Hello, I have a rooted Droid Pro, 2.3.4 with 4.7.3 XT610 Kernal. I have tried installing CM7 and CM9 and I always get the message E signature verification failed. Can anyone please help.
You cannot install cm7 or cm9 with stock recovery. You need to install clockworkmod recovery.
Many Thanks, but one question
rongsang said:
You cannot install cm7 or cm9 with stock recovery. You need to install clockworkmod recovery.
Click to expand...
Click to collapse
Installing was a success, but now the Mobile Network is not available. What should I do?
which rom?
CM9
rongsang said:
which rom?
Click to expand...
Click to collapse
I installed CM9 V2
gsm or cdma? what exactly is happening?
gsm
rongsang said:
gsm or cdma? what exactly is happening?
Click to expand...
Click to collapse
I can't make a call when i try it say mobile network not available. when i get on my browser it turns off after about 10 seconds. i have check airplane mode, made sure i am on wcdma.
Related
I have Clockworkmod installed and now that ice cream sandwich is finally out I want to upgrade my a500. Can someone point me to right firmware and directions.
I guess I need new boot loader installed also.
tritron777 said:
I have Clockworkmod installed and now that ice cream sandwich is finally out I want to upgrade my a500. Can someone point me to right firmware and directions.
I guess I need new boot loader installed also.
Click to expand...
Click to collapse
You will want to upgrade your bootloader first for sure. Most roms are going to not work with the Honeycomb bootloader in the near future. Go ahead and put version 7 of the bootloader on, so future bootloader enhancements can be flashed via CWM. Once you install the bootloader, install CWM again, pick a rom & enjoy! Test drive them all.
read the afterota thread in dev section download the software, as easy as 1-2-3 and your pretty much done , I dont know if he has V7 listed now , if not Civato has it!
Attantion
To upgrade to tegraowners ICS ROM or FLEXREAPER (not extrem vetsion) is no new bootloader needed!
I'm using both ROM with my stock HC bootloadet!
You can upgrade the bootloader later if you like.
m.
meduza2 said:
To upgrade to tegraowners ICS ROM or FLEXREAPER (not extrem vetsion) is no new bootloader needed!
I'm using both ROM with my stock HC bootloadet!
You can upgrade the bootloader later if you like.
m.
Click to expand...
Click to collapse
Really?
I have 4.0.3 and have just rooted.
I have downloaded tegraowners ICS to my sd and the latest galls.
Are you saying i can just boot and do the power + vol deal to install this rom and keep my bootloader stock?
Yes! But if it is the newst tegraowners ICS recovery 1.7.3 is required.
m.
meduza2 said:
Yes! But if it is the newst tegraowners ICS recovery 1.7.3 is required.
m.
Click to expand...
Click to collapse
Can I install 1.7.3 with Acer recovery installer?
No! Only a basic version but with that you can flash then 1.7.3.
m.
meduza2 said:
No! Only a basic version but with that you can flash then 1.7.3.
m.
Click to expand...
Click to collapse
So.... you mean i can use ari to install an older ver of clockwork and then with that i can install 1.7.3?
OldGaf said:
So.... you mean i can use ari to install an older ver of clockwork and then with that i can install 1.7.3?
Click to expand...
Click to collapse
Exactly..
Yes!
m.
OldGaf said:
So.... you mean i can use ari to install an older ver of clockwork and then with that i can install 1.7.3?
Click to expand...
Click to collapse
Sigh..... OK..... I tried 1.3.4 but now when I try to enter recovery I get "recovery verified failed" in red and I am unable to get the old one back.
I am running the ota ics 4.0.3 with 0.03.12-ics bootloader.
This was rooted with thund3r's method.
1. Which ver of cwm should i install with ari so I can then install touch 1.7.3
2. Is there anything I am not doing that i need to?
3. Is there a stock one I can download and install with Ari if I need it back?
Try the afterota tool http://forum.xda-developers.com/showthread.php?t=1675939, you can manually select the recovery you want and upgrade the bootloader if you need to. It's very easy to use.
lowsum said:
Try the afterota tool http://forum.xda-developers.com/showthread.php?t=1675939, you can manually select the recovery you want and upgrade the bootloader if you need to. It's very easy to use.
Click to expand...
Click to collapse
Sigh... there is only the light ver available for that now which is for info only.... and that crashed while gathering info.
Disable antivirus and user control on PC!
m.
meduza2 said:
Disable antivirus and user control on PC!
m.
Click to expand...
Click to collapse
Ya was thinking that... but no point with light ver as it does not actually do anything.... info only.
Hope the full version is back soon..... don't like loosing....
meduza2 said:
Disable antivirus and user control on PC!
m.
Click to expand...
Click to collapse
OK... All is good now and am running FLEXREAPER-RF1-EXTREME-EDITION_rv3 !!!
Thanks a so much for your help!
I picked this ROM as my first as it is same kernel and there are not many issues. May go to Tegraowners once issues are not as many.
Thanks again!
-OG-
Please use the Q&A Forum for questions &
Read the Forum Rules Ref Posting
Thanks ✟
Moving to Q&A
Hi all,
i hava i9505 with CWM and i'm trying to flash cm10.1 on my phone without luck, i'm always getting status 7 error.
i double checked the rom i downloaded and this is the correct rom.
what can i do and why is this happaning?
thanks!
elibenmo said:
Hi all,
i hava i9505 with CWM and i'm trying to flash cm10.1 on my phone without luck, i'm always getting status 7 error.
i double checked the rom i downloaded and this is the correct rom.
what can i do and why is this happaning?
thanks!
Click to expand...
Click to collapse
This is a known issue...
Please check this : http://forum.xda-developers.com/showthread.php?t=2296266&page=29
kaalalto said:
This is a known issue...
Please check this : http://forum.xda-developers.com/showthread.php?t=2296266&page=29
Click to expand...
Click to collapse
i still didn't understand if the problem fixed or not.
elibenmo said:
i still didn't understand if the problem fixed or not.
Click to expand...
Click to collapse
Yes, you can use last editions of Clockworkmod, Philz Touch or TWRP...
For my needs, I've chosen the official ClockWorkMod 6.0.3.3 because it supports CM auto update with no error at all.
Hi,
This is the first time I've tried rooting a device so bare with me :good:.
It's taken me a few attempt to get things working on my Defy MB525 I've managed to root it with SuperOneClick and install either CWM 2.5.1.8 or SndInit2.3 (which uses CyanogenDefy Recovery v5.0.3.1). I'm now at a stumbling block where when I try to install a custom ROM on the device I keep getting...
"E:error in /sdcard/*ROM name*.zip
(status 0)
Installation Aborted"
Is there something I'm doing wrong or is it just the recovery programs I'm using?
What's the ROM you are trying to install?
themaker69 said:
What's the ROM you are trying to install?
Click to expand...
Click to collapse
I've tried a few now. The latest 4.4 alpha roms by Quarx, CM10 Android 4.1.2 also by Quarx and MokeeOS 43.1 and all come up with error.
Try to wipe the sdcard.
I'm downloading the file on a different computer as maybe the Antivirus on the work PC is messing it about. Also does the class of SDcard make a difference? It's only a class 4 8GB.
themaker69 said:
Try to wipe the sdcard.
Click to expand...
Click to collapse
Formatting it now.
novakanedj said:
I'm downloading the file on a different computer as maybe the Antivirus on the work PC is messing it about. Also does the class of SDcard make a difference? It's only a class 4 8GB.
Click to expand...
Click to collapse
No, the class has nothing to do. Use recovery to wipe, and not windows.
novakanedj said:
Hi,
This is the first time I've tried rooting a device so bare with me :good:.
It's taken me a few attempt to get things working on my Defy MB525 I've managed to root it with SuperOneClick and install either CWM 2.5.1.8 or SndInit2.3 (which uses CyanogenDefy Recovery v5.0.3.1). I'm now at a stumbling block where when I try to install a custom ROM on the device I keep getting...
"E:error in /sdcard/*ROM name*.zip
(status 0)
Installation Aborted"
Is there something I'm doing wrong or is it just the recovery programs I'm using?
Click to expand...
Click to collapse
4.1 should install. 4.3 and 4.4 need a newer recovery.
Sent from my Nexus 7 using Tapatalk
hotdog125 said:
4.1 should install. 4.3 and 4.4 need a newer recovery.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
novakanedj:
From 4.1 to 4.3 I installed using last TWRP. For 4.4 you need to use this.
hotdog125 said:
4.1 should install. 4.3 and 4.4 need a newer recovery.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Which recovery installs do the newer versions need and is there an install guide for these?
novakanedj said:
Which recovery installs do the newer versions need and is there an install guide for these?
Click to expand...
Click to collapse
For 4.3+ you need to first install 4.1/4.2 first to get the newer recovery.
Sent from my Nexus 7 using Tapatalk
Right I've just managed to get cm-10-20131030-NIGHTLY-mb526.zip to install from Quarx. Will let you know if the install is successful.:good: I would like to eventually install 4.4 KitKat when a more stable release is available.
edit: Succesfully installed . Just got to put Gapps on now.
Just install the zip from SDcard using your current custom recovery.
hotdog125 said:
For 4.3+ you need to first install 4.1/4.2 first to get the newer recovery.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Thanks for the reply. I noticed that after I flashed with the 4.1.2 Quarx from there was a new bootloader on it. This should make it easier. I had to wipe and start again yesterday because I cocked up the Gapps install. In the end I went with the 30th Oct 2013 build of CM10 by Quarx and got the Gapps from www.goo.im/gapps. All seems to be running fine now and finished setting it up last night.
My girlfriend has a phone she can use now as her old one broke and she didn't want to use the Defy as the data couldn't be switched off on the stock ROM and would cost her a lot on her data plan (500MB a mth). Her Mum got a new contract with a Desire C so the Defy was going spare .
Here you go folks. The miui v5 3.11.29 official for HTC ONE is released
http://en.miui.com/download-111.html
For MIUI English Forum
> http://en.miui.com/download-111.html
Harish_Kumar said:
For MIUI English Forum
> http://en.miui.com/download-111.html
Click to expand...
Click to collapse
we still need to install 4.2.2 gapps in this rom.
saketh91 said:
we still need to install 4.2.2 gapps in this rom.
Click to expand...
Click to collapse
Oh you completed installing the rom?
i guess first we need to install the kernal and then flash the rom..right?
this is the first time i am trying an official MIUI rom!
Harish_Kumar said:
Oh you completed installing the rom?
i guess first we need to install the kernal and then flash the rom..right?
this is the first time i am trying an official MIUI rom!
Click to expand...
Click to collapse
I don't know abt the kernel but I am loving this rom so far. No lags, the UI is perfect fit for the screen and loving some features like DND, IR etc..,
but the only thing missing is the gapps. We need to install separately i think. Loving the Internationalized weather widget too.
I get build prop problem, who else got it ?
hth2813 said:
I get build prop problem, who else got it ?
Click to expand...
Click to collapse
you mean while installing?. It installed perfectly for me on TWRP 2.6.3.0
saketh91 said:
you mean while installing?. It installed perfectly fine for me on TWRP 2.6.3.0
Click to expand...
Click to collapse
Yeah, what is your current rom, cid, mid ?
hth2813 said:
Yeah, what is your current rom, cid, mid ?
Click to expand...
Click to collapse
I was using SD v11.1 before and now installed this rom with no issues. Mine has supercid. I still don't understand what you meant abt build prop problem. Where did you get that error? While installing or while modifying the build prop in the rom?
saketh91 said:
I was using SD v11.1 before and now installed this rom with no issues. Mine has supercid. I still don't understand what you meant abt build prop problem. Where did you get that error? While installing or while modifying the build prop in the rom?
Click to expand...
Click to collapse
I got that problem while installing ROM, i am in GPE 4.4
I'm also getting a status 7 getprop error in recovery.
hth2813 said:
I got that problem while installing ROM, i am in GPE 4.4
Click to expand...
Click to collapse
Ok there can be different reasons for this.
1.May be a bad download. Try downloading it again.
2.May be you did not clean flash it by wiping cache,system,data. Try wiping everything except internal storage and try again.
3.May be the recovery you are using doesn't support installing this rom. Try TWRP 2.6.3.0 I got it installed perfectly with that.
4.And finally the firmware which you are on. If it is GPE firmware then try switching to sense before flashing this. I had hell lot of problems with GPE firmware like unlocking the bootloader, installing the roms etc..,
May be these are not the reasons for your problem but just give it a try and report back
Droid69 said:
I'm also getting a status 7 getprop error in recovery.
Click to expand...
Click to collapse
You get status 7 error only in three cases.
1.You edited the updater script in the rom
2.You did not download the rom properly.
3.Mainly you are not using the right recovery. Try using TWRP 2.6.3.0 or higher may be.
saketh91 said:
You get status 7 error only in three cases.
1.You edited the updater script in the rom
2.You did not download the rom properly.
3.Mainly you are not using the right recovery. Try using TWRP 2.6.3.0 or higher may be.
Click to expand...
Click to collapse
1. No
2. Could be a bad download, i will download it again and retry.
3. Im on the latest.
Droid69 said:
1. No
2. Could be a bad download, i will download it again and retry.
3. Im on the latest.
Click to expand...
Click to collapse
ok before you re download just try installing it with TWRP 2.6.3.0 too because i faced some problems earlier with the latest TWRP. Just give a try
saketh91 said:
ok before you re download just try installing it with TWRP 2.6.3.0 too because i faced some problems earlier with the latest TWRP. Just give a try
Click to expand...
Click to collapse
Rom flashed with TWRP 2.6.3.0 thanks.
Ah, i have just tried CWM Recovery and it installed successful
Droid69 said:
Rom flashed with TWRP 2.6.3.0 thanks.
Click to expand...
Click to collapse
Glad you got it installed perfectly!!
hth2813 said:
Ah, i have just tried CWM Recovery and it installed successful
Click to expand...
Click to collapse
Nice to hear that you got it installed perfectly.:laugh:
hth2813 said:
I get build prop problem, who else got it ?
Click to expand...
Click to collapse
yep the same problem
I'm currently running CM11 (02-07) with ART enabled. I'm thinking of upgrading to the current nightly, but I'm not sure if I need any special steps with ART.
I will be flashing the ROM manually because I need to modify the device number, so I'll probably be doing a reset before, which will of course reset back to Dalvik and remove all my apps.
Now my quesion is, can I backup my apps and user data while in ART with Titanium, and then restore them in Dalvik? I'm thinking of keeping Dalvik so I can flash stock remote and camera.
Thanks,
Vic
Did a Titanium backup, clean install and everything is ok. ART is good, but I'm happy to be able install the remote and camera, and maybe try xposed framework.
victorbrca said:
Did a Titanium backup, clean install and everything is ok. ART is good, but I'm happy to be able install the remote and camera, and maybe try xposed framework.
Click to expand...
Click to collapse
How did you get CM11 to flash on your wind variant g2. When I flash it fails. Its also says no MD5 file found. Please Help.
AndroidNoobeee said:
How did you get CM11 to flash on your wind variant g2. When I flash it fails. Its also says no MD5 file found. Please Help.
Click to expand...
Click to collapse
Here.
http://forum.xda-developers.com/showthread.php?t=2611749
Sent from Tapatalk.
victorbrca said:
Here.
http://forum.xda-developers.com/showthread.php?t=2611749
Sent from Tapatalk.
Click to expand...
Click to collapse
I followed the guide. But when I flash CM it fails. Do need certain kernel or something? What am I doing wrong? Also I have the wind variant if thats important.
AndroidNoobeee said:
I followed the guide. But when I flash CM it fails. Do need certain kernel or something? What am I doing wrong? Also I have the wind variant if thats important.
Click to expand...
Click to collapse
How did you flash recovery?
Sent from Tapatalk.
victorbrca said:
How did you flash recovery?
Sent from Tapatalk.
Click to expand...
Click to collapse
I flashed twrp v2.6.3.2 through flashify. I realize this isn't the most updated version of twrp for my g2 but when i flash the updated vesion (v2.6.3.4) it fails.
AndroidNoobeee said:
I flashed twrp v2.6.3.2 through flashify. I realize this isn't the most updated version of twrp for my g2 but when i flash the updated vesion (v2.6.3.4) it fails.
Click to expand...
Click to collapse
I would go to the thread and ask for help. Also paste the error you get when you try to flash CM11.
Sent from Tapatalk.
victorbrca said:
I would go to the thread and ask for help. Also paste the error you get when you try to flash CM11.
Sent from Tapatalk.
Click to expand...
Click to collapse
I noticed you are using a furnace kernel,Did you flash CM11 with stock lg kernel? If so what version of twrp did you use. I don't understand the problem because I have the dame model as you.
AndroidNoobeee said:
I noticed you are using a furnace kernel,Did you flash CM11 with stock lg kernel? If so what version of twrp did you use. I don't understand the problem because I have the dame model as you.
Click to expand...
Click to collapse
Again, post back at that other thread with the details of what you did and what error you are getting. The more detail you can give the more we can help.
In a nutshell, the recovery that you install will dictate what ROM will work on your device. For some of the ROMs in that thread you will need to install a kernel, but that depends. And I'm not sure what error you are getting.
Sent from Tapatalk.
victorbrca said:
Again, post back at that other thread with the details of what you did and what error you are getting. The more detail you can give the more we can help.
In a nutshell, the recovery that you install will dictate what ROM will work on your device. For some of the ROMs in that thread you will need to install a kernel, but that depends. And I'm not sure what error you are getting.
Sent from Tapatalk.
Click to expand...
Click to collapse
It won't allow me because the thread is only for developers.