[Q]Is this a LCD or a digitizer problem? - Defy Q&A, Help & Troubleshooting

I hate making new threads... but I've been looking at different places and haven't found the right answers to my questions... so yeah.
I have a GREEN LENS Defy MB525. It has gone through some trouble. It has some blue marks and such on the screen.
I found this and will be trying the method soon to see if the screen gets fixed. But, the owner of the phone had disassembled it to change the ear piece that was broken. Afterwards, the phone's screen doesn't take all the touches.
On the QWERTY screen, when you try to use the "Shift key or any of the letters (zxc...) on the phone, it takes the keys on top of them or below them.
I want to try to fix the phone but I don't know if it's a problem with the LCD that needs to be replaced, the digitizer or simply something else entirely.
The phone is running CM 10 2ndboot 2012-12-31 but it does the same on stock. I already tested it.
Any tips or help will be appreciated to finally have a working Defy
I also found this but since I don't have another screen to use for testing... well yeah...

I had such problems before after changing the speakerphone . All I did was to get a new digitizer and clean the inner screen using lighter fluid
Sent from a Motorola Defy

Okay, so it appears to be a digitizer problem?? Alright.

xXLostsoul111Xx said:
Okay, so it appears to be a digitizer problem?? Alright.
Click to expand...
Click to collapse
When in doubt , change both
Sent from a Motorola Defy

xXLostsoul111Xx said:
Okay, so it appears to be a digitizer problem?? Alright.
Click to expand...
Click to collapse
Because you put the phone in the freezer you maybe destroy the digitizer but also be aware to check ALL the contacts and terminals from the motherboard for oxidization.

I was asking because I don't wanna invest into something that isn't really needed. Don't have a steady income. >.>

xXLostsoul111Xx said:
I was asking because I don't wanna invest into something that isn't really needed. Don't have a steady income. >.>
Click to expand...
Click to collapse
I didn't put my Defy in the freezer though
Sent from a Motorola Defy

I haven't put it in the freezer yet.
I am thinking of doing it since it seemed to produce results in that thread.
I specifically said "will be trying the method soon".
Since it's such a strange advice I have yet to do it. I wanted to asked about my other problems before trying that.
The circles on the screen I am aiming to fix with the freezer thing have nothing to do with my problem since I've had those circles from way before the problem appeared.
It appeared when the phone was disassembled to change the earpiece. Please don't jump to conclusions so quickly. I am only considering that method to fix the circles in the screen since Auris posted in that thread favoring it.
Auris 1.6 vvt-i said:
Wrap it up in a plastic bag. Wrap it reeeeeeeally good, then duct tape it. After taking it out of the freezer, let it stay with the bag for at least 6 to 8 hours, 'cause when you take a cold object into a warm room, it condenses. Make sure your phone is well acclimated and there is no condense whatsoever. Then you can unwrap it and put the battery back in.
Click to expand...
Click to collapse
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
All that aside... since the freezer thing is not really relevant to the state of the phone as of writing this message...
Is there a way to know if the digitizer is busted? or the LCD? It was fine until my friend opened the phone to change the earpiece then the phone started showing the weird symptom where it wouldn't let him type any letter on the third line of the keyboard (zxc...). I tried the Android keyboard (AOSP) and swiftkey 3. The problem still persist even if I go to stock rom.

Let make a little light: The color problem relied to LCD and the keyboard malfunctioning is from digitizer. Because is improbable to broke both from one shot disassemble again, reattach CAREFULLY the digitizer and LCD and power on. Good luck.

Related

Digitizer Non Responsive

Hey guys.
Owned the phone for a few months now and have started to notice a really odd problem. For a while the screen was being fairly unresponsive to touches and I couldn't figure out why. Taking the screen protector off fixed it temporarily but now the issue is back.
I finally realised that the issue was a black smudge that would appear whenever I pushed too hard on the screen. I'm assuming this registers as a touch on the screen and prevents it from working. Rubbing the stylus over the area usually makes it dissipate and the screen becomes responsive again, but it would come back not long later after general use.
Also there's some fairly odd rainbowing underneath the digitizer that moves around when you press on the screen. It circles around the smudges when they appear.
I know that all sounds fairly vague, but any help on the issue would be great. Is a new digitizer in order or could it be fixed by just dissassembling it? I've tried using a suction cap to make the problem go away, the rainbowing disappears but slowly comes back again. Also I haven't dropped the phone, left it near anything etc, besides the digitizer problem the phone works fine.
Thanks in advance!
(On a side note, I bought the phone off eBay and had to use a serial number locater to determine the region of the phone. Found out it was destined for India when I'm in Australia. Fairly odd, but what are the warranty implications? Is it still covered?)
Same problem here!
I've sent it to HTC for repair, since my Diamond2 has 1 year warranty and I only bought it in May/09. HTC said that screen issues are excluded of the warranty and that I have to pay about €70 for the screen repair, because, they say, the problem is due to misuse - wich I don't think is true.
Daisjun said:
Hey guys.
Owned the phone for a few months now and have started to notice a really odd problem. For a while the screen was being fairly unresponsive to touches and I couldn't figure out why. Taking the screen protector off fixed it temporarily but now the issue is back.
I finally realised that the issue was a black smudge that would appear whenever I pushed too hard on the screen. I'm assuming this registers as a touch on the screen and prevents it from working. Rubbing the stylus over the area usually makes it dissipate and the screen becomes responsive again, but it would come back not long later after general use.
Also there's some fairly odd rainbowing underneath the digitizer that moves around when you press on the screen. It circles around the smudges when they appear.
I know that all sounds fairly vague, but any help on the issue would be great. Is a new digitizer in order or could it be fixed by just dissassembling it? I've tried using a suction cap to make the problem go away, the rainbowing disappears but slowly comes back again. Also I haven't dropped the phone, left it near anything etc, besides the digitizer problem the phone works fine.
Thanks in advance!
(On a side note, I bought the phone off eBay and had to use a serial number locater to determine the region of the phone. Found out it was destined for India when I'm in Australia. Fairly odd, but what are the warranty implications? Is it still covered?)
Click to expand...
Click to collapse
You have collapsed your layers between lcd and digitizer.
Some folks here use duct tape to repeatedly pull the layers apart and it fixes their issue for a while.
Thought it'd be something along those lines. I'll give the duct tape trick a try, can you point me to some other threads? I tried searching but was probably using the wrong terms.
Also vasco that's complete bollocks. I've kept my phone in its case the whole time I've had it, never put any pressure on it or had it in a rough environment. I'd throw a few customer complaints their way, especially if other people have had the same issue. Nice to know I'm not alone at least.
Daisjun said:
Thought it'd be something along those lines. I'll give the duct tape trick a try, can you point me to some other threads? I tried searching but was probably using the wrong terms.
Also vasco that's complete bollocks. I've kept my phone in its case the whole time I've had it, never put any pressure on it or had it in a rough environment. I'd throw a few customer complaints their way, especially if other people have had the same issue. Nice to know I'm not alone at least.
Click to expand...
Click to collapse
search for "newton rings"
Daisjun said:
Thought it'd be something along those lines. I'll give the duct tape trick a try, can you point me to some other threads? I tried searching but was probably using the wrong terms.
Also vasco that's complete bollocks. I've kept my phone in its case the whole time I've had it, never put any pressure on it or had it in a rough environment. I'd throw a few customer complaints their way, especially if other people have had the same issue. Nice to know I'm not alone at least.
Click to expand...
Click to collapse
The issue is being discussed here:
http://forum.xda-developers...522813
I've already filed a complaint to the comm's regulation office. I'me presently waiting for their response.
had the same issue.. I just replaced the digitizer, it's a bit tricky but certainly possible.. yours is not that old so it should be repaired under warranty if you can have that done (have no clue about your situation there..)
digitizers are cheap on ebay
disassembly:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Daisjun said:
Thought it'd be something along those lines. I'll give the duct tape trick a try, can you point me to some other threads? I tried searching but was probably using the wrong terms.
Also vasco that's complete bollocks. I've kept my phone in its case the whole time I've had it, never put any pressure on it or had it in a rough environment. I'd throw a few customer complaints their way, especially if other people have had the same issue. Nice to know I'm not alone at least.
Click to expand...
Click to collapse
Here is my thread about this.
I am in the same boat as you - phone was destined for somewhere in Asia, and I am in Australia. I contacted HTC, and they also told me that the problem could be caused by misuse, even though I KNOW it wasn't, as my phone is always in it's case unless being used, never dropped etc. It sucks, but I think I will just replace the digitizer myself.

[Q] Screen replacement, leftover piece

Hey! I just replaced a broken screen and it went quite well, aside from the fact that my mic is not really working as it should anymore (it sounds like I am really far away whenever I speak). After the reassembly, I noticed one plastic piece which for the life of me I cannot find a suitable place for. Does anyone know where it is supposed to go?
I've never had that piece loose after replacing my screen (I've gone through 4!!).
The microphone problem seems to be a common problem with screen replacements (judging by xda, other forums and product reviews). I don't know a fix for that, but wanted to let you know it seems to be everyone
Sent from my MB526 using xda premium
Haha ok, no I haven't been able to spot it n any how-to video or anything so I am completely stumped. Does anyone know if the mic problem is fixable? Been googling a bit without result.
Edit: " end of my woes.
I had the same thing as adam in the end. its the little orange silicon bit that shields the microphone. it fits into the fornt cover near the microphone hole. I accidentally threw it away with the old cover and then had the problem. I had to buy a complete new casing in the edn but it is working fine now.
Chris"
Found this in another thread, but... Hmmm, I know of the three orange parts and I have taken good care of them. None of those are clowe to the mic though, or perhaps I am mixing up the mic with somethng else? Oh well, there was somethng else about a rubber part behind the display, perhaps I'll just stick my rubber thingie in there. Yup.
rakitin said:
Edit: " end of my woes.
I had the same thing as Adam in the end. its the little orange silicon bit that shields the microphone. it fits into the front cover near the microphone hole. I accidentally threw it away with the old cover and then had the problem. I had to buy a complete new casing in the end but it is working fine now.
Chris"
Found this in another thread, but... Hmmm, I know of the three orange parts and I have taken good care of them. None of those are close to the mic though, or perhaps I am mixing up the mic with something else? Oh well, there was something else about a rubber part behind the display, perhaps I'll just stick my rubber thingie in there. Yup.
Click to expand...
Click to collapse
I think I know what Chris was referring to, it's a rectangular red/orange silicone.... thing. I'll edit this with link to a video at the time it appears, when I get to a computer that is.
-Sent from my MB525 on Quarx's 2nd boot CM10 [BL7]
pk92 said:
I think I know what Chris was referring to, it's a rectangular red/orange silicone.... thing. I'll edit this with link to a video at the time it appears, when I get to a computer that is.
-Sent from my MB525 on Quarx's 2nd boot CM10 [BL7]
Click to expand...
Click to collapse
Thank you! I will open it up again tonight and see if I can fix it. Apparently I also managed to cause some problem with the headset since the right earpiece no longer works. Only the left one... Seems like i really shouldnt do these kinds of repair work myself.
Edit: i think I used too much glue a the bottom while fastening the screen and that is why the mic is not working as it should. Just putting it here so others might take t ny consideration if they see this post. Guess the only way to fixit is to buy a new front.

[Q] touch issues

I have a NST with glowlight and i have touch issues quite often... when using the keyboard when i touch backspace it touches "h".. when i touch space .. it touches b ... does anyone have these screen issues? it's like phantom touches.. i takes me 5mins to type something
This is a known issue. I just received mine in the mail and it had issues. I found you can clean it and it may help. But for me, since it is brand new, I just had them ship out a new one. If you are not under warranty, I actually just did a factory restore and it stemmed to have helped a bit.
lekofraggle said:
This is a known issue. I just received mine in the mail and it had issues. I found you can clean it and it may help. But for me, since it is brand new, I just had them ship out a new one. If you are not under warranty, I actually just did a factory restore and it stemmed to have helped a bit.
Click to expand...
Click to collapse
ok thx. It's brand new for me also... not even 1 month... do i need to ship back my nook to get a replacement? i bought from ebay... i need to contact who to report the issue? I read when they give u a replacement, they you a refurbished one?
edit: hmmm so this issue is faulty hardware? or it's just cleaniness? and it will happen sooner or later on any nook? will a cover help?
yeahman45 said:
ok thx. It's brand new for me also... not even 1 month... do i need to ship back my nook to get a replacement? i bought from ebay... i need to contact who to report the issue? I read when they give u a replacement, they you a refurbished one?
edit: hmmm so this issue is faulty hardware? or it's just cleaniness? and it will happen sooner or later on any nook? will a cover help?
Click to expand...
Click to collapse
Nook touch screens use infra-red sensors/emitters located around the edges of the screen. If the transparent plastic sandwiched between the screen and the bezel gets dusty, it can cause problems.
cowbutt said:
Nook touch screens use infra-red sensors/emitters located around the edges of the screen. If the transparent plastic sandwiched between the screen and the bezel gets dusty, it can cause problems.
Click to expand...
Click to collapse
so it's not really a hardware fault but it's because of dirt?? any cover case that can protect against such scenarios? how do i clean it?
I think there are two scenarios (perhaps more). Faulty hardware in which the infra red sensors do not function correctly or dirt/ dust impeding their ability to function. One always hopes for the latter.
The reset I did only helped for about an hour.
First try to clean it.
Since you got it off eBay, start by contacting the seller. Ask the person if it is still under warranty.
Then, contact 1800thebook to get a replacement. If it is not under warranty, I am not sure what your options are. EBay and electronics is always a gamble. Sorry.
~Leko
Go forth and work toward your salvation with diligence.
ok thx,... i have tried cleaning it up but it helps for a few seconds but then it gets freaky at times.. it's a pain to type! do you guys ever take notes with it??? it's impossible...
i don't think it's a hardware issue since the first 2 weeks it works with no problems... i was keeping it in the box while not in use... since i started not keeping it in its box.. i am getting these touch issues... so seems related to dust...
will i need to send back my nook to get a replacement... sounds pretty annoying to do so.. shipping is damn expensive
sidenote: looking at the edge of the nook, i see shiny particles... is this normal or is this dust?
i can't even type my wifi password anymore... every button i touch also "ghost" touch the corresponding middle button.. e.g. when i press d, i get dg ... how do i clean that damn thing? where do i need to clean exactly?? i am cleaning the edge.. does not seem to work.. sometimes it seems ok, then 2 secs later it gets messed up again
Cleaning the screen is a different reason to normal screens. Normally you just want the greasy finger prints off etc. However thats for a resistive or capacitve based touchscreen. NST/NSTG touchscreen works on an infrared array running along the edges ABOVE the screen rather than a stuck on touchscreen so as not to affect the contrast in sunlight.
This means a piece of particulate matter on the screen will affect the touch sensor.
If its confused sometimes it won't work at all! The worst environment to ever take your NST is to a sandy beach, really don't do it.
Personally I use a air duster (compressed air can) to get those pesky bits out of the edges.
When not using NST keep face down to keep out bits of crap or keep in a case..

Nothing is impossible - opening the HTC One. Now with video!

After a trip to a shower my HTC One was declared dead (boot loop even after rice, humidity remover, heat, and others) I figured I would open the phone even it it meant that I could destroy it. It turns out that all you really need is patience and tools already available. Sure, I did bent the upper cover but, hey, everything else is intact.
I started by removing the volume button and started using those "guitar picks" around going down. Added some heat to unset the glue and moving slowly I started prying open the right side (when you are looking at the lcd). Than continued moving down until the left side was stuck. After that I went high on the volume button to set the whole right side open.
Now I'm using the other tool (the one that looks like a lever?) I started opening the left side. This side was a lot harder so I applied heat again. After that the glue wasn't an issue and it started to open nicely. Now I have the phone open and I'll see if I can get it working again.
Sorry for the English. I'm too excited to correct the mistakes and I'm not from an English speaking country.
Edit: added tools pictures.
The guitar picks were used to start opening the phone. The green and blue tool were used to open the left/top/bottom sides. The light blue tool was used mostly as a lever on the right side that was already open.
Edit2:
Video will be here shortly: http://forum.xda-developers.com/showpost.php?p=48832250&postcount=22
Overall experience while opening the HTC One (compared to the iPad 2/iPhone 3G/S/4S/iPod touch 5th/Motorola Atrix/Transformer Prime) I would give it a 4. The iPad being a 2 (almost impossible to open without a heat source and nearly impossible to mount a new glass without issues).
Uhuhu said:
After a trip to a shower
Click to expand...
Click to collapse
... Should I ask why?
To fix the purple tint caused by heat on the camera sensor. thats why.
chc31 said:
... Should I ask why?
Click to expand...
Click to collapse
After dropping my an old phone in the toilet (Before I went ) never again. My phone is barred from the bathroom unless its in my pocket. I guess the OP wanted to have some alone time with his phone.........................
chc31 said:
... Should I ask why?
Click to expand...
Click to collapse
TuneIn, on the upper part of the bathroom/shower (we mostly call it "box" to take a shower while listening to music.
Wow I think that this would be very usefull for other people who want open it...
Von Ropen said:
Wow I think that this would be very usefull for other people who want open it...
Click to expand...
Click to collapse
Well, it clearly isint. He just wanted everyone to know that he was able to open the phone.
Ok you did a pretty amazing job. Now let's move on.
Sent from my One using xda app-developers app
jags_the1 said:
Well, it clearly isint. He just wanted everyone to know that he was able to open the phone.
Ok you did a pretty amazing job. Now let's move on.
Sent from my One using xda app-developers app
Click to expand...
Click to collapse
Sorry you meant he was able to break the phone
Von Ropen said:
Sorry you meant he was able to break the phone
Click to expand...
Click to collapse
Phone is back. 100% working again. After opening it up I used a hairdryer on the "on/off" switch, left it open to cool down. After an hour I left it charging and left it there. It wasn't boot looping anymore and it turned on.
Uhuhu said:
Phone is back. 100% working again. After opening it up I used a hairdryer on the "on/off" switch, left it open to cool down. After an hour I left it charging and left it there. It wasn't boot looping anymore and it turned on.
Click to expand...
Click to collapse
But it is the same phone? how did you repare the top right corner of the screen that was completely off centered?
Von Ropen said:
But it is the same phone? how did you repare the top right corner of the screen that was completely off centered?
Click to expand...
Click to collapse
Same phone. I just glued it back to position with a superglue (superbonder is the trademark I've used). Used a toothpick to smear it gently and used some phone books to keep things in place. The top aluminum part was bent but the superglue is now holding it.
About the video, I'm not sure I'm willing to open it again. It would be awesome tho..
I have read that under the speaker grills there are screws holding it together.. did you encounter these screws?
twerg said:
I have read that under the speaker grills there are screws holding it together.. did you encounter these screws?
Click to expand...
Click to collapse
Found no screws. It's stuck together in one piece by some clips on the white border only. It's also glued around the same white border.
Follow-up: The phone is still working fine but not charging anymore. I'll wait to open it again later, in about two days or so, and than I'll video the process to see if there's something wrong. Hopefully it's fixable. And I hope I can open it without issues just like the first time. If it doesn't charge I'll see if I can get a new charging port (maybe the water did some damage by rusting the contacts of the port).
It seems that the phone is playing tricks on me. It's charging today.. Go figure..
Could be the water damage. I read where people with different phones talked about the phone acting weird like it just stop charging or the screen won't come on. That would come and go without warning. Remember my father in law damaged a phone once when he was a truck driver and delivering his load in to a walk in freezer. He made many trips in and out and I guess from the extreme cold to heat made it condensate inside the phone. Where are the water damage labels on the phone beings you had it open?
Sent from my Nexus 7 using Tapatalk 4
Double post.
Water labels are intact and since htc left Brazil we don't have an authorized to fix it so I opened it and saw that there is no water indicator in red. The water damage sticker is below the flash. Look at the pictures and you'll see a white sticker below the flash and another close to the usb port on the lower side of the phone. Not sure if the second one is a water damage indicator..
I'll keep using the phone till I get some alone time to open it. Tho I'm worried that I might break the phone this time (since it's working again - for no apparent reason).
So, yeah, there's an issue with the charging. Not sure if it's the port or the phone. Tested different chargers and it won't charge while it's on nor when it's off. After a day off it charged (yesterday) but now it won't charge. This sux. I have to find out what's going on. So, yes, I'll have to open it again. I can't have a phone that will be used to drive using gps all day behaving it like that. Phones won't last 4 hours on battery alone while using gps.
Added new picture with tools used..
Sorry for the double/triple post, but it's the best way to keep everyone informed..
If I helped you in any way please consider donating something so I can buy a new phone. The HTC One is dead due to an issue with the USB connector or something else that I'm still not aware. I will use this phone as a test bed from now on to see if I can fix other stuff without breaking too so I do need a new phone. You can donate here: http://bit.ly/1a9vqqg
Thanks and enjoy the video! I hope it helps a lot of people.
A video will be uploaded here: (it's 04:37am GMT -2) and still 205 minutes left to upload. Video will be 720p and it's 1.2gb so yeah, it will take a while. But now I'm off to bed. And sorry for my english. I'm ok writing but I'm so so when speaking. I said I would edit the video but since it's just shy of 19 minutes I figured I would leave it like that.
If you guys have any idea on what to do to help me fix the charging issue I would see if I can try that now that the phone can be easily opened. :fingers-crossed:

Really strange screen issue

Hi all
So I just installed a few games on my Nexus 4 this evening and noticed some areas of the screen not responding. Its isolated to about a 1cm from the left on my screen. When I enable the "show touches" option under developer options I can see the ball jump when I move my finger over the area. Whats odd is that the very edge reports OK and I can swipe to Google Now without issue.
I was using PA with Franco and just as a test revered to stock and it seemed to work however after about 5 mins it went back to the same behaviour. Once again I installed my stock nandroid and now its just jumping like it was. So confused!
I guess some software is running and causing issue or the screen is over sensitive in that area me touching it is causing issue. Its worth noting that I changed the screen a few days ago so it could be the connectors but could it be isolated due to a connection?
bert682 said:
Hi all
So I just installed a few games on my Nexus 4 this evening and noticed some areas of the screen not responding. Its isolated to about a 1cm from the left on my screen. When I enable the "show touches" option under developer options I can see the ball jump when I move my finger over the area. Whats odd is that the very edge reports OK and I can swipe to Google Now without issue.
I was using PA with Franco and just as a test revered to stock and it seemed to work however after about 5 mins it went back to the same behaviour. Once again I installed my stock nandroid and now its just jumping like it was. So confused!
I guess some software is running and causing issue or the screen is over sensitive in that area me touching it is causing issue. Its worth noting that I changed the screen a few days ago so it could be the connectors but could it be isolated due to a connection?
Click to expand...
Click to collapse
Ok so I was able to use the old screen (cracked) in a frankenstein fashion and it works 100% of the time. The current seen seems to work for a while and then goes back to missing that area.
Will try and return for a replacement.
bert682 said:
Ok so I was able to use the old screen (cracked) in a frankenstein fashion and it works 100% of the time. The current seen seems to work for a while and then goes back to missing that area.
Will try and return for a replacement.
Click to expand...
Click to collapse
Update 3
So the issue has progressed to being intermittent. It will be broken for a few hours, then work OK for a few. This can happen at random,so, not plugged in as I suspect heat was an issue. I can get a text, its broken, pocket the phone and in 5 mins when I get the reply it can be working again.
Ive made a video of what its doing, notice the white dot "jump" when compared to the right.
https://drive.google.com/file/d/0B0i6bdx3f4lWd3VmTWZXM0tjMTQ/edit?usp=sharing
Any suggestions?
You need a different screen if you want to fix it.
bert682 said:
Update 3
So the issue has progressed to being intermittent. It will be broken for a few hours, then work OK for a few. This can happen at random,so, not plugged in as I suspect heat was an issue. I can get a text, its broken, pocket the phone and in 5 mins when I get the reply it can be working again.
Ive made a video of what its doing, notice the white dot "jump" when compared to the right.
https://drive.google.com/file/d/0B0i6bdx3f4lWd3VmTWZXM0tjMTQ/edit?usp=sharing
Any suggestions?
Click to expand...
Click to collapse
Check that the flex cable isn't damaged, dirty or loose before you bother with a replacement. Either way, you probably need a replacement screen
lopezk38 said:
Check that the flex cable isn't damaged, dirty or loose before you bother with a replacement. Either way, you probably need a replacement screen
Click to expand...
Click to collapse
Yea I took it all apart and while the new one was connected I was able to connect the old one, upside down etc. It worked OK. Did a bit of a blow and properly pressing down on the connectors.
I could accept the screen is at fault at return it but when the issue is not 100% of the time I know my luck will be that when it gets tested at the sellers end it will work, get sent back to me and be broken again.
Have some monitoring apps running now so I can tell of its heat. Since this side is away from the battery im less incluined to think its heat from that. The motherboard does run down that side so it could be something in that? Ever seen any reports of that getting too hot?
Could even be heat from the antenna cable somehow?
Strange that it spans the whole length though.
Ill risk the return I think, got a video of it being broken so will see what happens.
Run over to Radio Shack (or whatever the equivalent is in what ever country you're in - I don't know where you are) and find a product called Deoxit/Progold. Deoxit cleans the contacts from oxidation, Progold enhances conductivity. Or find something similar.
This stuff is great for blasting inside headphone jacks to get rid of the "scratching" when your plug gets moved around, to fix iffy USB connections, etc. A little goes a long way. I don't know if it'll solve your screen issues, but it's worth a try, and if it doesn't work, you can still use it on other things, so it's not a waste of money.
Planterz said:
Run over to Radio Shack (or whatever the equivalent is in what ever country you're in - I don't know where you are) and find a product called Deoxit/Progold. Deoxit cleans the contacts from oxidation, Progold enhances conductivity. Or find something similar.
This stuff is great for blasting inside headphone jacks to get rid of the "scratching" when your plug gets moved around, to fix iffy USB connections, etc. A little goes a long way. I don't know if it'll solve your screen issues, but it's worth a try, and if it doesn't work, you can still use it on other things, so it's not a waste of money.
Click to expand...
Click to collapse
Wow, that stuff isnt cheap. Lets hope a little does go a long way!
Thanks, have ordered a small bottle, will give it a go.
I noticed that my new screen is genuine LG (at least its stamped all over it) but the one I removed seems to be a 3rd party replacement. Its got some areas that "look cheap" in comparison. Its got a small foil coating over the flex cable where as the one I removed didnt. I assume its to protect and move heat away?
Few forum posts mention the use of 3rd party chargers....I have used a cheap one when I am in work. I have used in on my old HTC Desire HD and my Lumia 520 and never had an issue. Do you think it could have damaged the digitiser?
bert682 said:
Wow, that stuff isnt cheap. Lets hope a little does go a long way!
Thanks, have ordered a small bottle, will give it a go.
I noticed that my new screen is genuine LG (at least its stamped all over it) but the one I removed seems to be a 3rd party replacement. Its got some areas that "look cheap" in comparison. Its got a small foil coating over the flex cable where as the one I removed didnt. I assume its to protect and move heat away?
Few forum posts mention the use of 3rd party chargers....I have used a cheap one when I am in work. I have used in on my old HTC Desire HD and my Lumia 520 and never had an issue. Do you think it could have damaged the digitiser?
Click to expand...
Click to collapse
Interestingly enough , the original digitizer is wrapped with aluminum tape. Some knockoffs have a better cover in fact. They use a hard aluminum sheet instead of aluminum tape. Some knockoffs don't have that shielding which is bad because that tape is there to keep the IC from getting spammed with useless data by radio frequencies and such.
If you haven't dropped your device , i don'T think it is likely that there is a problem with the glass. It's most likely the IC.
You could transfer your old flex to your new glass which is easy but you need some seriously steady hands.
When you remove the glass from the frame , you will see the flex cable's contact zone. It's basically the part where it connects to the glass. If you heat that area up with a heat gun it's gonna come right off when the solder beneath melts. Take out the new one and the old one. You need a flathead tip for your solering iron , which is like a flathead screwdriver. Simply take some solder and spread that solder around the contact dots , don't worry it won't stick to the plastic but it will melt if you keep it at the same spot too much. When you're done spreading , there are two dots with which you can align your old flex cable to your new glass. Use some adhesive tape around the alignment dots and Align the dots with your flex cable (you'll know which dots when you see it because it's orange and kinda stands out) press it so the adhesive holds and then use your heat gun and melt the solder to the contact zone.
It's actually easier than it sounds.

Categories

Resources