Database Users

[Q] MY HTC WILDFIRE bricked

i rooted my mobile using alpharev and it turned my s-off and installed clockwork recovery mod 3.0.0.6 ,later i downloaded cynogen mod 7, and while updating it hung on now it is not at all booting it just shows htc in boot screev and reeboots again and again pls help me

Go back into recovery, wipe data and cache and the reflash CM7

Its definitely not bricked, so dont worry. Firstly, make sure you have wiped all data in Clockworkmod (Wipe Data / Factory Reset Option, Wipe Cache Partition also Format /system under Advanced). Once you have done this, try reflashing the CM7 ROM File. It should work. Reboot into Recovery by turning off your phone, pressing Vol Down + Power, Navigating to Recovery, and Pressing Power Button on it.
If it still fails, it would be better to use an updated version of Clockworkmod Recovery. This solved the bootloop issue for a few users.

3xeno said:
Its definitely not bricked, so dont worry. Firstly, make sure you have wiped all data in Clockworkmod (Wipe Data / Factory Reset Option, Wipe Cache Partition also Format /system under Advanced). Once you have done this, try reflashing the CM7 ROM File. It should work. Reboot into Recovery by turning off your phone, pressing Vol Down + Power, Navigating to Recovery, and Pressing Power Button on it.
If it still fails, it would be better to use an updated version of Clockworkmod Recovery. This solved the bootloop issue for a few users.
Click to expand...
Click to collapse
i tried it several times it says installing update and it again hangs pls help

3xeno said:
Its definitely not bricked, so dont worry. Firstly, make sure you have wiped all data in Clockworkmod (Wipe Data / Factory Reset Option, Wipe Cache Partition also Format /system under Advanced). Once you have done this, try reflashing the CM7 ROM File. It should work. Reboot into Recovery by turning off your phone, pressing Vol Down + Power, Navigating to Recovery, and Pressing Power Button on it.
If it still fails, it would be better to use an updated version of Clockworkmod Recovery. This solved the bootloop issue for a few users.
Click to expand...
Click to collapse
i tried it several times i removed my battery again booted to recoverymod wipe data/reset factory reset then install from sd card then i choosed the zib file .it then shows installing updating then it hangs pls pls pls help

i tried but it still hangs saying installing update and hangs on

Nivin Abraham said:
i tried but it still hangs saying installing update and hangs on
Click to expand...
Click to collapse
Please don't multi post. Update your Clockworkmod Recovery then. The guide can be found here:
http://forum.xda-developers.com/showthread.php?p=14693680

I had nothing but trouble using recorver 3.0.0.6 . Recovery 3.1.0.2 amd 2.5.07 have worked flawless for me though.

could u pls tell me how to update Clockworkmod Recovery , i downloaded ur file but i dont know how to update it

could u pls tell me how to update Clockworkmod Recovery

- First, Download the attachment in that thread, Place it somewhere, like on your C Drive, in a Folder called Fastboot.
- Then, Download the Updated Clockworkmod Recovery (Again linked in that thread). Extract the Recovery.img file from within the Zip file and place it in the Fastboot folder created in the step before.
- Connect your Wildfire to your PC. Turn it off, and turn on in HBoot Mode. (When your phone is switched off, then Press Vol Down + Power Simultaneously. Then, Navigate to Fastboot using the Volume Keys, and Press the Power Button. Your Wildfire is now in Fastboot Mode.
- Then, Open Command Prompt, and put in the following. (I am assuming your folder is created in C > Fastboot)
cd\
cd Fastboot
fastboot flash recovery recovery.img
(In the third step, I am assuming that the file name of the updated Clockworkmod Recovery is recovery.img) It will show two steps - Sending Recovery, and Writing Recovery. After this is done, your phone has the newer version of Clockworkmod Recovery and you can flash the ROM all over again and test.

3xeno said:
- First, Download the attachment in that thread, Place it somewhere, like on your C Drive, in a Folder called Fastboot.
- Then, Download the Updated Clockworkmod Recovery (Again linked in that thread). Extract the Recovery.img file from within the Zip file and place it in the Fastboot folder created in the step before.
- Connect your Wildfire to your PC. Turn it off, and turn on in HBoot Mode. (When your phone is switched off, then Press Vol Down + Power Simultaneously. Then, Navigate to Fastboot using the Volume Keys, and Press the Power Button. Your Wildfire is now in Fastboot Mode.
- Then, Open Command Prompt, and put in the following. (I am assuming your folder is created in C > Fastboot)
cd\
cd Fastboot
fastboot flash recovery recovery.img
(In the third step, I am assuming that the file name of the updated Clockworkmod Recovery is recovery.img) It will show two steps - Sending Recovery, and Writing Recovery. After this is done, your phone has the newer version of Clockworkmod Recovery and you can flash the ROM all over again and test.
Click to expand...
Click to collapse
pls dude dont get mad i am just frustrated dude i seriously dont know how to open command prompt. i did all the steps u asked me to do. i downloaded the file which u asked me to do i saved it in c/fast boot then extracted the file recovery-clockwork-3.2.0.0-j_r0dd_mod-buzz.img then i switched on my mobile in hboot mode then connected myusb cable to it, it showed hboot usb then i selected fastboot.
now it shows fastboot usb and these r the options given below
bootloader
reboot
reboot bootloader
power down
i seriously dont know how to open command prompt ur the only one who could help me so pls help me with all due respect

Nivin Abraham said:
pls dude dont get mad i am just frustrated dude i seriously dont know how to open command prompt. i did all the steps u asked me to do. i downloaded the file which u asked me to do i saved it in c/fast boot then extracted the file recovery-clockwork-3.2.0.0-j_r0dd_mod-buzz.img then i switched on my mobile in hboot mode then connected myusb cable to it, it showed hboot usb then i selected fastboot.
now it shows fastboot usb and these r the options given below
bootloader
reboot
reboot bootloader
power down
i seriously dont know how to open command prompt ur the only one who could help me so pls help me with all due respect
Click to expand...
Click to collapse
i downloaded only the updated clockworkmod recovery ,i dont know which (Download the attachment in that thread) i dont know which file ur asking me to download from that thread

Nivin Abraham said:
pls dude dont get mad i am just frustrated dude i seriously dont know how to open command prompt. i did all the steps u asked me to do. i downloaded the file which u asked me to do i saved it in c/fast boot then extracted the file recovery-clockwork-3.2.0.0-j_r0dd_mod-buzz.img then i switched on my mobile in hboot mode then connected myusb cable to it, it showed hboot usb then i selected fastboot.
now it shows fastboot usb and these r the options given below
bootloader
reboot
reboot bootloader
power down
i seriously dont know how to open command prompt ur the only one who could help me so pls help me with all due respect
Click to expand...
Click to collapse
Command Prompt is to be opened on your Windows PC. Not on your mobile. Once you have entered into Fastboot Mode and your Wildfire is connected to your PC, thats all you need to do.
Open Start Menu. Then Select Run. Then type "cmd" (Without Quotes) and Press Enter. This will open the Command Prompt. Then follow what I said before.
(Note - If your folders name is fast boot, then replace fastboot in the commands above with fast boot. It's basically the name of your folder).
Rename the IMG file you extracted to Recovery.img, it will typing the command easier.
Lastly, my only request to you - Make only 1 post at a time. Others here are normal members and not someone with the full day free . When you continuously post something, its frustrating to read and I dont feel like replying anymore to that person.

3xeno said:
Command Prompt is to be opened on your Windows PC. Not on your mobile. Once you have entered into Fastboot Mode and your Wildfire is connected to your PC, thats all you need to do.
Open Start Menu. Then Select Run. Then type "cmd" (Without Quotes) and Press Enter. This will open the Command Prompt. Then follow what I said before.
(Note - If your folders name is fast boot, then replace fastboot in the commands above with fast boot. It's basically the name of your folder).
Rename the IMG file you extracted to Recovery.img, it will typing the command easier.
Lastly, my only request to you - Make only 1 post at a time. Others here are normal members and not someone with the full day free . When you continuously post something, its frustrating to read and I dont feel like replying anymore to that person.
Click to expand...
Click to collapse
i opened command prompt and till the second step which u asked me to type was successfull
cd\
cd Fastboot
after this u asked me to type
fastboot flash recovery recovery.img
it says fastboot is not recognized as an internal or external command,operable program or batch file.
i dont know how to proceed further ,i am really sorry for multi posting i am new to xda dude , i am terribly sorry pls forgive me

You need to have HTC driver for doing that. Install this iin your windows PC.
Link: http://db.tt/BOJCbnD
Go with the process after installing this.
Sent from my HTC Wildfire using XDA App

Nivin Abraham said:
i opened command prompt and till the second step which u asked me to type was successfull
cd\
cd Fastboot
after this u asked me to type
fastboot flash recovery recovery.img
it says fastboot is not recognized as an internal or external command,operable program or batch file.
i dont know how to proceed further ,i am really sorry for multi posting i am new to xda dude , i am terribly sorry pls forgive me
Click to expand...
Click to collapse
Dont worry about it. That was just my view.
Anyway, I hope the folder creation was correct. I hope that when you extracted the Android Win Tools folder into your C:\Fastboot folder, you deleted the original folder?
ie:, In your Fastboot folder, you shouldnt have any other folder/sub folder, and it must contain only these 4 files:
- adb.exe
- AdbWinApi.dll
- AdbWinUsbApi.dll
- Fastboot.exe
Once you have ensured this, then make sure you enter Fastboot mode on your Wildfire Correctly.
- Start HBoot mode
- Then Plug in the USB Cable
- Press Power Button, then another set 4 Options will appear, the first being Fastboot
- Then Press Power Button again
After this, try running the commands in command prompt again. Let me know how it goes.

And it you still face any issues with fastboot flashing, then see my sign for the post link to complete guide. Go there and download attached pc49img.zip and put it on your root of memory card (formatted previously with fat32 partition) . Then reboot to hboot menu to update the recovery. That's all.
Sent from my HTC Wildfire using XDA App

bharatgaddameedi said:
And it you still face any issues with fastboot flashing, then see my sign for the post link to complete guide. Go there and download attached pc49img.zip and put it on your root of memory card (formatted previously with fat32 partition) . Then reboot to hboot menu to update the recovery. That's all.
Sent from my HTC Wildfire using XDA App
Click to expand...
Click to collapse
dude ur the man it worked i am so so so happy no words to express it showed
sending recovery
writing recovery

Nivin Abraham said:
dude ur the man it worked i am so so so happy no words to express it showed
sending recovery
writing recovery
Click to expand...
Click to collapse
Great, Hope they were followed by the words "OK". If so, you have the new Recovery 3.2.0.0 on your Wildfire.
Getting the hang of Fastboot is very important IMO. It helps flashing Recoveries in 1 go, and, also helps restoring Nandroid Restores, among many other features. I am glad you have experienced it, and, not gone the "PC49IMG" way.

[SOLVED]problem

i followed these instructions...
STEP 1: Installing LK Bootloader & Recovery
(If you have already installed a NAND version, you can skip the haret boot part, but it is very important to flash the new bootloader from lk-photonic-pc.rar!! It contains important changes for wifi calibration!)
1. Download all files for NAND (see downloads)
2. Extract lk-photonic-pc.rar to somewhere on your PC
3. Copy update-cm-7.2.0-RC0-photonic-KANG-signed.zip and the content of lk-photonic-sd.rar archive to the root of your sdcard and run HaRET from your device
4. The device should boot to the fastboot prompt. Connect the USB cable
5. If your connecting your phone for the first time to your pc you have to install drivers from the folder you have just extracted.(See also here) You can see it in your windows notification bar if you were sucessful. Be sure to have already run haret and already being in fastboot console on the device when installing drivers! If you are sill having problems to connect to the device via fastboot try installing HTC Sync (from htc website)
6. Enter the Fastboot-folder on your pc (the one you have extracted) and run bootloader.bat
7. The device should reboot now, when white "HTC" Bootscreen appears press "Volume down" and hold it until you have entered fastboot console again. If you have been too slow plug-out/in the battery and try again
8. Run recovery.bat on your host pc
9. Device should reboot again, now on HTC Bootscreen press and hold "Volume up" until you have entered CWM Recovery
[\quote] after stage 6 phone just freezes and then comes up with device unable to boot press vol up to reset device. it is on htc hd mini please help
Click to expand...
Click to collapse

et1990 said:
i followed these instructions...
STEP 1: Installing LK Bootloader & Recovery
(If you have already installed a NAND version, you can skip the haret boot part, but it is very important to flash the new bootloader from lk-photonic-pc.rar!! It contains important changes for wifi calibration!)
1. Download all files for NAND (see downloads)
2. Extract lk-photonic-pc.rar to somewhere on your PC
3. Copy update-cm-7.2.0-RC0-photonic-KANG-signed.zip and the content of lk-photonic-sd.rar archive to the root of your sdcard and run HaRET from your device
4. The device should boot to the fastboot prompt. Connect the USB cable
5. If your connecting your phone for the first time to your pc you have to install drivers from the folder you have just extracted.(See also here) You can see it in your windows notification bar if you were sucessful. Be sure to have already run haret and already being in fastboot console on the device when installing drivers! If you are sill having problems to connect to the device via fastboot try installing HTC Sync (from htc website)
6. Enter the Fastboot-folder on your pc (the one you have extracted) and run bootloader.bat
7. The device should reboot now, when white "HTC" Bootscreen appears press "Volume down" and hold it until you have entered fastboot console again. If you have been too slow plug-out/in the battery and try again
8. Run recovery.bat on your host pc
9. Device should reboot again, now on HTC Bootscreen press and hold "Volume up" until you have entered CWM Recovery
[\quote] after stage 6 phone just freezes and then comes up with device unable to boot press vol up to reset device. it is on htc hd mini please help
Click to expand...
Click to collapse
Try installing windowsce rom than try all from begining
Click to expand...
Click to collapse

how
how though it just freezes on htc screen

wooo sorted turns out i was tryin to install an o2 specific wince on my phone... bt my phone a vodafone phone tha has been unlocked to o2 lmao, installed voda update for wince rom then i managed to flash and install cyanogen 7 hehe works wonderfully thnx for all the help guys much appreciated

Honor 7 keeps booting into twrp.

Hi,
I have rooted my honor 7. All went well until I INSTALLED Quick Boot ( Reboot ) . I tried to see if I can get into recovery mode. The cell phone turned off came into recovery mode, but now I can not go out of recovery mode. Tried everything but mobile go back to recovery mode. Please help me.
Thanks in advance
Younus R.
Sorry if am i in wrong thread.

I don't know where the flag is set to tell the bootloader which mode to boot into. But I'd say this flag is probably stuck...
If you've tried all the options in TWRP's [Reboot] section (Reboot bootloader/system/recovery/poweroff) with no success, then your only option is to flash full stock

thnx for your reply. Problem solved
here is the solution
Step 1: Press Volume down - and Power Button For 10 seconds ( fastboot mode: ) while connect the USB cable from your device to your computer.
open the PC command line window, enter the ADB installation directory, make sure your phone and PC is connected,
Than type : fastboot devices
and than: type fastboot reboot
Thnx n hope this post will help other.
I Love XDA. thnx again:laugh::laugh::laugh::laugh:

How i can install Oxygen Os from adb fastboot on OnePlus 5 ?

Hi , on my Oneplus 5 i flash custom rom (twrp) and root my device , now i want delete all , i want return my OnePlus 5 at the same when i buy .
On the OnePlus one , i download a cyanogen fasboot rom , and in fastboot mode i put a command for erease all and install new recovery new system etc .
But on OnePlus 5 i not find this possibility , I can do this ? I can erease all and install a Oxygen from fastboot ? where I can find the fastboot rom and the command to put?
Solution
I solved my problem with this step.
1) Dowload OxygenOS rom from official site OnePlus http://downloads.oneplus.net/
3) Adb driver installed
4) Put the file of the oxygenOs in adb folder , you can see this folder in C:
5) Start the smartphone in recovery mode , now click install from adb
6) From windows positioning on C folder , and start new session of prompt from adb folder ( you can do this, click shift on keyboard and while right click on adb folder , and you can see the option start new prompt command from folder)
7) from the prompt you can put the command "adb devices" , for be sure the computer see your devices.
8) Now you can install your rom , put the command "adb sideload filename.zip"
Flashing stock recovery
1) Download stock Recovery OnePlus from here http://oxygenos.oneplus.net.s3.amazonaws.com/OP5_recovery.img or else you can see on the download site of oneplus
2) Copy the recovery in the adb folder
3) Start a new prompt command from the folder adb
4) Put the smartphone in fastboot mode (power off the smartphone , and click volume up + power)
5) Put the command "fastboot device" for be sure computer can see the smartphone
6) Put the command "fastboot flash recovery name-recovery.img"
I hope I can help other persons with the same problem

Flash stock recovery and install the latest full zip firmware.
Sent from my ONEPLUS A5000 using Tapatalk

omrij said:
Flash stock recovery and install the latest full zip firmware.
Sent from my ONEPLUS A5000 using Tapatalk
Click to expand...
Click to collapse
I install a stock recovery from fastboot , but when i prove to install a new incremental Ota of Oxygen Os this fails , so I wanted to delete everything and by fastboot install all from scratch.

simon3r said:
Hi , on my Oneplus 5 i flash custom rom (twrp) and root my device , now i want delete all , i want to return my OnePlus 5 at the same when i buy .
On the OnePlus one , i download a cyanogen fasboot rom , and in fastboot mode i put a command for erease all and install new recovery new system etc .
but on OnePlus 5 i not find this possibility , i can do this ? i can erease all and install a Oxygen from fastboot ? where i can find the fastboot rom , and the command to put?
Click to expand...
Click to collapse
Doesn't work for me the original recovery won't recognize adb device so here i have done this:
1) Flash a custom rom Oos based via twrp (i've done this with freedomos) DO NOT REBOOT phone after flash
2) Flash original OxygenOs firmware provided by oneplus site DO NOT REBOOT phone, not yet
3) Put original recovery in your sd card from your pc via twrp (if you don't already have it)
4) Install original recovery from twrp
5) After that, reboot to recovery and you should have the op original one, perform a factory reset via recovery
6) try starting device, if everything works you can finally re-lock bootloader (only if you want)

Solution
Thank you all for reply , i solved my problem with this step.
1) Dowload OxygenOS rom from official site OnePlus http://downloads.oneplus.net/
3) Adb driver installed
4) Put the file of the oxygenOs in adb folder , you can see this folder in C:
5) Start the smartphone in recovery mode , now click install from adb
6) From windows positioning on C folder , and start new session of prompt from adb folder ( you can do this, click shift on keyboard and while right click on adb folder , and you can see the option start new prompt command from folder)
7) from the prompt you can put the command "adb devices" , for be sure the computer see your devices.
8) Now you can install your rom , put the command "adb sideload filename.zip"
Flashing stock recovery
1) Download stock Recovery OnePlus from here http://oxygenos.oneplus.net.s3.amazonaws.com/OP5_recovery.img or else you can see on the download site of oneplus
2) Copy the recovery in the adb folder
3) Start a new prompt command from the folder adb
4) Put the smartphone in fastboot mode (power off the smartphone , and click volume up + power)
5) Put the command "fastboot device" for be sure computer can see the smartphone
6) Put the command fastboot "flash recovery name-recovery.img"
I hope i can help other person with my problem

simon3r said:
Thank you all for reply , i solved my problem with this step.
1) Dowload OxygenOS rom from official site OnePlus http://downloads.oneplus.net/
3) Adb driver installed
4) Put the file of the oxygenOs in adb folder , you can see this folder in C:
5) Start the smartphone in recovery mode , now click install from adb
6) From windows positioning on C folder , and start new session of prompt from adb folder ( you can do this, click shift on keyboard and while right click on adb folder , and you can see the option start new prompt command from folder)
7) from the prompt you can put the command "adb devices" , for be sure the computer see your devices.
8) Now you can install your rom , put the command "adb sideload filename.zip"
Flashing stock recovery
1) Download stock Recovery OnePlus from here http://oxygenos.oneplus.net.s3.amazonaws.com/OP5_recovery.img or else you can see on the download site of oneplus
2) Copy the recovery in the adb folder
3) Start a new prompt command from the folder adb
4) Put the smartphone in fastboot mode (power off the smartphone , and click volume up + power)
5) Put the command "fastboot device" for be sure computer can see the smartphone
6) Put the command fastboot "flash recovery name-recovery.img"
I hope i can help other person with my problem
Click to expand...
Click to collapse
Yes this is the "defualt" method.. Mine was in case your PC won't recognize adb in stock recovery, because it happened at too many people for what i've seen on oneplus 3/3t/5

simon3r said:
Thank you all for reply , i solved my problem with this step.
1) Dowload OxygenOS rom from official site OnePlus http://downloads.oneplus.net/
3) Adb driver installed
4) Put the file of the oxygenOs in adb folder , you can see this folder in C:
5) Start the smartphone in recovery mode , now click install from adb
6) From windows positioning on C folder , and start new session of prompt from adb folder ( you can do this, click shift on keyboard and while right click on adb folder , and you can see the option start new prompt command from folder)
7) from the prompt you can put the command "adb devices" , for be sure the computer see your devices.
8) Now you can install your rom , put the command "adb sideload filename.zip"
Flashing stock recovery
1) Download stock Recovery OnePlus from here http://oxygenos.oneplus.net.s3.amazonaws.com/OP5_recovery.img or else you can see on the download site of oneplus
2) Copy the recovery in the adb folder
3) Start a new prompt command from the folder adb
4) Put the smartphone in fastboot mode (power off the smartphone , and click volume up + power)
5) Put the command "fastboot device" for be sure computer can see the smartphone
6) Put the command fastboot "flash recovery name-recovery.img"
I hope i can help other person with my problem
Click to expand...
Click to collapse
This definitely will help me recover my semi-bricked device, with twrp not accepting modifications or even read/Write internal memory, flashed oreo rom it wiped out my internal memory and now stucked completely to that rom. Hopefully i will get back to factory os with this method Thanks in advance bro helpful people like you keeping this community alive!

simon3r said:
Thank you all for reply , i solved my problem with this step.
1) Dowload OxygenOS rom from official site OnePlus http://downloads.oneplus.net/
3) Adb driver installed
4) Put the file of the oxygenOs in adb folder , you can see this folder in C:
5) Start the smartphone in recovery mode , now click install from adb
6) From windows positioning on C folder , and start new session of prompt from adb folder ( you can do this, click shift on keyboard and while right click on adb folder , and you can see the option start new prompt command from folder)
7) from the prompt you can put the command "adb devices" , for be sure the computer see your devices.
8) Now you can install your rom , put the command "adb sideload filename.zip"
Flashing stock recovery
1) Download stock Recovery OnePlus from here http://oxygenos.oneplus.net.s3.amazonaws.com/OP5_recovery.img or else you can see on the download site of oneplus
2) Copy the recovery in the adb folder
3) Start a new prompt command from the folder adb
4) Put the smartphone in fastboot mode (power off the smartphone , and click volume up + power)
5) Put the command "fastboot device" for be sure computer can see the smartphone
6) Put the command fastboot "flash recovery name-recovery.img"
I hope i can help other person with my problem
Click to expand...
Click to collapse
Awesome, works

Thank you for valuable guidance . I found this explanation only You and another perso
Thank you for valuable guidance . I found this explanation only You and another person how to get back with oreo on runoff

Worked Perfectly for me!! really helphul
:laugh::laugh::good:
simon3r said:
Thank you all for reply , i solved my problem with this step.
1) Dowload OxygenOS rom from official site OnePlus http://downloads.oneplus.net/
3) Adb driver installed
4) Put the file of the oxygenOs in adb folder , you can see this folder in C:
5) Start the smartphone in recovery mode , now click install from adb
6) From windows positioning on C folder , and start new session of prompt from adb folder ( you can do this, click shift on keyboard and while right click on adb folder , and you can see the option start new prompt command from folder)
7) from the prompt you can put the command "adb devices" , for be sure the computer see your devices.
8) Now you can install your rom , put the command "adb sideload filename.zip"
Flashing stock recovery
1) Download stock Recovery OnePlus from here http://oxygenos.oneplus.net.s3.amazonaws.com/OP5_recovery.img or else you can see on the download site of oneplus
2) Copy the recovery in the adb folder
3) Start a new prompt command from the folder adb
4) Put the smartphone in fastboot mode (power off the smartphone , and click volume up + power)
5) Put the command "fastboot device" for be sure computer can see the smartphone
6) Put the command fastboot "flash recovery name-recovery.img"
I hope i can help other person with my problem
Click to expand...
Click to collapse

Help! I tried to do the sideload but in my powershell window says "loading: 'update.zip' *cannot read 'update.zip'* " I don't know what's the problem, my computer can detect my phone with "adb devices" and "fasboot devices" so that's not the problem

Reason for that is adb on Windows can't read large files as it's not Large Address Aware, I'll get the article I use that has a tool that enables that when I get home, it's basically a small program you need to run that enables that functionality.

Fosko Stock said:
Help! I tried to do the sideload but in my powershell window says "loading: 'update.zip' *cannot read 'update.zip'* " I don't know what's the problem, my computer can detect my phone with "adb devices" and "fasboot devices" so that's not the problem
Click to expand...
Click to collapse
use This Software to solve Large address Aware problem
w.techpowerup.com/forums/threads/large-address-aware.112556
it worked for me
Please Select the adb Software correctly as it got me Confused I have installed 2-3 Of them

love you

[Z00ED]Can't install twrp .img in order to root

Hi There.
Maybe a newbie problèm but in order to unlock bootloader and Root my device, can't install the twrp.img file on cmd i can reboot on fastboot mode but fastboot boot twrp-......IMG still getting me no such a file...
I've checked and reinstalled drivers by autorised unsigned drivers,when i look on my Android adb device all seems good..
Any ideas?

Fastboot boot twrp.img enter see your phone load in to twrp mode .. then restart using twrp . After boot . Agin go fastboot mode and type fastboot flash recovery twrp .img (u can drag this file also if u want or manualy typing as u wish) . Enter and wait few sec. Its finish. Then type fastboot reboot (remembar before hiting entar tap volume down switch then hit entar). Now u feel viberet and see twrp logo . Then go wipe advanced wipe tik the ASDF swipe to conform. And then restart ur phone.... congarts u have succesfully install twrp ... enjoy .

THX it s more clear i ll try and let u know

First of all download the app TWRP from play store . Then download the latest version of twrp from there .
Then you have to unlock your bootloader by using the app unlock device tool . After unlocking the bootloader go to developer option and enable USB debugging . After that connect your laptop or PC to your mobile . An option will come on your screen to allow debugging to the device . Allow it permanently . Then open adb (I hope you have installed it otherwise download and install it Just google it download adb ) After installing open C drive and then go to adb . Then open command prompt there by pressing cntrl shift and right click . there will be an option to open command prompt there . After opening just type adb devices there in the command prompt it will show your device serial no. Then move the twrp file from your mobile to PC and to adb folder . Then rename it to recovery .
Then switch off your mobile and open fastboot mode by pressing power button and volume up button . then go to the command prompt you have opened before . type there fastboot devices . it will show your device serial no. Then type Fastboot flash recovery recovery. Img then wait for some time after the processing gets over in there . then switch off the mobile by removing battery and switch on to recovery mode by pressing power button and volume down button . Congrats twrp has been installed successfully in your device . You will see twrp window. If this works then thumbs up