Database Users

PLEASE HELP - Phone soft bricked after ICS LPY

Hi All,
So, I was one of those people who last night decided I needed to have clean install for my newly LPY ICS flashed through odin PC. Obviously, I had not read the warning threads only after my phone got stuck on format and then rebooted and got stuck on logo did I visit XDA and saw the new warning Anyhow, what I had flashed was a rooted version of LPY ICS. Now, I have access to download mode but when I tried to reflash through Odin PC I get a failed attempt with this message !!!
**Edit: I don't think I did use repartition...I usually never do....this all started after me trying to clean install via CWM from official rooted LPY it got stuck on formatting then rebooted and was on logo forever so I proceeded to use Odin flashing LPY failed, tried all methods posted here besides flashing kernel Abyuss note 4.2 from in PDA as someone here suggested but since I can't find one that works with Odin I just reflash LC1 rooted stock multiple times but no luck it fails and NAND Write Start which is almost at the end of flashing.
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
MODEM_N7000XXLB2_REV_05_CL1106002.tar.md5 is valid.
Rooted_Stock_Odex_N7000XXLC1.tar.md5 is valid.
GT-N7000-MULTI-CSC-OXALC1.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:13)..
File analysis..
SetupConnection..
Initialzation..
Set PIT file..
DO NOT TURN OFF TARGET!!
Can't open the specified file. (Line: 1876)
All threads completed. (succeed 0 / failed 1)
Can anyone please help. I have no idea what I should do I even tried flashing stock ICS LPY but at 3/4 of the way it would also fail!!!

jwais said:
Hi All,
So, I was one of those people who last night decided I needed to have clean install for my newly LPY ICS flashed through odin PC. Obviously, I had not read the warning threads only after my phone got stuck on format and then rebooted and got stuck on logo did I visit XDA and saw the new warning Anyhow, what I had flashed was a rooted version of LPY ICS. Now, I have access to download mode but when I tried to reflash through Odin PC I get a failed attempt with this message !!!
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_N7000XXLB2_REV_05_CL1106002.tar.md5 is valid.
<OSM> Rooted_Stock_Odex_N7000XXLC1.tar.md5 is valid.
<OSM> GT-N7000-MULTI-CSC-OXALC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Set PIT file..
<ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013> Can't open the specified file. (Line: 1876)
<OSM> All threads completed. (succeed 0 / failed 1)
Can anyone please help. I have no idea what I should do I even tried flashing stock ICS LPY but at 3/4 of the way it would also fail!!!
Click to expand...
Click to collapse
Did you backup your previous from ..if you did just go into recovery and restore it
Sent from my GT-N7000 using xda premium

You are making one huge mistake : you have the box "re-partition" selected. Uncheck that option and you should be good to go.
P_

jwais said:
Hi All,
So, I was one of those people who last night decided I needed to have clean install for my newly LPY ICS flashed through odin PC. Obviously, I had not read the warning threads only after my phone got stuck on format and then rebooted and got stuck on logo did I visit XDA and saw the new warning Anyhow, what I had flashed was a rooted version of LPY ICS. Now, I have access to download mode but when I tried to reflash through Odin PC I get a failed attempt with this message !!!
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_N7000XXLB2_REV_05_CL1106002.tar.md5 is valid.
<OSM> Rooted_Stock_Odex_N7000XXLC1.tar.md5 is valid.
<OSM> GT-N7000-MULTI-CSC-OXALC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Set PIT file..
<ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013> Can't open the specified file. (Line: 1876)
<OSM> All threads completed. (succeed 0 / failed 1)
Can anyone please help. I have no idea what I should do I even tried flashing stock ICS LPY but at 3/4 of the way it would also fail!!!
Click to expand...
Click to collapse
Try to flash gingerbread rom from http://forum.xda-developers.com/showthread.php?t=1535025 i would try this one "N7000XXLC1_N7000OXALC1 Open Europe (02/03/2012)" because it a full wipe.

Here is how to solve.
1.flash stck GB rom
2.wipe data/cache from stock recovery.
3.now flash stock ics.
4.then flash another rom/ root kernel
Sent from my GT-N7000 using xda premium

awesome-member said:
Here is how to solve.
1.flash stck GB rom
2.wipe data/cache from stock recovery.
3.now flash stock ics.
4.then flash another rom/ root kernel
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
That' the safest way.
Sent from my Galaxy Note

Thanks guys, I tried reflashing stock GB lc1 and it stoped on odin pc sayig failed and I did not repartition this time. Tried reflashing stock ICS LPY with no luck...it fails.
If anyone has another option please let me know...I cannot access recovery only download mode when I try to access recovery it gives me " firmware upgrade failed encountered an issue. Please select recovery mode in kies & try gain" .....

jwais said:
Thanks guys, I tried reflashing stock GB lc1 and it stoped on odin pc sayig failed and I did not repartition this time. Tried reflashing stock ICS LPY with no luck...it fails.
If anyone has another option please let me know...I cannot access recovery only download mode.....
Click to expand...
Click to collapse
Try to find the pit file and use it with repartition checked.
Sent from my GT-N7000 using XDA

just to be sure,
did u kill all kies processes?

aww
jwais said:
Hi All,
So, I was one of those people who last night decided I needed to have clean install for my newly LPY ICS flashed through odin PC. Obviously, I had not read the warning threads only after my phone got stuck on format and then rebooted and got stuck on logo did I visit XDA and saw the new warning Anyhow, what I had flashed was a rooted version of LPY ICS. Now, I have access to download mode but when I tried to reflash through Odin PC I get a failed attempt with this message !!!
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_N7000XXLB2_REV_05_CL1106002.tar.md5 is valid.
<OSM> Rooted_Stock_Odex_N7000XXLC1.tar.md5 is valid.
<OSM> GT-N7000-MULTI-CSC-OXALC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Set PIT file..
<ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013> Can't open the specified file. (Line: 1876)
<OSM> All threads completed. (succeed 0 / failed 1)
Can anyone please help. I have no idea what I should do I even tried flashing stock ICS LPY but at 3/4 of the way it would also fail!!!
Click to expand...
Click to collapse
idk how to i wish i could man

Kill KiesHelper.exe and KiesPDLR.exe and try to flash again

Yup killed all kies processes. Reflashing stock LC1 one last time with odin pc as suggested....pray for me

I had this similar issue. I had to completely un install Kies and then Odin worked without issue
Sent from my GT-N7000 using xda premium

i slashed my knees open, knelt with salt and lemon on the ground. i can't do this for long.... is your note ok (i hope i do not have to do some other kind of rituals for the flash procedure to work for you).

Ok guys after trying to reflash second time stock GB LC1 with odin pc this is what I get:
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Rooted_Stock_Odex_N7000XXLC1.tar.md5 is valid.
<OSM> MODEM_N7000XXLB2_REV_05_CL1106002.tar.md5 is valid.
<OSM> GT-N7000-MULTI-CSC-OXALC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013> Firmware update start..
<ID:0/013> factoryfs.img
<ID:0/013> NAND Write Start!!
<ID:0/013>
<ID:0/013> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/013> Removed!!
It goes almost all the way but then somehow stops at the nand write part. Anyone has any clue?

Did you completely uninstall kies? It's worth a shot...
Sent from my GT-N7000 using xda premium

Uninstalling Kies right now...will try again flashing. Thanks!

take out your battery, restart the pc... and try another cable if possible.
make sure all firewalls and/or antivirus softwares are disabled. if it helps, run odin as administrator.
while you do that, i shall make a bonfire and prepare to dance around naked around the flame and chant the songs my great ancestors has been singing since time immemorial.

Ok, I think I found a pattern for the failed attempts during flashing...it always stalls and fails during the NAND Write Start.....anyone has any clue as to why?

Maybe it sounds stupid but what version of Odin do yo use?

[Q] Need PIT file for Galaxy S4 I9505

Hi Everyone
I've bricked my S4 stupidly by trying to install CF Auto Root without having USB Debugging enabled.
No my phone starts up telling me there was an incomplete upgrade and to continue it but kies can't seem to find anything.
I've tried reflashing the stock firmware but I keep receiving a error saying it can't find the PIT file for mapping.
Does anyone have one for the S4 I9505 INTL (UK) Variant.
Thanks

sandeepsb said:
Hi Everyone
I've bricked my S4 stupidly by trying to install CF Auto Root without having USB Debugging enabled.
No my phone starts up telling me there was an incomplete upgrade and to continue it but kies can't seem to find anything.
I've tried reflashing the stock firmware but I keep receiving a error saying it can't find the PIT file for mapping.
Does anyone have one for the S4 I9505 INTL (UK) Variant.
Thanks
Click to expand...
Click to collapse
usb debugging
see my signature for flashing with pit :good:

samersh72 said:
usb debugging
see my signature for flashing with pit :good:
Click to expand...
Click to collapse
I've just downloaded your pit file. The problem here is I can't get back into my phone and I can only go into download mode. Initially I set USB Debugging as off and tried flashing. So now I'm stuck with a bricked phone.

sandeepsb said:
I've just downloaded your pit file. The problem here is I can't get back into my phone and I can only go into download mode. Initially I set USB Debugging as off and tried flashing. So now I'm stuck with a bricked phone.
Click to expand...
Click to collapse
NO need to enable usb debugging to flash with odin, just put pit file and the firmware in odin and flash

sandeepsb said:
I've just downloaded your pit file. The problem here is I can't get back into my phone and I can only go into download mode. Initially I set USB Debugging as off and tried flashing. So now I'm stuck with a bricked phone.
Click to expand...
Click to collapse
Do not start panicking so soon all this happens while we tinker with device follow what samersh72 saying u ll have ur device working
Its not bricked at all
Sent from my GT-I9500 using xda premium

samersh72 said:
usb debugging
see my signature for flashing with pit :good:
Click to expand...
Click to collapse
samersh72 said:
NO need to enable usb debugging to flash with odin, just put pit file and the firmware in odin and flash
Click to expand...
Click to collapse
I've tried it and I'm getting a Failed message:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
I've attached a screenshot.

sandeepsb said:
I've tried it and I'm getting a Failed message:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
I've attached a screenshot.
Click to expand...
Click to collapse
Just tried again and I'm receiving this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

sandeepsb said:
Just tried again and I'm receiving this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try using ODIN 3.07 version
also make sure u have no kies programme running , try using diff usb port
it should work

sandeepsb said:
I've tried it and I'm getting a Failed message:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDM_I9505OXXAMDB_I9505XXUAMDM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
I've attached a screenshot.
Click to expand...
Click to collapse
remove pit file from folder and put it on desktop and the firmware and odin
use odin 3.07 or 1.85
change usb port and use original cable
if you can go in recovery (i doubt)make a wipe)
retry

samersh72 said:
remove pit file from folder and put it on desktop and the firmware and odin
use odin 3.07 or 1.85
change usb port and use original cable
if you can go in recovery (i doubt)make a wipe)
retry
Click to expand...
Click to collapse
Crisis averted just flashed the PIT without anything in the PDA section and I've managed to boot back into my phone.
Thanks for the help and the PIT file.

sandeepsb said:
Crisis averted just flashed the PIT without anything in the PDA section and I've managed to boot back into my phone.
Thanks for the help and the PIT file.
Click to expand...
Click to collapse
glad to hear that, but usually it is flashed with the firmware if you would try again you will succeed......any way you make it :good:

Same happened with me, no matter how many times I tried flashing the PIT with the firmware, it just wouldn't have it at all.
When I flashed the PIT on it's own, it flashed fine, said reset, then booted back into android.
Glad you got it sorted though! It's scary when you see FAIL in big letters when flashing stuff! haha.

Read more, Learn more.....
---------- Post added at 07:45 PM ---------- Previous post was at 07:35 PM ----------
but in some cases where there is a serious firmware issue, pit file will work only with flashing firmware

Please help, I need the PIT file for M919 (T-mobile), anyone have it? Pleaseeeeee.

T-Mo GS4 Pit File
xs2k said:
Please help, I need the PIT file for M919 (T-mobile), anyone have it? Pleaseeeeee.
Click to expand...
Click to collapse
I too Also need this file as well, I can only seem to find the international GS4 pit files.

samersh72 said:
NO need to enable usb debugging to flash with odin, just put pit file and the firmware in odin and flash
Click to expand...
Click to collapse
samersh72 said:
remove pit file from folder and put it on desktop and the firmware and odin
use odin 3.07 or 1.85
change usb port and use original cable
if you can go in recovery (i doubt)make a wipe)
retry
Click to expand...
Click to collapse
I cant find the PIT partition file anywhere on your sig
I dunno if im looking in the wrong place. Can you give me a hint on where it is?
Im having problems with my phone and it wont load past the boot animation.
Chris

scientificharmony said:
I cant find the PIT partition file anywhere on your sig
I dunno if im looking in the wrong place. Can you give me a hint on where it is?
Im having problems with my phone and it wont load past the boot animation.
Chris
Click to expand...
Click to collapse
Attached here in first post http://forum.xda-developers.com/showthread.php?t=2265477
Sent from my Galaxy

samersh72 said:
Attached here in first post http://forum.xda-developers.com/showthread.php?t=2265477
Sent from my Galaxy
Click to expand...
Click to collapse
Hi, Thanks for that info. The device has now boot, but i seem to have error messages in recovery cannot mount E:\ etc etc
how the hell do i fix that lol

scientificharmony said:
Hi, Thanks for that info. The device has now boot, but i seem to have error messages in recovery cannot mount E:\ etc etc
how the hell do i fix that lol
Click to expand...
Click to collapse
reflash with i9505-cwm-recovery-6.0.3.2-4
wipe all
reflash with pit CSB_signed_Fusion3_EUR_0325_V2 and pda I9505XXUAME2_I9505OLBAMDM_I9505DXUAME2_HOME.tar

Just a word from me guys.
Please don't underestimate power of changing USB port and/or USB cable. I've just been sitting on soft-bricked s4, nothing seemed to work, ODIN 3.x or 1.8, original firmware or third party ROM/recovery etc, PIT file, nothing could be overwritten. I restarted PC and instal/reinstall drivers.. nothing.
I've changed the cable and USB port to the rear one et voila, all worked as a charm.
good luck.

HELP PLEASE!!! firmware error

OK so this is what i did. so i tried to root my s4, and in odin it said fail. so i took out the battery. and try to turn it on now it has the phone YELLOW triangle and a monitor. it says "firumware upgrade encountered an issue. Please select recovery mod in kies & try again.
what i have tried so far was download the sprint stock and odin it back. i used qbking77 . com the stock i used is linked on that website. which then links me to stockroms.net. so during the process of doing going back to stock it said fail. i read some where that in the id:com on odin, it should say 0:[COM6] and i read some where else that it does have to say com6 it could say com3. i dont know if that matters. and i also read on the forum they say to use another stock rom? is that also if so where can i get one besides from stockroms.net please someone help me..
this is what it says when i try to odin to stock:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!

Sounds like a bad rom download. Download the rim again or get it from a sticky on xda.
Also it doesn't matter what com port Odin puts the phone on as long as it sees it.
Sent from my SPH-L720 using xda app-developers app

tordsrv 1892
im still fairly new at the whole rooting scene. could you possible link me to the stock rom? oh btw idk if this would matter but i think i had the MF9..
i just want to go back stock for now and get this phone to work.. than i will try again.. thank you in advance!
my uncle also said there is a odin file not the program. but an odin file that you use with odin program. is this true for the s4? if so could you link me to it also!

i just tried it again. and im getting this error now..
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)

I have read that that download fron QBKing is bad. As a poster above me said, download the rom from XDA instead and redo the process. Also, be sure to use the usb cable that came with your phone as others can cause the same issue. Also....if it fails again, try a different usb port. Good luck
Sent from my SPH-L720 using Tapatalk 4 Beta

could someone link me to the right post that has the sprint stock rom? thank you

texassoljaz said:
could someone link me to the right post that has the sprint stock rom? thank you
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2382188
Last post
Sent from my SPH-L720 using xda premium

and ubuings
ok so.. i downloaded this stock firmware
http://forum.xda-developers.com/showthread.php?t=2258107
and it actually goes futher but than it said i dont have a pit file.. im sorry this is my first time and it is so hard to understand everything.

<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF9FirmwareAIO.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
could someone tell me wht it says no PIT partition? i have tried so many different stocks for the sprint phone.
im sure mines was the MF9. but i also tried the MDL and MDC.

texassoljaz said:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF9FirmwareAIO.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
could someone tell me wht it says no PIT partition? i have tried so many different stocks for the sprint phone.
im sure mines was the MF9. but i also tried the MDL and MDC.
Click to expand...
Click to collapse
Bot trying to scare you here but if you google the pit error people are being told its a faulty motherboard
Sent from my SPH-L720 using xda premium

same thing happen to my boys gs2 when i was flashing a recovery for him... same ishh.. all i had to do is use odin to unroot and flash a stock rom via odin.. its worked for me.. all the phone would do is go into download mode.. thats it.. no recovery and it wouldnt boot.. stuck in download mode.. i plugged it in to my pc.. odin noticed the phone i flashed stock unrooted rom.. phone rebooted at the end and everything was fine..one crazy thing was after that happen i tried to root again and flash a custom recovery and it happen again.. so i had to fix it again.. i just could not root that phone after that.. had to keep it stock.. my buddy was just happy to have his phone he didnt care about root after that!!

texassoljaz said:
OK so this is what i did. so i tried to root my s4, and in odin it said fail. so i took out the battery. and try to turn it on now it has the phone YELLOW triangle and a monitor. it says "firumware upgrade encountered an issue. Please select recovery mod in kies & try again.
what i have tried so far was download the sprint stock and odin it back. i used qbking77 . com the stock i used is linked on that website. which then links me to stockroms.net. so during the process of doing going back to stock it said fail. i read some where that in the id:com on odin, it should say 0:[COM6] and i read some where else that it does have to say com6 it could say com3. i dont know if that matters. and i also read on the forum they say to use another stock rom? is that also if so where can i get one besides from stockroms.net please someone help me..
this is what it says when i try to odin to stock:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Click to expand...
Click to collapse
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app

ROMANTiC KiD said:
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
I tried what you said than it went to this
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
but now i have a loading bar on my phone. so i dont know whats going to happen i will leave it for a while to see what happens.

texassoljaz said:
I tried what you said than it went to this
Added!!
Odin v.3 engine (ID:7)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Complete(Write) operation failed.
Added!!
All threads completed. (succeed 0 / failed 1)
but now i have a loading bar on my phone. so i dont know whats going to happen i will leave it for a while to see what happens.
Click to expand...
Click to collapse
Hmm weird. Redownload the file from qbking77 and delete the extension again. Also try it with a different version of odin for example the one that qbking uses v1.85 (which is also the one I use) and pull out battery and put the battery in and manually set it to download mode and try it one more time. Btw any chance did you get a pop up in your screen saying something about an error of some kind saying about a parameter before?
Edit: Also probably restart computer just in case also.
Sent from my SPH-L720 using xda app-developers app

ROMANTiC KiD said:
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
ROMANTiC KiD said:
Hmm weird. Redownload the file from qbking77 and delete the extension again. Also try it with a different version of odin for example the one that qbking uses v1.85 (which is also the one I use) and pull out battery and put the battery in and manually set it to download mode and try it one more time. Btw any chance did you get a pop up in your screen saying something about an error of some kind saying about a parameter before?
Edit: Also probably restart computer just in case also.
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
no i never never got a parameter error.. i also have window 8 do you think that will affect anything? i will try qbking than update you.. thanks for helping. greatly appreciated!

texassoljaz said:
no i never never got a parameter error.. i also have window 8 do you think that will affect anything? i will try qbking than update you.. thanks for helping. greatly appreciated!
Click to expand...
Click to collapse
Hmm... alrighty. Nah it shouldnt affect anything but you can also try with other computer as well or different version of windows. No problem hope you get it solved soon!
Sent from my SPH-L720 using xda app-developers app

so after trying it. i got a parameter error. what does this mean?

so i end up getting this far.. do you know how to fix this?
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> aboot.mbn
<ID:0/010> NAND Write Start!!
<ID:0/010> tz.mbn
<ID:0/010> boot.img
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!

<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> aboot.mbn
<ID:0/010> NAND Write Start!!
<ID:0/010> tz.mbn
<ID:0/010> boot.img
<ID:0/010> recovery.img
<ID:0/010> system.img.ext4
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
i dont get it. so i got it to start the green bar in on odin.. than all of a sudden it say fails. and one my phone the blue bar went half way

yessss!!!!! i got

[q] need help with my s4 gt-i9505

can someone please help me , i tryed to put a new rom on my phone and ended up with it giving me and error saying firmware upgrade encountered an issue please select recovery mode in kies, ive tryed to restore in kies but when i do it ends up saying device not found and failing, i can still get onto download mode
ive tryed diffrent odins and same error all the time the last thing i tryed was full wipe and rebuild still no joy
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> PDA_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> MODEM_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> CSC_FULL_WIPE_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!

Help is simple you are in the wrong forum this is I9300 .
Use the report button for moving the post .
Based on your previous posts you are either not following the instructions or need a service centre repair .
jje

SAMGS4 said:
<OSM> BOOTLOADER_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> PDA_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> MODEM_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
<OSM> CSC_FULL_WIPE_I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8.tar.md5 is valid.
Click to expand...
Click to collapse
Mh, is this normal for ODIN, having a single PDA file given?
@ SAMGS4: What exactly did you do? For me it looks like you put the same file in all file selection lines.
Do you still have access to phone's UI and can check the complete device properties?
I know this is the wrong device forum but if a mod moves this topic to the proper location, the replies got moved also.

someone please help
HSishi said:
Mh, is this normal for ODIN, having a single PDA file given?
@ SAMGS4: What exactly did you do? For me it looks like you put the same file in all file selection lines.
Do you still have access to phone's UI and can check the complete device properties?
I know this is the wrong device forum but if a mod moves this topic to the proper location, the replies got moved also.
Click to expand...
Click to collapse
thanks and ive just reported the post to be moved, and also i have no access to the phone, i can get it on the download mode and when it says about firmware upgrade kies update etc

Well ... there might be another reason why you can't flash the wanted file - the DL is corrupt. But ODIN checked the md5 hash and the file passed the test.
Did you try to flash another, earlier leaked, ROM for your phone?
Does the ROM match to your country / provider code? Maybe the ROM you try to flash doesn't match exactly to the phone you have; there are various SGS4 models.

someone please help
HSishi said:
Well ... there might be another reason why you can't flash the wanted file - the DL is corrupt. But ODIN checked the md5 hash and the file passed the test.
Did you try to flash another, earlier leaked, ROM for your phone?
Does the ROM match to your country / provider code? Maybe the ROM you try to flash doesn't match exactly to the phone you have; there are various SGS4 models.
Click to expand...
Click to collapse
just tryed a new rom and pit file and heres the results
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!

my phone was on the (3g) three network uk its a gt-i9505 if someone could direct me to a rom and pit file for my phone i could try would be very much appreciated
heres my LAST ODIN FLASH TRY seems to for got bit further then last time and on my phone i got a little bit of a blue loading bar then it failed

SAMGS4 said:
my phone was on the (3g) three network uk its a gt-i9505 if someone could direct me to a rom and pit file for my phone i could try would be very much appreciated
heres my LAST ODIN FLASH TRY seems to for got bit further then last time and on my phone i got a little bit of a blue loading bar then it failed
Click to expand...
Click to collapse
While flashing using odin make sure no kies programme are running in the background
U can try different cable / usb ports etc will work and try using without pit,
U should use pit file as a last option for now u try without that and do as above will work
.

I Just tried a diffrent usb port and didnt use the pit file and it got a bit futher then first time but failed again here is the results <ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!

someone please help
i just tried diffrent usb post and made sure kies or no firewall was on , didnt use the pit file like you said and phone got bit futher then first time but still failed here the results
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!

U
SAMGS4 said:
i just tried diffrent usb post and made sure kies or no firewall was on , didnt use the pit file like you said and phone got bit futher then first time but still failed here the results
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
I9505XXUBMEA_I9505H3GBME3_I9505XXUBMEA_HOME.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Odin v.3 engine (ID:6)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
boot.img
NAND Write Start!!
recovery.img
system.img.ext4
Complete(Write) operation failed.
Added!!
All threads completed. (succeed 0 / failed 1)
Removed!!
Added!!
Click to expand...
Click to collapse
Did u close all the kies programme from the background that must be the issue
Or uninstall kies and try
There should be 3 four kies file running in the background close all from task manager try restarting pc and try

someone please help
just uninstalled kies and tryed same as before

someone please help
i have a laptop with windows xp on it should i try on this??

OTE=SAMGS4;44354942]i have a laptop with windows xp on it should i try on this??[/QUOTE]
I'd give it a try. Update the drivers before you attempt it. I'm on three as well and have flashed the same firmware without problems. Have you tried flashing a recovery and wiping the phone. Internal SD etc? Wouldn't do it any harm

someone please help
symondo12 said:
OTE=SAMGS4;44354942]i have a laptop with windows xp on it should i try on this??
Click to expand...
Click to collapse
I'd give it a try. Update the drivers before you attempt it. I'm on three as well and have flashed the same firmware without problems. Have you tried flashing a recovery and wiping the phone. Internal SD etc? Wouldn't do it any harm[/QUOTE]
hi could you please give me a link to stock rom for three please as cant find one and what recovery would i flash?? thanks?

Mh, can you get into Recovery mode? If not, flash an alternate Recovery mod first. Try PhilZ Touch Recovery. It's being flashed within DL mode, fill only PDA field.
Ah, I didn't notice yet ... you use ODIN 3.04. That's an outdated version; maybe 3.04 can't handle an I9505.
Most current version is 3.07, get it here. In this post it's said ODIN 1.85 can already deal with an I9595; try this too.
Does ODIN run with Admin rights? Maybe there's a problem with your Windows UAC.
//HSishi

http://forum.xda-developers.com/showthread.php?t=2281367
That's the link for philz recovery. Download the latest .tar and flash in O.
Boot into recovery and wipe everything including the internal SD. Make sure you back up.
By the looks of it you are flashing the latest three firmware. MEA H3G.
I'd download the firmware again. You can get it from Sammobile.com. you'll need to register an account. Think its labelled as Hutchisons 3G

someone please help
i just tryed to flash PhilZ Touch Recovery and it failed, also ive tried all the odins and the one that seems to get me the furthest is the 3.04

someone please help
anymore ideas?? pls:crying:

Have you tried another PC, one with Win 7 or 8 on it?It doesn't look like a partition problem, it seems to get further through each time but keeps failing. Might be a problem with your PC...
Oh, and I use ODIN 3.04 to flash too...

[Q] unbrick error with odin

Hello guys,
Today I tried to unbrick my cm11. I want back official stock rom but I have some troubles with ODIN.
I tried each version of ODIN and still I fail to pass.
ODIN error
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUGNG8_I9505OXXGNG2_I9505XXUGNG8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Removed!!
Click to expand...
Click to collapse
I tried with a PIT file and without. still didn't succeed

PaLiT said:
Hello guys,
Today I tried to unbrick my cm11. I want back official stock rom but I have some troubles with ODIN.
I tried each version of ODIN and still I fail to pass.
ODIN error
I tried with a PIT file and without. still didn't succeed
Click to expand...
Click to collapse
Hi,
.pit might be broken (I guess). Grab a copy of a good .pit file and flash it together with your firmware. If still doesn't, your device might be Hard Bricked.

krasCGQ said:
Hi,
.pit might be broken (I guess). Grab a copy of a good .pit file and flash it together with your firmware. If still doesn't, your device might be Hard Bricked.
Click to expand...
Click to collapse
You need to calm down with saying it is hard bricked. This is not the first time I see you post this warning about hard brick. I see you are a new member and it's good that you try to help people. But it is almost impossible to hard brick our device.
Try a different usb port, diferent cable etc.

the problem has been solved guys thanks!