i need you opinions frainds - HD Mini General

Hi men:
after i had tried a rom by PC, my HD mini stoped on HTC image on its screen after finishing the download and never complete the Restarting
i have tried download the rom by SD card with many different rom....but the device shown "load" word on screen and it never complete the operation....
i need your help please
sorry for my bad English...apologize me old chaps

try to remove the battery, put it back, start in bootloader (keep volume down pressed while pressing power), and then try to flash your factory shipped rom.
You can try with a custom rom, using sspl, if you don't know what factory shipped rom you have. But it doesn't work for sure.
As Cotulla says,
Worst case is that you destroy your OS partition, in that case you must flash a ship ROM using the original SPL (Vol down on boot run ruu from PC )
Click to expand...
Click to collapse
Try the indication here: http://forum.xda-developers.com/showthread.php?t=694409
If it don't work, you have to find your shipped rom and try with it.

thank you
i'll try that and..... i'll tell you what i found then
second time thank you

Related

[HELP] Unable to boot into Windows

After I have installed the maatiROM.V3 ROM, my phone has not been able to boot into Windows properly.
It booted into Windows the first time after I installed the ROM, however, when I tried to restore the programs and reset the device, it tries to install the ROM automatically again, however, after its all done and reset, it holds on a white screen with the HTC logo.
Can someone please give me some advice?
Download youre Original rom for youre device. and get the Leo in 3 colour screen then connect the usb and flash the Original rom back.. than it must work.
Jowan073db said:
Download youre Original rom for youre device. and get the Leo in 3 colour screen then connect the usb and flash the Original rom back.. than it must work.
Click to expand...
Click to collapse
my original version is 1.48.831.0 (71294) WWE
but I couldn't find it
I have version RUU_Leo_HKCSL_CHT_1.48.832.1_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
but I dont know I need to use SSPL to install it or not....
I try to use SSPL to install it, but error [294] occur.....
WHAT CAN I DO???
thanks!!
kayzee said:
my original version is 1.48.831.0 (71294) WWE
but I couldn't find it
I have version RUU_Leo_HKCSL_CHT_1.48.832.1_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
but I dont know I need to use SSPL to install it or not....
I try to use SSPL to install it, but error [294] occur.....
WHAT CAN I DO???
thanks!!
Click to expand...
Click to collapse
Just download it from HTC support site... no need to use SSPL for this as it is the original ROM...
kurniawan77 said:
Just download it from HTC support site... no need to use SSPL for this as it is the original ROM...
Click to expand...
Click to collapse
I am come from Hong Kong
Hong Kong's HTC website no download link.....
I dont know which version should I install
I got two version now
one is Official WM6.5 ROM - HTC HD2 (Leo) - English Asian Version(1.48.707.2)
the other is Leo_HKCSL_CHT_1.48.832.1-this is a chinese version which released by CSL (CSL is the provider which sell the phone to me, but my original rom is 1.48.831.0 (71294) WWE(English))
so I am very confuse now...
dont know which one is suitable....
Any idea??
thanks thanks thanks thanks so so much!!
I tried to install both official english and CSL chinese version, its show error [294].......
What should I do??????
now, the phone can get into windows(maatiROM.V3 ROM),but the phone keeping crash...and I reset it....the phone will re-install the windows(maatiROM.V3 ROM) again.... then crash again, and I reset again, and the phone re-install again.....keeping repeat crash, and I reset it, and re-install windows.......
*CRYING*
I dont know what can I do now.........
In my opinion you can try the folowing:
- Remove sim and memory card and do a hard reset (with phone off , keep holding down the volume up and volume down keys and press power button, release all butons then press volume up again to restore manufacrurer deaults)
- Try to enter in boot mode (with phone off , keep holding the volume down and press power button) then flah again your phone
- If none of these helps and you can't find the original rom then use the GOLDCARD method. So make yourself a goldcard (serch the forum and you will find how to do that), boot your phone into flash mode with goldcard inside and you will be able to flash any original rom to your device
WBR
golumbu
golumbu said:
In my opinion you can try the folowing:
- Remove sim and memory card and do a hard reset (with phone off , keep holding down the volume up and volume down keys and press power button, release all butons then press volume up again to restore manufacrurer deaults)
- Try to enter in boot mode (with phone off , keep holding the volume down and press power button) then flah again your phone
- If none of these helps and you can't find the original rom then use the GOLDCARD method. So make yourself a goldcard (serch the forum and you will find how to do that), boot your phone into flash mode with goldcard inside and you will be able to flash any original rom to your device
WBR
golumbu
Click to expand...
Click to collapse
Thanks!!!I restored the phone to manufacurer default!Seems to be ok!!
thanks so much!!!
I
kayzee said:
Thanks!!!I restored the phone to manufacurer default!Seems to be ok!!
thanks so much!!!
I
Click to expand...
Click to collapse
It happened to me and I found out it is one of the reg tweaks in combination of a cab I installed did not work with maatiROM. The rom itself is stable and I use the Premium, which version did you use?
sakiin said:
It happened to me and I found out it is one of the reg tweaks in combination of a cab I installed did not work with maatiROM. The rom itself is stable and I use the Premium, which version did you use?
Click to expand...
Click to collapse
same as you!!!
I am using premium.....

Bricked via HSPL?

Hey all,
Just a little background information:
- Hard SPL'd my phone to flash Dutty's cooked ROM.
- All of a sudden one day, the phone switched off. I tried to boot it up but it will freeze on the HTC loading screen where it displays the radio version, ROM version in red down the bottom - the phone would not go any further.
- My computer won't even recognise it when I plug in my USB.
Anyway, I figured I'd try to uninstall HSPL and start over again. I downloaded an official HTC ROM, tried to load into the bootloader and now I'm stuck.
The screen reads:
Upgrade ROM code error
Please try again
If I pull out the battery/SD card, it will load into this screen again.
What *I THINK* may be the issue is that I didn't use the original ROM SPECIFIC to my phone, i.e. WWE Asian ROM.
I've updated the ROM image on my SD card but I can't get into the original bootloader to start the uninstallation process again.
Help!
Ok, nice and calm, are you sure you can't get into bootloader mode?
Power off, sim and sd card out (just to be sure)
hold volume down, tap power, continue to hold volume down.
samsamuel said:
Ok, nice and calm, are you sure you can't get into bootloader mode?
Power off, sim and sd card out (just to be sure)
hold volume down, tap power, continue to hold volume down.
Click to expand...
Click to collapse
I can get into the bootloader just fine.
It will display the error message and I can't do anything.
OK, so if you can get to the 3 coloured screen, you can just flash HSPL (if it isn't still installed) and flash a new rom.
Boot to bootloader(3 coloured screen), connect to computer, run HSPL.exe
samsamuel said:
OK, so if you can get to the 3 coloured screen, you can just flash HSPL (if it isn't still installed) and flash a new rom.
Boot to bootloader(3 coloured screen), connect to computer, run HSPL.exe
Click to expand...
Click to collapse
My computer refuses to connect to the phone.
I'll plug in my USB cable, windows will make the connection sound but the phone won't load into Windows Explorer.
What does it say by the spl? 1.42.0000? or 1.42.HSPL?
Actually it doesnt matter, when you hear the connection sound, thats enough, Run HSPL.exe, and if its not already installed, it should install, if it is already installed it will say 'hspl requires 1.42.000' or something.
Either way, you can then go ahead and flash a new rom.
samsamuel said:
Actually it doesnt matter, when you hear the connection sound, thats enough, Run HSPL.exe, and if its not already installed, it should install, if it is already installed it will say 'hspl requires 1.42.000' or something.
Either way, you can then go ahead and flash a new rom.
Click to expand...
Click to collapse
No, it doesn't work.
When I run HSPL.exe, it says it can't find my phone.
I already have HSPL installed with a custom ROM.
The phone is stuffed whereby I couldn't get past the HTC logo screen - it just freezes there.
I tried uninstalling HSPL thinking this would solve my problem with no luck.
The phone boots into the bootloader with an error message that I can't seem to get around.
Ah ok, so you get the error message on the 3 coloured screen? If that is the case, then spl itself is corrupt.
I thought you got the error message when the phone tried to boot, my mistake.
Next to try then is to find the original rom that came on your phone, and flash it from sd card, and hopefully it will overwrite the spl. It must be the correct rom for your provider and region, though.
If that doesn't work, then i'm afraid all I can do is wish you best of luck.
samsamuel said:
It must be the correct rom for your provider and region, though.
Click to expand...
Click to collapse
I think this is where I went wrong.
I tried uninstalling HSPL with a ROM that wasn't from my region which is why I'm getting these errors.
Surely there's a way around this?
If you can find your original rom, there is a good chance you will be fine, OR you can probably try the goldcard route, however i'm not 100% so i wouldnt go handing over cash (goldcard isn't free) until you are sure.
Do you know what rom you are looking for?
samsamuel said:
If you can find your original rom, there is a good chance you will be fine, OR you can probably try the goldcard route, however i'm not 100% so i wouldnt go handing over cash (goldcard isn't free) until you are sure.
Do you know what rom you are looking for?
Click to expand...
Click to collapse
I'm sure my phone's original rom was the WWE Asian version from Hong Kong.
I've uploaded the ROM onto my SD card but I can't get the bootloader to load it.
As stated before, I used another ROM at first and then it crashed on me.
Everytime I start the bootloader, it won't let me load the Asian ROM from scratch.
It just displays the error with no way around it.
Hmm, ok, just a couple of last thoughts then i gotta go to bed.
1 - sd card formatted fat32
2 - some people have better luck with 2gb cards than with bigger ones.
3 - Was the phone bought direct unlocked from HTC or is there a chance its provider locked? (i.e are you REALLY SURE you have the right rom)
4 - RUU_Signed.nbh coppied to sd card and renamed leoimg.nbh
Gotta go, best of luck.
ok. u are getting error in bootloader? what exacly is the error message you are getting..
Hard Reset
I had a similar problem to this and a hard reset solved the problem. Did you try a hard reset? I think its press volume up and volume down and power simultaneously.
DownloadMaster said:
I had a similar problem to this and a hard reset solved the problem. Did you try a hard reset? I think its press volume up and volume down and power simultaneously.
Click to expand...
Click to collapse
Even that won't work!
Confirmed hard reset but pressing "Volume Up", then the screen blacks out immediately and nothing happens.
When I press the "power on" button, all I see is an exclamation mark for a second then a black screen.
I think the solution is for you to try flashing to HSPL again.
1. Boot to bootloader mode by pressing Vol down key and click the Power button. You should get the tri colour screen, and the word "Serial" on the bottom.
2. Plug in the USB cable to your PC. The word "Serial" should then change to "USB".
3. Run hspl.exe as administrator.
I did the same as you previously when I tried to load the SEA 1.66 ROM on my Hong Kong English phone, and recovered it by using the above steps. I had to run HSPL 3 times before it worked. The first 2 times, it would seem to work as I'd get the "We Hacked it!" message, but when I rebooted the phone to the bootloader, it still wasn't HSPL. Only on the 3rd try, did it successfully load HSPL to the bootloader.
-edit-
You can download the original Hong Kong CSL ROM from a link in this thread.
got to say, if in doubt - goldcard it!!!
what is your spl version now? 1.42.0000 or 1.42.hspl '?
only bootloader is never a problem with hspl installed.
only bootloader is no problem with original spl version as long as you have a compatible stock rom.
\I wonder whether the phone would connect to computer properly.
After plenty of reading around, I've finally fixed the issue!
It was the easiest of all fixes - all I had to do was to download the original factory ROM the phone came with (.exe file) and run the executable with the phone plugged in via USB.
Thanks to all those who have tried to help.

[HELP] HTC HD2 cant boot after hard reset or hard reset failed

hi guys..
please help me .. i flash my HTC HD2 with a MAGDLR111 and after it doesnt continue to boot and only stock in boot image. i try to use Hard Reset (holding down the up and down botton and tapping the power button), it response very quick but it says the "restore completed and press up botton to reboot" and so i did but still, it still stock up in boot image forever.. please help me, what should i do..thanks
Possibly a radio problem. Boot pressing volume down button to get into bootloader and flash a radio WITHOUT .51. in its name....
Sent from my Nexus One using XDA App
thanks, already did... and it works.. )))
hey i have that same problem now can you help me get a radio so i can download it or can even help me through the steps to get back my phone to normal plzzz.? thank you
Any new user most definitely has a lot of questions...
Here is a thread you should carefully check - it explains some basic stuff, and it offers links to many other specific threads, incl. Radio ROM.
To return to "normal" ROM, please just check the standard flashing process. You can flash via USB or SD card, whatever ROM you like, stock or custom.
Hey man thanks for all that but i really don't want just any rom, i wanna know if anyone can get me the rom that comes with the phone for windows mobile 6.5, you know with the orange load screen etc, i really dummy in this thing and i should not of even played fast to go try flashing my HTC HD2 with a MAGDLR111.
so i've tried various roms and everyone of them was going great unitl step 2 in the upgrade process, it kept saying error filr open, check update rom utility. where do i go from here?
It is quite difficult to help if there is so little basic information available.
The error you mention can have a simple reason. Usually, the ROM image file name is simply not correct.
To flash via USB:
There are 2 options:
First, you can take an original RUU of your network operator (in case you have a branded phone) or HTC, put the phone into boot loader mode (see below), start the RUU.exe on your PC.
Second, you can extract the original RUU.exe with WinRar or a similar program, take the .nbh file and rename it to leoimg.nbh.
Once you take an image of the ROM, you have to put it into the very same folder where your ROM update software is (LeoCustomRUU, SSPL, whatever). One more time, please check the suffix, it should be .nbh, as in "leoimg.nbh".
Keep in mind: Do start the RUU software as "Admin" - whichever you choose.
Instead of the original ROM, you can flash custom ROMs, too - since your device must have HSPL installed when you used WP7 or Android before.
If you´ve got issues (because of Win 7 on your PC or such), please try to put your device into bootloader mode before connectint it to the PC (turn off the device, push vol. down and power at the same time, the multi color bootscreen should appear, only now connect it to the PC).
To flash via SD card:
Re-format your SD card FAT32. Don´t put anything else on it. Copy the ROM image file with the exact naming as above on the SD card.
To start the flash process, do the same as above, go into bootloader mode, the flash process will start - just follow the on-screen instructions.
i have this same problem only it happened without me flashing anything or something like that. i dont have custom rom or hspl. everything is stock. what should i do?
bump ^^
The message you have entered is too short. Please lengthen your message to at least 10 characters.

[Q] Hellllllllllllllllllllllllllllllllllllllllllllllll lllp

I was trying to install blackSTONEhengeHyPerSlim_4_1 on my blackstone. I installed olinex and after that stored the nbh and exe file on the sd card and then through task 29 flashed it. The rom got successfully installed but now the phone is stuck at the bootup. It says
Checking Radio...
Checking protocol..
Checking Rom..
But now won't get to the next screen.Because of this i can't get to active sync. Please help..Pleaaaasseee
Did u follow the instructions completely, cause it worked fine for me and others... Do you have radio 1.14 or above installed? Did u try to reflash?
ok, no need to worry. Boot into bootloader. What is your SPL?
Yes i did follow the instructions. Now the phone won't bootup. I tried it with the volume down and power up method. Rom does get installed but then again it won't bootup..
Did you try Vol UP + Vol Down + Power ?
Yes i did try that after my phone got screwed up with test29 method but it shows nothing at all after successfully installing rom..:-s
no need to worry
always read read read and must read before flashing. I think your phone is quite ok. You does task29 to it. what is task 29 means. it means task29 will clean our device completely only splash screen displyaed, phone always stucked on this screen. it is very normal, it means you completyely cleaned your device. now you are ready to flash your device. do the following procedure--
1. remove the battery and reinsert it.
2. now turn on the phone while pushing volume down key.
then bootloader (tricolor screen) mode will be displayed. many times it will not come into bootloader and device normally starts and stuck on splash screen. the reason is simple, you didnt press volume down key properly, it happend many times to me also.
Now remove battery cover, remove battery and reinsert it, dont cover the battery, now take slylus & press volume down strip with the stylus. ( volume up & down keys are installed in battery cover, so when you push volume down key in flap open condition, it should be done by stylus.)
ok
push volume down by stylus & hold it and start the device, it will come in tricolor screen means bootloader mode, on the bottom screen it will show serial.
Now conect the device to the pc & bottom line on the screen will become serial to USB.
Now perform task28= means flash normal rom, do not perform task 29 again.
task29 will take 1 minute to flash while normal RUU will take about 7-8 minute.
try it and give feedback/
kulwant said:
Yes i did follow the instructions. Now the phone won't bootup. I tried it with the volume down and power up method. Rom does get installed but then again it won't bootup..
Click to expand...
Click to collapse
Have you flashsed a differnet radio ?
What you did is just Task29 your phone. Task29 needs something to flash in order to do its thing. Usually we flash radios (good ones obviously) because they are smaller than full roms. If you flash a full rom with Flash29, it will get erased after completion.
What you need to do now (since your phone now has no ROM installed) is boot it while pressing volume down to get to the bootloader, plug via USB and flash a rom using a "non-task29" flasher, like the standard BlackStoneCustomRUU.exe file that comes with basically every rom.
Hello thanks for replying my internet wasn't working but i did manage to boot my phone but now the touch stops working after. I know this as i press the volume button and the phone responds to that hence telling me it's not really freezed up. This is all what i did.
Stored .nbh file in the task 29 folder this is the rom version whose nbh file is used (RUU_Duttys_HD_V3.9__XT_Turbo_5.2.21051.1.6.4_1.59.709.0_Radio_52.62.25.34_1.14.25.24_)
After the flashing is done i reset the phone by taking out battery and starting it again in bootloader.
Now i flashed again with (blackSTONEhengeHyPerSlim_4_1)
After installing it completely the touch stops responding.
Kindly help me with what seems to be the problem. Thanks
kulwant said:
Hello thanks for replying my internet wasn't working but i did manage to boot my phone but now the touch stops working after. I know this as i press the volume button and the phone responds to that hence telling me it's not really freezed up. This is all what i did.
Stored .nbh file in the task 29 folder this is the rom version whose nbh file is used (RUU_Duttys_HD_V3.9__XT_Turbo_5.2.21051.1.6.4_1.59.709.0_Radio_52.62.25.34_1.14.25.24_)
After the flashing is done i reset the phone by taking out battery and starting it again in bootloader.
Now i flashed again with (blackSTONEhengeHyPerSlim_4_1)
After installing it completely the touch stops responding.
Kindly help me with what seems to be the problem. Thanks
Click to expand...
Click to collapse
Hi mate.
I did somthing for you....so i hope it will helps you.
1. download file from this link. http://hotfile.com/dl/115059516/5623431/Radio_1.13.xx(original_hd_nbh)__task29.rar.html and after unrar.
2. Make task 29 with this one. (Nothing change in that unrar folder)
3. After finished T29, take uot battery, put it back, put device to BootLoad. screen.
4. Connect with PC again and flash your desided ROM. (it means if you choice your rom, after unrar or unzip, Rom has own folder with that all files ...BLACIMG.nbh, BS_CustomRUU.exe, etc......
thanks i'll just download and do it..Will definitely post in what happened...Thanks a tonne for the quick response..
kulwant said:
thanks i'll just download and do it..Will definitely post in what happened...Thanks a tonne for the quick response..
Click to expand...
Click to collapse
...It's ok mate, like i wrote, i hohe, it 'll helps you.
let me know after....
Any new good looking rom you would suggest for me to try that would be bugfree ???
kulwant said:
Any new good looking rom you would suggest for me to try that would be bugfree ???
Click to expand...
Click to collapse
.... for beginning: T29 finished ok?
for your guestion: Hmmmm, for me...really good ROM is from Cloudyfa, but objectively, it's up to you, which one from this site you choice.
The link you gave me says
This file is either removed due to copyright claim or is deleted by the uploader.
:-s
kulwant said:
The link you gave me says
This file is either removed due to copyright claim or is deleted by the uploader.
:-s
Click to expand...
Click to collapse
Yeas mate, i deleted it. I was thinking, that you download this file already and saved it to your PC.
LoL it's all cool it takes a while i got 512kbps..I got the stock rom from xda page
RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship.exe
This one's fine right
kulwant said:
LoL it's all cool it takes a while i got 512kbps..I got the stock rom from xda page
RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship.exe
This one's fine right
Click to expand...
Click to collapse
Yes that one is fine. Once T29 is complete take out battery and then re-insert it. Now put phone into bootloader (hold vol down and press power on while still holding vol down. BOOTLOADER IS A TRI-COLOUR SCREEN).
Now flash your rom
i also flashed blackstonhenge hyperslim 4.6 and now touchscreen stopped working....any solution...

my htc hd2 is STUCK.. HELP ME PLS

I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Before we start, you can ask him how his device has ended up like this, can't you?
boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
Click to expand...
Click to collapse
Sir, you have forgotten your caps locked.
boxboy said:
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
Click to expand...
Click to collapse
Because you have stock SPL, you won't be able to install any custom ROM or any stock ROM not made for your region/SN.
boxboy said:
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
Click to expand...
Click to collapse
AFAIK, task29 is, also to be considered, a custom rom so it needs HSPL to be flashed. Are you sure you have followed the steps correctly?
boxboy said:
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
Click to expand...
Click to collapse
That is not a ROM, it's a radio. You need to flash HSPL to be able to change the splash screen (NRG Screen). HSPL should go like this: SPL 2.08.HSPL .
boxboy said:
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Microsoft is a corporation, Windows Phone is the OS .
One more thing, to be able to flash a LEOIMG from sd, the .nbh must be a rom that is compatible with your device (It will work if you get it from htc.com using the device's serial number)
I hope this helps. And I'm sorry if I am incorrect at something.
Good luck.
------------------------------------------------------------------------------------------------------------------------------------------------
To summarize it, you need to do either one of the following:
1- Install HSPL, and do what you want.
2- Go to HTC.com, download a rom using your Serial Number, rename file to .zip, extract the .nbh file, rename to LEOIMG.NBH [Capital letters], put onto sd card and insert into phone, boot up device while holding volume down ONLY, and make sure splash is removed and you're back to the "htc" stock, then send to repair [why?].
posting teh same post in multiple sub forums is considered rude
http://forum.xda-developers.com/showthread.php?t=1440265
Yeah, HSPL is needed for flashing pretty much everything. One thing you could do would be to flash a stock ROM from your SD card (just google it I CBA to provide links and stuff) which would reset everything to factory WinMo (including SPL to SPL3.03 [assuming you flash the latest ROM 3.14]) and from here it would basically be a fresh start. Probably the safest route without HSPL
Hi.
Thank you for your replies...
Let me tell u guys if I forgot to say earlier. The mobile phone is not letting flash any of the Hspl... be q series, 2 series or 3.series... all the times it says error 0000006 and 000000010 etc... a couple out of hundreds it did let flash but then it doesn't let me flash the factory rom fom HTC.
I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck
OK,
My final.outcome.
This phone let's me flash the hspl but it doesn't let me flush any roms including the original HTC factory rom.
I can also perform the task 29. Etc but still the NRG screen is still there.
I would like to know that if I flash the original Split and send it HTC, will be repairable for free? Sure? Even with the NRG.
now i think the only option available to you is jtagging the device which may permanently void the warranty !!
it had happened with me once, but somehow it got solved !
i used to randomly install clk, magldr, radios, hspl etc multiple times !
it used to get stuck while installing and then i used to remove the battery and try again !!
somehow it started ! !!
STRANGE DEVICE !!
Yeap its a real problem!!
Now , It will not let me change the hspl to spl whatsoever I do.
I would like your suggestions
I bought this brick for £50 and I can return it to get my money back. Has any used jtagging and does it 100% work?. The thing is if I do used jtagging, and if it doesn't work ,then I can,t return it!. How much does it cost and is it worth it?
jtagging will solve your problem !!
they remove the motherboard of the device and flash the os into the motherboard directly through a device named riff box !!
refer this video for more info !!
http://www.youtube.com/watch?v=zElsUERTzOU
but pls do not try this at home ! !!
just contact a local repair shop to jtag your device !!
also u can contact these guys from the video !!
good luck ! !!
boxboy said:
I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck
Click to expand...
Click to collapse
Check that the micro USB connection isn't "wobbly".
I had a TMOUS HD2 and never had any issues. Then, I sold it and got a Telstra HD2 and had big issues getting ROMs installed until I realized that the connection at the phone was a little weak. I can't send any updates to WP7 via cab sender unless the phone is in a certain position to keep the connection from breaking.
boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Don't worry ... you can give the life to your phone back... it shows fail bcus u have 2.08.0000.. so it means u Sud have 2.08 v hspl.. so try flashing hspl by getting into bootloader(3 colour) by pressing volume down + power Then flash hspl.. but remember select 2.08v.. then again after flashing hold volume down + power.. bootlooder.. then flash magdlr 1.13 ... now the phone will boot into a black screen with written mangdlr.. wen the black screen magdlr screen comes then press power off for 5mintzz.. follow the guide to flash.. there is a stick thread in NAND DEVELOP... U can get the windows version back to your phone to get the warranty...
Sent from my HTC HD2 using Tapatalk
Ok ,, some good new at last ..
I have used the HSPL4 to change my 3.03hspl to 3.030000 spl...
Success, as when i go to the tri colour screen it says spl and no hint of hspl...
Bad news, is that i still cant get the rom flashing,, as it gets stuff at some point and mostly at 99%.. Have tried both ways through SD (leoimg) and through USB.
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.
boxboy said:
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.
Click to expand...
Click to collapse
did you try to flash just a splashscreen as i suggested in your other thread? (they can be flashed alone, no need for a whole rom, , just like radios)
if you can get a stock splashscreen on there you are sorted.
Maybe try to download the original Software from HTC.
With you serial number you can get the latest windows for this phone.
Flash the Software you get from HTC.
If this is working ok you can try to install any Android ROM.
Read at first this
http://forum.xda-developers.com/showthread.php?t=905841
Try to understand and follow the steps..
But if you have even no luck with original Windows soft. You will also (maybe) have a lot of probs. with Android..
Thank you guys for all your help..
I have flashed andriod on several phones some time ago and I actually forgot the right steps to follow.
But this phone is unique is not letting me finish.
After following all the right steps, i wasnt able to install a rom succesfully even after installing the HSPL... and I am also not able to install the factory rom from htc on either the hspl or spl settings.
But i now got rid of the NRG screen and I have also installed the spl 3.03.. When you on the phone, it displays software upgrade failed..
So I have now sent the mobile to HTC as it is under warranty. I will then re-flash andriod following the right steps and see what happens!
Thanks again!
My mobile came back from HTC with a week.. Looks like a brand new one!
In the letter it says the replaced IMEI, PCBA, FL BD, W/O_ REGIONAL_ID, LEO
WOW
GREAT PHONE... ITS MUCH FASTER THAN THE PREVIOUS ONE FOR SOME REASONS

Categories

Resources