice. How do I add a .pit file, and would you happen to have a link where I can download it from?

rinuvimal said:
Thank you for that advice. How do I add a .pit file, and would you happen to have a link where I can download it from?
Click to expand...
Click to collapse
search better mate http://forum.xda-developers.com/showthread.php?t=2550823

tasked28m said:
search better mate http://forum.xda-developers.com/showthread.php?t=2550823
Click to expand...
Click to collapse
I've tried all the .pit files in that thread, bro. None work. Cannot generate own pit as in phone is in recovery mode.

rinuvimal said:
I've tried all the .pit files in that thread, bro. None work. Cannot generate own pit as in phone is in recovery mode.
Click to expand...
Click to collapse
i know cfautoroot has the correct pit file in , try rooting your phone with cfautoroot.

MrAndroid12 said:
This is not a brick at all. Just add a .pit file and restart the upgrade via Odin again.
You should be fine.
Click to expand...
Click to collapse
I tried a variety of N9005 .pits and each time, it shows PIT FAIL: TOTAL SECTORS (30777344) :crying:

(Read OP) . Try flashing the polish firmware again with odin v1.85 and try using different usb ports. Close most of your running applications such as firefox skype etc that can interrupt the process and flash official firmware.

tasked28m said:
(Read OP) . Try flashing the polish firmware again with odin v1.85 and try using different usb ports. Close most of your running applications such as firefox skype etc that can interrupt the process and flash official firmware.
Click to expand...
Click to collapse
Whenever I try the 4.4.2 polish, it fails at system.img.ext4. When I try 4.3, it fails at aboot.
Here's the Odin log for 4.4.2 polish:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENA6_N9005OXXENA5_N9005XXUENA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> tz.mbn
<ID:0/006> sdi.mbn
<ID:0/006> NON-HLOS.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

bootloop note 3
After installig android 4.4.2, i tried to root with cf-root, now it is in a loop.
I cannot come into in recovery mode.
The phone starts with: -recovery booting,-recovery is not seandroid enforcing,- set warrant bit recovery
when i keep the battery out and then put it in, it says again -recovery booting,-recovery is not seandroid etc.
Who can help me????

rinuvimal said:
Whenever I try the 4.4.2 polish, it fails at system.img.ext4. When I try 4.3, it fails at aboot.
Here's the Odin log for 4.4.2 polish:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENA6_N9005OXXENA5_N9005XXUENA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> tz.mbn
<ID:0/006> sdi.mbn
<ID:0/006> NON-HLOS.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
You won't be able to downgrade back to 4.3 - Use the PDA slot on ODIN and try flashing again.
poedy said:
After installig android 4.4.2, i tried to root with cf-root, now it is in a loop.
I cannot come into in recovery mode.
The phone starts with: -recovery booting,-recovery is not seandroid enforcing,- set warrant bit recovery
when i keep the battery out and then put it in, it says again -recovery booting,-recovery is not seandroid etc.
Who can help me????
Click to expand...
Click to collapse
I answered in your other thread about this...

rinuvimal said:
I tried to install the 4.4.2 N9005XXUENA6_N9005OXXENA5_N9005XXUENA2 update on my Note 3 via odin 3.09.
Got an ext4 update failed error.
After this, the phone's bricked and is stuck on the Kies Recovery Screen. I tried to go into recovery mode in Kies, but it says this model does not have initialization.
I tried installing a 4.3 N9005XXUDMK3_N9005TNLDMK1_N9005XXUDMK2, but again failed. Download mode shows SW REV CHECK FAIL : [aboot] Fused 3 > Binary 2
Can someone please guide me to unbrick my phone?
I don't know what ROM I was on initially. It was the stock ROM that came with the phone.
I dont have CWM and TWRM installed.
Click to expand...
Click to collapse
try to downlaod and flash the 4.4.2 tar again, you cant downgrade to 4.3 as your bootlaoder got upgraded
Edit- darn am i too slow or are you too fast today @radicalisto? second time...LOL :good:

Khizar said:
try to downlaod and flash the 4.4.2 tar again, you cant downgrade to 4.3 as your bootlaoder got upgraded
Edit- darn am i too slow or are you too fast today @radicalisto? second time...LOL :good:
Click to expand...
Click to collapse
15 hour sleep man, seems to have me buzzing around lol :highfive:

Solution
I also have Hong Kong N9005 32GB with N9005XXUBMI5 PDA, tried to flash 4.4.2 with Odin and stuck at "invalid ext4 image", was't able to flash anything after it.
But after 16 hours I finally found a solution:
1. Get leaked Polish ROM (that one with 4 files, do not use the official - it has one file rom)
2. Extract archive
3. Extract "CSC_OXX_N9005OXXENA5_327209_REV03_user_low_ship_MULTI_CERT.tar" and get your pitfile - HLTE_EUR_OPEN.pit
4. Flash your phone with this pitfile and other 4 files from archive (I used Odin 3.09) with repartitioning enabled.
After this procedure I have fully working android 4.4 :victory:

m1ndst0rm said:
I also have Hong Kong N9005 32GB with N9005XXUBMI5 PDA, tried to flash 4.4.2 with Odin and stuck at "invalid ext4 image", was't able to flash anything after it.
But after 16 hours I finally found a solution:
1. Get leaked Polish ROM (that one with 4 files, do not use the official - it has one file rom)
2. Extract archive
3. Extract "CSC_OXX_N9005OXXENA5_327209_REV03_user_low_ship_MULTI_CERT.tar" and get your pitfile - HLTE_EUR_OPEN.pit
4. Flash your phone with this pitfile and other 4 files from archive (I used Odin 3.09) with repartitioning enabled.
After this procedure I have fully working android 4.4 :victory:
Click to expand...
Click to collapse
Have you tried rooting it with Chainfire's CF-Auto Root yet?

m1ndst0rm said:
I also have Hong Kong N9005 32GB with N9005XXUBMI5 PDA, tried to flash 4.4.2 with Odin and stuck at "invalid ext4 image", was't able to flash anything after it.
But after 16 hours I finally found a solution:
1. Get leaked Polish ROM (that one with 4 files, do not use the official - it has one file rom)
2. Extract archive
3. Extract "CSC_OXX_N9005OXXENA5_327209_REV03_user_low_ship_MULTI_CERT.tar" and get your pitfile - HLTE_EUR_OPEN.pit
4. Flash your phone with this pitfile and other 4 files from archive (I used Odin 3.09) with repartitioning enabled.
After this procedure I have fully working android 4.4 :victory:
Click to expand...
Click to collapse
can you show the download link for the leaked rom with 4 files?

vndnguyen said:
can you show the download link for the leaked rom with 4 files?
Click to expand...
Click to collapse
I have no permission to post links yet, but try googling for N3KitKat.rar.torrent

Leaked download link is in my sig (not this cause I am on xda app l check my other posts)
Sent from my SM-N9005 using XDA Premium 4 mobile app

ManUtdRul3 said:
Have you tried rooting it with Chainfire's CF-Auto Root yet?
Click to expand...
Click to collapse
Just tried latest one, ended up in bootloop with "KERNEL IS NOT SEANDROID ENFORCING"...
Now flashing original ROM again.

m1ndst0rm said:
Just tried latest one, ended up in bootloop with "KERNEL IS NOT SEANDROID ENFORCING"...
Now flashing original ROM again.
Click to expand...
Click to collapse
Seems to be a common problem. Hopefully an update to it will fix it.

[Q] Soft brick at&t note 3?

Hi
I have AT&T Note 3 , sim unlock from carrier, successful kingo root 0x0 Knox (startup splash screen says Custom Unlock)
So, I was hopped up on percocets because of my recent surgery and i decided i was in conscious enough mind to tackle getting AWS unlock. I wasn't.
I was reading about chainfire regionaway app, so i went to the app store and downloaded the first chainfire app that popped up - 3D. so now i am stuck in the note 3 splash screen. yes i know i should have read it more carefully, etc. but i just wasn't all there at the time. Please help me save this $500 brick!
I've been reading these methods:
http://www.droidviews.com/how-to-unbrick-att-galaxy-note-3-sm-n900a/
i can get the phone recognized in ODIN, but the secure check fail: cache occurs
http://forum.xda-developers.com/showthread.php?t=2567133
i can't download any of these files...
http://forum.xda-developers.com/showthread.php?t=2507403
tried this but didn't work.
i'm really not making any headway... any help would be much appreciated.
side note:
can i send this in for warranty? Since AT&T just release the kitkat update can i claim that i tried to update and it failed?
current binary: samsung official
system status: custom (not official)
Knox lock 0x0
Knox warranty void 0x0
EDIT: After doing the ODIN fail - it is stuck in ODIN mode and says "firmware upgrade encountered an issue. Please select recory mode in Kies & try again."
Can not enter download mode. But still connects in ODIN
thanks!

Yes you can return. Best bet as Knox counter is still 0.
If you try other methods and they don't work, you may tripe Knox.
Even you connect to your pc is the phone on download mode?

kenny1991 said:
Yes you can return. Best bet as Knox counter is still 0.
If you try other methods and they don't work, you may tripe Knox.
Even you connect to your pc is the phone on download mode?
Click to expand...
Click to collapse
when i connect to PC it recognizes in ODIN but KIES does not recognize it.
It won't go into reboot mode (vol up + power + home)
it only boots into ODIN mood

firstsx said:
when i connect to PC it recognizes in ODIN but KIES does not recognize it.
It won't go into reboot mode (vol up + power + home)
it only boots into ODIN mood
Click to expand...
Click to collapse
Lol?
What are you trying to do here? Flashing anything?
Is it 4.3 or 4.4 os?
Never run kies side by side Odin add the last one hates the first. Kies is useless.
Kill it and restart your pc. Don't run kies services when using Odin.
I think you should download your firmware from sammobile.com and flash it.
Take battery out and then try download mode again. After killing kies you should be able to use Odin to flash.
---------- Post added at 10:35 PM ---------- Previous post was at 10:32 PM ----------
I don't know. But flashing kitkat may tripe Knox i don't know atnt models. If you don't want to flash then return it.

kenny1991 said:
Lol?
What are you trying to do here? Flashing anything?
Is it 4.3 or 4.4 os?
Never run kies side by side Odin add the last one hates the first. Kies is useless.
Kill it and restart your pc. Don't run kies services when using Odin.
I think you should download your firmware from sammobile.com and flash it.
Take battery out and then try download mode again. After killing kies you should be able to use Odin to flash.
Click to expand...
Click to collapse
lol sorry!
ok if i run KIES (because the screen says connect to kies and do recovery mode) it does not recognize. I am not trying to connect ODIN and kies at the same time!
it was 4.3
i download the sammobile file - it says:
SQ Rev Check fail: [sbl1]Fused 2 > Binary 1

firstsx said:
lol sorry!
ok if i run KIES (because the screen says connect to kies and do recovery mode) it does not recognize. I am not trying to connect ODIN and kies at the same time!
it was 4.3
i download the sammobile file - it says:
SQ Rev Check fail: [sbl1]Fused 2 > Binary 1
Click to expand...
Click to collapse
Where does it say? Kies? Again kies is useless. I don't think it supports note 3.
This is your firmware. http://www.sammobile.com/firmwares/3/?download=25106
You know how to flash?

kenny1991 said:
Where does it say? Kies? Again kies is useless. I don't think it supports note 3.
This is your firmware.
You know how to flash?
Click to expand...
Click to collapse
yes i know its useless, the phone itself tells me to connect to kies. I just tried it once to see if it would rexognize but it does not!
Yes i downloaded the firmware from sammobile, put it into the AP portion of ODIN and start.
but when i run it, it fails and says this on my phone
SQ Rev Check fail: [sbl1]Fused 2 > Binary 1

firstsx said:
yes i know its useless, the phone itself tells me to connect to kies. I just tried it once to see if it would rexognize but it does not!
Yes i downloaded the firmware from sammobile, put it into the AP portion of ODIN and start.
Click to expand...
Click to collapse
hm. Still no recovery mode?
Past your Odin log so someone can see why it fails.

<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Need pit file?

kenny1991 said:
Need pit file?
Click to expand...
Click to collapse
sammobile doesn't say anything about pit file?
i only used the AP file from there
i have HLTE__USA_ATT_32G_pit file even when i use that PIT file with the AP file it still gives me the same fail error...
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

firstsx said:
i download the sammobile file - it says:
SQ Rev Check fail: [sbl1]Fused 2 > Binary 1
Click to expand...
Click to collapse
This means you are trying to flash a version older than what is currently installed. Try the next higher revision, or find one that doesn't include a bootloader.
Sent from my leanKernel 2.3 powered stock 4.4.2 SM-N900T

toastido said:
This means you are trying to flash a version older than what is currently installed. Try the next higher revision, or find one that doesn't include a bootloader.
Sent from my leanKernel 2.3 powered stock 4.4.2 SM-N900T
Click to expand...
Click to collapse
how can there be a newer version, it was never updated to kitkat?
sammobile only lists that version and i'm quite certain it was 4.3
so if i don't flash the bootloader, what do i flash?
can i not use these files?
AP_N900AUCUBMJ5.zip
BL_N900AUCUBMJ5.zip
CP_N900AUCUBMJ5.zip
HLTE_USA_ATT_32G.pit

firstsx said:
how can there be a newer version, it was never updated to kitkat?
sammobile only lists that version and i'm quite certain it was 4.3
so if i don't flash the bootloader, what do i flash?
can i not use these files?
AP_N900AUCUBMJ5.zip
BL_N900AUCUBMJ5.zip
CP_N900AUCUBMJ5.zip
HLTE_USA_ATT_32G.pit
Click to expand...
Click to collapse
Hi mate,
if you are stuck, maybe you can try this.
http://forum.xda-developers.com/showthread.php?t=2701062
it's a way to unbrick your software.
and update to kitkat.
maybe your problem is the firmware in the sammobile were before the firmware you have install on your device via OTA update.
Yours firmware came throw out via OTA update and with some reason you can't see any latest firmware USA N900A in sammobile.
try the method in the link and reply if you have been successful.
cumps

Markudsc said:
Hi mate,
if you are stuck, maybe you can try this.
http://forum.xda-developers.com/showthread.php?t=2701062
it's a way to unbrick your software.
and update to kitkat.
maybe your problem is the firmware in the sammobile were before the firmware you have install on your device via OTA update.
Yours firmware came throw out via OTA update and with some reason you can't see any latest firmware USA N900A in sammobile.
try the method in the link and reply if you have been successful.
cumps
Click to expand...
Click to collapse
can i use this method
http://forum.xda-developers.com/showthread.php?t=2559715
it seems pretty much the same, except yours includes updating to kitkat.
if i do kitkat, can i still keep root?
will this trip knox?

Ok i did this method
http://forum.xda-developers.com/showthread.php?t=2559715
i re-downloaded all the files because the files i had just wouldn't work in ODIN or anything. so based your advice i just downloaded new files.
ODIN flash was successful
then i did the rest of the steps successfully! and i am back!

[SOLVED] My first soft? brick after 15Y of membership. PLEASE HELP

Hi,
I managed to be brick free since I started reading XDA Developers & modifying my devices starting with my XDA Mini in 2008. Now 6 devices later I finally managed to - hopefully just soft - brick my Note 3 (hlte)
I bet if I search long enough I could try to recover it on my own, and i did so the lasst 15 years, but I am a bit scared now, I really fear to loose the last thread this phone is hanging on, so please hear me out and maybe its an easy problem for the more expiereinced users out there.
Situation before the update:
* rooted
* cwm recovery - latest version
* cm11 latest snapshot
* Encryption enabled
The update:
- Used adb sideload method to load cm12.1 latest nightly
- Phone booted fine, just was completely misconfigured (Xposed not working, root apps lost root access, etc.)
- Wanted to go to recovery, but recovery stopped working. Phone just showed shortly it goes to recovery, then black screen
- So I factory resetted the phone via normal CM settings.
- Everything was fine, I started to install apps and was happy.
- Phone is currenlty NOT encrypted anymore
- I totally forgot to fix the not working recovery mode *DOUH*
- Then I changed the DPI settings in build.prop to 320 as it was under cm11
- Phone never rebooted.
The situation now:
- Phone does not boot normally, shows black screen right after boot mode details in top left corner. No boot logo and such
- Phone can't enter recovery, same as with normal boot
- ADB can not see the device in either normal boot/recovery/download mode
- Download mode seems to be still working *HOPE*
So what to do now?
Can I somehow just fix the build.props?
Can I flash a new recovery using ODIN, and then format/wipe/reinstall?
Can I simply reflash CM12.1 using ODIN?
Or do I have to, as some howto suggested, flash a stock samsung rom? And which one for that matter?
Hope someone can help me,
CySlider
Update: Solved by pushing the right stock rom to the device using ODIN.
Interesting part I learned: You can flash multiple times with ODIN without rebooting the device if flashing fails. You just have to unplug and replug the cable (quickly if Battery is nearly dead). Messages on Screen might get messy with errors that the loading bar got wrong values, but it works.

Flash stock Samsung rom via Odin .
Can I somehow just fix the build.props? YES if you can see it on your phone.

JJEgan said:
Flash stock Samsung rom via Odin .
Can I somehow just fix the build.props? YES if you can see it on your phone.
Click to expand...
Click to collapse
Ok, which one, Lolipop? or Kitkat? Last stock that was installed before going to Cyanogenmod was Kitkat or even older.
Also will I loose root access this way?

Cy_the_Slider said:
Ok, which one, Lolipop? or Kitkat? Last stock that was installed before going to Cyanogenmod was Kitkat or even older.
Also will I loose root access this way?
Click to expand...
Click to collapse
If you just want a cm rom just flash a kit kat official rom.
Anyway try to go into download mode. When it asks to cancel or continue choose cancel. I saw several members mentioned the phone managed to boot that way.
And off course no root.
Sent from my SM-N920C

Rosli59564 said:
If you just want a cm rom just flash a kit kat official rom.
Anyway try to go into download mode. When it asks to cancel or continue choose cancel. I saw several members mentioned the phone managed to boot that way.
And off course no root.
Sent from my SM-N920C
Click to expand...
Click to collapse
Ok, thank you. About the tip with Cancel. unfortunately it did not help. I geuss the problem is an invalid DPI setting in the build.props and it will not changed by going to download mode first :/
Ok I will try to locate a stock rom with Kitkat.
Thank you.

No success it seams:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:1/012> Added!!
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:1/012> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:1/012> File analysis..
<ID:0/007> SetupConnection..
<ID:1/012> SetupConnection..
<ID:1/012> Initialzation..
<ID:1/012> Get PIT for mapping..
<ID:1/012> Firmware update start..
<ID:1/012> SingleDownload.
<ID:1/012> sbl1.mbn
<ID:1/012> NAND Write Start!!
<ID:1/012> aboot.mbn
<ID:1/012> rpm.mbn
<ID:1/012> tz.mbn
<ID:1/012> sdi.mbn
<ID:1/012> NON-HLOS.bin
<ID:1/012> boot.img
<ID:1/012> recovery.img
<ID:1/012> system.img.ext4
<ID:0/007> Can't open the serial(COM) port.
<ID:1/012> modem.bin
<ID:1/012> cache.img.ext4
<ID:1/012> hidden.img.ext4
<ID:1/012> FAIL! (Size)
<ID:1/012>
<ID:1/012> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 2)
I used: N9005XXUGNG1_N9005DBTGNG1_N9005XXUGNG1_HOME.tar.md5 and set it to AP setting in ODIN 3.10.7
CAN I leave Download mode to test, if something changed? Or should I better stay in download mode to try again?

Ok, after realizing that I can not flash again without reentering the doanload mode anyway, I restarted.
It showed a new download mode with the message:
"Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I searched and found that I should use the right PIT file. I found a combination that seemed to match my device here: (german)
http://www.pocketpc.ch/samsung-gala...1800-anleitung-flashen-dbt-fw-eu-geraete.html
I did hold my breath, and...: Failed again:
<ID:0/012> Added!!
<ID:0/012> Removed!!
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUGBOE9_N9005DBTGBOF1_N9005XXUGBOD3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Set PIT file..
<ID:0/012> DO NOT TURN OFF TARGET!!
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> SingleDownload.
<ID:0/012> aboot.mbn
<ID:0/012> NAND Write Start!!
<ID:0/012> boot.img
<ID:0/012> cache.img.ext4
<ID:0/012> hidden.img.ext4
<ID:0/012> FAIL! (Size)
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
So, did I finally manage to hard brick? ((
I'm still in this special mode scraed frozen about powering off as I saw messages saying this is the last shot I had. COME ON!!

What I don't get is. After updating to CM12.1 didn't I got Lolipop bootloader with it? Maybe trying to put on 4.4.2 was wrong after all, b/c of downgrade?
Rop left in download mode is this info:
Product Name: SM-N9005
Current Binary: Custom
System Status: Custom
Reactivation Lock(KK): Off
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S2, T2, R2, A3, P2
WRITE PROTECTION: Enabled
UDC START
anyone?

Cy_the_Slider said:
What I don't get is. After updating to CM12.1 didn't I got Lolipop bootloader with it? Maybe trying to put on 4.4.2 was wrong after all, b/c of downgrade?
Rop left in download mode is this info:
Product Name: SM-N9005
Current Binary: Custom
System Status: Custom
Reactivation Lock(KK): Off
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S2, T2, R2, A3, P2
WRITE PROTECTION: Enabled
UDC START
anyone?
Click to expand...
Click to collapse
Try non DBT firmware. So you can still enter download mod?.
Sent from my SM-N920C

Rosli59564 said:
Try non DBT firmware. So you can still enter download mod?.
Click to expand...
Click to collapse
I don't know. Luckily, if I unplug and replug the USB Cable quickly, I seem to be able to flash again without the need to find out, if it will boot again.
I am currently downloading the UK version as I think to remember it was an english phone. (Got it as a present)
I just don't understand why the PIT did not fix this issue. it should have resizeed the partition anyway...
Damn I feel stressed...

Cy_the_Slider said:
I don't know. Luckily, if I unplug and replug the USB Cable quickly, I seem to be able to flash again without the need to find out, if it will boot again.
I am currently downloading the UK version as I think to remember it was an english phone. (Got it as a present)
I just don't understand why the PIT did not fix this issue. it should have resizeed the partition anyway...
Damn I feel stressed...
Click to expand...
Click to collapse
Can't you just flash a twrp and flash a CM from there?
Sent from my SM-N920C

If you tell me how to flash a twrp via odin. Sure I would try. Is this possible?
The UK Rom download finished. Lets see if htis works.

Ok, Flashing the UK BTU rom worked in the sense that ODIN did not show any errors.
When I try to start it, it starts until it asks for a password?!? then it crashes.
I can enter recovery, but when I factory reset, it does not start at all and recovery is also gone again. Only Downloadmode is luckily still available.
Have I messed up the factory reset feature by applying the PIT file for the german rom maybe?
Update: Seems I made it. The last problem now was the Batery being completely dead as it seems to not be loading while in this broken state. And the USB PC connection was not delivering enough power to survive the phone fully booting. Now its on the loginscreen and charging.
Hopefully I can put a Solved behind this topic soon. Thanks for all input!

I9505 Softbricked, Cannot be flashed with odin :(

Hello,
I have problems with my s4 I9505 while I try to unbrick it
After a ota update from android 4.4.2 to 5.X (Orginal Firmware from Samsung) it cannot boot and enter Recovery and now I try to flash Firmware with odin but my phone turning screen off during odin says System.img.ext4 but the phone seens still working because it is showing in odin as connected but it doesn't continue flashing
I also see a new stuff in Download Mode Like Write Protection Enabled and eMMC Burst Mode Enabled

MichalPlays said:
Hello,
I have problems with my s4 I9505 while I try to unbrick it
After a ota update from android 4.4.2 to 5.X (Orginal Firmware from Samsung) it cannot boot and enter Recovery and now I try to flash Firmware with odin but my phone turning screen off during odin says System.img.ext4 but the phone seens still working because it is showing in odin as connected but it doesn't continue flashing
I also see a new stuff in Download Mode Like Write Protection Enabled and eMMC Burst Mode Enabled
Click to expand...
Click to collapse
Which firmware were you trying to flash through Odin? Is it KK or Lollipop?

Post the Odin log here.

Mandark52 said:
Which firmware were you trying to flash through Odin? Is it KK or Lollipop?
Click to expand...
Click to collapse
I tryed to flash Lollipop 5.0.1 (Orginal Firmware) and before brick I had Cyanogenmod Lollipop with Old Samsung Lollipop Modem and all worked fine until this **** ota update :/

Lennyz1988 said:
Post the Odin log here.
Click to expand...
Click to collapse
Ok, I will post it at 4:30p.m. (German Time Zone)

Lennyz1988 said:
Post the Odin log here.
Click to expand...
Click to collapse
ODIN LOG:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUHOJ2_I9505OXAHOJ2_I9505XXUHOJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> tz.mbn
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img.ext4
(Device Freeze,after 2h battery empty)
<ID:0/007> Removed!!
<OSM> All threads completed. (succeed 0 / failed 1)

MichalPlays said:
ODIN LOG:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUHOJ2_I9505OXAHOJ2_I9505XXUHOJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> tz.mbn
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img.ext4
(Device Freeze,after 2h battery empty)
<ID:0/007> Removed!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Use a different usb port/different usb cable. That will solve it.

Lennyz1988 said:
Use a different usb port/different usb cable. That will solve it.
Click to expand...
Click to collapse
Nope I tryed now this already :/
I tested also the battery with my other s4 and it worked fine.
There is a pict. that showing where I put the firmware file and what option I select
hmm, what is this CSC and Phone slots at odin?
sry 4 my bad english

Maybe try a newer version of Odin?

MichalPlays said:
Nope I tryed now this already :/
I tested also the battery with my other s4 and it worked fine.
There is a pict. that showing where I put the firmware file and what option I select
hmm, what is this CSC and Phone slots at odin?
sry 4 my bad english
Click to expand...
Click to collapse
Then try a different pc. the log doesn't show anything strange that would let me doubt my suggestion.

Lennyz1988 said:
Then try a different pc. the log doesn't show anything strange that would let me doubt my suggestion.
Click to expand...
Click to collapse
At all my pc's one with win7 and another with windows xp - sp3 it are the same, maybe I need to flash something other and them the firmware :/

@MichalPlays Try using Odin 307.

downgrade Samsung s4 [GT-I9505] from Lolipop 5.0.1 to kitkat 4.4.2
Please read the entire post and don’t skip any steps, note that we cannot be blamed in case something goes wrong and you brick the phone.
1)-Make sure that your phone version is GT-I9505 (if you don't know how to check ; remove your battery then you will find)
2)-Download[/B] " SAMSUNG USB Driver for Mobile Phones" and setup, if you dont have it already
-Download Odin3-v3.09
-Download "PDA" ; "[email protected]" [1.52 GB]
-Download "BL" ; "Bootloader_GNK2.tar" [2.12 MB]
-Download "CP"; "Modem_GNK2_FULL.tar" [61.46 MB]
3)- your phone must be Charged 70% or more, and Rooted, if you have Samsung Kies; reboot your pc then end Kies from CPU (Ctrl + Alt + Supp).
4)-extract Odin and Start a program as an administrator then put only the PDA file which you've already downloaded and extracted before "([email protected])"
-Disable « Auto Reboot » and « Re-Partition »
-Enable « F. Reset Time » only
-Reboot your phone on Download Mode ( Power off the Phone completely, Press and hold Volume Down, Home and Power buttons, all at the same time.
Release the buttons only when the ‘Warning!!’ message appears.
Next, press Volume Up button to confirm that you wish to enter Download Mode.
Your device will now show a green Android with the ‘Downloading… Do not turn off target’ text listed under it.).
-Connect your device with your PC and check "Added Message" and « ID:COM » in Odin
-Start
5)-Once you have "PASS" Plug out your Phone, and Reboot again in "Download Mode",
-Reset Odin
-Enable « Auto Reboot »and « F. Reset Time » only
-Put « Bootloader_GNK2.tar » on "BL"
-Put « Modem_GNK2_FULL.tar » on "CP
-Plug in your Phone and check "Added Message" and « ID:COM » if it doesn't work; restart Odin.
-Start to Downgrade
6)-Once the Downgrade done, plug out your phone and Hard Reset ;
(Power off your phone completely. Boot it in Recovery Mode. Select the ‘wipe data/ factory reset’ option. Confirm process by selecting the ‘Yes — delete all user data’ option. Press Power to confirm process. Reboot the phone when the Hard Reset/ Factory Reset is completed).
7)-Enjoy...

MichalPlays said:
At all my pc's one with win7 and another with windows xp - sp3 it are the same, maybe I need to flash something other and them the firmware :/
Click to expand...
Click to collapse
Ok then we can probably rule that out.
Are you using the original cable? Did you try different cables?

Lennyz1988 said:
Ok then we can probably rule that out.
Are you using the original cable? Did you try different cables?
Click to expand...
Click to collapse
I use always Original Cable and tested with cable from s4, s3, s3neo and htc one x plus and all doesn't work I tryed now the tutorial from this one guy this all was the same :/
btw. can I flash and enter a costum recovery without android on it ??

MichalPlays said:
I use always Original Cable and tested with cable from s4, s3, s3neo and htc one x plus and all doesn't work I tryed now the tutorial from this one guy this all was the same :/
btw. can I flash and enter a costum recovery without android on it ??
Click to expand...
Click to collapse
Yeah you can do that. Flash the latest TWRP. Uncheck auto-reboot before flashing with Odin.

Lennyz1988 said:
Yeah you can do that. Flash the latest TWRP. Uncheck auto-reboot before flashing with Odin.
Click to expand...
Click to collapse
oh, ok I will try this becasue I have this cyanogenmod .rar file on sd card and have also there an nandroid backup