So, flashing SBF 2.2 CEE everything was correct until SBF lite said 'please turn phone on manually' and I try but.. nothing happens. on the screen I just have the android word with a white blink just looping.
I tried and tried (to be sure it wasn't the damn button) but nothing happens
What do you recommend? disconnect USB cable? disconnect battery? I don't wanna brick it!
Edit: I disconnected USB and Battery, turned on phone, entered recovery (power + volume down) until i got the android with the ! orange symbol. Then pressed volume up +volume down and on that menu wiped the cache and data. after that reboot phone and it worked
Related
hi i have flashed cm902 rom it booted up but it dont like me cause makes eroros so i wanted ro reflash with old stock 2,3,3 and with recovery bootstrap i thinked what i wild came into recovery but it just hanged and now no recovery only white triangle with yelow! and only logo m, so maybe someone hav this problem earlier and can help me?cause now im searching half day of work for searching for solution.
thanks fo anny help
Dont worry. Do this. First use the wall charger and charge your phone for at least 30mins. So if your phone is off then it will charge till 70-80%. Check if it is charging by looking at the micro-usb port lighting up.
Now go to the White triangle with ! mark. Then press @ button. You will get options. Select erase data by pressing volume button and then clicking enter button on your keypad.
After the wipe has been done pull out battery. Then start RSD Lite on your computer. Put the battery to your phone. Now press both volume up and volume down together and then power button for 2secs. Leave power button. You will see it in bootloader.
Now load sbf file on RSD software and wait for it to recognize your phone. Then click start. Thats it. Your phone should be ok.
I was using cm10 2/11 for defy green lens.. I flashed indian froyo.. and it didn't boot up.. but when I connect to my comp it shows a white light... and gets detected in rsd lite.. so I flashed Chinese sbf .. den the phone was again black and not booting... not it is not getting detected on my comp but it is showing white led light.. plz help out...:crying:
Try this:
1. Pull out the phone battery
2. Put it back in the phone and press and hold volume down + power button and hold it for about 6-7 seconds, then release.
3. If a Robot logo appeared, you are lucky. Now press volume up + down at the same time, or press back button.
4. You should be in stock recovery now, touch Wipe data and then wipe cache. After that, press Reboot and the system should boot up
Also, a warning: I was flashing that chinese .sbf numerous times, and the result is bricked flashlight. So, flash it only when you need to!
markos807 said:
Try this:
1. Pull out the phone battery
2. Put it back in the phone and press and hold volume down + power button and hold it for about 6-7 seconds, then release.
3. If a Robot logo appeared, you are lucky. Now press volume up + down at the same time, or press back button.
4. You should be in stock recovery now, touch Wipe data and then wipe cache. After that, press Reboot and the system should boot up
Also, a warning: I was flashing that chinese .sbf numerous times, and the result is bricked flashlight. So, flash it only when you need to!
Click to expand...
Click to collapse
I tried the above... but actually i can't even get it to moto symbol.. its just blank black screen.. and now it only shows white led if i connect to comp... any other solution??
Well, you can try flashing another .sbf because I dont know what to do anymore
markos807 said:
Well, you can try flashing another .sbf because I dont know what to do anymore
Click to expand...
Click to collapse
Hey.. i fixed my defy... the battery was discharged totally.. so rsd lite wasn't detecting.. den i used a universal charger.. some chinese thingy.. which charged my battery.. :good: and rsd lite detected it...
Hi, My problem started when i tried to do some wipes to flash my phone:
My phone is a Defy 525 red lense with BL7 (Defy +)
While i try to do some wipes, like wipe data/cache, my phone seems to wipe data/cache for ever, never end or sometimes it just reset at the middle of the process.
Wipe cache just stay in wipe cache or ever.
I try to just flash with rsd lite the European not roored BL7, and it stuck at moto logo.
I try some wipes and the same happend.
Then i try to flash German Rooted BL7 and work, but its seems stranger while the phone start (the white screen with pinks letters seems to take more time than normal flash i do before), but the phone worked, battery was at 80%
Now i turn off the phone, i try some wipes, and the same happend, i just reset at the middle of the wipe data/dache.
I try again and my phone turn off and never turn on again.
Always with White Led.
My phone is no recognized by rsd lite and with the guides i follow like "connect usb the phone w/o battery, press and hold vol+ and power, connect the battery" and looks my computer seems the phone connected then "insttlling drivers" and after 2 secs it get disconnected, and drivers install fail.
Same for other metods like "press vol bot keys and power, connect battery, connect usb" or "connect usb, press bot vol and power, connect bat" or "press vol + and power, connect battery, connect usb"
I have 2.3.9 motorola drivers and rsd lite updated and not updated.
My battery seems to be fine, i tested it and looks with 80% charged.
And it was tested by another guy with 100% charged battery.
Thx for ur time Guys.
SebaS-DG said:
Hi, My problem started when i tried to do some wipes to flash my phone:
My phone is a Defy 525 red lense with BL7 (Defy +)
While i try to do some wipes, like wipe data/cache, my phone seems to wipe data/cache for ever, never end or sometimes it just reset at the middle of the process.
Wipe cache just stay in wipe cache or ever.
I try to just flash with rsd lite the European not roored BL7, and it stuck at moto logo.
I try some wipes and the same happend.
Then i try to flash German Rooted BL7 and work, but its seems stranger while the phone start (the white screen with pinks letters seems to take more time than normal flash i do before), but the phone worked, battery was at 80%
Now i turn off the phone, i try some wipes, and the same happend, i just reset at the middle of the wipe data/dache.
I try again and my phone turn off and never turn on again.
Always with White Led.
My phone is no recognized by rsd lite and with the guides i follow like "connect usb the phone w/o battery, press and hold vol+ and power, connect the battery" and looks my computer seems the phone connected then "insttlling drivers" and after 2 secs it get disconnected, and drivers install fail.
Same for other metods like "press vol bot keys and power, connect battery, connect usb" or "connect usb, press bot vol and power, connect bat" or "press vol + and power, connect battery, connect usb"
I have 2.3.9 motorola drivers and rsd lite updated and not updated.
My battery seems to be fine, i tested it and looks with 80% charged.
And it was tested by another guy with 100% charged battery.
Thx for ur time Guys.
Click to expand...
Click to collapse
Update drivers and RSDLite to v6.
hotdog125 said:
Update drivers and RSDLite to v6.
Click to expand...
Click to collapse
I was using "RSDLite6.1.4" before i try 5.6 and about "updated drivers" what drivers? i was using "MotorolaDeviceManager_2.3.9" i dont know what u mean with update drivers.
Atm im looking for updated rsd lite.
Thx for ur time.
Edit:
I uninstall all drivers and rsd lite, im isntalling "Motorola_End_User_Driver_Installation_5.9.0_64bit" and rsd lite 6.1.5
Edit 2: same result.
If you can't boot after BL7 flash and data + cache wipe from stock recovery, your phone may have a hardware issue
Sent from my MB526 using Tapatalk 2
I have a problem with my Motorola defy(non+). After i installed by mistake Android 4.4 with kernel 3.0 by Quarx, my defy wouldn't boot into the OS.
Tried to install another ROM but it ran into a problem and failed. Tried to install after that a new SBF because i don't know why the recovery menu was not there anymore.
Suddenly, after it finished, i noticed the phone won't power up anymore. It happened to me 2 times in the past and just adjusting the charger end into the phone carefully worked and i could power on the phone and install a different sbf and solve the problem but now it's different.
The phone won't power up with that method again.
When i connected the phone into the laptop the white led appeared, but without powering it on, RDS lite identified the device.
I installed a froyo 2.2.2 CEE sbf succesfully(it said) but it doesn't power up and now RDS lite doesn't recognise it either.(LED still works though)
What can i do?
urbanrazor said:
I have a problem with my Motorola defy(non+). After i installed by mistake Android 4.4 with kernel 3.0 by Quarx, my defy wouldn't boot into the OS.
Tried to install another ROM but it ran into a problem and failed. Tried to install after that a new SBF because i don't know why the recovery menu was not there anymore.
Suddenly, after it finished, i noticed the phone won't power up anymore. It happened to me 2 times in the past and just adjusting the charger end into the phone carefully worked and i could power on the phone and install a different sbf and solve the problem but now it's different.
The phone won't power up with that method again.
When i connected the phone into the laptop the white led appeared, but without powering it on, RDS lite identified the device.
I installed a froyo 2.2.2 CEE sbf succesfully(it said) but it doesn't power up and now RDS lite doesn't recognise it either.(LED still works though)
What can i do?
Click to expand...
Click to collapse
Try wiping data and cache in the stock recovery. To get into the stock recovery, power off the phone, hold in the volume- button then also press and hold the power button. After a few seconds you should see a triangle with an exclamation mark in the middle, and a little green android guy below that. Then press the volume+ and volume- buttons at the same time, and a menu should appear. Use the volume buttons to navigate the menu, and the power button to select an option. Select "wipe data/factory reset" and also "wipe cache partition". Then try to reboot the phone.
If the phone still won't boot, go into bootloader before connecting to RSD lite. To go into bootloader, power off your phone, then hold in the volume+ button and the power button at the same time. After about 5 seconds, release the buttons. The bootloader should display – it will show the version and a battery check. (If that doesn’t work, pull the battery, then put it back in while holding the volume+ and power buttons.) Then connect USB cable and use RSD Lite to flash sbf again.
Hi. So i kinda repaired my defy but it still has a problem. It does not want to charge without using MCGyver method. Everything else works fine, except the phone does not detect my battery so instead it shows a question mark. BTW i deleted by mistake the sbf but i know it was chinese. Only that sbf worked. Could you find me a good working sbf?
I was messing with my P10 Lite and I accidentally wiped the Vendor partition (not sure if I wiped anything else) with TWRP. After the phone rebooted it said something about a critical error during boot and went into erecovery. It gave me two options( I don't remember the second one) and I chose factory reset. It started doing it's thing but I guess something went wrong because it wasn't able to boot and it started to bootloop.
I managed to get into fastboot once. The bootloader and FRP should be unlocked but I am not sure as I think I semi accidentally used the command to relock the bootloader in the hopes of it doing the automatic low level factory reset. After that restart, the phone wanted to boot up but after the Huawei logo it went into the EMUI logo which I've shown in the pictures. Now I can't use any button combination and can't enter any menu. I also can't shut down the phone as it bootloops into the EMUI logo after I press the power button. I opened the phone and turned it off by detaching the battery cable but after holding the power down key and plugging the usb cable into the phone it still boots into the EMUI logo right after the Huawei logo.
I guess not being able to enter fastboot is the major issue and after hours of googling I am yet to find a solution.
Edit: I am a newb!
Please help!
Why did you delete the vendor partition, you could try plugging the phone into your computer and checking if you can do anything with fastboot while it's showing emui logo?
Alaunus said:
I was messing with my P10 Lite and I accidentally wiped the Vendor partition (not sure if I wiped anything else) with TWRP. After the phone rebooted it said something about a critical error during boot and went into erecovery. It gave me two options( I don't remember the second one) and I chose factory reset. It started doing it's thing but I guess something went wrong because it wasn't able to boot and it started to bootloop.
I managed to get into fastboot once. The bootloader and FRP should be unlocked but I am not sure as I think I semi accidentally used the command to relock the bootloader in the hopes of it doing the automatic low level factory reset. After that restart, the phone wanted to boot up but after the Huawei logo it went into the EMUI logo which I've shown in the pictures. Now I can't use any button combination and can't enter any menu. I also can't shut down the phone as it bootloops into the EMUI logo after I press the power button. I opened the phone and turned it off by detaching the battery cable but after holding the power down key and plugging the usb cable into the phone it still boots into the EMUI logo right after the Huawei logo.
I guess not being able to enter fastboot is the major issue and after hours of googling I am yet to find a solution.
Edit: I am a newb!
Please help!
Click to expand...
Click to collapse
Dload method. Put sd card in other phone or some card readers and put appropriate files.
nemanjsb said:
Dload method. Put sd card in other phone or some card readers and put appropriate files.
Click to expand...
Click to collapse
I've already tried that. I've placed the appropriate files into my SDcard but I can't use any button commands including volume up+down+power. When I press them my device just boots into the EMUI logo and nothing happens.
Edit: It boots into the EMUI logo even if I only press the power button. Pressing volume down + usb also boots me into the EMUI logo
DaarkZek said:
Why did you delete the vendor partition, you could try plugging the phone into your computer and checking if you can do anything with fastboot while it's showing emui logo?
Click to expand...
Click to collapse
I measured once and not trice before cutting... I was also not paying enough attention/in a hurry...
Power OFF the phone.
Press and Hold VOL Down and connect the phone to PC via USB cable. The phone should boot into Bootloader (fastboot mode). Does this method work?
or try this:
Press and Hold VOL Up and connect the phone to PC via USB cable. The phone should boot into eRecovey mode and then then select "Download latest stock rom and install".
Aalesund said:
Power OFF the phone.
Press and Hold VOL Down and connect the phone to PC via USB cable. The phone should boot into Bootloader (fastboot mode). Does this method work?
or try this:
Press and Hold VOL Up and connect the phone to PC via USB cable. The phone should boot into eRecovey mode and then then select "Download latest stock rom and install".
Click to expand...
Click to collapse
Ok, it seems like not all is lost about my phone. I managed to get into fastboot. In my situation, pressing volume down + usb cable while the battery was plugged into the phone did not work. That was before I opened up my phone's case and disconnected the battery cable.
As I mentioned before, I had opened my phone and disconnected the battery cable because that was the only way to shut it off.
What I did after I disconnected the battery cable was the following:
1 - Hold volume down and don't release it
2 - Plug in USB
3 - Plug in the battery cable into the phone's mobo.
That booted me into fastboot. Right now, the phone says my bootloader in unlocked and my FRP is locked. What would be the best way to flash the new stock OS on my phone?
Aalesund said:
Power OFF the phone.
Press and Hold VOL Down and connect the phone to PC via USB cable. The phone should boot into Bootloader (fastboot mode). Does this method work?
or try this:
Press and Hold VOL Up and connect the phone to PC via USB cable. The phone should boot into eRecovey mode and then then select "Download latest stock rom and install".
Click to expand...
Click to collapse
I have downloaded THIS and THIS for the new OS but by talking with Alexxxx1 in THIS discussion I learnt that Huawei has implemented a security patch in their latest update, which I've most likely installed, that prevents you from rolling back your OS version. That means I need to install the .386 version, which should be the last if I am not wrong, instead of the .378 correct? Though I heavily dislike patches like this I guess I can't do anything about that...