Related
I flashed my Defy with froyo, then installed CM7, i charged it to 20% battery and turned it on. All worked fine for a couple of minutes, but afterwards it started restarting every 30 secs, So i tried flashing it again with the Chinese froyo (I'm from Israel, if it matters), but without charging the battery back to full, Which means I started flashing with about 15% battery.
I finished flashing rsdlite wrote "pass" and everything but the defy wouldn't power up, it just shows white led whenever i plug it to my PC. rsdlite recognized it in the first couple of hours and i tried flashing froyo again and again, but after a while even rsdlite didn't recognize it anymore.
I read a thread here that said that the phone doesn't charge in boot mode, and i thought that might be the problem, so i took out the battery and charged it at a phone store for about 15 minutes, then tried to turn it on but still no powering up. So now I have a defy that doesn't power up and isn't even recognized by rsdlite.
I'm hopeless, I loved my defy very much, and I really need an clue.
I'll do anything!
Thanks for reading this far, I hope you can help me
http://forum.xda-developers.com/showthread.php?t=892026 maybe this will help
Tried it, didn't work, I also tried to charge the battery already so I think its not just a dead battery problem, its probably more than that.
Hi there and welcome to the forums. You didn't mentioned which was the base OS you've had on your Defy before installing CM7, but I'll assume you have had a Froyo version, maybe the stock one (please provide more details).
If you flashed nordic SBF before installing CM7 or if you had official Froyo on your phone then you won't be able to Flash the leaked Chinese Froyo. It has some partitions with version code -2- like Eclair, whereas the nordic ROM has the code -4- and therefore it's not possible to directly downgrade by applying the Chinese SBF.
To revive your Defy you must charge your battery (at least 50% to be sure it will have enough juice and will last the whole process), then start it in stock recovery (Vold Down+ Power and then by pressing both volume buttons when the android with exclamation mark appears) and wipe data+cache. After this step you can start your phone in bootloader mode (Vol Up + Power) and flash again the initial ROM you had right before installing CM7.
you are from israel right?
why you choose chinese froyo for god sake?
some chinese froyo sbf is intended only for different DEFY (ME525) / Chinese Defy, and normal Defy is MB525.
it could damage your flashlight and phone.
use sbf from central europe froyo for best result installing CM7.
thanks guys, I charged the battery, got rsdlite to recognize the phone, and flashed a UK sbf, now its back on, working, and showing that motoblur animation.
I guess now all that's left is to install a 2.1 OS and everything should work.
(Please correct if I got this wrong, since I AM a noob and i really don't want to make another mistake)
THANKS ALOT!
If you flashed a full Froyo SBF then you cannot install Eclair SBF. It's not possible to directly downgrade after you have flashed Froyo using a full SBF. However you can easily flash a Froyo official ROM or... why not CM7 or MIUI.
Thing is... I already flashed 2.1, and got it to the point where it shows me the M logo. but it didn't go any further than that. i tried flashing a 2.3.3 ROM, same thing happens, M logo but nothing more. right now im back to this version of 2.2:
p3_jordan_umts_jordan-user-2.2.1-3.4.2-107_JDN-4-000000-release-keys-signed-T-Mobile-US.sbf
and I'm getting an animation of Motoblur with nothing else.
flaah nordic sbf then go to cm7. Follow the guide read first cm7 faq before proceeding
Sent from my MB525 using XDA App
All you do is flashing.. Have you actually do total wipe in recovery? Since you're having the motoblur animation splash screen, it is obviously your previous data is conflicting while the phone is trying to boot normally..
Sent from my awesome Moto Defy: Stock Rooted Gingerbread 2.3.3 - XDA Premium
farsight73 said:
All you do is flashing.. Have you actually do total wipe in recovery? Since you're having the motoblur animation splash screen, it is obviously your previous data is conflicting while the phone is trying to boot normally..
Sent from my awesome Moto Defy: Stock Rooted Gingerbread 2.3.3 - XDA Premium
Click to expand...
Click to collapse
I believe you are right about wiping, I've bricked my phone to the point i couldn't turn the phone on. So all you usually have to do is flash the full sbf, when it tries to boot it gets stuck on the m logo, just pull the battery, power it up holding volume down wait for the the triangle and press the middle of the volume rocker and it will take you to the stock recovery. Wipe and factory rest, flash the sbf again.
wipe/factory reset didn't fix it, though I noticed nordic sbf got it to show the android animation.
is it possible that I need to install a rom after I flash an sbf? and if so, how can I install a rom (custom recovery doesn't give me an option to install a zip, only "update.zip").
do I install some sort of 2ndinit?
do I install a rom through "update.zip"?
sorry once again for another (hopefully last ) noobish questions.
The SBF is a full ROM so atfer flashing a SBF there is no need to put another ROM via recovery, unless you want to do so (let's say you'd like to install CM7 or MIUI). If you haven't flashed a 2.3.4 full SBF you should be able to revive your Defy using the nordic SBF. Try to download it again or try a different one (one of those official SBF's released this summer).
I did install a 2.3.4 full sbf, but it too didnt work, tried a factory reset + cache wipe, and reflashing the 2.3.4 and it's still stuck on the M logo
Ive done something stupidly wrong.. Help me please..
Ok Ive a me525 and I tried to flash my phone with JRDNEM_U3_2.51.0_CHN_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA030.0R_USAJORDANRTINT_P029_A018_HWp3_Service1FF
Was not sure what I was doing at that moment(just following a guide/tutorial on YouTube)After the whole progress with RSD lite, my device turned black as the title says with only showing a white led light. Was getting pretty deperate thinking about I had broken the phone.. :crying:
I have searched for a solution on the forums saw some people did get their device repeared, but everything they had done didnt worked for me..
So please help this boy in need.. We dont have lots of money to spare so buying a new phone isnt really a fast option..
p.s. Not sure though but would a chinese sbf work and where would I find one?
Hi guys
Before I explain I'd like to say that yes, I have read other threads on similar topics, although none seem to have the same symptoms as me...
This week I bought a software-bricked Defy on eBay with the hopes of fixing it and giving it to a friend. I first tried flashing an old Eclair SBF to no avail (only switched on to bootloader) and thought that it could be failing due to it being on a newer firmware. So then I tried Froyo, and when that didn't work either (bootloops like when I received the phone) I thought my last resort was a CG 5 SBF, so I went for the JORDN_U3_97.21.51 build. This seems to get further into the booting process, with the MotoBLUR animation appearing but I get a BP Panic - 0x00080010 above the animation before the phone switches off. Thinking I had nothing to lose I tried a Gingerbread ROM, but that just bootlooped too so I went back to 97.21.51. I realise I've probably painted myself into a corner by flashing these
I'm all out of ideas with how to get the phone any further and have searched for the BP panic to no avail. I can get into stock recovery and bootloader, although the recovery seems to have issues with accessing the cache sometimes.
Thanks for reading
The same panic have y for the last 2 weeks, after flashing hangs in bootloader (red logo and no animation), after other flash hangs on a animated red logo and thats where you must give it time 3 or 4 min. wating, when its dont works you can try to pul out battery and do it in again while you hold the start and vol. down button, then in recovery menu wipe Dalvik cache and wipe cahe. Maby it works then, when not you can try like me to go again tho recovery and there restore stockrom, thats the way ym getting my defy work again. There are many ways to get it back to work again and it cost me 2 weeks after flashing maby 15 diverend roms to get it works and even than when it works, 2 days work whit rooting it and get 3G alive. So when you think its dead, maby RSDlite can bring it back to live, just like here.
Now my Defy MB525 working like a Defy 526 on Gingerbread.
So don't give up, when you can see whit RSDlite the phoon, it must be possible to get it work, only problem here was on a moment when the battery was empty, but here on XDA you can find the megayver method (charging on a ohter cell like a duo) or what y have don, get my old nokia loader (5V) and whit 2 wires hangs on the battery power it up to 4.1 V, succes.
Thanks, although I was just getting repeated boot loops rather than it hanging on the logo... And that wasn't animated either. How did you manage to restore the stock ROM through the recovery? Did you have a flashable zip? Please bear in mind that I did not get a custom recovery installed
I'll look out for the low battery problem. Thanks for your advice
ben_duder said:
Thanks, although I was just getting repeated boot loops rather than it hanging on the logo... And that wasn't animated either. How did you manage to restore the stock ROM through the recovery? Did you have a flashable zip? Please bear in mind that I did not get a custom recovery installed
I'll look out for the low battery problem. Thanks for your advice
Click to expand...
Click to collapse
U should have wiped cache and data after flashing Froyo!!!!!!
It would have booted!!!!
Now u flashed GB!! Ur stuck there!!!
Flash gb again and Go to stock recovery and wipe data!!!! If know how to do it!!!
Sent from my MB526 using xda premium
nogoodusername said:
U should have wiped cache and data after flashing Froyo!!!!!!
It would have booted!!!!
Now u flashed GB!! Ur stuck there!!!
Flash gb again and Go to stock recovery and wipe data!!!! If know how to do it!!!
Sent from my MB526 using xda premium
Click to expand...
Click to collapse
Thanks, although I'm pretty sure I did wipe cache and data... and I definitely did (several times ) after flashing Gingerbread. I feel like whatever is preventing Froyo and Gingerbread from booting is the same thing as what is giving me the BP panic on the CG 5 Eclair ROM.
I would suspect a hardware issue here.w
Sent from my MB525 using Tapatalk
I think it might be too It's a shame because I can enter recovery and bootloader okay, and the seller said it broke during a failed software update so I thought it would be a simple matter of reflashing an SBF.
what is bp panic?
what happens when it is booting?
Sent from my MB525 using xda premium
When I try to boot the CG 5 Eclair I get past the static Motorola logo (hence further than any other build) but the MotoBLUR animation is stuttery, with a BP panic at the top (see picture). This goes on for quite a while, then the phone switches off and this loops.
Ok if occurred during a software update, find out which he was installing and try that one. May also be worth trying motoupdate.
Sent from my MB525 using Tapatalk
I might try that, but won't it be useless now that I've flashed CG 5? I'll look into MotoUpdate
Is the general consensus that this is an unfixable hardware issue, then?
Apolgoies if you've already tried this, but I had a Defy which would do the same, either stuck on M logo or error in bootloader.
Each time I just plugged it into PC / USB at bootloader screen, and used RSD Lite to try another ROM. Eventually I found one which worked. I think I tried 5 before finding one which didn't cause any problems.
My defy was a ME525+ and the ROM which finally worked was "DEFYPLUS_U3_4.5.1-134_DFP-132_BLUR"
So, if you haven't already, I'd just suggest try a few more ROMS, flashed from Bootloader / RSD Lite.
Hope it helps somehow
So i just bought a defy+, and i figured i'd flash the newest available stock rom on it for the best performance, so i flashed the one in this thread: http://forum.xda-developers.com/showthread.php?t=1375701
Now my phone won't boot, shows only black screen, and when i connect to a pc it says Motorola Flash Interface, but it doesn't show anything on the screen. I've tried all the recover tuts on the forum, and still no luck. Is my moto bricked already? Nothing works, i've flashed a different SBF 10 times i think, all no luck, while the flashing application (RSD Lite) shows passed all the time
Thanks in advance
Flash a bl7 sbf(dfp-231). It will boot. And wipe data from stock recovery
Sent from my MB526 using xda premium
- So I was updating to Quarx's 5th Nov build (2ndboot) and in the middle the flash my phone turned off and decided not to start up. (The battery WAS NOT drained)
- I started with this guide in order to get it back to life:
http://forum.xda-developers.com/showthread.php?t=1807899(I used the exact same files, even the sbf. I live in India and I couldn't find India's sbf in this list: http://sbf.droid-developers.org/umts_jordan/list.php)
- Everything went as excepted and I was back on 2.2.2, so I tried to flash Quarx's build again. (I installed gapps, and cleared everything twice, thrice). However, the phone stuck on a bootloop:
red Motorola logo -> blue led -> greend led -> blank screen -> repeat.I cleared the cache's, factory reset, etc etc. No use.
- So i followed the original method again to get back to 2.2.2 and then flashed ICS from Cyano's website. It worked! So I tried again to flash a CM10 release, but this time a PRE-2ndboot build - 24th Sep.
It didn't work either. So JellyBean is the evident problem, but it doesn't make any sense, right?
- I started agin and tried to flash a different sbf, I got to this thread:http://forum.xda-developers.com/showthread.php?t=1093352 and tried the sbf provided (they claim it to be the one for SEA, including India). However, even after doing a factory reset from the stock recovery and flashing this sbf, I got a brick. The phone won't start whatsoever. No bootloader, no recovery - zilch. Dead.
- I again went back to my original method and got back to ICS...Flashed JB -> Same bootloop as before.
- Somethings I have noticed:
1. On flashing, the internal memory shrinks to only 128MB. I tried a factory reset from within the phone, from custom recovery and from the stock recovery. The memory was still 128MB with about 40MB free.
2. When I return to stock, the phone is somehow pre-rooted. On running superOneClick it shows that it;s already rooted but I continue nonetheless.
3. I think MAYBE the low internal storage might be at fault since JB Gappa require a lot of space.. I have tried it with minimal gapps too.
4. I have flashed every sbf available for Asian countries...but the only one that works is the one from the first link provided.
5. The only thing I can do right now is get to 2.2.2 or ICS...So if someone can help me out, that's my current status.
PS - I have been at it for 3 straight days, so yea, I have tried just about everything and read every thread regarding this. I even had to jump start by battery once as it ran out in the middle of a sbf flash.
There s a chance you didn't installed JB the right way. Also you ca install it without Gaaps. Does 2nd boot got enabled in Bootmenu? Did you flashed the kernel accordingly?
if you have bl4 try one of my fixed sbf with 2ndboot
ex. 28.11JB.Quarx+jellyX.kernel
than make a data and cache format fom bootmenu
bootmenu/ CPU settings/ system tools/ format data and cache to ext3
reboot
hve the link in my signature
I think you need bl. 4 from an 2.3.4 sbf for defy
In my country there was as an official update to GB
Users posted prblems with bootloader 3 and 7 @ quarx cm10 2ndboot roms
MB525 red lense
Hi,
You can take one more try (if you wanna ) to flash 12.09 JB build - it shall work
If so then flash Nordic retail 2.2.2 or WE retail (U3_3.4.2-177 or 179 from here)and try again 2ndboot builds (for some sbfs the last pre 2ndboot, 24/09 was the first not working)
Flash then 5/12 and jb gapps, wipe dalvik cache and cache after flashing.
Concerning 128 MB free memory - I suppose you are talking about data partition, not a system. Of course it is too small - the same as prerooted phone - try another sbf
Okay, just to clear the air - I was running Quarx's 28th Nov build before this happened.
I solved the 128MB problem. I'm currently on ICS 4.0.4 on the 16/07 CM9 build. It now shows 1.7GB internal available.
The kernel version shows 2.6.32.9-gb08c3c8xxxx..xxx.
I'm going to try and flash the 5/11 CM10 build (2ndboot). But before that I would to confirm the procedure:
1. Custom recovery
2. Data/Factory Reset
3. Clear cahce, Dalvik cache
4. Flash 05-11
5. Flash gapps (?) gapps-jb-20121011-signed.zip?
6. Clear cache, dalvik
7. Reboot
Should I go ahead with this?
PS. I reached my current state by flashing the sbf and firmware provided in this post: http://forum.xda-developers.com/showthread.php?t=1807899
I'll wait till someone approves of this, I don't want to brick it again.
vinu.shukl said:
Okay, just to clear the air - I was running Quarx's 28th Nov build before this happened.
I solved the 128MB problem. I'm currently on ICS 4.0.4 on the 16/07 CM9 build. It now shows 1.7GB internal available.
The kernel version shows 2.6.32.9-gb08c3c8xxxx..xxx.
I'm going to try and flash the 5/11 CM10 build (2ndboot). But before that I would to confirm the procedure:
1. Custom recovery
2. Data/Factory Reset
3. Clear cahce, Dalvik cache
4. Flash 05-11
5. Flash gapps (?) gapps-jb-20121011-signed.zip?
6. Clear cache, dalvik
7. Reboot
Should I go ahead with this?
PS. I reached my current state by flashing the sbf and firmware provided in this post: http://forum.xda-developers.com/showthread.php?t=1807899
I'll wait till someone approves of this, I don't want to brick it again.
Click to expand...
Click to collapse
Ok, so you flashed JORDN_U3_97.21.51, which means 24/09 and 2ndboot builds will not work.
They could work before when you had 2.2.2 on board.
You need another full sbf, and as you flashed BL5 it means you cannot go back to froyo. You shall find working BL5 sbf or go to BL6 one like U3_4.5.1-134_DFP137 or 139
And procedure above is correct
Ps. Method from post given by you was found out a long time ago, when some ppl flashed first gingerbread and then needed to go back to froyo. It is not a proper one for all defy users with still valid warranty in most of regions
corrinti said:
Ok, so you flashed JORDN_U3_97.21.51, which means 24/09 and 2ndboot builds will not work.
They could work before when you had 2.2.2 on board.
You need another full sbf, and as you flashed BL5 it means you cannot go back to froyo. You shall find working BL5 sbf or go to BL6 one like U3_4.5.1-134_DFP137 or 139
And procedure above is correct
Click to expand...
Click to collapse
These are the sbf's I found pertaining tp your specifications:
http://i.imgur.com/muQdT.jpg
EDIT: But they are all in the DEFY-PLUS repository...can I flash them?
So I can use anyone of them?
Also, I don't know much about BL versions...So should I just download one of the above sbf's and flash it using RSD? Do I need a nandroid backup to go with it too?
The procedure I would follow would be:
1. Factory reset, clear cache's
2. Go into bootloader menu
3. Flash above sbf using RSD
4. Reboot ??
Should that suffice?
First: if you are red lense it is ok to flash BL6
If you are green lense, to have your camera working, you will need 2ndboot builds (CM9, 10 or 7)
You will probably need red lens battery fix to show correct percentage, no matter you have green or red lense then.
You can flash it even later, after flashing CM10 and gapps and checking how it works
I would choose Nordic retail
Sometimes you can have problems with rooting with SuperOneClick (version 2.3) - force close Motorola Portal before rooting and it shall work ok then
And nandroid backup is not very useful when changing BL version, at least you will not be able to restore all
I have a green lens MB525.
So I'm downloading Nordic Retail for MB526 and will flash it using RSD.
After that, I can straight away flash any cm10 build right? (like the latest 5th Nov)
vinu.shukl said:
I have a green lens MB525.
So I'm downloading Nordic Retail for MB526 and will flash it using RSD.
After that, I can straight away flash any cm10 build right? (like the latest 5th Nov)
Click to expand...
Click to collapse
Yes, just normal procedure with rooting and 2ndinit installation, then flashing CM10 and jb 4.1 gapps with all proper wipings
And as mentioned above probably battery fix will be required for proper percentage - you will see
corrinti said:
Yes, just normal procedure with rooting and 2ndinit installation, then flashing CM10 and jb 4.1 gapps with all proper wipings
And as mentioned above probably battery fix will be required for proper percentage - you will see
Click to expand...
Click to collapse
Okay!
Gonna flash it tonight...Finger's crossed. =D
UPDATE: Flashed the Nordic Retail successfully. On stock 2.3.6 right now. Going to flash CM10-20121205-NIGHTLY-mb526.zip
UPDATE: I tried rooting it using SuoerOneClick v2.3.3.0 and even killed Moto Helper from PC and chose 'None' from the USB connection menu on the device. This is what I got:
http://i.imgur.com/cokl3.jpg and after reboot http://i.imgur.com/arZzd.jpg
SuperOneClick stopped responding after that. I waited 10 mins but nothing happened...No input requested from the device. tried it again but with the same results.
What should I do? Try z4root?
vinu.shukl said:
UPDATE: Flashed the Nordic Retail successfully. On stock 2.3.6 right now. Going to flash CM10-20121205-NIGHTLY-mb526.zip
UPDATE: I tried rooting it using SuoerOneClick v2.3.3.0 and even killed Moto Helper from PC and chose 'None' from the USB connection menu on the device. This is what I got:
http://i.imgur.com/cokl3.jpg and after reboot http://i.imgur.com/arZzd.jpg
SuperOneClick stopped responding after that. I waited 10 mins but nothing happened...No input requested from the device. tried it again but with the same results.
What should I do? Try z4root?
Click to expand...
Click to collapse
You can try z4root, though I rooted it with SOC 2.3.1 without problem. It seems that rooting didn't even start. Try choose zergRush instead of Auto
Note that USB is changing to Motorola Portal every several seconds if you do not kill it from a phone and it stops the process. Go to app settings, choose all apps, force close Motorola Portal (or freeze it - do not remember if such option is available)
Have you choosed USB debug mode?
Eventually try factory reset from settings before rooting
corrinti said:
You can try z4root, though I rooted it with SOC 2.3.1 without problem. It seems that rooting didn't even start. Try choose zergRush instead of Auto
Note that USB is changing to Motorola Portal every several seconds if you do not kill it from a phone and it stops the process. Go to app settings, choose all apps, force close Motorola Portal (or freeze it - do not remember if such option is available)
Have you choosed USB debug mode?
Eventually try factory reset from settings before rooting
Click to expand...
Click to collapse
Okay...I rebooted the phone and the PC and re-installed the Moto drivers...success!
Installing SndInitDefy_2.3.apk
UPDATE: Booted into custom recovery. Factory/data wipe. Cache, Dalvik wipe. Installing CM10-20121205-NIGHTLY-mb526.
vinu.shukl said:
Okay...I rebooted the phone and the PC and re-installed the Moto drivers...success!
Installing SndInitDefy_2.3.apk
UPDATE: Booted into custom recovery. Factory/data wipe. Cache, Dalvik wipe. Installing CM10-20121205-NIGHTLY-mb526.
Click to expand...
Click to collapse
You are lucky :laugh: - for many users (probably depends on sbf flashed) SndInit 2.3 does not work, I still use 1.4.2
You can also flash this zip - it changes the ramdisk to the older version and helps in battery life
corrinti said:
You are lucky :laugh: - for many users (probably depends on sbf flashed) SndInit 2.3 does not work, I still use 1.4.2
You can also flash this zip - it changes the ramdisk to the older version and helps in battery life
Click to expand...
Click to collapse
I guess I had some luck coming my way after a week of real hard times...
I'm currently restoring all my apps... Do I install this like any other zip i.e. clear cache + dalvik -> flash -> clear cache + dalvik ?
Also, since we are on the topic of performance, what are the optimum CPU settings?
I'm currently using:
1200,900,600,300 - 62,47,32,17
Interactive CPU Governor
SIO I/O Scheduler
No changes in the Memory Managment options (i.e. zRam, purginf of assests and kernel samepage merging - all are turned off)
16bit transparency turned off.
vinu.shukl said:
I guess I had some luck coming my way after a week of real hard times...
I'm currently restoring all my apps... Do I install this like any other zip i.e. clear cache + dalvik -> flash -> clear cache + dalvik ?
Also, since we are on the topic of performance, what are the optimum CPU settings?
I'm currently using:
1200,900,600,300 - 62,47,32,17
Interactive CPU Governor
SIO I/O Scheduler
No changes in the Memory Managment options (i.e. zRam, purginf of assests and kernel samepage merging - all are turned off)
16bit transparency turned off.
Click to expand...
Click to collapse
The ramdisk zip is to be installed in a standard way, like any other zip, probably doesn't require wiping caches, but probably
I usually use zRam (18%) - I didn't notice any bigger battery drain.
KSM off
WiFi - change to never when screen is off - you can have wifi on all the time without special battery drain
And choose proper baseband for you region
And CPU settings are ok as above
Defy on BL6
Ok guys I give up. I read and tried pretty much all the options net offered. Here is the problem:
I have green lens MB525. I bought it second hand in INDIA, it was running ICS. I switched to CM7 and it was working flawlessly for good 6 months. I did a reset and then it got stuck at recovery and showered error in some directories. So i triedro redo the CM7 procedure and loaded zip on root of SDcard. It didn;t changed anything. I did flashing and wiping the dalvik cache and memory, tried again, and again it was the same story.
Then i tried trying different SBF and it always used to get stuck at logo, i didn't bothered reading more about issue and stupid me flashed JORDN_U3_97.21.51. After that it started showing error in bootloader. It shows bootloader 09.10, Err: A5,69,35,00,27. I tried to use previous SBF and it then completely bricked it, only white light and black screen. Only when i again flashed it with JORDN_U3_97.21.51 it showed white motorola logo and bootloader version and error. I read this thread and tried the two firmwares using BL5 and BL6 in that order and its logo had changed to RED Motorola logo, but again the same bootloader menu with its version and error.
I had battery issues too, since i have been thinking and trying on it for past 10 days. Since i have battery charger, i used to charge the battery separately and plug it back in before flashing using RDSlite 5.6.
As of now i am stuck with a paperweight which i can only flash. I tried pressing down volume button to get into recovery but no matter what button i press it always ends up in bootloader. All help will be appreciated.
Vycas
---------- Post added at 06:03 PM ---------- Previous post was at 05:48 PM ----------
corrinti said:
Ok, so you flashed JORDN_U3_97.21.51, which means 24/09 and 2ndboot builds will not work.
They could work before when you had 2.2.2 on board.
You need another full sbf, and as you flashed BL5 it means you cannot go back to froyo. You shall find working BL5 sbf or go to BL6 one like U3_4.5.1-134_DFP137 or 139
And procedure above is correct
Ps. Method from post given by you was found out a long time ago, when some ppl flashed first gingerbread and then needed to go back to froyo. It is not a proper one for all defy users with still valid warranty in most of regions
Click to expand...
Click to collapse
Ok guys I give up. I read and tried pretty much all the options net offered. Here is the problem:
I have green lens MB525. I bought it second hand in INDIA, it was running ICS. I switched to CM7 and it was working flawlessly for good 6 months. I did a reset and then it got stuck at recovery and showered error in some directories. So i triedro redo the CM7 procedure and loaded zip on root of SDcard. It didn;t changed anything. I did flashing and wiping the dalvik cache and memory, tried again, and again it was the same story.
Then i tried trying different SBF and it always used to get stuck at logo, i didn't bothered reading more about issue and stupid me flashed JORDN_U3_97.21.51. After that it started showing error in bootloader. It shows bootloader 09.10, Err: A5,69,35,00,27. I tried to use previous SBF and it then completely bricked it, only white light and black screen. Only when i again flashed it with JORDN_U3_97.21.51 it showed white motorola logo and bootloader version and error. I read this thread and tried the two firmwares using BL5 and BL6 in that order and its logo had changed to RED Motorola logo, but again the same bootloader menu with its version and error.
I had battery issues too, since i have been thinking and trying on it for past 10 days. Since i have battery charger, i used to charge the battery separately and plug it back in before flashing using RDSlite 5.6.
As of now i am stuck with a paperweight which i can only flash. I tried pressing down volume button to get into recovery but no matter what button i press it always ends up in bootloader. All help will be appreciated.
Vycas
@Vycas
The problems might be several, unfortunately even hd problem, but try this:
- try different USB cable, different computer, different USB socket - the problem can arise when signal transmission is poor. Sometimes reinstalling of motorola drivers also helps
- if above does not help try Linux computer instead of Windows one
Regarding sbf - well, as you received error after each sbf flashing there could be a hope that you still may have BL4 (but also you may have BL6) - start your above mentioned trials with BL4 sbf, which will give you camera also with CM7
Hi all
So, I have a problem with my Defy (MB525 green lens). The best will be, if I'll write my full story. Here is it:
Story
I had Defy with CM 10. It had bloated battery. I wasn't using it for 6 months because I have another phone.
Some time ago, I decided, that I'll give Defy to my grandfather. On Tuesday this week I bought new original battery. I put it in the Defy, and charge it. I could boot up my old system as I wrote, CM 10. While it was charging, I detected that I haven't got SD Card. On the other hand, I found some 4GB Samsung SD, which had my father in his Desire. The SD Card had 3 partitions, which I tried to delete, and make only one, with GParted. After I did it, Linux and Windows can't see it. (This is almost other problem, which I'm trying to solve here http://crunchbang.org/forums/viewtopic.php?pid=350683)
But, when I put the CD Card to Defy, in TWRP recovery I could see some strange symbols. I thought, that I can repair something when I wipe SD Card. When the battery charged, I decided to do factory reset and wipe SD card. Here is my first failure. In TWRP I went to custom wipe, and here I marked everything including system and I wiped it. Then I remembered that system is recovery too. TWRP wrote, that everything except SD-Ext and SD was wiped. I known that this will be a problem. Yes, after reboot only Motorola logo without recovery.
I think, there was only one option - flash SBF, which I did. I went to stock bootloader and with sbf flash in Linux, I flashed this:
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF.sbf
And than this:
CM7RC1.5_16_09_11_custom.sbf
After reboot, I got bootloop. I tried to replace battery, do factory reset but nothing helped. That time I haven't got working card, so I couldn't flash some zip via CWM recovery. Thus, I again flash another SBF, but I don't really remember which. Probably some official CEE Froyo however, I'm not sure.
After that and reboot, I got only black screen with white led lighting while USB was connected. When I wanted to go to stock bootloader, still black screen, but I can flash SBF, and while flashing, screen have brightness and text about flashing.
I knew that this is little hard brick. I again tried to flash other SBF which I have or I downloaded (yes, again I don't know which). One of SBFs which I flashed was some fixed Chinese SBF . That made my defy booting, screen working, but still bootlooping. I couldn't reach any recovery.
Again, I flashed other SBFs, CM's too but nothing worked and I got black screen again.
And this was end of my story.
Current situation
I have Defy (MB525 green lens), with unknown framework an it had only black screen and what only I can do, is break Defy with hammer or flash some SBF.
So, here is list of all SBF files, that I have downloaded and probably tried to flash: (No order)
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF.sbf
CM7RC1.5_16_09_11_custom.sbf
JRDNEM_U3_2.51.1_BLUR_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA030.0R_USAJORDANO2DE_P048_A015_HWp3_Service1FF.sbf
JRDNEM_U3_3.4.2_177-003_BLUR_SIGN_SIGNED_USAJRDNEMARAB1B8RTGB03A.0R_PDS03C_USAJRDNFRYORTGB_P019_A010_HWp3_Service1FF.sbf
DFPRC_U_4.5.3-109_DPP-6-7_SIGNED_USADEFYPRCB1B50AA00A.0R_JRDNGIBRRTGC_P025_A019_HWp3a_Service1FF.sbf
JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF.sbf
JORDN_U3_97.21.51.sbf
JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P011_A010_HWp3_Service1FF.sbf
4.5.1-134-DFP-132-gingerbread-BL6-fixed.sbf
4.5.2-109-DHT-22-gingerbread-BL5-fixed.sbf
3.4.2-177-003-nordic-froyo-fixed.sbf
3.4.2-179-002-tmobile-froyo-fixed.sbf
4.5.1-134-DFP-74-gingerbread-BL5-fixed.sbf
4.5.3-109-DPP-11-gingerbread-BL5-fixed.sbf
JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN.sbf
Probably that is all what I have.
I've read many topics with similar problem and guides, but nothing helped me, or SBFs were unavailable.
So, what have I to flash, or which guide to try, if I want working Defy?
Sorry for my not good English
Thanks
UPDATE
sterver1 said:
Wohooo!!
Story
After a long time (4 months)...
Accidentally today I found my favorite custom ROM - MoKee OS, for Defy. I said to myself: "Hm, I have some time... I'll try to flash this MoKee on my Defy and maybe it solve my problem with (not) charging/unknown battery for system."
I picked out box with Defy from drawer, wiped the dust, took the Defy and said: "Sh*t! I haven't got SD Card!" Fortunately I found one. I download MoKee OS zip on that SD Card, put it to Defy, booted to recovery and flash MoKee OS zip. (...with full wipe of course...) Then rebooted to system.
Uselessly. Still unknown battery. "Hmm, It doesn't matter. Maybe here are some new stuffs which can solve my problem." And I continued to finding something, that can solve my problem. After a while I found ROMs with new 3.0 Kernel by Quarx. HERE. I downloaded CM 11 EXPERIMENTAL with this kernel and update recovery and flashed them. I didn't read thread. After reboot system didn't boot up and TWRP was inaccessible. I found why when I read some posts from that thread. HERE. But I couldn't flash that zip via recovery because I couldn't open recovery. So I mount /system to USB from bootloader and added files from zip manually to /system partition. After reboot it jammed on booting up. But TWRP was accessible so I did full wipe and flashed CM 11 EXPERIMENTAL and than that fix zip by @lorcotti. After that it finally booted up and battery was working and charging!
And they all lived happily ever after. :laugh:
SO, If you have some problem as me (unknown battery after flashing GB SBF on MB525), try this:
1. Download recovery and some ROM from [Kernel][GPL] Development 3.0 Kernel and fix from this post.
2. Put all zips on your SD Card.
3. Boot up to recovery.
4. Flash update-recovery.zip.
5. Reboot to recovery.
6. Do full wipe.
7. Flash ROM with 3.0 Kernel.
8. Flash Fix.
9. Wipe cache and dalvik cache.
10. Reboot to system.
If you want, you can flash GAPPS via recovery too.
But this will not be for daily usage! 3.0 Kernel by Quarx have a lot of bugs!
Thanks all!
Click to expand...
Click to collapse
Yeah!
Today I again tried to flash chines SBF. This one: JDGC_U6_2.13.0 China Unicom Thread/Download !!!BL6 kernel !!!
JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF.sbf
...and now I have bootable phone . I read many topics again and I got to know how to aces stock recovery. So I made wipe on this chines ROM and I can boot without loop, but I can only do emergency call with SIM it is the same. So, now, I don't know, what have I to do/flash, how to root it and flash here custom rom. Can I use SuperOneClick if it probably haven't got turned on USD Debugging?
Back on black
So, I made sbf file with depacker...
CMG39 from JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P011_A010_HWp3_Service1FF
and all others from JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF except CMG31.
Than the bootscreen changed from chines logo to grey motorola logo and I got Bootloader (9.00) Error A5,70,39,00,27. After that I flashed another sbf and I got Error A5,70,00,00,23. Than I flashed DEFYPLUS_U3_4.5.1-134_DFP-231_CEE_ROOTED_No_Signed.sbf and now I again have only black screen. F*ck!
I tried to flash my made sbf and chines one (JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF) too but nothing...
Really here is nobody who can help please??? I want give Defy as Christmas gift. :crying:
OK, so repetition.
What mistakes I've made
1. I wipe wipe all including system partition in TWRP without any flashable zip on SD card.
2. I continued with flashing original SBF, while I have usable CWM.
3. I flashed many no downgradable GB SBFs.
4. I flashed Defy Plus SBF on Defy.
I hope that there is still hope.
Somehow to downgrade, flash only CWM where I can flash nandroid backup or I don't know what else...
a gingerbread sbf should also work on green lens defy as there is no diff. in hw... instead the cam
have you tried a factory reset in stock recovery after sbf flash ?
Sent from my MB526 using xda app-developers app
Now, after all (which I tried) SBFs I get only black screen. I tried many GB SBFs too, but still black screen...
I'm going to try some another Poland SBFs and than if that won't work, I'll try to flash all in Froyo CEE SBF particularly.
Thanks for your response.
Once you've flashed GB stock sbf you can't go back staight to froyo or else
Read the beginners guide and the SBF matrix sektion carefully.. if you haven't...
Sent from my MB526 using xda app-developers app
DFP 231 has been flashed by you, so no froyo sbf will work. Black screen on dfp 231 indicates some eMMC problem, because bl version is highest(no error possible). IMHO only service centre can disable bl check or replace the main board to fix the problem
The problem should have been solved at the boot loop issue by wiping from stock recovery, no network solved by baseband/radio fixes. Check the rsdlite log file to confirm checksum/access errors. I think that the custom sbf somehow messed up either eMMC or efuse(less likely, unheard of).
For sdcard error wipe everything using hdd llf. If any error persists it's a hardware issue
Sent from my MB526 using Tapatalk 4
@bone101
I know, I read it few times, and I know how it is (not) working. But, after all GB SBFs I got only black screen, so maybe were not correctly flashed... I'm using Linux and here is sbf_flash for flashing SBFs, and in it I can't view informations about phone as in RSD Lite... But maybe, it will work in wine..
Do you now, that if I flashed GB SBF, I have to flash another GB to solve my problem, because no Froyo will work?
@thekguy
I know how I can solve others problems. Only what I need help to solve is black screen.
Can't I flash something which support that high BL or it won't work?
check if you get into Bl. modus
press vol. up & then power button
tell what you see
Sent from my MB526 using xda app-developers app
That's what I'm saying, the black screen problem occurs due to bl version mostly, and you have highest bl, so in theory black screen is impossible. Unfortunately I have never seen in this forum any defy recovering from black screen after flashing dfp231. Check rsd log from windows if possible. Froyo sbf cannot work under any circumstance. You must flash only gb sbf
Sent from my MB526 using Tapatalk 4
@bone101
When I acess bootloader I have only black screen... While flashing I can see
"SW Update
In progress.."
Ok, I have Windows notebook available... Here are device properites from RSD Lite:
IMEI/ESN/MEID: N / A
Technology: N / A
Software Version: N / A
Flex Version: N / A
Bootloader Version: v0x000910
DRM Version: N / A
AP Die ID: 173002052f066b010000dcff0200
BP Die ID: 0000000000000000000000000000
AP Public ID: d0d8842b4879dd27b9eb94f970fbeec252fcb2f4
BP Public ID: 0000000000000000000000000000000000000000
Click to expand...
Click to collapse
I'm going to try some GB SBFs here...
WOHOOO I've got it! I flashed 231_GR_SIGN_UCADEFYEMARAB1B80AA004.0R_PDS03C_USAJRDNGIBRRTCEE_P022_A022_Service1FF.sbf and now I have got bootable phone... I'm in the system. I'm going to root it and flash CWM and MIUI if it will work.
Really thanks for your help!
sterver1 said:
@bone101
When I acess bootloader I have only black screen... While flashing I can see
"SW Update
In progress.."
Ok, I have Windows notebook available... Here are device properites from RSD Lite:
I'm going to try some GB SBFs here...
WOHOOO I've got it! I flashed 231_GR_SIGN_UCADEFYEMARAB1B80AA004.0R_PDS03C_USAJRDNGIBRRTCEE_P022_A022_Service1FF.sbf and now I have got bootable phone... I'm in the system. I'm going to root it and flash CWM and MIUI if it will work.
Really thanks for your help!
Click to expand...
Click to collapse
I'm stuck in same problem, downloading this sbf you mention before, hope it works. Fu^kin defy, it sucks
@Alejandrissimo
Good luck...
I have another problem. Now, I have GB kernel. In original 2.3.6 GB on MB525 green camera don't work, and battery too. So, I thought that, when I flash Froyo kernel (CM) and CM7 I got back Froyo kernel and working camera and battery. Yes, this was not possible. After I did it and rebooted it I got Bootloader error. I flashed DFP-231 again. Worked.
Than I tried restore Froyo from nandroid which I found something here on forum. Than I flashed CM7 and bootloader error again.
Now I have CM7 by Maniac for defy plus which worked well except camera and battery... I know that here are many topics about downgrading, camera fixing and others but all which I read are bad in something for me...
Here are some options what I found but I don't know if I can use one:
Method 2: (BIG thanks to Jebrew again for this one)
NOTE: You are going to need CM7 for this one. CM7 Stable version recommended.
Click to expand...
Click to collapse
from http://forum.xda-developers.com/showthread.php?t=1216982
DOWNGRADE
If you come from Android 2.1 and never flashed Android 2.2 you can use the fixed sbf-files method. With this method you will have a option to downgrade to you personal stock Android 2.1 via direct sbf flash.
Click to expand...
Click to collapse
from http://forum.xda-developers.com/showthread.php?t=966537 but I'v ever flashed Android 2.2.
Or http://forum.xda-developers.com/showthread.php?t=1465436 ... This is better option but I have flashed full 2.3.6 SBF and here is:
It will only work if you never flashed a Android 2.3.6 full sbf.
Click to expand...
Click to collapse
So, how can I downgrade or repair battery and camera? I don't care whether I have got GB or Froyo kernel if I have working camera and battery.
have you tried cm11 ?
or ms2ginger by walter79
Sent from my MB526 using xda app-developers app
sterver1 said:
@Alejandrissimo
Good luck...
Click to expand...
Click to collapse
Working and rooted, thanks for your help
Alejandrissimo said:
Working and rooted, thanks for your help
Click to expand...
Click to collapse
please see your PN
sterver1 said:
@Alejandrissimo
Good luck...
I have another problem. Now, I have GB kernel. In original 2.3.6 GB on MB525 green camera don't work, and battery too. So, I thought that, when I flash Froyo kernel (CM) and CM7 I got back Froyo kernel and working camera and battery. Yes, this was not possible. After I did it and rebooted it I got Bootloader error. I flashed DFP-231 again. Worked.
Than I tried restore Froyo from nandroid which I found something here on forum. Than I flashed CM7 and bootloader error again.
Now I have CM7 by Maniac for defy plus which worked well except camera and battery... I know that here are many topics about downgrading, camera fixing and others but all which I read are bad in something for me...
Here are some options what I found but I don't know if I can use one:
from http://forum.xda-developers.com/showthread.php?t=1216982
from http://forum.xda-developers.com/showthread.php?t=966537 but I'v ever flashed Android 2.2.
Or http://forum.xda-developers.com/showthread.php?t=1465436 ... This is better option but I have flashed full 2.3.6 SBF and here is:
So, how can I downgrade or repair battery and camera? I don't care whether I have got GB or Froyo kernel if I have working camera and battery.
Click to expand...
Click to collapse
Congrats man! Seems that rsdlite on Windows is the most reliable solution. Now to fix everything just flash cm10 (jelly bean) or later rom. It includes fixes for camera and battery
Again, no downgrading bl(not even jtag will work)
Sent from my MB526 using Tapatalk 4
Oh, ok. I'll try it. Thanks.
Hmm, and than, can I flash CM7 by Maniac or JB/GB WIUI and fixes in CM10 will still working?
Ms2ginger is not good for me because it haven't got slovak language. I'll give defy to my grandfather.
//And now, in Quarx CM 10 my battery don't charge. I tried 2 chargers and charging via USB too.
In options, battery is still "60% - Unknown"
Alejandrissimo said:
Working and rooted, thanks for your help
Click to expand...
Click to collapse
Hehe, I'm glad...
sterver1 said:
Oh, ok. I'll try it. Thanks.
Hmm, and than, can I flash CM7 by Maniac or JB/GB WIUI and fixes in CM10 will still working?
Ms2ginger is not good for me because it haven't got slovak language. I'll give defy to my grandfather.
//And now, in Quarx CM 10 my battery don't charge. I tried 2 chargers and charging via USB too.
In options, battery is still "60% - Unknown"
Hehe, I'm glad...
Click to expand...
Click to collapse
There's a cm7 2ndboot build which should work for you. Try cm10.1 or above, problem should be solved.
JB wiui includes those fixes, as does cm7 2ndboot. I don't think that wiui GB has them. I would personally go for cm10.1 or above
Sent from my MB526 using Tapatalk 4