I flashed my Defy with froyo, then installed CM7, i charged it to 20% battery and turned it on. All worked fine for a couple of minutes, but afterwards it started restarting every 30 secs, So i tried flashing it again with the Chinese froyo (I'm from Israel, if it matters), but without charging the battery back to full, Which means I started flashing with about 15% battery.
I finished flashing rsdlite wrote "pass" and everything but the defy wouldn't power up, it just shows white led whenever i plug it to my PC. rsdlite recognized it in the first couple of hours and i tried flashing froyo again and again, but after a while even rsdlite didn't recognize it anymore.
I read a thread here that said that the phone doesn't charge in boot mode, and i thought that might be the problem, so i took out the battery and charged it at a phone store for about 15 minutes, then tried to turn it on but still no powering up. So now I have a defy that doesn't power up and isn't even recognized by rsdlite.
I'm hopeless, I loved my defy very much, and I really need an clue.
I'll do anything!
Thanks for reading this far, I hope you can help me
http://forum.xda-developers.com/showthread.php?t=892026 maybe this will help
Tried it, didn't work, I also tried to charge the battery already so I think its not just a dead battery problem, its probably more than that.
Hi there and welcome to the forums. You didn't mentioned which was the base OS you've had on your Defy before installing CM7, but I'll assume you have had a Froyo version, maybe the stock one (please provide more details).
If you flashed nordic SBF before installing CM7 or if you had official Froyo on your phone then you won't be able to Flash the leaked Chinese Froyo. It has some partitions with version code -2- like Eclair, whereas the nordic ROM has the code -4- and therefore it's not possible to directly downgrade by applying the Chinese SBF.
To revive your Defy you must charge your battery (at least 50% to be sure it will have enough juice and will last the whole process), then start it in stock recovery (Vold Down+ Power and then by pressing both volume buttons when the android with exclamation mark appears) and wipe data+cache. After this step you can start your phone in bootloader mode (Vol Up + Power) and flash again the initial ROM you had right before installing CM7.
you are from israel right?
why you choose chinese froyo for god sake?
some chinese froyo sbf is intended only for different DEFY (ME525) / Chinese Defy, and normal Defy is MB525.
it could damage your flashlight and phone.
use sbf from central europe froyo for best result installing CM7.
thanks guys, I charged the battery, got rsdlite to recognize the phone, and flashed a UK sbf, now its back on, working, and showing that motoblur animation.
I guess now all that's left is to install a 2.1 OS and everything should work.
(Please correct if I got this wrong, since I AM a noob and i really don't want to make another mistake)
THANKS ALOT!
If you flashed a full Froyo SBF then you cannot install Eclair SBF. It's not possible to directly downgrade after you have flashed Froyo using a full SBF. However you can easily flash a Froyo official ROM or... why not CM7 or MIUI.
Thing is... I already flashed 2.1, and got it to the point where it shows me the M logo. but it didn't go any further than that. i tried flashing a 2.3.3 ROM, same thing happens, M logo but nothing more. right now im back to this version of 2.2:
p3_jordan_umts_jordan-user-2.2.1-3.4.2-107_JDN-4-000000-release-keys-signed-T-Mobile-US.sbf
and I'm getting an animation of Motoblur with nothing else.
flaah nordic sbf then go to cm7. Follow the guide read first cm7 faq before proceeding
Sent from my MB525 using XDA App
All you do is flashing.. Have you actually do total wipe in recovery? Since you're having the motoblur animation splash screen, it is obviously your previous data is conflicting while the phone is trying to boot normally..
Sent from my awesome Moto Defy: Stock Rooted Gingerbread 2.3.3 - XDA Premium
farsight73 said:
All you do is flashing.. Have you actually do total wipe in recovery? Since you're having the motoblur animation splash screen, it is obviously your previous data is conflicting while the phone is trying to boot normally..
Sent from my awesome Moto Defy: Stock Rooted Gingerbread 2.3.3 - XDA Premium
Click to expand...
Click to collapse
I believe you are right about wiping, I've bricked my phone to the point i couldn't turn the phone on. So all you usually have to do is flash the full sbf, when it tries to boot it gets stuck on the m logo, just pull the battery, power it up holding volume down wait for the the triangle and press the middle of the volume rocker and it will take you to the stock recovery. Wipe and factory rest, flash the sbf again.
wipe/factory reset didn't fix it, though I noticed nordic sbf got it to show the android animation.
is it possible that I need to install a rom after I flash an sbf? and if so, how can I install a rom (custom recovery doesn't give me an option to install a zip, only "update.zip").
do I install some sort of 2ndinit?
do I install a rom through "update.zip"?
sorry once again for another (hopefully last ) noobish questions.
The SBF is a full ROM so atfer flashing a SBF there is no need to put another ROM via recovery, unless you want to do so (let's say you'd like to install CM7 or MIUI). If you haven't flashed a 2.3.4 full SBF you should be able to revive your Defy using the nordic SBF. Try to download it again or try a different one (one of those official SBF's released this summer).
I did install a 2.3.4 full sbf, but it too didnt work, tried a factory reset + cache wipe, and reflashing the 2.3.4 and it's still stuck on the M logo
Ive done something stupidly wrong.. Help me please..
Ok Ive a me525 and I tried to flash my phone with JRDNEM_U3_2.51.0_CHN_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA030.0R_USAJORDANRTINT_P029_A018_HWp3_Service1FF
Was not sure what I was doing at that moment(just following a guide/tutorial on YouTube)After the whole progress with RSD lite, my device turned black as the title says with only showing a white led light. Was getting pretty deperate thinking about I had broken the phone.. :crying:
I have searched for a solution on the forums saw some people did get their device repeared, but everything they had done didnt worked for me..
So please help this boy in need.. We dont have lots of money to spare so buying a new phone isnt really a fast option..
p.s. Not sure though but would a chinese sbf work and where would I find one?
Related
I'm not sure where to start, so if there's anything i left out, I'll be glad to clarify.
phone: Motorola Bravo MB520
stock: 2.2.1
current: CM7 V5
i made the mistake of pulling the battery during a clockwork restore from CM7 for Bravo to a rooted stock nandroid, then the battery died before completion, corrupting the flash.
i hotwired the phone, and flashed the above linked 2.2.1 SBF and did a factory reset, all caches wiped and the phone is alive!... kind of.
from this point on, the phone will start up while hotwired, but I get an error that the battery is not recognized as a genuine Motorola battery (it is), and there is a question mark in the battery indicator in status bar and in the charging startup screen (phone off, plug into wall, moto logo, battery charge image).
"/sys/class/power_supply/battery/uevent" reads:
POWER_SUPPLY_NAME=battery
POWER_SUPPLY_TYPE=Battery
POWER_SUPPLY_STATUS=Unknown
POWER_SUPPLY_HEALTH=Good
POWER_SUPPLY_PRESENT=0
POWER_SUPPLY_TECHNOLOGY=Li-ion
POWER_SUPPLY_CAPACITY=100
POWER_SUPPLY_VOLTAGE_NOW=3753000
POWER_SUPPLY_TEMP=340
POWER_SUPPLY_CHARGE_FULL_DESIGN=0
POWER_SUPPLY_CHARGE_COUNTER=100
I bought a new battery, same issue.
I baleted the contents of "/data/battd/" and "/data/system/batterystats.bin" with no change.
The battery is seated properly, with no corrosion on terminals.
Is there anything more than can be done?
Just for sh**'s and giggles did you try to do another flash with the 2.2.1 sbf? Might help. Or just try flashing the CM7 rom, turn it on and just play around a little then flash back to 2.2.1. Post an up date please! Others might do this too.
Junkyardjames87 said:
Just for sh**'s and giggles did you try to do another flash with the 2.2.1 sbf? Might help. Or just try flashing the CM7 rom, turn it on and just play around a little then flash back to 2.2.1. Post an up date please! Others might do this too.
Click to expand...
Click to collapse
i've flashed the 2.2.1 SBF 2-3 times now. after encountered this, that was my first thought, having been unable to get RSDLite to give me a success response. the only CM ROM's available are ports of the Moto Defy. This one just has the working cameras. Stock factory reset gives same error as does another CM port by rdanner/josuearisty as well as bandroidx's ROM.
Hi guys
Before I explain I'd like to say that yes, I have read other threads on similar topics, although none seem to have the same symptoms as me...
This week I bought a software-bricked Defy on eBay with the hopes of fixing it and giving it to a friend. I first tried flashing an old Eclair SBF to no avail (only switched on to bootloader) and thought that it could be failing due to it being on a newer firmware. So then I tried Froyo, and when that didn't work either (bootloops like when I received the phone) I thought my last resort was a CG 5 SBF, so I went for the JORDN_U3_97.21.51 build. This seems to get further into the booting process, with the MotoBLUR animation appearing but I get a BP Panic - 0x00080010 above the animation before the phone switches off. Thinking I had nothing to lose I tried a Gingerbread ROM, but that just bootlooped too so I went back to 97.21.51. I realise I've probably painted myself into a corner by flashing these
I'm all out of ideas with how to get the phone any further and have searched for the BP panic to no avail. I can get into stock recovery and bootloader, although the recovery seems to have issues with accessing the cache sometimes.
Thanks for reading
The same panic have y for the last 2 weeks, after flashing hangs in bootloader (red logo and no animation), after other flash hangs on a animated red logo and thats where you must give it time 3 or 4 min. wating, when its dont works you can try to pul out battery and do it in again while you hold the start and vol. down button, then in recovery menu wipe Dalvik cache and wipe cahe. Maby it works then, when not you can try like me to go again tho recovery and there restore stockrom, thats the way ym getting my defy work again. There are many ways to get it back to work again and it cost me 2 weeks after flashing maby 15 diverend roms to get it works and even than when it works, 2 days work whit rooting it and get 3G alive. So when you think its dead, maby RSDlite can bring it back to live, just like here.
Now my Defy MB525 working like a Defy 526 on Gingerbread.
So don't give up, when you can see whit RSDlite the phoon, it must be possible to get it work, only problem here was on a moment when the battery was empty, but here on XDA you can find the megayver method (charging on a ohter cell like a duo) or what y have don, get my old nokia loader (5V) and whit 2 wires hangs on the battery power it up to 4.1 V, succes.
Thanks, although I was just getting repeated boot loops rather than it hanging on the logo... And that wasn't animated either. How did you manage to restore the stock ROM through the recovery? Did you have a flashable zip? Please bear in mind that I did not get a custom recovery installed
I'll look out for the low battery problem. Thanks for your advice
ben_duder said:
Thanks, although I was just getting repeated boot loops rather than it hanging on the logo... And that wasn't animated either. How did you manage to restore the stock ROM through the recovery? Did you have a flashable zip? Please bear in mind that I did not get a custom recovery installed
I'll look out for the low battery problem. Thanks for your advice
Click to expand...
Click to collapse
U should have wiped cache and data after flashing Froyo!!!!!!
It would have booted!!!!
Now u flashed GB!! Ur stuck there!!!
Flash gb again and Go to stock recovery and wipe data!!!! If know how to do it!!!
Sent from my MB526 using xda premium
nogoodusername said:
U should have wiped cache and data after flashing Froyo!!!!!!
It would have booted!!!!
Now u flashed GB!! Ur stuck there!!!
Flash gb again and Go to stock recovery and wipe data!!!! If know how to do it!!!
Sent from my MB526 using xda premium
Click to expand...
Click to collapse
Thanks, although I'm pretty sure I did wipe cache and data... and I definitely did (several times ) after flashing Gingerbread. I feel like whatever is preventing Froyo and Gingerbread from booting is the same thing as what is giving me the BP panic on the CG 5 Eclair ROM.
I would suspect a hardware issue here.w
Sent from my MB525 using Tapatalk
I think it might be too It's a shame because I can enter recovery and bootloader okay, and the seller said it broke during a failed software update so I thought it would be a simple matter of reflashing an SBF.
what is bp panic?
what happens when it is booting?
Sent from my MB525 using xda premium
When I try to boot the CG 5 Eclair I get past the static Motorola logo (hence further than any other build) but the MotoBLUR animation is stuttery, with a BP panic at the top (see picture). This goes on for quite a while, then the phone switches off and this loops.
Ok if occurred during a software update, find out which he was installing and try that one. May also be worth trying motoupdate.
Sent from my MB525 using Tapatalk
I might try that, but won't it be useless now that I've flashed CG 5? I'll look into MotoUpdate
Is the general consensus that this is an unfixable hardware issue, then?
Apolgoies if you've already tried this, but I had a Defy which would do the same, either stuck on M logo or error in bootloader.
Each time I just plugged it into PC / USB at bootloader screen, and used RSD Lite to try another ROM. Eventually I found one which worked. I think I tried 5 before finding one which didn't cause any problems.
My defy was a ME525+ and the ROM which finally worked was "DEFYPLUS_U3_4.5.1-134_DFP-132_BLUR"
So, if you haven't already, I'd just suggest try a few more ROMS, flashed from Bootloader / RSD Lite.
Hope it helps somehow
Hello there, i recently got a Motorola defy and the first thing i did was install cm7. A few day later i noticed an issue with the charging port (the phone froze up and became unusable when i was using a wall charger) so i decided to return it to stock for warranty issues since i flashed to miui and the problem persisted. My phone company is Claro Dominican Republic so after doing some research i tried to put the Claro Argentina SBF using RDS lite, in paper that should have left the phone stock.
After installing that SBF the defy got stock in a boot loob, i got the motorola logo then some data usage warnings in spanish (just like the first time u boot the phone) but i kept restarting. I tried reflashing that same SBF but the problem persisted. I tried other things like installing a nordic sbf and whatnot and every time the same thing happened. Later i stubled upon a chinese sbf that did boot. I rooted the phone installed 2ndinit poped into recovery used the full wipe zip and tried to install cm7, there it got stuck at the google logo and i couldn't enter recovery.
I reflashed with the Chinese sbf re rooted and re did everything and i tried installing miui and i got the same issue. I also tried using an nandroid backup from Claro Argentina but nothing happened the phone stayed the same with the Chinese SBF.
Im fresh out of ideas and ive tried alot of things ive read arround but nothing has worked. Id love to hear your opinions on this issue, thanks in advanced
First what chinese sbf you flashed?? And second, before flashing stock again wipe data and cache on stock recovery.
Motorola Defy CM7 RC 1.5 OC 1GHz
JORDN_U3_97.21.51, thats the rom name its the only one thats working for me atm. Ive tried many things but i cant get any other rom to work.
Bad news, you cant downgrade that, now you are stuck on eclair or gb 2.3.4, cause jrdn_u3_97.21.51 has cg version 5, and froyo version 4, try this, flashing eclair again and then fixed froyo, whatever, i think motorola can see wich cg you are, wonder they not!!
forum.xda-developers.com/showpost.php?p=14762402&postcount=143
Good luck!
Motorola Defy CM7 RC 1.5 OC 1GHz
LeonardoJegigzem said:
forum.xda-developers.com/showpost.php?p=14762402&postcount=143
Click to expand...
Click to collapse
That link worked perfectly!, i had a problem with my phone internal memory (only had 128mb available) But i reinstalled the nandroid backup in the link did a factory reset there then i installed cm7 without any issues.
Now i still have the charging problem (my phone becomes unusable when its charging, gets super laggy). I want to return the phone to stock settings so that i can claim my warranty on it. Any ideas on how to put the sbf without getting the problem i had or should i just live with the issue?
You can only flash that fixed froyo of the link, because each sbf has a version, the chinese you flashed is version 5, and once you flash a new version you cannot then flash a lower one, here the problem, froyo is version 4, a fixed is a sbf without, cg31 and cg39 files
Motorola Defy CM7 RC 1.5 OC 1GHz
Cant i modify the sbf i want to install like the guy in the link did? and what about my charging problem, ever heard of it?
Yep, you can, but i never did it, i know you must use the SBF Depacker or something like that, and for the laggy try wiping cache and dalvik cache and see what happens!, did you wipe data when flashed CM9 over CM7??
yeah, and im using cm7. i wiped dalvik already and nothing.. it only happens when im charging the phone via the wall charger adapter
Hi,
I was running CM10 on my defy and then i tried to update it with Quarx latest build and something went wrong....i was stuck at the motorola logo screen....
I used RSD Lite V5.3.1 to flash the stock rom to my defy and it still wont boot....its still stuck at the motorola logo....
Please help.....its booting only under the Bootloader mode (Power+Vol Up).....nothing else
Thanks
Shrewdy said:
Hi,
I was running CM10 on my defy and then i tried to update it with Quarx latest build and something went wrong....i was stuck at the motorola logo screen....
I used RSD Lite V5.3.1 to flash the stock rom to my defy and it still wont boot....its still stuck at the motorola logo....
Please help.....its booting only under the Bootloader mode (Power+Vol Up).....nothing else
Thanks
Click to expand...
Click to collapse
Did you flash the correct sbf?
How long are you stuck at the Motorola logo? Give a bit more information =P
It's most likely not bricked as it's almost impossible to brick the defy.. (I've never heard of it)
Please help
pk92 said:
Did you flash the correct sbf?
How long are you stuck at the Motorola logo? Give a bit more information =P
It's most likely not bricked as it's almost impossible to brick the defy.. (I've never heard of it)
Click to expand...
Click to collapse
Hi,
First i had upgraded to froyo and and used this link to get Gingerbread on my defy
http://forum.xda-developers.com/showthread.php?t=1285007
After that i installed many roms and the last one to be tried was CM10...which started all the problems...
I have now tried to flash rom from this link
http://forum.xda-developers.com/showthread.php?t=1386942
now it is booting up but now it is stuck with the animation screen....the phone actually does not start....
i know its something to do with the kernel but then i dont know which type of kernel to flash and how!!
Please help..
Let me know if you need any more information
Thank you....
Shrewdy said:
Hi,
First i had upgraded to froyo and and used this link to get Gingerbread on my defy
http://forum.xda-developers.com/showthread.php?t=1285007
After that i installed many roms and the last one to be tried was CM10...which started all the problems...
I have now tried to flash rom from this link
http://forum.xda-developers.com/showthread.php?t=1386942
now it is booting up but now it is stuck with the animation screen....the phone actually does not start....
i know its something to do with the kernel but then i dont know which type of kernel to flash and how!!
Please help..
Let me know if you need any more information
Thank you....
Click to expand...
Click to collapse
Red or Green Lens? Defy or Defy+?
If Red Lens then you can use Defy or Defy+ build straight from Froyo after installing 2nd init.
If Red Lens Defy with Defy+ build, you will need a battery fix
If Red Lens Defy with Defy build, nothing else needs to be installed
If Green Lens Defy, you can only use Defy build. Nothing else needs to be installed.
If Defy+ You can only use defy build, nothing else needs to be installed.
Download the defy/defy+ builds here:
http://forum.xda-developers.com/showthread.php?t=1768702
http://quarx2k.ru
There is also an SBF of CM10 here: http://forum.xda-developers.com/showthread.php?t=1691901
Thanks buddy
pk92 said:
Red or Green Lens? Defy or Defy+?
If Red Lens then you can use Defy or Defy+ build straight from Froyo after installing 2nd init.
If Red Lens Defy with Defy+ build, you will need a battery fix
If Red Lens Defy with Defy build, nothing else needs to be installed
If Green Lens Defy, you can only use Defy build. Nothing else needs to be installed.
If Defy+ You can only use defy build, nothing else needs to be installed.
Download the defy/defy+ builds here:
http://forum.xda-developers.com/showthread.php?t=1768702
http://quarx2k.ru
There is also an SBF of CM10 here: http://forum.xda-developers.com/showthread.php?t=1691901
Click to expand...
Click to collapse
i am downloading the CM10 sbf's for both Froyo and GB..
i will try to install each and will see which ones works for me....
Coz i have a defy and i think it is a red lense one.
But i had a GB kernel running on my defy....
I hope thinks get well with my defy....
Thanks, will update you as soon as something happens....
Nothing works
Shrewdy said:
i am downloading the CM10 sbf's for both Froyo and GB..
i will try to install each and will see which ones works for me....
Coz i have a defy and i think it is a red lense one.
But i had a GB kernel running on my defy....
I hope thinks get well with my defy....
Thanks, will update you as soon as something happens....
Click to expand...
Click to collapse
----------------
All hopes going down... I have flashed these sbf's from the link your provided but nothing works !!
1. Froyo-cm-10,JB.Quarx.30.07.build.Defyred/green.bl4.fixed'sbf NEW
2. A.2.3.6-cm-10,JB.Quarx-30.07build-Defy+/red fixed'sbf cm-10 bootanimation New
Infact i get an error at the bootloader itself Err: A5,70,00,00,23 (wonder whats that)
There is only 1 sbf that boots it up....but then my defy keep looping on the blur animation and never boots up....
SBF that works the most i got it from here
http://forum.xda-developers.com/showthread.php?t=966537
which was (4.5.1-134-DFP-1321 - retail-asia full Blur multilanguage Thread)
This works and atleast it sort of tries to boot up....
Also if i try to get into the recovery mode (Power + Vol Down)....i cannot see any options in recovery....just the small android exclamation image !!
Can you please help and get me atleast booted up till recovery ??
Thanks
Shrewdy said:
----------------
All hopes going down... I have flashed these sbf's from the link your provided but nothing works !!
1. Froyo-cm-10,JB.Quarx.30.07.build.Defyred/green.bl4.fixed'sbf NEW
2. A.2.3.6-cm-10,JB.Quarx-30.07build-Defy+/red fixed'sbf cm-10 bootanimation New
Infact i get an error at the bootloader itself Err: A5,70,00,00,23 (wonder whats that)
There is only 1 sbf that boots it up....but then my defy keep looping on the blur animation and never boots up....
SBF that works the most i got it from here
http://forum.xda-developers.com/showthread.php?t=966537
which was (4.5.1-134-DFP-1321 - retail-asia full Blur multilanguage Thread)
This works and atleast it sort of tries to boot up....
Also if i try to get into the recovery mode (Power + Vol Down)....i cannot see any options in recovery....just the small android exclamation image !!
Can you please help and get me atleast booted up till recovery ??
Thanks
Click to expand...
Click to collapse
I believe that little android guy is the stock recovery. From what I remember you hold both volume buttons and it takes you into stock recovery.
Unfortunately, you will no longer have 2nd init installed, which allows for CWM recovery, so you can't flash a zip from there.
How long does it stay stuck on the blur logo? Maybe you're just not waiting long enough? (Stupid question I know, but some people complain after 2 minutes, the first boot can take a long time!)
Try looking at This thread and see if the link which is in this post will work to download the Taiwanese SBF. For me it doesn't seem to load
Edit: - Oh the Taiwanese SBF did eventually download. Took about 5 minutes with the tab open loading. I've uploaded it to my Dropbox so you can download from there... should be a bit faster!
JRDNEM_U3_3.4.3-33-1_CHINESE_SIGN_SIGNED_UCAJRDNEMARAB1B50AA03A.0R_PDS03C_USAJRDNFRYORTINT15_P001_A013_HWp3_Service1FF.sbf.gz
(MD5 - 34E9A43EAB8D2FF6101536C4B3F104BD)
Note: This is Taiwanese, NOT CHINESE. The Chinese one burns out the flashlight and it cannot be used after that.
Still stuck
pk92 said:
I believe that little android guy is the stock recovery. From what I remember you hold both volume buttons and it takes you into stock recovery.
Unfortunately, you will no longer have 2nd init installed, which allows for CWM recovery, so you can't flash a zip from there.
How long does it stay stuck on the blur logo? Maybe you're just not waiting long enough? (Stupid question I know, but some people complain after 2 minutes, the first boot can take a long time!)
Try looking at This thread and see if the link which is in this post will work to download the Taiwanese SBF. For me it doesn't seem to load
Edit: - Oh the Taiwanese SBF did eventually download. Took about 5 minutes with the tab open loading. I've uploaded it to my Dropbox so you can download from there... should be a bit faster!
JRDNEM_U3_3.4.3-33-1_CHINESE_SIGN_SIGNED_UCAJRDNEMARAB1B50AA03A.0R_PDS03C_USAJRDNFRYORTINT15_P001_A013_HWp3_Service1FF.sbf.gz
(MD5 - 34E9A43EAB8D2FF6101536C4B3F104BD)
Note: This is Taiwanese, NOT CHINESE. The Chinese one burns out the flashlight and it cannot be used after that.
Click to expand...
Click to collapse
Thanks for helping me out....
The motorola logo stays around for 20 seconds after with the Motorola boot animation starts.....
So i left my defy on for around 20 mins and nothing is happening its still playing the boot animation. !!
I havent yet downloaded the sbf link you have given me as i am at work now and will be able to do that only when i reach home.
Another thing i have noticed is that i am able to charge my defy....that means the rom is present and hopefully working !!
What say....???
Have you done Factory Reset????
1- turn off your phone (take the battery out and then put it back in)
2- press and HOLD the volume DOWN button + power button
3- Motorola logo appears first, then after a few seconds an 'android ROBOT logo' appears
4- press volume UP and DOWN buttons at once, quickly
5- from the menu choose 'factory reset/wipe-format data'
6- then do 'wipe cache'
7- then do a reboot
see if it helps and you are able to start the phone normally
Euro your awesome!!
Euro_Rules said:
Have you done Factory Reset????
1- turn off your phone (take the battery out and then put it back in)
2- press and HOLD the volume DOWN button + power button
3- Motorola logo appears first, then after a few seconds an 'android ROBOT logo' appears
4- press volume UP and DOWN buttons at once, quickly
5- from the menu choose 'factory reset/wipe-format data'
6- then do 'wipe cache'
7- then do a reboot
see if it helps and you are able to start the phone normally
Click to expand...
Click to collapse
Hi buddy,
Thanks yaar...i did exactly you told me to and the phone booted normally...
thanks a million buddy...:good::good:
And i also owe a million thanks to pk92...you have been there when i need you the most buddy....:good::good::good:
Thanks...m so happy to see my defy come back to life... :laugh::laugh::laugh::laugh:
O god!! its been a tough time but i learnt something new too....
Thanks guys :laugh:
friend request !!
hi, pk92 & euro
i have sent you friend request...do accept if you like !!
Thanks guys...
Shrewdy said:
Hi buddy,
Thanks yaar...i did exactly you told me to and the phone booted normally...
thanks a million buddy...:good::good:
And i also owe a million thanks to pk92...you have been there when i need you the most buddy....:good::good::good:
Thanks...m so happy to see my defy come back to life... :laugh::laugh::laugh::laugh:
O god!! its been a tough time but i learnt something new too....
Thanks guys :laugh:
Click to expand...
Click to collapse
Hehehehehehehehe
You are Welcom Shrewdy
Say thanks to our awesome XDA developer's Because of them we are nothing...
Shrewdy said:
hi, pk92 & euro
i have sent you friend request...do accept if you like !!
Thanks guys...
Click to expand...
Click to collapse
Accepted :highfive:
Guys I have the same problem.
Phone was upgraded from Froyo to CM7 and took it fine. Played for a while in CM7 but decided to upgrade to CM10.
Followed the steps from this thread http://forum.xda-developers.com/showthread.php?t=1795647
flashed foryo Kernel
Flashed CM10-20120924-NIGHTLY-mb525.zip
Flashed Google apps
Cleared cache, cleared Dalvik
Phone boots but gets stuck at Motorola logo and after blue and green light it loops back again to the same sequence.
It's a Defy with green lens and it had stock T-Mobile Froyo (rooted) before flash to CM7.
I'm now back to CM7 as CM10 didn't want to work.
sorry didnt get you
czarekusa said:
Guys I have the same problem.
Phone was upgraded from Froyo to CM7 and took it fine. Played for a while in CM7 but decided to upgrade to CM10.
Followed the steps from this thread http://forum.xda-developers.com/showthread.php?t=1795647
flashed foryo Kernel
Flashed CM10-20120924-NIGHTLY-mb525.zip
Flashed Google apps
Cleared cache, cleared Dalvik
Phone boots but gets stuck at Motorola logo and after blue and green light it loops back again to the same sequence.
It's a Defy with green lens and it had stock T-Mobile Froyo (rooted) before flash to CM7.
I'm now back to CM7 as CM10 didn't want to work.
Click to expand...
Click to collapse
hey buddy...m sorry i didnt quite get you....
As per my understanding i believe your phone is working fine with CM7 installed and you want to install CM10 on your defy !!
am i correct !!
if you then let me make it clear that the latest CM10 build used a custom kernel made by quarx himself....it is not running a froyo or gb kernel...
so here is what you need to do....
1. simply factory reset your phone...clear cache and dalvik...
2. now flash the latest CM10 build
3. again...clear cache and dalvik...
4. and now let defy boot....first boot may take a longer time....
hope this works for u...if it does not...let me know...will b glad to help u...
Thanks
Shrewdy said:
hey buddy...m sorry i didnt quite get you....
As per my understanding i believe your phone is working fine with CM7 installed and you want to install CM10 on your defy !!
am i correct !!
if you then let me make it clear that the latest CM10 build used a custom kernel made by quarx himself....it is not running a froyo or gb kernel...
so here is what you need to do....
1. simply factory reset your phone...clear cache and dalvik...
2. now flash the latest CM10 build
3. again...clear cache and dalvik...
4. and now let defy boot....first boot may take a longer time....
hope this works for u...if it does not...let me know...will b glad to help u...
Thanks
Click to expand...
Click to collapse
Yes, you are correct. the phone is working fine with CM7.
Factory reset, you mean from boot menu or the hard factory reset with holding volume keys (procedure posted above in this thread)?
The first time I actually tried, I did flash of CM10 without the prior kernel flash and it didn't work either.
so do I need any kernel flash or do I just flash it with CM10 and it should work?
I'll try again later today or tomorrow.
Thanks
czarekusa said:
Yes, you are correct. the phone is working fine with CM7.
Factory reset, you mean from boot menu or the hard factory reset with holding volume keys (procedure posted above in this thread)?
The first time I actually tried, I did flash of CM10 without the prior kernel flash and it didn't work either.
so do I need any kernel flash or do I just flash it with CM10 and it should work?
I'll try again later today or tomorrow.
Thanks
Click to expand...
Click to collapse
Lots of us who had bootloops trying to flash CM10 24/09 with a BL5 base SBF solved the problem by flashing a BL6 base Froyo SBF.
But try a factory reset and flashing your stock T-Mobile Froyo first.
If your stock doesn't flash properly then it means you have inadvertently flashed something which updated your BL version to BL5.
I flashed the JDGC_U6.2.13.0 SBF which is BL6 and then I was fine.
Don't use this ROM though, just use it as a stepping-stone to install CM10.
Euro_Rules said:
Have you done Factory Reset????
1- turn off your phone (take the battery out and then put it back in)
2- press and HOLD the volume DOWN button + power button
3- Motorola logo appears first, then after a few seconds an 'android ROBOT logo' appears
4- press volume UP and DOWN buttons at once, quickly
5- from the menu choose 'factory reset/wipe-format data'
6- then do 'wipe cache'
7- then do a reboot
see if it helps and you are able to start the phone normally
Click to expand...
Click to collapse
Thanks a lottt.. :highfive:
Hi all
So, I have a problem with my Defy (MB525 green lens). The best will be, if I'll write my full story. Here is it:
Story
I had Defy with CM 10. It had bloated battery. I wasn't using it for 6 months because I have another phone.
Some time ago, I decided, that I'll give Defy to my grandfather. On Tuesday this week I bought new original battery. I put it in the Defy, and charge it. I could boot up my old system as I wrote, CM 10. While it was charging, I detected that I haven't got SD Card. On the other hand, I found some 4GB Samsung SD, which had my father in his Desire. The SD Card had 3 partitions, which I tried to delete, and make only one, with GParted. After I did it, Linux and Windows can't see it. (This is almost other problem, which I'm trying to solve here http://crunchbang.org/forums/viewtopic.php?pid=350683)
But, when I put the CD Card to Defy, in TWRP recovery I could see some strange symbols. I thought, that I can repair something when I wipe SD Card. When the battery charged, I decided to do factory reset and wipe SD card. Here is my first failure. In TWRP I went to custom wipe, and here I marked everything including system and I wiped it. Then I remembered that system is recovery too. TWRP wrote, that everything except SD-Ext and SD was wiped. I known that this will be a problem. Yes, after reboot only Motorola logo without recovery.
I think, there was only one option - flash SBF, which I did. I went to stock bootloader and with sbf flash in Linux, I flashed this:
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF.sbf
And than this:
CM7RC1.5_16_09_11_custom.sbf
After reboot, I got bootloop. I tried to replace battery, do factory reset but nothing helped. That time I haven't got working card, so I couldn't flash some zip via CWM recovery. Thus, I again flash another SBF, but I don't really remember which. Probably some official CEE Froyo however, I'm not sure.
After that and reboot, I got only black screen with white led lighting while USB was connected. When I wanted to go to stock bootloader, still black screen, but I can flash SBF, and while flashing, screen have brightness and text about flashing.
I knew that this is little hard brick. I again tried to flash other SBF which I have or I downloaded (yes, again I don't know which). One of SBFs which I flashed was some fixed Chinese SBF . That made my defy booting, screen working, but still bootlooping. I couldn't reach any recovery.
Again, I flashed other SBFs, CM's too but nothing worked and I got black screen again.
And this was end of my story.
Current situation
I have Defy (MB525 green lens), with unknown framework an it had only black screen and what only I can do, is break Defy with hammer or flash some SBF.
So, here is list of all SBF files, that I have downloaded and probably tried to flash: (No order)
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF.sbf
CM7RC1.5_16_09_11_custom.sbf
JRDNEM_U3_2.51.1_BLUR_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA030.0R_USAJORDANO2DE_P048_A015_HWp3_Service1FF.sbf
JRDNEM_U3_3.4.2_177-003_BLUR_SIGN_SIGNED_USAJRDNEMARAB1B8RTGB03A.0R_PDS03C_USAJRDNFRYORTGB_P019_A010_HWp3_Service1FF.sbf
DFPRC_U_4.5.3-109_DPP-6-7_SIGNED_USADEFYPRCB1B50AA00A.0R_JRDNGIBRRTGC_P025_A019_HWp3a_Service1FF.sbf
JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF.sbf
JORDN_U3_97.21.51.sbf
JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P011_A010_HWp3_Service1FF.sbf
4.5.1-134-DFP-132-gingerbread-BL6-fixed.sbf
4.5.2-109-DHT-22-gingerbread-BL5-fixed.sbf
3.4.2-177-003-nordic-froyo-fixed.sbf
3.4.2-179-002-tmobile-froyo-fixed.sbf
4.5.1-134-DFP-74-gingerbread-BL5-fixed.sbf
4.5.3-109-DPP-11-gingerbread-BL5-fixed.sbf
JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN.sbf
Probably that is all what I have.
I've read many topics with similar problem and guides, but nothing helped me, or SBFs were unavailable.
So, what have I to flash, or which guide to try, if I want working Defy?
Sorry for my not good English
Thanks
UPDATE
sterver1 said:
Wohooo!!
Story
After a long time (4 months)...
Accidentally today I found my favorite custom ROM - MoKee OS, for Defy. I said to myself: "Hm, I have some time... I'll try to flash this MoKee on my Defy and maybe it solve my problem with (not) charging/unknown battery for system."
I picked out box with Defy from drawer, wiped the dust, took the Defy and said: "Sh*t! I haven't got SD Card!" Fortunately I found one. I download MoKee OS zip on that SD Card, put it to Defy, booted to recovery and flash MoKee OS zip. (...with full wipe of course...) Then rebooted to system.
Uselessly. Still unknown battery. "Hmm, It doesn't matter. Maybe here are some new stuffs which can solve my problem." And I continued to finding something, that can solve my problem. After a while I found ROMs with new 3.0 Kernel by Quarx. HERE. I downloaded CM 11 EXPERIMENTAL with this kernel and update recovery and flashed them. I didn't read thread. After reboot system didn't boot up and TWRP was inaccessible. I found why when I read some posts from that thread. HERE. But I couldn't flash that zip via recovery because I couldn't open recovery. So I mount /system to USB from bootloader and added files from zip manually to /system partition. After reboot it jammed on booting up. But TWRP was accessible so I did full wipe and flashed CM 11 EXPERIMENTAL and than that fix zip by @lorcotti. After that it finally booted up and battery was working and charging!
And they all lived happily ever after. :laugh:
SO, If you have some problem as me (unknown battery after flashing GB SBF on MB525), try this:
1. Download recovery and some ROM from [Kernel][GPL] Development 3.0 Kernel and fix from this post.
2. Put all zips on your SD Card.
3. Boot up to recovery.
4. Flash update-recovery.zip.
5. Reboot to recovery.
6. Do full wipe.
7. Flash ROM with 3.0 Kernel.
8. Flash Fix.
9. Wipe cache and dalvik cache.
10. Reboot to system.
If you want, you can flash GAPPS via recovery too.
But this will not be for daily usage! 3.0 Kernel by Quarx have a lot of bugs!
Thanks all!
Click to expand...
Click to collapse
Yeah!
Today I again tried to flash chines SBF. This one: JDGC_U6_2.13.0 China Unicom Thread/Download !!!BL6 kernel !!!
JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF.sbf
...and now I have bootable phone . I read many topics again and I got to know how to aces stock recovery. So I made wipe on this chines ROM and I can boot without loop, but I can only do emergency call with SIM it is the same. So, now, I don't know, what have I to do/flash, how to root it and flash here custom rom. Can I use SuperOneClick if it probably haven't got turned on USD Debugging?
Back on black
So, I made sbf file with depacker...
CMG39 from JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P011_A010_HWp3_Service1FF
and all others from JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF except CMG31.
Than the bootscreen changed from chines logo to grey motorola logo and I got Bootloader (9.00) Error A5,70,39,00,27. After that I flashed another sbf and I got Error A5,70,00,00,23. Than I flashed DEFYPLUS_U3_4.5.1-134_DFP-231_CEE_ROOTED_No_Signed.sbf and now I again have only black screen. F*ck!
I tried to flash my made sbf and chines one (JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF) too but nothing...
Really here is nobody who can help please??? I want give Defy as Christmas gift. :crying:
OK, so repetition.
What mistakes I've made
1. I wipe wipe all including system partition in TWRP without any flashable zip on SD card.
2. I continued with flashing original SBF, while I have usable CWM.
3. I flashed many no downgradable GB SBFs.
4. I flashed Defy Plus SBF on Defy.
I hope that there is still hope.
Somehow to downgrade, flash only CWM where I can flash nandroid backup or I don't know what else...
a gingerbread sbf should also work on green lens defy as there is no diff. in hw... instead the cam
have you tried a factory reset in stock recovery after sbf flash ?
Sent from my MB526 using xda app-developers app
Now, after all (which I tried) SBFs I get only black screen. I tried many GB SBFs too, but still black screen...
I'm going to try some another Poland SBFs and than if that won't work, I'll try to flash all in Froyo CEE SBF particularly.
Thanks for your response.
Once you've flashed GB stock sbf you can't go back staight to froyo or else
Read the beginners guide and the SBF matrix sektion carefully.. if you haven't...
Sent from my MB526 using xda app-developers app
DFP 231 has been flashed by you, so no froyo sbf will work. Black screen on dfp 231 indicates some eMMC problem, because bl version is highest(no error possible). IMHO only service centre can disable bl check or replace the main board to fix the problem
The problem should have been solved at the boot loop issue by wiping from stock recovery, no network solved by baseband/radio fixes. Check the rsdlite log file to confirm checksum/access errors. I think that the custom sbf somehow messed up either eMMC or efuse(less likely, unheard of).
For sdcard error wipe everything using hdd llf. If any error persists it's a hardware issue
Sent from my MB526 using Tapatalk 4
@bone101
I know, I read it few times, and I know how it is (not) working. But, after all GB SBFs I got only black screen, so maybe were not correctly flashed... I'm using Linux and here is sbf_flash for flashing SBFs, and in it I can't view informations about phone as in RSD Lite... But maybe, it will work in wine..
Do you now, that if I flashed GB SBF, I have to flash another GB to solve my problem, because no Froyo will work?
@thekguy
I know how I can solve others problems. Only what I need help to solve is black screen.
Can't I flash something which support that high BL or it won't work?
check if you get into Bl. modus
press vol. up & then power button
tell what you see
Sent from my MB526 using xda app-developers app
That's what I'm saying, the black screen problem occurs due to bl version mostly, and you have highest bl, so in theory black screen is impossible. Unfortunately I have never seen in this forum any defy recovering from black screen after flashing dfp231. Check rsd log from windows if possible. Froyo sbf cannot work under any circumstance. You must flash only gb sbf
Sent from my MB526 using Tapatalk 4
@bone101
When I acess bootloader I have only black screen... While flashing I can see
"SW Update
In progress.."
Ok, I have Windows notebook available... Here are device properites from RSD Lite:
IMEI/ESN/MEID: N / A
Technology: N / A
Software Version: N / A
Flex Version: N / A
Bootloader Version: v0x000910
DRM Version: N / A
AP Die ID: 173002052f066b010000dcff0200
BP Die ID: 0000000000000000000000000000
AP Public ID: d0d8842b4879dd27b9eb94f970fbeec252fcb2f4
BP Public ID: 0000000000000000000000000000000000000000
Click to expand...
Click to collapse
I'm going to try some GB SBFs here...
WOHOOO I've got it! I flashed 231_GR_SIGN_UCADEFYEMARAB1B80AA004.0R_PDS03C_USAJRDNGIBRRTCEE_P022_A022_Service1FF.sbf and now I have got bootable phone... I'm in the system. I'm going to root it and flash CWM and MIUI if it will work.
Really thanks for your help!
sterver1 said:
@bone101
When I acess bootloader I have only black screen... While flashing I can see
"SW Update
In progress.."
Ok, I have Windows notebook available... Here are device properites from RSD Lite:
I'm going to try some GB SBFs here...
WOHOOO I've got it! I flashed 231_GR_SIGN_UCADEFYEMARAB1B80AA004.0R_PDS03C_USAJRDNGIBRRTCEE_P022_A022_Service1FF.sbf and now I have got bootable phone... I'm in the system. I'm going to root it and flash CWM and MIUI if it will work.
Really thanks for your help!
Click to expand...
Click to collapse
I'm stuck in same problem, downloading this sbf you mention before, hope it works. Fu^kin defy, it sucks
@Alejandrissimo
Good luck...
I have another problem. Now, I have GB kernel. In original 2.3.6 GB on MB525 green camera don't work, and battery too. So, I thought that, when I flash Froyo kernel (CM) and CM7 I got back Froyo kernel and working camera and battery. Yes, this was not possible. After I did it and rebooted it I got Bootloader error. I flashed DFP-231 again. Worked.
Than I tried restore Froyo from nandroid which I found something here on forum. Than I flashed CM7 and bootloader error again.
Now I have CM7 by Maniac for defy plus which worked well except camera and battery... I know that here are many topics about downgrading, camera fixing and others but all which I read are bad in something for me...
Here are some options what I found but I don't know if I can use one:
Method 2: (BIG thanks to Jebrew again for this one)
NOTE: You are going to need CM7 for this one. CM7 Stable version recommended.
Click to expand...
Click to collapse
from http://forum.xda-developers.com/showthread.php?t=1216982
DOWNGRADE
If you come from Android 2.1 and never flashed Android 2.2 you can use the fixed sbf-files method. With this method you will have a option to downgrade to you personal stock Android 2.1 via direct sbf flash.
Click to expand...
Click to collapse
from http://forum.xda-developers.com/showthread.php?t=966537 but I'v ever flashed Android 2.2.
Or http://forum.xda-developers.com/showthread.php?t=1465436 ... This is better option but I have flashed full 2.3.6 SBF and here is:
It will only work if you never flashed a Android 2.3.6 full sbf.
Click to expand...
Click to collapse
So, how can I downgrade or repair battery and camera? I don't care whether I have got GB or Froyo kernel if I have working camera and battery.
have you tried cm11 ?
or ms2ginger by walter79
Sent from my MB526 using xda app-developers app
sterver1 said:
@Alejandrissimo
Good luck...
Click to expand...
Click to collapse
Working and rooted, thanks for your help
Alejandrissimo said:
Working and rooted, thanks for your help
Click to expand...
Click to collapse
please see your PN
sterver1 said:
@Alejandrissimo
Good luck...
I have another problem. Now, I have GB kernel. In original 2.3.6 GB on MB525 green camera don't work, and battery too. So, I thought that, when I flash Froyo kernel (CM) and CM7 I got back Froyo kernel and working camera and battery. Yes, this was not possible. After I did it and rebooted it I got Bootloader error. I flashed DFP-231 again. Worked.
Than I tried restore Froyo from nandroid which I found something here on forum. Than I flashed CM7 and bootloader error again.
Now I have CM7 by Maniac for defy plus which worked well except camera and battery... I know that here are many topics about downgrading, camera fixing and others but all which I read are bad in something for me...
Here are some options what I found but I don't know if I can use one:
from http://forum.xda-developers.com/showthread.php?t=1216982
from http://forum.xda-developers.com/showthread.php?t=966537 but I'v ever flashed Android 2.2.
Or http://forum.xda-developers.com/showthread.php?t=1465436 ... This is better option but I have flashed full 2.3.6 SBF and here is:
So, how can I downgrade or repair battery and camera? I don't care whether I have got GB or Froyo kernel if I have working camera and battery.
Click to expand...
Click to collapse
Congrats man! Seems that rsdlite on Windows is the most reliable solution. Now to fix everything just flash cm10 (jelly bean) or later rom. It includes fixes for camera and battery
Again, no downgrading bl(not even jtag will work)
Sent from my MB526 using Tapatalk 4
Oh, ok. I'll try it. Thanks.
Hmm, and than, can I flash CM7 by Maniac or JB/GB WIUI and fixes in CM10 will still working?
Ms2ginger is not good for me because it haven't got slovak language. I'll give defy to my grandfather.
//And now, in Quarx CM 10 my battery don't charge. I tried 2 chargers and charging via USB too.
In options, battery is still "60% - Unknown"
Alejandrissimo said:
Working and rooted, thanks for your help
Click to expand...
Click to collapse
Hehe, I'm glad...
sterver1 said:
Oh, ok. I'll try it. Thanks.
Hmm, and than, can I flash CM7 by Maniac or JB/GB WIUI and fixes in CM10 will still working?
Ms2ginger is not good for me because it haven't got slovak language. I'll give defy to my grandfather.
//And now, in Quarx CM 10 my battery don't charge. I tried 2 chargers and charging via USB too.
In options, battery is still "60% - Unknown"
Hehe, I'm glad...
Click to expand...
Click to collapse
There's a cm7 2ndboot build which should work for you. Try cm10.1 or above, problem should be solved.
JB wiui includes those fixes, as does cm7 2ndboot. I don't think that wiui GB has them. I would personally go for cm10.1 or above
Sent from my MB526 using Tapatalk 4