Database Users

[CWM] for Micromax A35

Here is it,guys! Clockwork Mod for Micromax A35.Only 1 Bug was found.Soon it will be rectified.
Device ; Micromax A35
Processor : Spectrum ***
Download Link for CWM recvery : Download it from here
Instuctions to Flash :
* Install the required packages like adb.
*Download Quickboot.apk and install it in your phone.
*Now Enable USB debugging in your phone by going to Settings->Development->USB Debugging (Skip this step if it is already enabled)
* Open Quickboot & click on Bootloader option.
*After sometime your phone will get stuck at the logo.
*Connect your phone to PC using USB cable.
*Now open the adb folder & inside that folder press & hold the Shift key + right click on blank space & choose Open Command Window Here.
*Now download the given img file,rename it to "recovery.img" and put it into the adb folder
*Now a black cmd window will open, there type fastboot devices
*This should display your device name in fastboot mode, if nothing is shown, then you have to check previous steps again.
*Now Type fastboot flash recovery recovery.img
*Within a sec the process will get over & it will install the CWM.
So Enjoy, you have successfully Install CWM Recovery.img on Micromax A35
Now you can check whether your CWM is working or not:-
Remove battery of your phone and reinsert.
Press Power and Volume Up key to boot into recovery mode.
If it get booted into recovery mode then it mean you have successfuly installed it, if not then try the process again.
Credits : Prashanth Sadasivan
If you have liked my work,dont forget to press the thanks button.

Prashanth Sadasivan said:
Here is it,guys! Clockwork Mod for Micromax A35.Only 1 Bug was found.Soon it will be rectified.
Device ; Micromax A35
Processor : Spectrum ***
Download Link for CWM recvery : Download it from here
Instuctions to Flash :
* Install the required packages like adb.
*Download Quickboot.apk and install it in your phone.
*Now Enable USB debugging in your phone by going to Settings->Development->USB Debugging (Skip this step if it is already enabled)
* Open Quickboot & click on Bootloader option.
*After sometime your phone will get stuck at the logo.
*Connect your phone to PC using USB cable.
*Now open the adb folder & inside that folder press & hold the Shift key + right click on blank space & choose Open Command Window Here.
*Now download the given img file,rename it to "recovery.img" and put it into the adb folder
*Now a black cmd window will open, there type fastboot devices
*This should display your device name in fastboot mode, if nothing is shown, then you have to check previous steps again.
*Now Type fastboot flash recovery recovery.img
*Within a sec the process will get over & it will install the CWM.
So Enjoy, you have successfully Install CWM Recovery.img on Micromax A35
Now you can check whether your CWM is working or not:-
Remove battery of your phone and reinsert.
Press Power and Volume Up key to boot into recovery mode.
If it get booted into recovery mode then it mean you have successfuly installed it, if not then try the process again.
Credits : Prashanth Sadasivan
If you have liked my work,dont forget to press the thanks button.
Click to expand...
Click to collapse
not working at all for me.. rooted my phone but not able to install your cwm on my phone through fastboot... Fastboot shows installation for the recovery done but when I press volume+ and power button, it goes into some blue screen where you can not do anything.... please help

Try it with quickboot
Sent from my XR650 rom by using xda premium

Seems good ! Can you tell mee the version of this recovery ??
Sent from my HTC Vision using XDA Free mobile app

Root Xperia Z1 C6903 14.5.A.0.270 Android 5.0.2 Unlocked bootloader

Update : 03.08.2015 Update with Full Erase it will bring back your best bettery performance.
in the recovery Format the internal SD Storage and update .270. All the steps still same, Before install flashable.zip format your internal SD.... Thats it
Who are in .242 frimware just download the new .270 frimware follow the same steps.... as .242
in this time no need to flash the boot img.....
1.Download Firmware....
2.create FTF File and make Flashable .Zip
3 Copy to External SD ....
4. Before Do anything make a proper backup...in this time you have to format your inernal sd....
5. you have rooted .242 frimware Download Here install Z1 Dual Recovery installer.zip... extract the zip file run the .bat file it will install the recovery
6 boot in recovery... Format the internal SD ....then install the flashable.zip and clear the caches.. Enjoy....
Update : 22.06.2015 dont update .270 Or .283(t-mobile) Firmware its drain's battery quick its only 15 to 16 hours on normal usage....
I am new to XDA its my first Post.....
sorry if any mistake....in my writing...
Root Xperia Z1 C6903 user may Check this method in other Z1 Variant.. not operator customized variant...
this is the simple way to root Z1 in 5.0.2 new stock FTF..
Reqr:-
Xperia Z1 C6903 unlocked bootloader..with android 5.0.2 (.242) & 60%of charge
Xperia flash tool..... Click here with xperia Z1 driver
To Download Xperia Device's Firmware File .FTF Click Here XperiFirm you need to copy .exe to Xperia Flashtool Folder and run from that folder..
PRF Creator.....Click here
SuperSu Binary...Click here
Recovery image....Download here
Dual recovery Flash able Zip file..Downlaod here
Procedure.. Before proceed prepare all reqired file its only take 5 mins.....
Now run PRFC and add all three required files(.ftf,SuperSu,Recovery) in it.
Then click on Create.
Once the Flashable ROM is created, it will show finished. now the flashable.zip file created in the same PRF Creator folder..
Do not touch any other option while creating the pre-rooted firmware.
Now copy the flashable.Zip firmware to the phone’s internal storage
Step 1: Connect the phone with usb Debugging. mode
Step 2: Open the flashtool thunder icon select Fastboot mode...
Step 3:Select option reboot in fastboot mode via adb...(or simply connect phone in fastboot using press volume (+) while connect the usb
Step 4:Again click reboot in fastboot via fastboot
Step 5:Now click select kernel to flash.. now browse (.img extension) and select boot_2.img file download..
Step 6:Now disconnect the phone from pc. boot into recovery using power on the phone its show sony logo the press volume (-)
Step 7:now you are CWM Recovery... install .zip from sd storage ...select the flashable.zip and install it...once finished ..power off the phone using recovery advance option...
Step 8:Now open flashtool in pc select thunder icon select flashmode select .242 firmware in Wipe Option tick APPSLOG, CACHE & untick DATA. in Exclude tick SYSTEM
Step 9: Now Click Flash....Connect the phone Dialog Window Will Appear now connect the phone USB together press volume (-)
release the button when dialog window disappear
now the your pc detect your phone in flashmode and flash the firmware..... only 2 mins completed..
Step 10:Now disconnect from pc. power on the phone ....that's it...now your phone rooted......Enjoy :good:
if any Question's ask me...

Nice share
Sent from my C6903 using XDA Premium 4 mobile app

I cant find the ftf file
please fix
I cant find the FTF file
how can I get that file

bwararsalan said:
please fix
I cant find the FTF file
how can I get that file
Click to expand...
Click to collapse
Download your prefer firmware with XperiaFirm, then create TFT with FlashTool.

anburaj said:
I am new to XDA its my first Post.....
sorry if any mistake....in my writing...
Root Xperia Z1 C6903 user may Check this method in other Z1 Variant.. not operator customized variant...
this is the simple way to root Z1 in 5.0.2 new stock FTF..
Reqr:-
Xperia Z1 C6903 unlocked bootloader..with android 5.0.2 (.242) & 60%of charge
Xperia flash tool..... Click here with xperia Z1 driver
PRF Creator.....Click here
SuperSu Binary...Click here
Recovery image....Download here
Dual recovery Flash able Zip file..Downlaod here
Procedure.. Before proceed prepare all reqired file its only take 5 mins.....
Now run PRFC and add all three required files(.ftf,SuperSu,Recovery) in it.
Then click on Create.
Once the Flashable ROM is created, it will show finished. now the flashable.zip file created in the same PRF Creator folder..
Do not touch any other option while creating the pre-rooted firmware.
Now copy the flashable.Zip firmware to the phone’s internal storage
Step 1: Connect the phone with usb Debugging. mode
Step 2: Open the flashtool thunder icon select Fastboot mode...
Step 3:Select option reboot in fastboot mode via adb...(or simply connect phone in fastboot using press volume (+) while connect the usb
Step 4:Again click reboot in fastboot via fastboot
Step 5:Now click select kernel to flash.. now browse (.img extension) and select boot_2.img file download..
Step 6:Now disconnect the phone from pc. boot into recovery using power on the phone its show sony logo the press volume (-)
Step 7:now you are CWM Recovery... install .zip from sd storage ...select the flashable.zip and install it...once finished ..power off the phone using recovery advance option...
Step 8:Now open flashtool in pc select thunder icon select flashmode select .242 firmware in Wipe Option tick APPSLOG, CACHE & untick DATA. in Exclude tick SYSTEM
Step 9: Now Click Flash....Connect the phone Dialog Window Will Appear now connect the phone USB together press volume (-)
release the button when dialog window disappear
now the your pc detect your phone in flashmode and flash the firmware..... only 2 mins completed..
Step 10:Now disconnect from pc. power on the phone ....that's it...now your phone rooted......Enjoy :good:
if any Question's ask me...
Click to expand...
Click to collapse
im a novice can you please help me
Ive followed up to "Dual recovery Flash able Zip file..Downlaod here"
but i m not sure what to click on once ive opened the link?. I have a z1 c6903 running lollipop 5.0.2 build number 14.5.A.0.242
thanks

seriously the smartest & easiest way to root C6903 14.5.A.0.242 !!!
no downgrade bull***t & useless time-consuming process
many thanks !!

Rooted with this method.. and it's the bomb yo!

Спасибо! Все отлично! Работает!

okay so ive just finished the root and used a app to make sure it is rooted, it is. but i cant access the recovery when i hold the - volume button and plug in the phone the led flashes red then green then goes off. do i have to add my own recovery?
thanks

nikster19 said:
okay so ive just finished the root and used a app to make sure it is rooted, it is. but i cant access the recovery when i hold the - volume button and plug in the phone the led flashes red then green then goes off. do i have to add my own recovery?
thanks
Click to expand...
Click to collapse
AFTER REFLASH(FINAL) WITH FLASHTOOL ITS EARSE THE RECOVERY PARTITION THAT'S THE PROBLEM I AM WORKING ON THAT TOO WAIT..

Problem is I made it work the first few times around. There was recovery and all was good for the first 3 times ( I had to redo the whole process due to the Rock1zk rom I tried to install kept kicking me into bootloop or boot animation hang) and now I can't get it to work anymore. It keeps having the red LED light and no recovery.
There must be something I did right the first few times or something i did wrong after....

mojo1ne said:
Problem is I made it work the first few times around. There was recovery and all was good for the first 3 times ( I had to redo the whole process due to the Rock1zk rom I tried to install kept kicking me into bootloop or boot animation hang) and now I can't get it to work anymore. It keeps having the red LED light and no recovery.
There must be something I did right the first few times or something i did wrong after....
Click to expand...
Click to collapse
R U Tried to install aosp based rom..
power off using powerbutton + volume( +) for few mins
now try to flash via flash tool with Stock Firmware...in flashmode ..

nikster19 said:
okay so ive just finished the root and used a app to make sure it is rooted, it is. but i cant access the recovery when i hold the - volume button and plug in the phone the led flashes red then green then goes off. do i have to add my own recovery?
thanks
Click to expand...
Click to collapse
now i got it :good::victory:
i assume you have root access..and you cann't get in to the recovery...
try to install the recovery in adb ...
Download here "https://mega.co.nz/#!6QtTRCwT!flLlwuSo1hK3_jskHEPqO-Q6jVUXrWF5xoxEyuHN3cI"
run the install.bat....
its hard to get permission on android 5.0
if you got it then you are sucessfully installed the recovery...
if not ...install ROM MANAGER "https://play.google.com/store/apps/details?id=com.koushikdutta.rommanager&hl=en"
under Utilities MENU
Select fix app permission (similar) it will grant root access to all your application...
the restart the Phone ...
now install in normal ADB Mode...
then start install.bat..:good:
:good:
Try you will get It....:good:

Ive tried to check if my device is rooted and I get different answers from different apps??? :/
edit i re did the whole root and i now have root access
Sent from my C6903 using XDA Free mobile app

nikster19 said:
Ive tried to check if my device is rooted and I get different answers from different apps??? :/
edit i re did the whole root and i now have root access
Sent from my C6903 using XDA Free mobile app
Click to expand...
Click to collapse
if you have root access....check your recovery ...if installed ok...
if not use the above method to install recoveries....

Thanks for the help ive figured it out now

can we use this method also on C6902 ?

When I am creating the ftf file in prfcreator ,do I check the include options or do I leave them unchecked?

Astra1 said:
When I am creating the ftf file in prfcreator ,do I check the include options or do I leave them unchecked?
Click to expand...
Click to collapse
PRF Creator does not create TFT but flashable zip file. You should get all options selected. Read more here http://forum.xda-developers.com/showpost.php?p=55082595&postcount=2

Astra1 said:
When I am creating the ftf file in prfcreator ,do I check the include options or do I leave them unchecked?
Click to expand...
Click to collapse
In PRF Creator Don't Touch any tick(option) Simply select your zip(three .Zip files) and then select create...

Flashing CWM for Nokia X2 , Step by Step Guide

So , i Faced the same problem a lot of newbies face when flashing the cwm recovery on xda ... a month ago , i didnt know anything and xda didnt give proper info ... so , this thread is so that other newbies will be able to flash it easily .... Any doubt , pls ask ..... If i am wrong in anything , pls feel free to correct me
Materials Required:-
1. Adb Drivers setup(in the "nokia_x_usb_drivers.zip")
2. CWM For Nokia X2
3. Nokia_x_usb_drivers.zip
4. A Windows PC
5. A Nokia X2
Steps:-
1. Download the two zips in the attachments and extract the adb drivers setup from the nokia_x_usb_drivers.zip
2. run the Adb Drivers Setup
3. type 'Y' thrice and there will be a new folder called 'adb' in ur system disk (example :- Local Disk C)
4. go to fastboot mode in ur nokia x2 by turning the phone off and holding the power button and after the screen turns on , hold both the volume buttons for 3-5 seconds until it gets stuck at the "NOKIA" screen ( or use an app like rom toolbox to reboot into bootloader mode )
5. Now , connect ur nokia x2 to the pc
6. Extract the Nokia_x_usb_drivers folder from the nokia_x_usb-drivers.zip
7. Open "Device Manager" and update the nokia drivers (if it is already showing "Nokia Bootloader Interface" , ignore this step)
8. extract CWM1013.zip and move the CWM1013.img to the adb folder in ur system disk
9. now, run cmd and change ur directory to the 'adb' folder
10. Now , type Fastboot -i 0x0421 flash recovery "CWM1013.img"
11. It will show the progress and it will be done in 5-10 seconds
12. Reboot the phone into recovery by holding power button for sometime till it gets out of fastboot mode and then , hold Volume Up button...
13. Enjoy CWM
:good::good:
this worked perfectly good for my nokia x2 , hope it helps

Does everything works fine?
Any feature not working?
dragonfist453 said:
So , i Faced the same problem a lot of newbies face when flashing the cwm recovery on xda ... a month ago , i didnt know anything and xda didnt give proper info ... so , this thread is so that other newbies will be able to flash it easily .... Any doubt , pls ask ..... If i am wrong in anything , pls feel free to correct me
Materials Required:-
1. Adb Drivers setup(in the "nokia_x_usb_drivers.zip")
2. CWM For Nokia X2
3. Nokia_x_usb_drivers.zip
4. A Windows PC
5. A Nokia X2
Steps:-
1. Download the two zips in the attachments and extract the adb drivers setup from the nokia_x_usb_drivers.zip
2. run the Adb Drivers Setup
3. type 'Y' thrice and there will be a new folder called 'adb' in ur system disk (example :- Local Disk C)
4. go to fastboot mode in ur nokia x2 by turning the phone off and holding the power button and after the screen turns on , hold both the volume buttons for 3-5 seconds until it gets stuck at the "NOKIA" screen ( or use an app like rom toolbox to reboot into bootloader mode )
5. Now , connect ur nokia x2 to the pc
6. Extract the Nokia_x_usb_drivers folder from the nokia_x_usb-drivers.zip
7. Open "Device Manager" and update the nokia drivers (if it is already showing "Nokia Bootloader Interface" , ignore this step)
8. extract CWM1013.zip and move the CWM1013.img to the adb folder in ur system disk
9. now, run cmd and change ur directory to the 'adb' folder
10. Now , type Fastboot -i 0x0421 flash recovery "CWM1013.img"
11. It will show the progress and it will be done in 5-10 seconds
12. Reboot the phone into recovery by holding power button for sometime till it gets out of fastboot mode and then , hold Volume Up button...
13. Enjoy CWM
:good::good:
this worked perfectly good for my nokia x2 , hope it helps
Click to expand...
Click to collapse

but, before doing anything mention above.. we have to root our phone first.. right? because this my problem yesterday.. so I decided to root my phone.. then it worked..

why does it say waiting for device after step 10. ???

there is no adb folder in c drive
please help me where is adb folder

having problem
help .. it is showing
waiting for device .. tell me what to do plz i am a newbie here

hey bro i need help here's a little problem.. may u solve ?

Help zte blade S7 t920 firmware needed

Can anyone please provide me link for ZTE blade S7 t920 firmware download please? My phone got bootloop, factory reset from stock recovery doesn't help phone still unable to boot to homescreen. Been looking all over the Internet but no luck finding the firmware for ZTE blade S7 t920! Been contacted the customer service on Twitter FB page and emails from zte website but they ignore me not giving me reply from like 3 days ago! I feel like being ignored as a customer!
Sent from my 6042D using Tapatalk

Please anybody help, I don't know who else I should ask for help

I do not know whether or not this helps you in any way, since the original post has been made quite some time ago, but it may be worth a try...
This phone was sold in a few countries, and one of them I know about was Thailand. If you look up the corresponding official ZTE support page, you get this:
http://www.ztedevice.com/support/detail?id=CB70AA9C4A8C4F87AB43C34D3608D11E
The direct link to the download is:
http://download.ztedevice.com/support/product/507/6404/sd/20160726173958917.zip
(This phone was also sold in Russia, but the official product page has been removed, and I see nothing on their support page about that.)
EDIT: Browsing some more I also found these:
http://www.ztedevice.com/support/detail?id=220768DC76A54A3DA35058798581D35D
(http://download.ztedevice.com/support/product/502/201607261748731/sd/20160726175804201.zip)
http://www.ztedevice.com/support/detail?id=42960D5BCACB415ABC48079330E92530
(http://download.ztedevice.com/support/product/505/201607121001133/sd/20160712100920696.zip)
http://www.ztedevice.com/support/detail?id=11BDFB5787D145F39F40D7D303539A56
(http://download.ztedevice.com/support/product/599/201609301500128/sd/20160930150633562.zip)
http://www.ztedevice.com/support/detail?id=21C3175244A94B05A966364EE7163FE3
(http://download.ztedevice.com/support/product/508/201612081035893/sd/20161208105528911.zip)
http://www.ztedevice.com/support/detail?id=1EF6B0B3FD624F79AD5668AB53F20D2B
(http://download.ztedevice.com/support/product/509/201607261720789/sd/20160726172926681.zip)
They might not be full ROMs, but should they really help, it would be recommended to directly host them somewhere else too, in case they are removed.
ZTE ROMs are a hard task to hunt down, if this does not help I strongly recommend to dig deeper down into their support page...

Dear Member,
i too faced problem in LYF LS-5021 looks same ZTE S7-T920. i found incomplete rom from internet, which failed in flash & came to dead. Later i found update.zip for LYF in that i found that is same as S7.
I edited rawprogram.xml to file given to download & flashed. After flash phone came alive & updated with update.zip.
Now phone came to normal.
May be it will help for u.... attached updater script of Lyf LS-5021.

Inside the zip's from the ZTE -homepage u gonna find the update.zip file .... which perfectly works for the S7.
So ... is the LYF LS-5021 exactly the same phone as the S7 ... any differences?
New ROMs available?

I would also like to know if there are any updates available for the Blade S7 (other than Lolipop 5.1). I managed to download the update.zip from the ztedevice . com website and followed the instruction and was able to update using the Blade S7 ROM but only Lolipop 5.1 is available. Can anyone confirm if LYF LS-5021 ROM can be used on the S7 and what ROM's are available?

kappwj said:
I would also like to know if there are any updates available for the Blade S7 (other than Lolipop 5.1). I managed to download the update.zip from the ztedevice . com website and followed the instruction and was able to update using the Blade S7 ROM but only Lolipop 5.1 is available. Can anyone confirm if LYF LS-5021 ROM can be used on the S7 and what ROM's are available?
Click to expand...
Click to collapse
The real question is if there is anything official above 5.1 available for the Lyf. Needrom seems to host official 6.0, but it would be nice to confirm that with Lyf support. IDK if they would answer, but you might as well should try your luck with the ZTE ROM compatibility (tough they most likely will not take any responsibility and not advise you to try flashing their ROM). Their support page is here:
https://www.mylyf.com/self-help.html
Also Lyf LS-5021 may be the Lyf Earth?

ЯazoR said:
The real question is if there is anything official above 5.1 available for the Lyf. Needrom seems to host official 6.0, but it would be nice to confirm that with Lyf support. IDK if they would answer, but you might as well should try your luck with the ZTE ROM compatibility (tough they most likely will not take any responsibility and not advise you to try flashing their ROM). Their support page is here:
Also Lyf LS-5021 may be the Lyf Earth?
Click to expand...
Click to collapse
It is the Lyf Earth 2 (or second gen earth). Just checked Needrom and cannot find any rom for Blade S7 . I will check Needrom for official Lyf 6.0. But thanks for the feedback.

ZTE blade S7 T920
I also have a ZTE blade S7 and I know the suffer of finding this phone's firmware... But I am still a Standard android customizer so yeah after searching the web... No firmware found for this phone... So here's what I've done to make a backup..
I rooted my phone using kingoroot via PC
-steps-
-download the kingoroot application on pc
-install the application on pc.
#on the phone#
- battery charged to 100% because of fear the process will fail because of the battery
-enabled unknown sources in
*settings/security/unknown sources*
-enabled developer options
*settings/about phone/Build number(just keep spamming the build number till it says developer mode enabled)
- go back to settings and enable usb debuging
*settings/developer options/usb debuging(tick the box)
-then connect phone to pc then a small box will show up on the phone
tick allow this pc bla~ bla~ and
press ok or accept
#on the pc#
-open kingoroot application
-wait for the application to load
-then press root device
-if the phone shows something that needs to install ,just press install
-Then the phone will automatically change to a blue screen with percentage numbers on screen.
Wait for 10-20 min
-Then on the phone will show up root success with a giant blue tick
-uninstall all the cleaner or battery saver that is installed by kingoroot...
-then reboot phone...
Now find TWRP recovery from xda somewhere for the zte blade s7
The thread
https://www.google.com/amp/s/forum....eneral/zte-s7-blade-recovery-cm-t3567806/amp/
Direct download link
https://drive.google.com/drive/mobile/folders/0B4Ya5mT9NhjqUUZyVTFDT18xQlU
-Download the above file on the phone
- after the download, there will be a file called recovery.img
- open flashify and slide to backup/restore
-backup the current recovery
-after backup slide back to Flash and pick Recovery Image
-pick choose a file and find the recovery.img that we downloaded earlier
And flash
-After flashing is done press flash more and it will leave you on the flash menu...
-press the three dot on the top right or left side (mine is right side)
-choose reboot recovery...
And now twrp will show up...
On first boot to twrp it will ask for allowing to modify the system...
Just swipe the blue circle
And now choose backup
For me, I check all the box to backup everything but the nesesary one is just boot and system...
And wallaahh backup done...
For my recommendation ,backup the file to a memory card and put it in a safe place just for safety.. Because you wont know maybe you'll accidentally deleted the file while formatting...
And that's it... Well done...

Anyone can help?
I need custom rom for zte blade s7

Is there any flashable msm8939.mbn/hex and msimage_8939.mbn for this phone? or any other unbrick method for ZTE Blade S7? I'm searching the net inside out and cant find a thing. Somebody please point in the right direction
I would really appreciate it to the max

We hit a dead end with this phone

I have a way but u need brains to do the following...
-To flash a custom recovery to the phone via sp flash tool or adb
The reason is because I have a backup rom of my zte t920 but it needs a custom recovery to reflash

Jo_bell said:
I have a way but u need brains to do the following...
-To flash a custom recovery to the phone via sp flash tool or adb
The reason is because I have a backup rom of my zte t920 but it needs a custom recovery to reflash
Click to expand...
Click to collapse
Anything is doable at this point. So tell me how am I going to flash a custom recovery? I do have the SP flash tool, so what else do I need?
Can you hook me up with your backup rom? I would really appreciate it

terawyvenx said:
Anything is doable at this point. So tell me how am I going to flash a custom recovery? I do have the SP flash tool, so what else do I need?
Can you hook me up with your backup rom? I would really appreciate it
Click to expand...
Click to collapse
Ok I will upload my backup rom to google drive and link will be sent on completion
I dont think sp flash tool can help on this... Becuase it needs the actual firmware scatter loading file... Which in this case... I dont have... :crying: still finding a way to create the scatter file myself.. No luck..
So.. Adb should be the hero here... But only if u hv usb debuging enabled before
Using a pc or laptop install adb to your pc/laptop from anywhere in xda...
The fastest and easiest is on this thread
https://forum.xda-developers.com/showthread.php?t=2588979
And download the twrp recovery image. From this thread
#the recovey is named recovery.img#
https://forum.xda-developers.com/android/general/tutorial-how-to-install-twrp-zte-blade-t2953998
*1* Download and install the adb on ur pc and put the custom recovery in any folder #inside an empty folder with the recovery is the best choice#
*2* After installing the adb.. Go inside the folder that contains the recovery.img...
*3* #without highlighting any file# put ur mouse pointer at any empty space in the folder , HOLD SHIFT AND RIGHT CLICK ON YOUR MOUSE. And there will be an extra option that says Open Command Prompt here or Open Power Shell here
*4* Try to boot up ur device as far as it can go in this case the zte logo and and on the pc inside the command prompt from *3* and type in adb devices and press enter.. If it shows a reading. Example, F2xhk7 device ur in luck... Go to *5*
.. But if it shows red notes.. . Try changing usb ports and usb cable #in my case before... The computer usb 3.0 port does not read my device.. *the usb port coloured blue*.. so I use other ports and it worked# :fingers-crossed:
If it still does not connect.. Then ur out of luck... The only way is through sp flash tool... Try asking one of the developers to help...
*5* congratulations if u made it here.. :laugh: now back on business...
-Type in adb reboot fastboot and the device will restart to fastboot
-Now type in fastboot flash recovery recovery.img note *the recovery.img must be the duplicate as the name of the recovery* * I repeat the command is. fastboot flash recovery recovery.img the word recovery is meant to be there *
- after the flash ,reboot the device into recovery by typing.
fastboot reboot recovery or either combimation of power and volume up button
If the recovery shows twrp.. Ur in luck then.. :laugh:

Jo_bell, you sir, are the man!:good: ....i will await your Google drive link. Would generating a scatter file require an actual working ZTE blade S7 to do? Or cant it be generated using a tool of some sort?

Jo_bell said:
Ok I will upload my backup rom to google drive and link will be sent on completion
I dont think sp flash tool can help on this... Becuase it needs the actual firmware scatter loading file... Which in this case... I dont have... :crying: still finding a way to create the scatter file myself.. No luck..
So.. Adb should be the hero here... But only if u hv usb debuging enabled before
Using a pc or laptop install adb to your pc/laptop from anywhere in xda...
The fastest and easiest is on this thread
https://forum.xda-developers.com/showthread.php?t=2588979
And download the twrp recovery image. From this thread
#the recovey is named recovery.img#
https://forum.xda-developers.com/android/general/tutorial-how-to-install-twrp-zte-blade-t2953998
*1* Download and install the adb on ur pc and put the custom recovery in any folder #inside an empty folder with the recovery is the best choice#
*2* After installing the adb.. Go inside the folder that contains the recovery.img...
*3* #without highlighting any file# put ur mouse pointer at any empty space in the folder , HOLD SHIFT AND RIGHT CLICK ON YOUR MOUSE. And there will be an extra option that says Open Command Prompt here or Open Power Shell here
*4* Try to boot up ur device as far as it can go in this case the zte logo and and on the pc inside the command prompt from *3* and type in adb devices and press enter.. If it shows a reading. Example, F2xhk7 device ur in luck... Go to *5*
.. But if it shows red notes.. . Try changing usb ports and usb cable #in my case before... The computer usb 3.0 port does not read my device.. *the usb port coloured blue*.. so I use other ports and it worked# :fingers-crossed:
If it still does not connect.. Then ur out of luck... The only way is through sp flash tool... Try asking one of the developers to help...
*5* congratulations if u made it here.. :laugh: now back on business...
-Type in adb reboot fastboot and the device will restart to fastboot
-Now type in fastboot flash recovery recovery.img note *the recovery.img must be the duplicate as the name of the recovery* * I repeat the command is. fastboot flash recovery recovery.img the word recovery is meant to be there *
- after the flash ,reboot the device into recovery by typing.
fastboot reboot recovery or either combimation of power and volume up button
If the recovery shows twrp.. Ur in luck then.. :laugh:
Click to expand...
Click to collapse
So hows the upload coming along?

TWRP 3.1.1-1 Full + Stock B16 for TWRP (Full+Clean)
https://www.androidfilehost.com/?w=files&flid=211817

NFound said:
TWRP 3.1.1-1 Full + Stock B16 for TWRP (Full+Clean)
https://www.androidfilehost.com/?w=files&flid=211817
Click to expand...
Click to collapse
I don't see this will help though. The phone wont boot up, so I cant put the phone in recovery mode or download mode.
So I cant flash TWRP or even do SD card upgrade with it. If there's anything in that firmware from the link you left above that
can help boot up the phone again, please by all means point it out.
I really appreciate it thanks

how do i update to custom roms
NFound said:
TWRP 3.1.1-1 Full + Stock B16 for TWRP (Full+Clean)
https://www.androidfilehost.com/?w=files&flid=211817
Click to expand...
Click to collapse
could you please explain the process of updating to the custom roms from a working S7. please. thx

boot loop

hi ive tried to get a rom back on my moto e4 with no luck and now ive down something and it just stays on boot loop .i have moto e4 xt1761 and im stuck bad .just want to get it back up and running

madman141272 said:
hi ive tried to get a rom back on my moto e4 with no luck and now ive down something and it just stays on boot loop .i have moto e4 xt1761 and im stuck bad .just want to get it back up and running
Click to expand...
Click to collapse
Take out the battery . Put the battery back in . Hold the power button & volume up button until you see your bootloader screen . Plug the phone into computer .download adb_fastboot from xda minimal install . Extract and install on C drive or desktop of computer . Inside folder right click and open a cmd window as administrator ..type
fastboot oem unlock
Volume up to select yes
fastboot flash recovery recovery.img
( Make sure you download one recovery img from my posts AND PUT IT INSIDE adb_fastboot tools folder )
fastboot reboot bootloader ( if it doesn't work do it manually)
Hold power & volume up key to enter bootloader screen
SCROLL WITH VOLUME KEY UNTIL YOU SEE OPTION WITH RECOVERY
SELECT WITH POWER button
when inside twrp flash rom , flash gapps , flash magisk ... or just flash magisk & noverity.zip from my posts .... * Obviously put all of these files on external sd
Or just use all-in-one-tool from my posts ...but most importantly
READ & STAY CALM AND THINK AND DON'T FORMAT good partitions bro :silly:
Most likely you can READ how to use power and volume up key to enter bootloader to enter recovery to flash noverity.zip ( that guide told you to put on external sd with magisk ) if you managed to flash recovery correctly ..before looping
Take out battery if you are back in loop . Put back try again ..even in a loop you can get to bootloader with holding power and volume up UNLESS you flashed a bad boot.img
THEN just take out battery and follow my threads that explain how to use SP flashrool to restore stock rom ..
Just install flashtool ..unzip stock rom..open flashtool ..click select scatter loading ..use navigation window popup to select scatter.txt in stock rom folder ..take battery out connect phone with usb..click download only button in sptool ..put battery in .. DON'T TOUCH ..WAIT FOR GREEN tick ..peace bro

i cant access bootloader with power button and volume down nothing happens wether its gone or i cant do it

madman141272 said:
i cant access bootloader with power button and volume down nothing happens wether its gone or i cant do it
Click to expand...
Click to collapse
Take out battery
Download & Install Motorola drivers
Download & Install latest SPflashtools
Download stock rom for flashtool
*You can find it in my posts*
PUT EVERYTHING ON DESKTOP
Connect your phone to computer without battery
Run flashtool as administrator
Unzip stock rom
In flashtool click select scatter
A navigation window will appear
Navigate to scatter.txt in unzipped stock rom folder
Click download only button in flashtool
Now put battery back
DON'T TOUCH IT
in bottom of flashtool different coloured progress bars will run
DON'T TOUCH
when a pop-up window with a tick appears
Unplug phone
Start phone with power button
YOU ARE BACK ON STOCK & NOT BRICKED
:fingers-crossed:
https://forum.xda-developers.com/moto-e4/development/moto-e4-woods-xt1762-build-nma26-42-75-t3688609
You will find all files you need in my thread in link

i dont get option in rsdlite to choose scatter.txt which is in my stock rom

madman141272 said:
i dont get option in rsdlite to choose scatter.txt which is in my stock rom
Click to expand...
Click to collapse
Rsdlite and flashtool are two different things . Please be more proactive if you really want to fix your phone. Did I say rsdlite at any point ?
---------- Post added at 04:39 PM ---------- Previous post was at 04:23 PM ----------
Here you go bro ... Please don't be so lazy bro ..
https://romprovider.com/2017/03/download-sp-flash-tools-all-version.html/
http://download1448.mediafire.com/3andp9nvcilg/45wpn5dcyz9wbmj/MOTOROLA_E_NMA26.42-75_ROW.7z

Download vcom driver first & install it && download flashtool && follow my instructions

Here you can see correct button in flashtool

boot
hi i get this when i do it
brom error s_security_secure_usb_dl_image_sign_header_not_found (6045) msp error code:0x00

madman141272 said:
hi i get this when i do it
brom error s_security_secure_usb_dl_image_sign_header_not_found (6045) msp error code:0x00
Click to expand...
Click to collapse
Don't select "cache" in the tick box window area then flash
If not work try "firmware upgrade" option
*If not make VIDEO so I can see what mistakes you are making* did you make sure you have correct files*

i cant make video as phone dont work but i put usb cable in click download then put battery in quick and bar goes red the purple then gett error when i remove cache

madman141272 said:
i cant make video as phone dont work but i put usb cable in click download then put battery in quick and bar goes red the purple then gett error when i remove cache
Click to expand...
Click to collapse
Ok unselect all the checkboxes . Then select only preloader and see if it flashes successful ly ..if it does tell me then I will tell you what to do next .

yes that worked what now

madman141272 said:
yes that worked what now
Click to expand...
Click to collapse
Don't remove your phone . Don't switch on . Start flashing ALL the files ONE BY ONE . USE DOWNLOAD ONLY SELECTION . When you see which file fails tell me which file is failing . You don't need to flash cache or userdata .
---------- Post added at 07:29 PM ---------- Previous post was at 07:24 PM ----------
Also note . MAKE SURE YOU ARE USING *LATEST* version of flashtool . Download a different version of flashtool too. Sometimes it gives 6045 error.
S_SECURITY_SECURE_USB_DL_IMAGE_SIGN_HEADER_NOT_FOUND (6045) , MSP ERROE CODE : 0x00
Meaning: The image files you are trying to flash doesn't contain the -sign header.
Solution:
Use SP Flash Tool V5.1532.00

what image should i use then

madman141272 said:
what image should i use then
Click to expand...
Click to collapse
I already answered that question. You don't even read my replies properly. The only thing left to do is for you to make an effort and read carefully and think , follow instructions and be a bit more autonomous. Peace bro . . I'm done.