Here's something to think about. The One's casing is indeed 100% aluminum. In every previous attempt by a manufacturer to use an all-aluminum housing the result was disastrous for wireless reception. That includes antenna-gate on the Sensation which only had a partial aluminum body. Looking at the casing HTC's either going to try to get a signal through it or the antennas will have to be forward facing to get through the glass front panel. Neither is a recipe for great and/or consistent wireless reception. It'll be interesting to see how the One does once it's tested by sites like GSMArena and Anandtech.
First of all..I still don't get the "all aluminium construction" as from some pictures the sides are clearly NOT metal but plastic.
Other than that:
His focus on the all-metal attributes is a direct shot at the iPhone 5, which similarly uses aluminum but has a top and bottom row on the back that's constructed of glass, enabling the antenna inside to broadcast and receive signals. The HTC One, however, worked around that by building the antenna into the metal back of the phone, allowing for a more seamless looking device.
While the back of the phone is part of the antenna, Croyle doesn't foresee any reception issues like the iPhone 4, which used the metal frame around the phone as its antenna, causing some signal issues when held the wrong way. Croyle promised there wouldn't be an "antennagate" with the One.
Click to expand...
Click to collapse
http://news.cnet.com/8301-1035_3-57...ke-good-first-impression-with-all-metal-body/
Its mentioned a hundred times on this forum how the antenna is integrated into this phone. The back has strips for it... look at the pictures...
Sent from my HTC One S using xda app-developers app
Eggcake said:
First of all..I still don't get the "all aluminium construction" as from some pictures the sides are clearly NOT metal but plastic.
Other than that:
http://news.cnet.com/8301-1035_3-57...ke-good-first-impression-with-all-metal-body/
Click to expand...
Click to collapse
HTC says that the white strips on the sides are in fact metal.
Eggcake said:
First of all..I still don't get the "all aluminium construction" as from some pictures the sides are clearly NOT metal but plastic.
Other than that:
http://news.cnet.com/8301-1035_3-57...ke-good-first-impression-with-all-metal-body/
Click to expand...
Click to collapse
It's no plastic @ the side its all metal....its just metal in a different colour...if u take out all components u are left full metal case so I don't see where the plastic is from
Sent from my Desire Z using xda premium
Eggcake said:
the sides are clearly NOT metal but plastic.
Click to expand...
Click to collapse
Guess again.
HTC also makes a big deal about the One's all-aluminum chassis, describing it as using a zero-gap unibody design. Indeed, available in hues of black and silver, the handset feels sturdy, has reassuring heft, and its smooth metallic skin exudes high-end craftsmanship. HTC also took pains to point out that while the thin white trim encircling the silver model I manhandled appears to be plastic, it is in fact metal.
The iPhone 5 needed a lot of glass and the iPad needs the plastic Apple logo for the WiFi and those black plastic strips for the 3g versions. The HTC fans better hope that they need less plastic than Apple or they will have an Asus Transformer prime fiasco here.
The fans better hope that HTC has thoroughly tested this thing from a basement, between two skyscrapers, to a boat, to the top of the mountain, in car, on a helicopter etc. Judging from HTC craftsmanship from the past though, especially button ergonomics, good luck HTC fans.
Oh alright, that's news for me. Very good news in fact
guess they learned what to fix after the fiasco on the one x
Tomatoes8 said:
The HTC fans better hope that they need less plastic than Apple or they will have an Asus Transformer prime fiasco here.
Click to expand...
Click to collapse
That's exactly what I thought of when it was announced the One's housing was all-aluminum. Here's what Anand said about the Prime's signal issues which Asus corrected in the Infinity by adding a plastic strip along the back where the antennas are. Wi-Fi limped along on the Prime but GPS was so FUBAR because of the all metal-back Asus ended up giving owners a detachable external dongle in order to use GPS at all.
There is no RF window on the back of the Prime where the two antennas are located. Aluminum does a fairly good job of attenuating RF signals, which contributes to worse range on WiFi than the original plastic Eee Pad Transformer. WiFi performance at the edge of reception as well as the maximum usable WiFi range are both noticeably lower than its predecessor.
expertzero1 said:
guess they learned what to fix after the fiasco on the one x
Click to expand...
Click to collapse
The One X Wi-Fi issue was caused by connectors not meeting properly during the production process. HTC can't defy the laws of physics which say metal and wireless signals aren't compatible. In the Prime scenario Tomatoes8 mentioned Asus added a second antenna and used diversity as a means of getting a signal through the metal back cover. They also amped the signal up to the point it interfered with BT which uses the same 2.4GHz frequency. The challenge is even greater using metal on a phone because there's less physical space to work with in terms of antenna size, placement, and interference with other components.
For HTC and fans of their devices sake I hope this isn't an issue. But if they succeed in using an all-metal housing and still maintain competitive wireless performance they'll be the first to do so where there’s a history of others failing.
Just another quote/info from Anandtech:
Plastic is injected into the aluminum block after certain cuts are made for the back case, which then gets machined into the final form. The One uses the top and bottom aluminum strips for antennas, both of which are actively tuned to mitigate unintended attenuation from being held. There’s a plastic insulative strip in-between the two antennas and the main body. In spite of being aluminum, the One also includes NFC, whose active area surrounds the camera region. There’s no wireless charging from Qi or WPC, however.
Click to expand...
Click to collapse
http://www.anandtech.com/show/6754/hands-on-with-the-htc-one-formerly-m7
But yeah, let's hope they really tested it...it would be a fiasco otherwise.
maybe u can use the garanty?
Eggcake said:
Just another quote/info from Anandtech.
Click to expand...
Click to collapse
Great info. But one has to wonder with an R&D budget larger than HTC's capitalization why Apple wouldn't have figured the same thing out and avoided the issues they faced when they took the Apple logo off the back of the iPad and moved the antenna under the perforated speaker grate and had to use a plastic trim strip over the antenna on the 3G/GPS version. The only real pass/fail test will be when there are One's in people's hands for a couple of months. It took almost three months (launched in March, issue identified in June) for users to figure out the commonality in the One X's wireless issue. Kudos to HTC if they've figured out how to design a metal device with decent wireless performance where others haven't been able to.
Related
I am currently working on a case for the atrix that is milled out of a solid block of aluminum using a cnc machine that a will be air tight around the phone except where the speaker is on the phone there will be and a so called PORT for the sound to be forced throught that will be directed to the front of the phone using a port that will be front facing so you dont have to cup your hand around your phone to hear things, it also will have a kickstand if you all have any other ideas to incorporate into this aluminum case please feel free to post
Have you tried this with aluminum foil? You might save yourself some wasted effort.
I'm thinking such a case could have deleterious effects on some or all of the various bands of the RF spectrum. There are 3 RF based features on these phones. GPS is likely to be the most affected based on signal strength. Reduced range for both WiFi and cell is likely.
I may be wrong and hope I am. I am speculating as I have no idea where the various antennae on these phones are located.
OOPS, I forgot about Bluetooth.
Well... i think it all depends on the case, really. I mean... look at the iPhone 4. Has that whole Antennagate issue... yet companies like ElementCase release the Vapor 4... an aluminum band that get's affixed around the phone, covering the coveted antenna band.
Kickstand yeee..
Looks like an amazing case the kickstand is huge +. If the sound changes even a little bit will be a disadvantage. Engraved styles is what you can add, some parts you can make glossy other brushed. As for assembly I'd like it to be two parts with screws like the vapor bumper, but for most people will be a drawback.Shouldn't be thick since the atrix is pretty thick already. And also have you tought of doing a battery door replacement to incorporate those things. If you are making them for sale I'd like to know because it sounds like an awesome case.
nikidorian said:
Looks like an amazing case the kickstand is huge +. If the sound changes even a little bit will be a disadvantage. Engraved styles is what you can add, some parts you can make glossy other brushed. As for assembly I'd like it to be two parts with screws like the vapor bumper, but for most people will be a drawback.Shouldn't be thick since the atrix is pretty thick already. And also have you tought of doing a battery door replacement to incorporate those things. If you are making them for sale I'd like to know because it sounds like an awesome case.
Click to expand...
Click to collapse
Atrix could stand to be thicker. Not too fond of the thinnest phone eva craze.
Iphone > galaxy s 2.
Lie the phone on an aluminum desk and watch your service fade away. I have an aluminum desk at work for drafting and I gi from 3 bars to no service at all if I set it on my desk. Pick it up about 6 inches and bame, 3 bars again. Im right in front of a window too. I have to put my phone up on my filing stand. Once phones went with internal antennas, metal casings had to go. Im pretty sure it will kill the signal at 3 bars and lower. Mill it out of abs and it will be a hot item. For those wanting a thicker phone, do a search for extended batteries. They come with a modified back case that's thicker to accommodate the fat battery. Almost an 1/8th to 1/4 inch thicker.
Sent from my MB860 using xda premium
Dirtburgler said:
Lie the phone on an aluminum desk and watch your service fade away. I have an aluminum desk at work for drafting and I gi from 3 bars to no service at all if I set it on my desk. Pick it up about 6 inches and bame, 3 bars again. Im right in front of a window too. I have to put my phone up on my filing stand. Once phones went with internal antennas, metal casings had to go. Im pretty sure it will kill the signal at 3 bars and lower. Mill it out of abs and it will be a hot item. For those wanting a thicker phone, do a search for extended batteries. They come with a modified back case that's thicker to accommodate the fat battery. Almost an 1/8th to 1/4 inch thicker.
Sent from my MB860 using xda premium
Click to expand...
Click to collapse
Those fat batterys are horribly ugly. No one wants a fat block sticking out the phone. We want a little thicker door to make the phone feel more solid and look the same.
Someone on the inspire forum used conductive tape on top of their antennas to boost signal dramatically! Anyone know the insides of a500 know if doing this would help us cuz wifi sucks..?
Sent from my Inspire 4G using Tapatalk
Funny, I am going to be making some conductive glue in the next day or so. I was wondering what I should do with the leftover. I will consider putting some on the antenna just for kicks. maybe I can coat some paper and extend it a bit. If anyone has a good idea of how to implement it I might give it a shot. I'm certainly not a radio engineer type person, so I really don't know if there are any guidelines that I should follow. Like whether or not this will need direct contact with the core wire, recommended length/shape to match frequency, what matters, what doesn't, would a graphite conductor even work, etc. Keep in mind that the resistance will increase with length on this adhesive. I can double coat it and help some but there is no way to avoid this without embedding a wire. I already get a good signal but there's always room for improvement. And I need to open my case to fix a dented corner. Lucky I didn't break the glass when I dropped it on the pavement...
And if anyone believes that this is a bad/goofy idea please say so. I'd rather know not to try something and why than to waste the time.
I was thinking that you could use small strips of aluminum tape (the kind that is used to seal furnace duct joints)
It is very sticky and you would have to use some Goo Gone on a Q-Tip to remove the adhesive from a small strip where the antenna contacts the tape.
I am going to try this once my plastic opening tool kit arrives from China.
dincdoes.me said:
Someone on the inspire forum used conductive tape on top of their antennas to boost signal dramatically! Anyone know the insides of a500 know if doing this would help us cuz wifi sucks..?
Sent from my Inspire 4G using Tapatalk
Click to expand...
Click to collapse
I thought you sold your 500?
Considering the 500 uses the same hardware manufacturer for the antenna, I can say I get good Wifi in my flat. Even in the toilet.
GPS though, I need to be within 3 meters of a window, but that's understandable.
Moscow Desire said:
I thought you sold your 500?
Considering the 500 uses the same hardware manufacturer for the antenna, I can say I get good Wifi in my flat. Even in the toilet.
GPS though, I need to be within 3 meters of a window, but that's understandable.
Click to expand...
Click to collapse
I was gonna sell it but a family member held onto it for $200 till I paid em back so I did n having fun again
But.. who ever wants to extend their radio reach with out buying new parts i will be trying conductive tape. My inspire can get WiFi anywhere in my house my a500 looses a bar 10 feet away from my Netgear CG3000D ..
Something needs to work.. I'm tired of laying in bed like a contortionist
Sent from my Inspire 4G using Tapatalk
Everyone seems to be so happy that it's an aluminium unibody. Is this the same aluminium as on the back of the Sensation XL ? If so i'm worried that it will be quite slippery. I remember using a case on mine even when at home because it was too slippery while naked (hehehe).
Yes, it will be just like any other phone with an aluminium back.
Eww
Maybe the black version will grip a little better due to the paint.
maniacaus said:
Eww
Maybe the black version will grip a little better due to the paint.
Click to expand...
Click to collapse
It should/could be anodized, not painted...
I recommend covering the back with a silicon case as aluminium dents very easily. It will half the value of your phone if you plan on selling it in the future.
If watch one of those how they make it videos you will see they coat the silver one as well so hopefully the coating will have some grip
Sent from my One X using Tapatalk 2
The bigger concern should be it scraping, denting, and deforming if its dropped and lands on a corner. From wiki...
"Aluminum is a relatively soft, durable, lightweight, ductile and malleable metal with appearance ranging from silvery to dull gray, depending on the surface roughness. It is nonmagnetic and does not easily ignite. A fresh film of aluminum serves as a good reflector (approximately 92%) of visible light and an excellent reflector (as much as 98%) of medium and far infrared radiation. The yield strength of pure aluminum is 7–11 MPa, while aluminum alloys have yield strengths ranging from 200 MPa to 600 MPa.[7] Aluminum has about one-third the density and stiffness of steel. It is easily machined, cast, drawn and extruded."
Here's an iP5 and Prime after some use...
The polycarbonate body on the OG One X had issues with abrasion creating "shiny spots." A lot of us that didn't want to always use a case used these protectors. Their wet-apply and dry so tight that you can feel the texture of the "Beats logo" through them. They make the device glossy but better glossy than permanently scratched. It would be great for the One because it's such a great looking device when naked.
http://www.bestskinsever.com/
BarryH_GEG said:
The bigger concern should be it scraping, denting, and deforming if its dropped and lands on a corner. From wiki...
"Aluminum is a relatively soft, durable, lightweight, ductile and malleable metal with appearance ranging from silvery to dull gray, depending on the surface roughness. It is nonmagnetic and does not easily ignite. A fresh film of aluminum serves as a good reflector (approximately 92%) of visible light and an excellent reflector (as much as 98%) of medium and far infrared radiation. The yield strength of pure aluminum is 7–11 MPa, while aluminum alloys have yield strengths ranging from 200 MPa to 600 MPa.[7] Aluminum has about one-third the density and stiffness of steel. It is easily machined, cast, drawn and extruded."
Click to expand...
Click to collapse
Hah~ People usually never leant unless they accidentaly their phones for the very first time..
Some good news was HTC's execs and PR mentioned more than once that they had opt for a type custom of aluminium-magnesium unibody that is harder than iphone 5. I'm aware of iPhone 5's body wasn't doing well, but at least HTC dare to claimed they used a harder one..
It's all soft touch. Think mac book feel.
Sent from my One X using xda premium
I may be an outlier here...but I would prefer a good feeling phone that gets scratched on the back over a slippery unscratchable phone.
Seen it life on monday...the aluminium feels really nice! You got enough grip and nothing feels slippery. But the best is: it seems that htc has learned from apple...the antennas are doing their job very well. I kept my hands close around the whole case and there were no connection issues. Provider was O2 germany, which is not the best we got here .I hope I'll get mine tomorrow .
HTC's aluminum casing is going to be pretty solid. The iPhone 5's aluminum case is WAY too thin and the anodizing layer is incredibly thin in order to not compromise the structural integrity. I'm guessing Apple did that in order to keep weight down and from inexperience in metal unibodies. HTC is definitely not going to have their phones scuff remotely as easily, as the grade of aluminum will be stiffer and the anodization will be much thicker.
ike2903 said:
Seen it life on monday...the aluminium feels really nice! You got enough grip and nothing feels slippery. But the best is: it seems that htc has learned from apple...the antennas are doing their job very well. I kept my hands close around the whole case and there were no connection issues. Provider was O2 germany, which is not the best we got here .I hope I'll get mine tomorrow .
Click to expand...
Click to collapse
I pre-ordered one and good to know that it has no problem in signal like iPhone, But sometime signal bar doesn't reflect minor change in signal degradation so can you please download the free apps called 'Network Signal info' from market and check signal graph activity in the low signal area with holding your phone all the different way so we can clearly see if it has any degradation or loss in wifi or GSM signal
https://play.google.com/store/apps/details?id=de.android.telnet&hl=en
Thanks
---------- Post added at 05:36 PM ---------- Previous post was at 05:27 PM ----------
For me the best place to check the Mobile Signal is my workplace's canteen which is in the approx 10-12 steps downstair where I got only one signal bar and sometime no bar showing on my S3 but still I can talk and listen without disconnection or call loss, So any phone I got 1st I check signal quality and if it failed to hold the signal at this place I can surely assume that the problem with Signal quality of phone and I simply return that phone back, same thing happened with 2 Nokia Lumia 820 and I return it back, Signal metre apps is really useful to test signal quality with any phone even without connecting call
My mytouch 4g is plastic back with aluminum battery door the device is slippery as hell on my had.. 2 plus years later and I've only dropped it once from my hand. Why is it being slippery and issue? Really? Have the complaints gone that low. Hold your device better. I grab my phone and its solid on my hand. It's not going anywhere.
By the way, this is being that the mt4g is tiny too. The one is going to be much easier to hold.
maniacaus said:
Everyone seems to be so happy that it's an aluminium unibody. Is this the same aluminium as on the back of the Sensation XL ? If so i'm worried that it will be quite slippery. I remember using a case on mine even when at home because it was too slippery while naked (hehehe).
Click to expand...
Click to collapse
Seriously？ Is it that hard to hold a 4.7 inch phone
I Just had this idea, what if somebody would produce backplates for the nexus 7 in aluminium? Like replace the whole backplate, to get an iPad premium feel to it?
Would it be possible due to the antennas? I'm curious because I just broke my Nexus 7 backplate, and it would be nice to have something more premium than plastic on the back.
I own a Nexus 7 with LTE
No, because Google is cheap
You get what you pay for
Potetsjokolade said:
I Just had this idea, what if somebody would produce backplates for the nexus 7 in aluminium? Like replace the whole backplate, to get an iPad premium feel to it?
Would it be possible due to the antennas? I'm curious because I just broke my Nexus 7 backplate, and it would be nice to have something more premium than plastic on the back.
I own a Nexus 7 with LTE
Click to expand...
Click to collapse
Wireless charging will not work with an aluminum back plate. Also reception is exponentially degraded.
fosser2 said:
Wireless charging will not work with an aluminum back plate. Also reception is exponentially degraded.
Click to expand...
Click to collapse
Well. Depends on where the antennae are. My HTC one is a nice block of aluminum.
Sent from my HTC6500LVW using Tapatalk 4
dottat said:
Well. Depends on where the antennae are. My HTC one is a nice block of aluminum.
Sent from my HTC6500LVW using Tapatalk 4
Click to expand...
Click to collapse
Your HTC One , has external antennas, the aluminium case is used as the antenna's just like the iPhone 4+ , this is why you have this white plastic strips , to separate the the casing in to different antenna's .
When it comes to antennas and aluminium body's doesn't matter where the antennas located ,aluminium blocks any kind of wireless signal ,so you have to use some kind of RF window , like on the Wifi iPad's , the apple logo is a "RF window" for the wifi antenna, or the plastic strip on top of the Cellular iPad's .
1. Learn how to electroplate plastic (it ain't easy) http://www.azom.com/article.aspx?ArticleID=525 and take off the back and electroplate it.
2. Get a lathe and cut out your own from a block of aluminum.
3. Take off the back, make a mold, and pour molten aluminum into the mold. Polish to heart's content and install.
None of the options are really easy unless you're an experienced fabricator.
Best to choose the tablet that has what you want before you buy, so you don't regret not having a block of aluminum later.
Myself, I don't automatically think that METAL = BETTER QUALITY. I look at the ACTUAL quality of the device.
iamezio said:
Your HTC One , has external antennas, the aluminium case is used as the antenna's just like the iPhone 4+ , this is why you have this white plastic strips , to separate the the casing in to different antenna's .
When it comes to antennas and aluminium body's doesn't matter where the antennas located ,aluminium blocks any kind of wireless signal ,so you have to use some kind of RF window , like on the Wifi iPad's , the apple logo is a "RF window" for the wifi antenna, or the plastic strip on top of the Cellular iPad's .
Click to expand...
Click to collapse
That was my point. He's only talking about the backplate.
Sent from my Nexus 7 using Tapatalk 4
lotherius said:
Myself, I don't automatically think that METAL = BETTER QUALITY. I look at the ACTUAL quality of the device.
Click to expand...
Click to collapse
I have an HTC One and I like the premium feel but I much rather would like to have a phone made by plastic (but I like sense so that's why I bought it) , besides the antenna problem of metal:
Plastic is more durable, scuffs less easy
Plastic is lighter and slightly elastic , therefore less impact when falling a smaller chance to break the display and just more comfortable to hold or deformity of the body
Alluminium phones remind me of bug(arthropod) "design" instead of the much more flexible and elegant "design" of vertebrates
Has any one found a bumper case for the yotphone 2 yet
some retailers including yota are providing them free with handset
yota customer services wont stipulate where from but just keep watching for any news. internet search doesnt show any one yet providing them . would be usefull!!!!
I got mine as part of a promotion for orders during most of January. As you say, some retailers are selling them along with the handset. Have you tried asking the facebook page? They seem pretty good with answering questions.
sorry but no face book or any other social network member, guess i will have to wait for yota or someone to enlighten me
Fair enough. Sorry then dude, hope they start being sold separately eventually for you.
Just thought would mention that the bumper is for sale on the yota website now. It may have been a while but just a heads up for those still looking for one.
yotaphone 2 bumper case
finally now available on line via the buy now / store @ about £12
kam1962 said:
finally now available on line via the buy now / store @ about £12
Click to expand...
Click to collapse
I can remember in a video yota showed different colours of bumper case but on their site shows only black.
Has anyone bought the aluminium bumper case?
adamo86 said:
Has anyone bought the aluminium bumper case?
Click to expand...
Click to collapse
I Bought an aluminium one on eBay. Short review and some pics:
- fit is OK, no slack
- finish looks OK, mine is matte black
- protrudes a bit to the front and the back (so the device does not lie on the glass when put down on a perfectly flat surface)
- edges are quite sharp, might leave marks on the case in due time. bumper has some soft tape on the inside, but that doesn't cover the sharp edges. The hole in the bottom for USB and microphone has these sharp edges too, not comfortable as I usually support the phone with my pinky there.
- adds about 2mm in width and 3mm in length to the phone. (7.2 x 14.8 cm with bumper, 7 x 14.5 cm without). Not too bad, but you can feel the difference initially.
- buttons can be operated OK, although power button does not stick out that much.
- small clasp in the corner
All in all not bad for a couple of dollars. I don't own the bumper as sold by Yota Devices, so I can't compare it.
Hopefully it will absorb some impact when falling on the floor too, but I will leave that part to someone else to review.
edit 1: some additions after 2 weeks of use:
- There seems to be some impact on reception. In an area with low signal strength, the bumper seems to cause the connection to become unstable/drop. Removing the bumper restores the connection. In good reception areas it's harder to note the impact.
- The sharp edges at the bottom are annoying me, I'll have to smooth them out, or lose the bumper.
- No scratches (yet) on the phone though from the bumper
edit 2: Don't know how I missed this earlier, but GPS reception is heavily impacted by this bumper
I went for a run yesterday, and my Endomondo app could not get a good lock. The map only showed approximate location, but it wouldn't start recording my run based on that. After 15 minutes still no lock, until I thought of the bumper. Removed it, and got a solid lock after 3 seconds...
Will the phone get scratches after use. Or r the ruff edges away from The device
adamo86 said:
Will the phone get scratches after use. Or r the ruff edges away from The device
Click to expand...
Click to collapse
I've only received it today, so can't comment on long-term use, but the sharp edges are on the inside as well. The little review above is mainly positive in the price/value department, the Yota Devices bumper might be higher quality.
Someone care to review the Yota bumper here?
Rrreutel said:
I've only received it today, so can't comment on long-term use, but the sharp edges are on the inside as well. The little review above is mainly positive in the price/value department, the Yota Devices bumper might be higher quality.
Someone care to review the Yota bumper here?
Click to expand...
Click to collapse
I have a bumper case which came with the device but I don't know if it's from yotaphone. The bumper feels like silicone to me may be it's gel. I prefer gel cases. It feels flimsy.
I have the rubber bumper from yota itself, nice thing.
happy with it for 15usd
Yota Bumper
My "official" Yota Phone bumper arrived, here's a short review:
Material:
Not sure what the material is called, but it's like a matte rubber, but less flexible than rubber, thougher. It's somewhat grippy, but not too much. Doesn't feel like gel or silicone to me.
Dimensions:
It adds 2 mm in width, and 3 mm in length to the phone (just like the aluminium one). It fits nicely, altough the sides are slightly 'floppy', you can stretch it away from the phone easily. I can imagine that only getting slighty worse, not better over time.
features:
The bumper does not have 'real' plastic or metal buttons, buttons are just molded into the rubber. The back side has a thicker rim than the front.
Comparison with the aluminium one:
I have to say the cheap aluminium case looks slightly more classy to me, a bit more svelte, with nice paint & real buttons. It does have a small buckle, which some may find distracting.
The rubbery Yota one looks a bit more ordinary, less luxurious, to my taste. However the aluminium one does have practical drawbacks: sharp edges (especially annoying on the bottom opening), impact on reception (both mobile and particularly GPS, see below), and it might scratch the device at some time, although I haven't seen that in a few weeks of use.
The metal one takes a bit more care to put on, to prevent scratches, the rubber Yota one slips on in a second.
BTW: I updated the aluminium bumper review to mention poor GPS reception
I want this bumper
Sent from my YD201 using Tapatalk
adamo86 said:
View attachment 3375394
Click to expand...
Click to collapse
adamo86 said:
View attachment 3375394
I want this bumper
Sent from my YD201 using Tapatalk
Click to expand...
Click to collapse
Agreed, This looks like the bumper you can get from the Russian yotaphone store... they even do it in different colours
http://yotaphone.com/ru-en/store/#bumper
Does anyone know how to obtain the official yota bumper if one does not live in the UK or Russia (I am in Canada)? I have contacted the UK yota store but they will not ship outside of the UK. I cannot find it anywhere else with the usual online dealers (clove, expansys, ...). Thanks.
Cool cases check it out guys
http://www.aliexpress.com/store/group/For-yotaphone-2/429058_501181446.html
Sent from my YD201 using Tapatalk
scdoyle said:
Does anyone know how to obtain the official yota bumper if one does not live in the UK or Russia (I am in Canada)? I have contacted the UK yota store but they will not ship outside of the UK. I cannot find it anywhere else with the usual online dealers (clove, expansys, ...). Thanks.
Click to expand...
Click to collapse
It's sold in other countries too (I purchased mine from the French Yotaphone website), but this will be of limited benefit to you until they add Canada/USA to the list... (on a side note, anyone knows when the North America Indigogo campaign ends, and when the phone will be officially launched there?)
If you want, I have a trip planned to Canada in late August, I can certainly purchase one and either hand it to you if you live close to Montreal, or post it from there using local post services if you're too far away (Canada is definitely a biiig country).
Let me know if you're interested.