Related
Hello XDA-devs forums,
I'm having an issue since yesterday.
I have rooted my Huawei Ideos X5, and it ran fine for a day or so.
However, when my battery ran out it shut down into a completely blue screen.
When I tried booting it again, this just showed me a blue screen as well.
Now, I fixed this issue by connecting the phone to my PC after booting it with the Vol+ and Vol- pressed.
(So you get the pink/purple screen)
However, when I opened the phone on my PC, all I saw was a "239 MB" "empty" space, and it should have ~2GB..
I placed a backup copy I saved of my "image" folder in that 239 MB storage, and it booted.
However, today I hooked it up to my PC again to see if it magically changed..
And I couldn't access the 239 MB space anymore.
When I tried fixing the issue with a reboot of the phone, that just caused it to get stuck in a booting loop.
So now I'm stuck with a phone that keeps trying to boot itself,
and I can't access it on my windows PC.
I can, however, access 4 different folders of the phone on my linux notebook.
Now, my question is: can someone with a good understanding of problems like these please help me out?
I'm getting kind of fed up with it, as I've only got the phone for 2 days now.
Thank you in advance, and thank you for taking the time to read this.
Have you tried removing the battery for 5 minutes and then putting it back in?
After this, what happens when you press VOL+ and Power?
How about if you press VOL+, VOL- and Power, without the USB cable?
Hello Katu, thank you for posting.
Regarding your questions:
Yes, I have tried to take out the battery for 5+ minutes- it didn't change anything to the situation unfortunately..
If I press VOL+ and Power at the same time, the device boots into recovery mode.
In this I have tried to format the device in order to reset it to factory defaults, but this did not help either.
When I press VOL+, VOL- and Power, the phone boots into the pink/purple screen.
Can you try a custom recovery and a custom rom? I want to see if your onboard flash is borked.
u8800,cm7,[email protected]
I had the same when my phone got f*ucked up. Put the image folder, than download official rom, like b138 and install it. then check your imei. There is a change that it will be 0.
PlanDreaM said:
Can you try a custom recovery and a custom rom? I want to see if your onboard flash is borked.
u8800,cm7,[email protected]
Click to expand...
Click to collapse
Well, I used an original ROM:
U8800 V100R001C00B136(Overseas General version)
And that resulted in the boot.img being corrupted, so I can't even overwrite that anymore.
Also, this is what I see when I hit VOL+, VOL- and Power at the same time to boot into safe mode, and connect it to my PC.
img69 [dot] imageshack [dot] us/img69/244/10101191548pm.png
julle131 said:
I had the same when my phone got f*ucked up. Put the image folder, than download official rom, like b138 and install it. then check your imei. There is a change that it will be 0.
Click to expand...
Click to collapse
I installed the official B136 rom, and after it rebooted, it would just hang on a black screen.
(it used to show the IDEOS or Android logo when it booted)
Hmm mine came with this Rom
U8800 V100R001C00B135SP01 ( general )
Looking at your name you're from the Netherlands ( so am I )
where did you get this 136 version from ?
I would try to put this one on it
You have to put the 'dload' folder into the root of your SD Card,
then boot into boot-loader, after that it'll automatically flash back to the stock Rom.
1 Format SD card
2 On the SD card, create "dload" folder
3 Put the unzipped Rom into "dload" folder
4 Then boot to bootloader (pink screen)
Yes, mine came with that version as well.
However, I couldn't find it anymore and thus downloaded the version I said earlier.
Also, I did everything as you described, except step 4.
You have to boot to recovery instead of bootloader. (VOL+ and Power)
Anyways, I managed to get ClockworkMod's recovery.img on my phone,
and from there on install a custom ROM on the phone, which magically got it working again - even though it didn't work earlier.
Thank you for reading my thread and taking the time to reply to it.
My issue has been resolved.
just for the record, flashing a stock rom is different from flashing a custom rom..
the 4 steps described by Gman2oo6 is the correct way to flash a stock rom (and it is written clearly in the document that is in the stock rom zip file)
[edit]
step (1) is not a necessary step though..
Yeah, I noticed that.
What I did was format my SDcard with FAT32,
and put a custom rom (update.zip) on the SDcard.
I then booted ClockworksMod Recovery and installed the custom rom from the SDcard.
When I tried installing the stock rom, I just followed the PDF file's instructions that came with the stock rom.
hey i udated to GB 2.3.4 (official)and i didnt like the it cuz the wifif ddnt work and the bluetooth also the DATA so itryed to downgrade to 2.2.2 original official and it did the 2/2 steps intalled and when it restarted it did not want to turn on all that happened was it vibrated and thats all so i left it on like that and when the battery died i plugged it in to the AC and the LED turned on red and the touch kkeys also but not the screen so i really NEED help!
Try to turn it on with lead connected but no battery and see if you can start it.
My battery also went dead flat this morning and I couldn't get it started at all till I tried this. Once I got it started the only thing I could do was quickly pop in the batery and let it charge. Just leave off the cover till you get it going.
I have to add that I did not have the problem of a failed update to deal with but it may at least get you started
i tryed it
nope nothin good happened all that happens is a blank screen with nothin on ,LED is off and the touch keys are off. it justz vibrates and when i put the battery it turn the LED on to red and the touch keys turn on but then like 5 min later the LED and keys turn off
astewart said:
Try to turn it on with lead connected but no battery and see if you can start it.
My battery also went dead flat this morning and I couldn't get it started at all till I tried this. Once I got it started the only thing I could do was quickly pop in the batery and let it charge. Just leave off the cover till you get it going.
I have to add that I did not have the problem of a failed update to deal with but it may at least get you started
Click to expand...
Click to collapse
ok heres what i did i wanted to upgrade my phone to the newest version GB 2.3.4.So what i did was download the update and i followed the installation steps i successfully updated to Gb 2.3.4. so like i was checking how it look and the new feature but when i wanted to go on the android market i went to setting and turn on the wifi and it said Error and then i tried the Bluetooth and it said Error also so then i put my SIMs card in and i was like imma use DATA then and when i restarted my phone it had service but no HSPA+ or Edge or GPRS so like i just hatted my phone from their so then i was trying to root it but iddnt know how to do that so like i read this website and i got the UPDATE.APP or 2.2.2 AT&T did the same steps of the installation of BG 2.3.4 and it went to the process and 1/2 stepp good it passed and then 2/2 also passed it installed it and when it said Successively Installed it said Restarting and the scrren turn of and it vibrated and thats all that happened and i left it like that for the whole days and nothing happened
Do u got any idea?
When i connect it to my laptop it says installing drivers .then its says sucesfully installed drivers ready to use. so then i got to Device Manger and i check what has been installed and their it said USB Human interface device and HID-compliant device WHAT DOES THAT MEAN??
Not sure about the HID (human interface device) probably just the way windows sees the device for interfacing with it. With regards to the not booting I have read a lot of people saying that you need to factory reset and clear cache after the upgrade/downgrade. With the phone off, turn it on by long pressing volume+ and power on button till you get the blue recovery screen and from there you can reset factory/ data and also clear the cache. from what I see this should clear up the problem and start up. Please read this thread, it may help you somehow..... http://forum.xda-developers.com/showthread.php?t=1420728
Hope this helps a little
U mean Boot recovery and imma try it and thanks ill check it out
Sent from my MB300 using XDA App
all that i know is that if u customized your partition, it'll bootloop,
so go back to stock-partition ^^
How do I do that got like the steps or video?
Sent from my MB300 using XDA App
when i downgraded to 2.2.2 i installed this V100R001C00B138SP04CUSTC185D002
http://forum.xda-developers.com/showthread.php?t=1251250 got it from that link
Looks like you are not having much luck. Did you try to factory reset?
astewart said:
Looks like you are not having much luck. Did you try to factory reset?
Click to expand...
Click to collapse
well how do i do that do i need to got to the purple/pink screen or bot recovery cuz i cannot access that my phone doesn't do anything pretty much
Hi everyone, I'm a new member to the forum, but have been a follower for quite some time.
Let's start by introducing my device wich is:
EEEPad Transformer TF101G with ICS running the latest WW_9.2.2.6 firmware.
The device is rooted and running ASUS stock recovery.
Everything was working fine until I decided to do a Cold Boot.
It got stuck on the cold boot menu for like 3 hours and I decided to turn it off.
After that it got stuck on the inicial Asus splash screen. I forced it to turn off a couple a times and it eventually booted up.
I knew something wasn't right, so I backed up all my files and applications.
Then decided to do a factory reset through POWER + VOL-
After that it never booted again, and after a few seconds on the splash screen I hear a click noise, like the hard drive is turning off.
When I try force it to turn off, it starts up again automatically.
I've tried to flash it through nvflash, but being a TF101G it also means it is sbkv3, wich is not supported by nvflash.
Also tried boot recovery tools, but it won't even start, because as I try to connect it to the computer through adb mode, after that "click" noise, the device becomes disconnected.
I didn't try any dangerous applications and stuff like that, just decided to do a simple cold boot, the device is a week old.
If I'm posting this in the wrong section I apologize.
And hope someone can come up with a good idea.
Thanks in advance.
Obviously somethings corrupted and in my opinion the only way to fix it would be to reflash the rom in apx mode using nvflash but that doesn't seem to be possible for your device as of yet but if everything is still stock maybe you can unroot the device (or play dumb) and get it replaced under warranty?
I don't think I can unroot it, since it won't run abd mode.
I'm trying to find a way of not having to send it to warranty.
Saving it as a last resort...
Akusura said:
I don't think I can unroot it, since it won't run abd mode.
I'm trying to find a way of not having to send it to warranty.
Saving it as a last resort...
Click to expand...
Click to collapse
Eek.. since it was factory resetted I think you need to send it to warranty. Not much we can do now with just a splash screen on sbkv3
I don't consider myself an advanced user.
But I really did search everywhere and I got the idea that only with APX and without a compatible NVFlash I was screwed.
But I still had some hope.
Do you think they will give me trouble because of it being rooted?
I my opinion I don't think they will ever know, because It won't boot, It won't run recovery mode (stock) and nothing else at all, the only way to fix it is to flash it, but maybe I'm just being naive.
I treated it with all the care in the world, so only by divine intervention it is a hardware problem.
But you never now...
you should be ok (should)......
i done pretty much the same thing to a customers TF and Asus fixed it no problem.
The fact is that I actually didn't do anything wrong.
Just a cold boot that didn't work, followed by a a factory reset...
How long did it take for yours to get fixed?
I have an a500 with a thor 3.2 rom. I recently used CWM to reset to factory to install the Thor ICS v170 rom. I got an error when restarting into recovery to install it so I restarted again. There it hung up on the logo. So I restarted into recovery holding the power and volume down, but here is where it goes nuts. Once into recovery, the tablet vibrates nonstop and a Team Rogue logo comes up in the background and gives me errors for reading system data and cache. It gives me menu items listen but doesnt let me do anything and I have to Hold power to power down. Still even restarting doesnt get past the Acer boot logo. Please help me out!
Staples01 said:
I have an a500 with a thor 3.2 rom. I recently used CWM to reset to factory to install the Thor ICS v170 rom. I got an error when restarting into recovery to install it so I restarted again. There it hung up on the logo. So I restarted into recovery holding the power and volume down, but here is where it goes nuts. Once into recovery, the tablet vibrates nonstop and a Team Rogue logo comes up in the background and gives me errors for reading system data and cache. It gives me menu items listen but doesnt let me do anything and I have to Hold power to power down. Still even restarting doesnt get past the Acer boot logo. Please help me out!
Click to expand...
Click to collapse
That's what happens when you run stuff from Dev's that don't adhere to GPL. Undoubtedly some leftover code from whomever it was taken from and "somebody" didn't bother to clean it out all the way. FYI, Team Rogue did ICS development for the Xoom tablet, and also some early CWM work. Guess we know where "somebody" got some code from
Ok, back to your current issue at hand. For starters, you're probably still on an HC Bootloader and probably running a really old version of CWM recovery. If you are going to run ICS or JB roms, I highly suggest you upgrade your bootloader to the patched ICS Unlocked bootloader. Also, I would update to the latest version of CWM. You can get it at his site.
I believe your next rom may be able to run on an HC bootloader, or so I've heard, but your CWM needs to be updated, and that's what probably threw out the errors.
You can find a guide for the unlocked bootloader installation in the Dev Forum. It's stickied.
Hope this fixes your issue. If not, post back.
MD
Staples01 said:
I have an a500 with a thor 3.2 rom. I recently used CWM to reset to factory to install the Thor ICS v170 rom. I got an error when restarting into recovery to install it so I restarted again. There it hung up on the logo. So I restarted into recovery holding the power and volume down, but here is where it goes nuts. Once into recovery, the tablet vibrates nonstop and a Team Rogue logo comes up in the background and gives me errors for reading system data and cache. It gives me menu items listen but doesnt let me do anything and I have to Hold power to power down. Still even restarting doesnt get past the Acer boot logo. Please help me out!
Click to expand...
Click to collapse
All I can say is WOW!!
linuxsociety said:
All I can say is WOW!!
Click to expand...
Click to collapse
Yeah, its strange but doesn't surprise me.
OP, your partitions are also undoubtedly messed up as well. I suppose you didn't by chance write down your UID number did you? You may be able to get by with installing an ICS full update zip. Maybe.
MD
Soo...nothing. is it just a piece of junk now?
Staples01 said:
Soo...nothing. is it just a piece of junk now?
Click to expand...
Click to collapse
I wouldn't think it is 100% bricked, but I'd definitely ask on tegraowners.com since it is from one of their recovery/roms. Guess you may have already asked Thor about the issue though?
I have my cpuid but when i run the dotnetdetector to update the usb doesnt stay connected long at all.
Staples01 said:
I have my cpuid but when i run the dotnetdetector to update the usb doesnt stay connected long at all.
Click to expand...
Click to collapse
Are you trying to manipulate the A500 from a Windows PC or Linux? Notice you said Dotnetdetector, sounds like windows, but not familiar with it exactly. Maybe you could try using a live linux distribution (such as Ubuntu or Fedora) to try to get fastboot/adb and reflash the recovery partition with a known working recovery for A500. The teamrogue thing still puzzles me and I'm just curious if bits of Team Rogue's code has been pieced in with the A500 recovery you are trying to use, or if you may have got a hold of a recovery that was for a different device ? I'm not trying to say that you are a nub and flashed a recovery for the wrong device, but there is a possibility depending on where you obtained the rom from, that it could have been mis-labeled for your device ( but been for a different one) If it was for a diff device it would make sense why you can't do anything with it.
Let me get it straight how this happened.
1. You had CWM installed for A500 and recovery was working fine
2. You used CWM to try to flash a Thor ROM, in which the installation failed.
3. After reboot you have nothing but the Acer logo
4. When you boot back into recovery, it is no longer CWM, but a Team Rogue logo is displayed, and that is all you see?
That's the way I interpret the issue you are having anyway. Can you please send me a link to the ROM that you tried to install that triggered all of this. That way I can see exactly what the installer script attempted to do (because it very well could have tried to flash a diff recovery to your device and failed on something else)
Hope we can get things straightened up for you. Good luck again bud
Was using tablet and just playing a game -- tablet reset, robot with ! showed up.
After that, reboots bring me only to the Acer screen.
I can do the VOLUME UP + POWER -- vibrates, powers up, toggle the switch, let go of power button and it does:
ERASING USERDATA...
ERASING CACHE...
Then it reboots back to the ACER logo, and just sits there. I have downloaded one of the ROMs and done the VOLUME with POWER BUTTON start up and it doesn't do anything. Just stays at ACER logo.
I've looked at quite a few things here on the forums and it hasn't done me any good -- nothing seems to want to work with the tablet unless it's in debug mode (which means it has to be a working tab). When connected to a PC it does detect as an MTP USB DEVICE and says "THIS DEVICE IS WORKING PROPERLY." But I can't get much of anything. The only thing I've used that remotely works is USBDEVIEW which gives me the device info including a serial #, which I understand is NOT the cpuid. I do have the box, so I guess that would have the CPUID? Any help appreciate. More than willing to just blast this thing with a one touch factory reset from the PC, if it will just connect.
If you had it at the dead android guy, it means you probably didn't have the decrypted "update.zip" on your Ext SD card. If you had stock ICS running before, you can try downloading those 4 update.zips I posted a few threads ago. Will have to try each one, and hopefully one of them works.
Here's the post...
http://forum.xda-developers.com/show...54&postcount=2
This would be the first thing I try.
MD
Moscow Desire said:
If you had it at the dead android guy, it means you probably didn't have the decrypted "update.zip" on your Ext SD card. If you had stock ICS running before, you can try downloading those 4 update.zips I posted a few threads ago. Will have to try each one, and hopefully one of them works.
Here's the post...
http://forum.xda-developers.com/show...54&postcount=2
This would be the first thing I try.
MD
Click to expand...
Click to collapse
It went to the Dead Android guy when it rebooted after a crash. I haven't seen it since. Just got to the Acer logo screen and stops.
Your linked post is going to what it actually shows instead of the real link.
Fastboot
Sent from my Kindle Fire using xda app-developers app
Vintage144 said:
Fastboot
Sent from my Kindle Fire using xda app-developers app
Click to expand...
Click to collapse
Don't think he has V8 bootloader Mate.
Moscow Desire said:
If you had it at the dead android guy, it means you probably didn't have the decrypted "update.zip" on your Ext SD card. If you had stock ICS running before, you can try downloading those 4 update.zips I posted a few threads ago. Will have to try each one, and hopefully one of them works.
Here's the post...
http://forum.xda-developers.com/show...54&postcount=2
This would be the first thing I try.
MD
Click to expand...
Click to collapse
I'm also stuck at the ACER logo. I d/l'd all four of the zips from your link. All four appear to install correctly but when the flash finishes and the tablet reboots, it's still stuck at the logo.
Also, when I just tried the link again, it is no longer working.
where were you coming from when you tried this ? what BL? gb?JB? what recovery , theres a alot of reading to be done with this device Acer didnt make it easy , but if you read and take it slow there are/were some great devs that left the door open for us all to use these ? Explain where your started from and how you got to where you are now? (Moscow is a sharp dude he can help)!
Vintage144 said:
where were you coming from when you tried this ? what BL? gb?JB? what recovery , theres a alot of reading to be done with this device Acer didnt make it easy , but if you read and take it slow there are/were some great devs that left the door open for us all to use these ? Explain where your started from and how you got to where you are now? (Moscow is a sharp dude he can help)!
Click to expand...
Click to collapse
I bought the tablet used and it would loop on the green "ANDROID" screen. So I don't know what version it was on. I tried the volume +, rotation left and power on to clear the cache and user data. After that it hangs at the ACER screen. I'm assuming it had HC because it has standard recovery. IOW, if I hold the volume - when powering on, it goes to the green Android logo and if an "update.zip" file is present, it will flash it. I've tried just about every "full" ROM I can find and most of them flash but none of them get past "ACER".
I've tried pushing the reset button while powering on while connected to both a Linux box running Mint 15 and a Win7 box. The Win7 box see the tab but won't load the driver. Even though I d/l'd the USB driver from the Acer site. Mint 15 sees the tab but comes up with the error box saying it can't be mounted.
EDIT:
UPDATED POST AT THE BOTTOM!
Hey guys,
flashed czechops CM 10.2 a while ago everything was running fine.
On Saturday i decided to let the battery drain completely to do a full recharge. That`s when the Problems started.
After booting the Phone up i was stuck in a Bootloop with the Cyanogenmod Logo turning around and around and around and so on.
Okay i thought let`s reboot and see what happens.
Still the same.
I then booted into recovery by holding the x button on the keyboard and power and then when the androind in the triangle showed up using vol + and vol - to get into recovery.
I then deleted the cache and rebooted again (No full wipe to factory default trying to avoid that).
After that the phone turned on saying Android is getting updated Updating Package x of y.
After its done its now stuck in Apps getting started.
After i found out to get to the Bootmenu i decided to check the Recovery Menu there.
I can choose between Motorola Stock Recovery (the normal one i already was on)
and Team Win Recovery.
So i choose Team Win Recovery and thought okay since its not working im gonna install the Update of czechops 10.2
Installing itself worked fine. But now im stuck in the same loops.
Currently im goind a Backup of the System with the Team Win Recovery in the hope i wont loose the data even if what im trying to avoid a full factory wipe.
What kinda poped in my eyes when i started the recovery was that it said E: Unable to locate '/boot' partition for backup.
Could this be the problem which is stopping the phone from booting correctly?
And if so how can i fix it?
Hope anyone can help me,
Kind Regards,
Invi
I had te same problem before doing a clean install.
I don't know why but, if you install the android 10.0 tezet and from there start the gapps, creating a account and installing your apps, you do not have problems to install the 10.2.
Good luck.
Sent from my A953 using xda app-developers app
jonasgitz said:
I had te same problem before doing a clean install.
I don't know why but, if you install the android 10.0 tezet and from there start the gapps, creating a account and installing your apps, you do not have problems to install the 10.2.
Good luck.
Sent from my A953 using xda app-developers app
Click to expand...
Click to collapse
Thanks for the heads up jonas.
Unfortunately its too late its seems. My Milestone is just a stone now it seems.
After trying to install 10.2 12.03.14 and that not working correct after doing a full factory wipe i decided to install cm 11 from czechop.
Unfortunately it seems it failed.
My milestone just boots up and stops at the First Logo. No lights. No chance to get in any recovery mode except the normal one.
Bootloader was working some time but stopped cause the Battery is almost empty.
The Problem is i cant even load the Phone anymore cause as soon as i put it on a charger it boots up and wont get enough battery power to live for a few minutes.
So the only thing left working is the normal Android 3e Recovery. Hope i can do anything from there.
Don't give up.
Your problem it's normal, you fisrt need a global battery charger to recharge your battery.
After it, go to boot recovery, you must turn on the milestone holding " volume down + camera" or "volume up + camera", than you need to uses the RSD Lite to reflash your milestone 2.
Normaly, when do you came from another room, you stay in boot loop, so you need to entery in Miestone recovery, "x + volume down" than after it you do a factory reset. It will boot normaly after that.
To go to boot recovery, you must turn on.
Try harder.
(Guys, lets try to help a little)
Sorry about my poor english
I wont. Already ordered an global battery charger yesterday. In the mail from the store delivery is 7-10 Weekdays.
Good thing i have a second cellphone which i can use in the meantime.
i had a similar scenario
Invisan said:
Thanks for the heads up jonas.
Unfortunately its too late its seems. My Milestone is just a stone now it seems.
After trying to install 10.2 12.03.14 and that not working correct after doing a full factory wipe i decided to install cm 11 from czechop.
Unfortunately it seems it failed.
My milestone just boots up and stops at the First Logo. No lights. No chance to get in any recovery mode except the normal one.
Bootloader was working some time but stopped cause the Battery is almost empty.
The Problem is i cant even load the Phone anymore cause as soon as i put it on a charger it boots up and wont get enough battery power to live for a few minutes.
So the only thing left working is the normal Android 3e Recovery. Hope i can do anything from there.
Click to expand...
Click to collapse
hi, I had a similar situation to that earlier today, in that I got to the situation where on boot up I got the Motorola logo then nothing else (I was trying to install C.M. 11 from 10.2 but when it went to install got a message E;// error - verification signature installation aborted), after major panic thinking I'd bricked my milestone, I tried starting the phone in bootloader mode (press camera, volume up and power buttons at the same time) which gives a black screen saying boot loader 70.13 and towards the bottom says boot menu, connect USB, then on your pc find program MOTOROLA SOFTWARE UPDATER (hope you've got it) open the program, it'll say connect a device plug your phone in and let it do it's stuff, takes about an hour (charge your battery using a desktop battery charger beforehand) and your phone will be returned to the stock Motorola rom but at least your phone isn't a brick and you can always start again trying cyanogenmod.
hope this helps
mark13_2001 said:
hi, I had a similar situation to that earlier today, in that I got to the situation where on boot up I got the Motorola logo then nothing else (I was trying to install C.M. 11 from 10.2 but when it went to install got a message E;// error - verification signature installation aborted), after major panic thinking I'd bricked my milestone, I tried starting the phone in bootloader mode (press camera, volume up and power buttons at the same time) which gives a black screen saying boot loader 70.13 and towards the bottom says boot menu, connect USB, then on your pc find program MOTOROLA SOFTWARE UPDATER (hope you've got it) open the program, it'll say connect a device plug your phone in and let it do it's stuff, takes about an hour (charge your battery using a desktop battery charger beforehand) and your phone will be returned to the stock Motorola rom but at least your phone isn't a brick and you can always start again trying cyanogenmod.
hope this helps
Click to expand...
Click to collapse
So i downloaded Motorola Software Updater and RSD Lite + Motorola Device Manager newest Version
Unfortunately my Milestone seems not to be recognized by either Software updater nor RSD Lite.
In the Device Manager S Flash OMAP3630 shows up and is recognized.
Im running Windows 8.1 x64 and on a second Computer Windows 7 x64
What tool can i use ander Linux? Maybe the Phone will be recognized there.
EDIT:
K found it. Doing it with Linux at the Moment. Its working.
Only need to Root it then and after that flash my old Files and hope they are working.
At least i have an old Backup i made from Tezet before going up to 10.2 which i made with Clockworkmod
Hope it will work and not be broken like the one i made with Team Win Recovery.
Anyone knows how i can change stuff in a Team Win Backup?
Invisan said:
So i downloaded Motorola Software Updater and RSD Lite + Motorola Device Manager newest Version
Unfortunately my Milestone seems not to be recognized by either Software updater nor RSD Lite.
In the Device Manager S Flash OMAP3630 shows up and is recognized.
Im running Windows 8.1 x64 and on a second Computer Windows 7 x64
What tool can i use ander Linux? Maybe the Phone will be recognized there.
EDIT:
K found it. Doing it with Linux at the Moment. Its working.
Only need to Root it then and after that flash my old Files and hope they are working.
At least i have an old Backup i made from Tezet before going up to 10.2 which i made with Clockworkmod
Hope it will work and not be broken like the one i made with Team Win Recovery.
Anyone knows how i can change stuff in a Team Win Backup?
Click to expand...
Click to collapse
I did find it took a long time for the Motorola software updater (about 20 mins) to detect my milestone 2 (I'm using windows7 x64), I'm thinking the mistake I made when trying to upgrade to CM 11 was I didn't wipe data/cache before trying to install it
mark13_2001 said:
I did find it took a long time for the Motorola software updater (about 20 mins) to detect my milestone 2 (I'm using windows7 x64), I'm thinking the mistake I made when trying to upgrade to CM 11 was I didn't wipe data/cache before trying to install it
Click to expand...
Click to collapse
Hi mark,
well Windows popped up saying N/A
when it should show new Software.
It also couldnt recognize my Cellphone correctly it seemed.
But i flashed it with Linux anyways.
Flashing to tezet`s 10 worked also like a charm
and i could install my Backup i made in december before
updating to czechops 10.2.
Guess after i know what to do now i will try to update to cm11 now.
Invisan said:
Hi mark,
well Windows popped up saying N/A
when it should show new Software.
It also couldnt recognize my Cellphone correctly it seemed.
But i flashed it with Linux anyways.
Flashing to tezet`s 10 worked also like a charm
and i could install my Backup i made in december before
updating to czechops 10.2.
Guess after i know what to do now i will try to update to cm11 now.
Click to expand...
Click to collapse
let us know how you get on as I'm tempted to try again (I do like how CM10 gets rid of all the un-necessary apps but gives you control of all the system parameters) but want to step up to CM11 without having the same problem as before.