Related
Hi,
I was running CM10 on my defy and then i tried to update it with Quarx latest build and something went wrong....i was stuck at the motorola logo screen....
I used RSD Lite V5.3.1 to flash the stock rom to my defy and it still wont boot....its still stuck at the motorola logo....
Please help.....its booting only under the Bootloader mode (Power+Vol Up).....nothing else
Thanks
Shrewdy said:
Hi,
I was running CM10 on my defy and then i tried to update it with Quarx latest build and something went wrong....i was stuck at the motorola logo screen....
I used RSD Lite V5.3.1 to flash the stock rom to my defy and it still wont boot....its still stuck at the motorola logo....
Please help.....its booting only under the Bootloader mode (Power+Vol Up).....nothing else
Thanks
Click to expand...
Click to collapse
Did you flash the correct sbf?
How long are you stuck at the Motorola logo? Give a bit more information =P
It's most likely not bricked as it's almost impossible to brick the defy.. (I've never heard of it)
Please help
pk92 said:
Did you flash the correct sbf?
How long are you stuck at the Motorola logo? Give a bit more information =P
It's most likely not bricked as it's almost impossible to brick the defy.. (I've never heard of it)
Click to expand...
Click to collapse
Hi,
First i had upgraded to froyo and and used this link to get Gingerbread on my defy
http://forum.xda-developers.com/showthread.php?t=1285007
After that i installed many roms and the last one to be tried was CM10...which started all the problems...
I have now tried to flash rom from this link
http://forum.xda-developers.com/showthread.php?t=1386942
now it is booting up but now it is stuck with the animation screen....the phone actually does not start....
i know its something to do with the kernel but then i dont know which type of kernel to flash and how!!
Please help..
Let me know if you need any more information
Thank you....
Shrewdy said:
Hi,
First i had upgraded to froyo and and used this link to get Gingerbread on my defy
http://forum.xda-developers.com/showthread.php?t=1285007
After that i installed many roms and the last one to be tried was CM10...which started all the problems...
I have now tried to flash rom from this link
http://forum.xda-developers.com/showthread.php?t=1386942
now it is booting up but now it is stuck with the animation screen....the phone actually does not start....
i know its something to do with the kernel but then i dont know which type of kernel to flash and how!!
Please help..
Let me know if you need any more information
Thank you....
Click to expand...
Click to collapse
Red or Green Lens? Defy or Defy+?
If Red Lens then you can use Defy or Defy+ build straight from Froyo after installing 2nd init.
If Red Lens Defy with Defy+ build, you will need a battery fix
If Red Lens Defy with Defy build, nothing else needs to be installed
If Green Lens Defy, you can only use Defy build. Nothing else needs to be installed.
If Defy+ You can only use defy build, nothing else needs to be installed.
Download the defy/defy+ builds here:
http://forum.xda-developers.com/showthread.php?t=1768702
http://quarx2k.ru
There is also an SBF of CM10 here: http://forum.xda-developers.com/showthread.php?t=1691901
Thanks buddy
pk92 said:
Red or Green Lens? Defy or Defy+?
If Red Lens then you can use Defy or Defy+ build straight from Froyo after installing 2nd init.
If Red Lens Defy with Defy+ build, you will need a battery fix
If Red Lens Defy with Defy build, nothing else needs to be installed
If Green Lens Defy, you can only use Defy build. Nothing else needs to be installed.
If Defy+ You can only use defy build, nothing else needs to be installed.
Download the defy/defy+ builds here:
http://forum.xda-developers.com/showthread.php?t=1768702
http://quarx2k.ru
There is also an SBF of CM10 here: http://forum.xda-developers.com/showthread.php?t=1691901
Click to expand...
Click to collapse
i am downloading the CM10 sbf's for both Froyo and GB..
i will try to install each and will see which ones works for me....
Coz i have a defy and i think it is a red lense one.
But i had a GB kernel running on my defy....
I hope thinks get well with my defy....
Thanks, will update you as soon as something happens....
Nothing works
Shrewdy said:
i am downloading the CM10 sbf's for both Froyo and GB..
i will try to install each and will see which ones works for me....
Coz i have a defy and i think it is a red lense one.
But i had a GB kernel running on my defy....
I hope thinks get well with my defy....
Thanks, will update you as soon as something happens....
Click to expand...
Click to collapse
----------------
All hopes going down... I have flashed these sbf's from the link your provided but nothing works !!
1. Froyo-cm-10,JB.Quarx.30.07.build.Defyred/green.bl4.fixed'sbf NEW
2. A.2.3.6-cm-10,JB.Quarx-30.07build-Defy+/red fixed'sbf cm-10 bootanimation New
Infact i get an error at the bootloader itself Err: A5,70,00,00,23 (wonder whats that)
There is only 1 sbf that boots it up....but then my defy keep looping on the blur animation and never boots up....
SBF that works the most i got it from here
http://forum.xda-developers.com/showthread.php?t=966537
which was (4.5.1-134-DFP-1321 - retail-asia full Blur multilanguage Thread)
This works and atleast it sort of tries to boot up....
Also if i try to get into the recovery mode (Power + Vol Down)....i cannot see any options in recovery....just the small android exclamation image !!
Can you please help and get me atleast booted up till recovery ??
Thanks
Shrewdy said:
----------------
All hopes going down... I have flashed these sbf's from the link your provided but nothing works !!
1. Froyo-cm-10,JB.Quarx.30.07.build.Defyred/green.bl4.fixed'sbf NEW
2. A.2.3.6-cm-10,JB.Quarx-30.07build-Defy+/red fixed'sbf cm-10 bootanimation New
Infact i get an error at the bootloader itself Err: A5,70,00,00,23 (wonder whats that)
There is only 1 sbf that boots it up....but then my defy keep looping on the blur animation and never boots up....
SBF that works the most i got it from here
http://forum.xda-developers.com/showthread.php?t=966537
which was (4.5.1-134-DFP-1321 - retail-asia full Blur multilanguage Thread)
This works and atleast it sort of tries to boot up....
Also if i try to get into the recovery mode (Power + Vol Down)....i cannot see any options in recovery....just the small android exclamation image !!
Can you please help and get me atleast booted up till recovery ??
Thanks
Click to expand...
Click to collapse
I believe that little android guy is the stock recovery. From what I remember you hold both volume buttons and it takes you into stock recovery.
Unfortunately, you will no longer have 2nd init installed, which allows for CWM recovery, so you can't flash a zip from there.
How long does it stay stuck on the blur logo? Maybe you're just not waiting long enough? (Stupid question I know, but some people complain after 2 minutes, the first boot can take a long time!)
Try looking at This thread and see if the link which is in this post will work to download the Taiwanese SBF. For me it doesn't seem to load
Edit: - Oh the Taiwanese SBF did eventually download. Took about 5 minutes with the tab open loading. I've uploaded it to my Dropbox so you can download from there... should be a bit faster!
JRDNEM_U3_3.4.3-33-1_CHINESE_SIGN_SIGNED_UCAJRDNEMARAB1B50AA03A.0R_PDS03C_USAJRDNFRYORTINT15_P001_A013_HWp3_Service1FF.sbf.gz
(MD5 - 34E9A43EAB8D2FF6101536C4B3F104BD)
Note: This is Taiwanese, NOT CHINESE. The Chinese one burns out the flashlight and it cannot be used after that.
Still stuck
pk92 said:
I believe that little android guy is the stock recovery. From what I remember you hold both volume buttons and it takes you into stock recovery.
Unfortunately, you will no longer have 2nd init installed, which allows for CWM recovery, so you can't flash a zip from there.
How long does it stay stuck on the blur logo? Maybe you're just not waiting long enough? (Stupid question I know, but some people complain after 2 minutes, the first boot can take a long time!)
Try looking at This thread and see if the link which is in this post will work to download the Taiwanese SBF. For me it doesn't seem to load
Edit: - Oh the Taiwanese SBF did eventually download. Took about 5 minutes with the tab open loading. I've uploaded it to my Dropbox so you can download from there... should be a bit faster!
JRDNEM_U3_3.4.3-33-1_CHINESE_SIGN_SIGNED_UCAJRDNEMARAB1B50AA03A.0R_PDS03C_USAJRDNFRYORTINT15_P001_A013_HWp3_Service1FF.sbf.gz
(MD5 - 34E9A43EAB8D2FF6101536C4B3F104BD)
Note: This is Taiwanese, NOT CHINESE. The Chinese one burns out the flashlight and it cannot be used after that.
Click to expand...
Click to collapse
Thanks for helping me out....
The motorola logo stays around for 20 seconds after with the Motorola boot animation starts.....
So i left my defy on for around 20 mins and nothing is happening its still playing the boot animation. !!
I havent yet downloaded the sbf link you have given me as i am at work now and will be able to do that only when i reach home.
Another thing i have noticed is that i am able to charge my defy....that means the rom is present and hopefully working !!
What say....???
Have you done Factory Reset????
1- turn off your phone (take the battery out and then put it back in)
2- press and HOLD the volume DOWN button + power button
3- Motorola logo appears first, then after a few seconds an 'android ROBOT logo' appears
4- press volume UP and DOWN buttons at once, quickly
5- from the menu choose 'factory reset/wipe-format data'
6- then do 'wipe cache'
7- then do a reboot
see if it helps and you are able to start the phone normally
Euro your awesome!!
Euro_Rules said:
Have you done Factory Reset????
1- turn off your phone (take the battery out and then put it back in)
2- press and HOLD the volume DOWN button + power button
3- Motorola logo appears first, then after a few seconds an 'android ROBOT logo' appears
4- press volume UP and DOWN buttons at once, quickly
5- from the menu choose 'factory reset/wipe-format data'
6- then do 'wipe cache'
7- then do a reboot
see if it helps and you are able to start the phone normally
Click to expand...
Click to collapse
Hi buddy,
Thanks yaar...i did exactly you told me to and the phone booted normally...
thanks a million buddy...:good::good:
And i also owe a million thanks to pk92...you have been there when i need you the most buddy....:good::good::good:
Thanks...m so happy to see my defy come back to life... :laugh::laugh::laugh::laugh:
O god!! its been a tough time but i learnt something new too....
Thanks guys :laugh:
friend request !!
hi, pk92 & euro
i have sent you friend request...do accept if you like !!
Thanks guys...
Shrewdy said:
Hi buddy,
Thanks yaar...i did exactly you told me to and the phone booted normally...
thanks a million buddy...:good::good:
And i also owe a million thanks to pk92...you have been there when i need you the most buddy....:good::good::good:
Thanks...m so happy to see my defy come back to life... :laugh::laugh::laugh::laugh:
O god!! its been a tough time but i learnt something new too....
Thanks guys :laugh:
Click to expand...
Click to collapse
Hehehehehehehehe
You are Welcom Shrewdy
Say thanks to our awesome XDA developer's Because of them we are nothing...
Shrewdy said:
hi, pk92 & euro
i have sent you friend request...do accept if you like !!
Thanks guys...
Click to expand...
Click to collapse
Accepted :highfive:
Guys I have the same problem.
Phone was upgraded from Froyo to CM7 and took it fine. Played for a while in CM7 but decided to upgrade to CM10.
Followed the steps from this thread http://forum.xda-developers.com/showthread.php?t=1795647
flashed foryo Kernel
Flashed CM10-20120924-NIGHTLY-mb525.zip
Flashed Google apps
Cleared cache, cleared Dalvik
Phone boots but gets stuck at Motorola logo and after blue and green light it loops back again to the same sequence.
It's a Defy with green lens and it had stock T-Mobile Froyo (rooted) before flash to CM7.
I'm now back to CM7 as CM10 didn't want to work.
sorry didnt get you
czarekusa said:
Guys I have the same problem.
Phone was upgraded from Froyo to CM7 and took it fine. Played for a while in CM7 but decided to upgrade to CM10.
Followed the steps from this thread http://forum.xda-developers.com/showthread.php?t=1795647
flashed foryo Kernel
Flashed CM10-20120924-NIGHTLY-mb525.zip
Flashed Google apps
Cleared cache, cleared Dalvik
Phone boots but gets stuck at Motorola logo and after blue and green light it loops back again to the same sequence.
It's a Defy with green lens and it had stock T-Mobile Froyo (rooted) before flash to CM7.
I'm now back to CM7 as CM10 didn't want to work.
Click to expand...
Click to collapse
hey buddy...m sorry i didnt quite get you....
As per my understanding i believe your phone is working fine with CM7 installed and you want to install CM10 on your defy !!
am i correct !!
if you then let me make it clear that the latest CM10 build used a custom kernel made by quarx himself....it is not running a froyo or gb kernel...
so here is what you need to do....
1. simply factory reset your phone...clear cache and dalvik...
2. now flash the latest CM10 build
3. again...clear cache and dalvik...
4. and now let defy boot....first boot may take a longer time....
hope this works for u...if it does not...let me know...will b glad to help u...
Thanks
Shrewdy said:
hey buddy...m sorry i didnt quite get you....
As per my understanding i believe your phone is working fine with CM7 installed and you want to install CM10 on your defy !!
am i correct !!
if you then let me make it clear that the latest CM10 build used a custom kernel made by quarx himself....it is not running a froyo or gb kernel...
so here is what you need to do....
1. simply factory reset your phone...clear cache and dalvik...
2. now flash the latest CM10 build
3. again...clear cache and dalvik...
4. and now let defy boot....first boot may take a longer time....
hope this works for u...if it does not...let me know...will b glad to help u...
Thanks
Click to expand...
Click to collapse
Yes, you are correct. the phone is working fine with CM7.
Factory reset, you mean from boot menu or the hard factory reset with holding volume keys (procedure posted above in this thread)?
The first time I actually tried, I did flash of CM10 without the prior kernel flash and it didn't work either.
so do I need any kernel flash or do I just flash it with CM10 and it should work?
I'll try again later today or tomorrow.
Thanks
czarekusa said:
Yes, you are correct. the phone is working fine with CM7.
Factory reset, you mean from boot menu or the hard factory reset with holding volume keys (procedure posted above in this thread)?
The first time I actually tried, I did flash of CM10 without the prior kernel flash and it didn't work either.
so do I need any kernel flash or do I just flash it with CM10 and it should work?
I'll try again later today or tomorrow.
Thanks
Click to expand...
Click to collapse
Lots of us who had bootloops trying to flash CM10 24/09 with a BL5 base SBF solved the problem by flashing a BL6 base Froyo SBF.
But try a factory reset and flashing your stock T-Mobile Froyo first.
If your stock doesn't flash properly then it means you have inadvertently flashed something which updated your BL version to BL5.
I flashed the JDGC_U6.2.13.0 SBF which is BL6 and then I was fine.
Don't use this ROM though, just use it as a stepping-stone to install CM10.
Euro_Rules said:
Have you done Factory Reset????
1- turn off your phone (take the battery out and then put it back in)
2- press and HOLD the volume DOWN button + power button
3- Motorola logo appears first, then after a few seconds an 'android ROBOT logo' appears
4- press volume UP and DOWN buttons at once, quickly
5- from the menu choose 'factory reset/wipe-format data'
6- then do 'wipe cache'
7- then do a reboot
see if it helps and you are able to start the phone normally
Click to expand...
Click to collapse
Thanks a lottt.. :highfive:
Hi
I tried to update from from Eppy's JB 20120806 version.
I have a green lens MB525.
I believe I am running BL5. I think I used cm7.1.0-RC0-jordan-signed as my original SBF.
Up until this ROM I have had no problems updating from GB-ICS-JB.
After wiping cache & dalvik I installed the 11/10 version. All goes well and the boot changes to 2ndBoot.
I get Red moto logo, blue LED, then Red led then reboots or just stays with the red led and a blank screen.
Pulled the battery and I get the same.
I tried to load the 29/08 ROM and this did the same thing as well.
Do I need to update to BL6 or something?
I have returned the phone to the pre flashed state using the backup. So all is still working ok.
Any ideas and thanks for your help
Regards
A noob
vast524 said:
Hi
I tried to update from from Eppy's JB 20120806 version.
I have a green lens MB525.
I believe I am running BL5. I think I used gncm7.1.0-RC0-jordan-sied as my original SBF.
Up until this ROM I have had no problems updating from GB-ICS-JB.
After wiping cache & dalvik I installed the 11/10 version. All goes well and the boot changes to 2ndBoot.
I get Red moto logo, blue LED, then Red led then reboots or just stays with the red led and a blank screen.
Pulled the battery and I get the same.
I tried to load the 29/08 ROM and this did the same thing as well.
Do I need to update to BL6 or something?
I have returned the phone to the pre flashed state using the backup. So all is still working ok.
Any ideas and thanks for your help
Regards
A noob
Click to expand...
Click to collapse
You just have to wait for it to boot. The screen goes blank when the LED switched from blue to red on my phone, too, but then it comes back on after some time, with the bootanimation. At first boot I think that lasted for maybe even 20 seconds. Much shorter on later boots.
But that couldn't have happened with the 29th of August build... Maybe you left your phone set to boot from 2ndboot, while that built is supposed to work by booting from 2ndInit?
P.S. cm7.1.0-RC0-jordan-signed is not an SBF file, it's a custom ROM that comes in a flashable zip. SBF files are in .sbf format silly and are flashed to the phone from the PC via RSDlite. Just so you know!
niksy+ said:
You just have to wait for it to boot. The screen goes blank when the LED switched from blue to red on my phone, too, but then it comes back on after some time, with the bootanimation. At first boot I think that lasted for maybe even 20 seconds. Much shorter on later boots.
But that couldn't have happened with the 29th of August build... Maybe you left your phone set to boot from 2ndboot, while that built is supposed to work by booting from 2ndInit?
P.S. cm7.1.0-RC0-jordan-signed is not an SBF file, it's a custom ROM that comes in a flashable zip. SBF files are in .sbf format silly and are flashed to the phone from the PC via RSDlite. Just so you know!
Click to expand...
Click to collapse
Hi and thanks for the reply and help.
I left the phone on for about 10 minutes with only the red led on. There seemed to be no activity.
I did not check to see if the boot was set back to 2ndinit. Can try that.
I found this file 3.4.2_177-005_NORDIC it is a SBF. I may have used this to start with after rooting. It was over 14mths ago.
Regards
Update. Tried to install 2409 Rom and made sure that I wiped the cache & dalvik. Also checked that it was set to 2ndinit.
Still looped. So am unsure what is going on. Rather frustrating.
Hi, flash your sbf, then 2init and then flash your cm you want.
Gesendet von meinem MB526
Hey there, I've tried almost every method to boot up the new Quarx builds, but for me it's impossible to boot this ROM's on my Defy red lens.
I have pull out the battery, installed the fix for dead screens, flashed 2409 and then the 0610 kernel, but no result.
Also, I wasn't able to boot the last non 2nd-boot built, the 2409 CM10 Nightly so I'm using 1209.
The only thing that I haven't is flashing another .sbf, but RSDLite doesn't recognize my Defy and Windows also not, with the latest drivers of Motorola installed.
Please, if anyone knows how to help me, reply me as soon as you can.
Thanks in advance and sorry for my poor english.
http://forum.xda-developers.com/showthread.php?t=1818520 try it with this zip, it worked for me. just erase all and flash latest build.
Jelly powered.Defy
Thank you for replying so fast, but I have already tried that a couple of times before. Anyway, I'll try again.
More info about my problem: when I flash any of the 2nd-boot ROM's and boot into bootmenu and after that select again 2nd boot, the screen goes black, BUT the backlight of the buttons turns on. Does it mean anything ?
Thanks in advance
Sent from my MB525 using xda app-developers app
TinoSP said:
Thank you for replying so fast, but I have already tried that a couple of times before. Anyway, I'll try again.
More info about my problem: when I flash any of the 2nd-boot ROM's and boot into bootmenu and after that select again 2nd boot, the screen goes black, BUT the backlight of the buttons turns on. Does it mean anything ?
Thanks in advance
Sent from my MB525 using xda app-developers app
Click to expand...
Click to collapse
normal the buttons flash and after few seconds u see the boot animation.
tell me more about ur phone.
what bl? and what model mb525 or 526.
Jelly powered.Defy
AnTerNoZ said:
normal the buttons flash and after few seconds u see the boot animation.
tell me more about ur phone.
what bl? and what model mb525 or 526.
Jelly powered.Defy
Click to expand...
Click to collapse
It's an MB525 Red lenses(Bayer). I don't know what kind of BL has, it comes from the official Froyo ROM of Vodafone Spain, and after that CM7,
So close..but I waited when the buttons were on for about an hour or something and nothing happened, should I be more patient?
TinoSP said:
It's an MB525 Red lenses(Bayer). I don't know what kind of BL has, it comes from the official Froyo ROM of Vodafone Spain, and after that CM7,
So close..but I waited when the buttons were on for about an hour or something and nothing happened, should I be more patient?
Click to expand...
Click to collapse
if u wait longer ur battery run out of power! don't do this or u have to mcgyver it.
do the following
load the CM10 2nd boot new
load the new version 4 update
wipe ur device
install ROM + update
install Gapps ur want
restart phone, if u get red led longer than a minute, pull battery out for 5-10min and press power button when battery is removed.
put back the battery, and wait for the CM10 bootanimation.
if that not work ur bl is not compatible and u had to flash a higher one, it's known that some bl5 not work, u just had to flash a bl6 ROM. for the ROM just look at the thread were all roms in, there u can found ur bl version.
Jelly powered.Defy
AnTerNoZ said:
if u wait longer ur battery run out of power! don't do this or u have to mcgyver it.
do the following
load the CM10 2nd boot new
load the new version 4 update
wipe ur device
install ROM + update
install Gapps ur want
restart phone, if u get red led longer than a minute, pull battery out for 5-10min and press power button when battery is removed.
put back the battery, and wait for the CM10 bootanimation.
if that not work ur bl is not compatible and u had to flash a higher one, it's known that some bl5 not work, u just had to flash a bl6 ROM. for the ROM just look at the thread were all roms in, there u can found ur bl version.
Jelly powered.Defy
Click to expand...
Click to collapse
Ok, I'm gonna try it, but first, to ensure that I'm doing the steps right, I'm gonna ask you two things: With "wipe" you mean wipe data+cache+dalvik or with the defy_full_wipe.zip?
And till now, I have flashed the updates as a normal ROM, should I flash them as an update.zip ?
yes, it's an update.zip! just enter custom recovery and go to install zip.
and wiping with recovery is enought, i use the ultimate zip only if i get problems.
Jelly powered.Defy
I have just tried and it hasn't worked. Thanks anyways for you efforts. I think that my only possible solution is flashing a new .sbf, but Rsdlite doesn't recognize my Defy
Sent from my MB525 using xda app-developers app
have u tried a different USB slot?
if u flash an sbf, try the custom ones, they are great.
Jelly powered.Defy
Yes, I have tried in four different USB ports in my laptop and even Windows doesn't recognize it, it shows my Defy as a unknown device
Sent from my MB525 using xda app-developers app
hmmm... what OS u had on PC? had u tried reinstall Motorola drivers with reboot?
Jelly powered.Defy
same problem, green lense
I have the same issues.
I have a green lens defy, was able to flash every nightly version until the 0924 version. So in other words, the last ROM that I was able to get booted was the 0912 quarx CM10 nightly.
I have looked in all the threads I could find, searched as much as I could, tried every technique, and still can't get past the black screen with the red LED.
I absolutely cannot get it to work no matter what I try. I've seriously read at least half a dozen people's instructions and nothing works. NOTHING! I have not tried starting from a stock sbf because I'm satisfied just barely enough using the 0912 nightly.
HELP!
Try to restore your Nandroid backup. If it does not work use RSDLite on a clean OS and reinstall root access,2ndinit and CM10.
Sent from my MB526 using xda app-developers app
AnTerNoZ said:
hmmm... what OS u had on PC? had u tried reinstall Motorola drivers with reboot?
Jelly powered.Defy
Click to expand...
Click to collapse
I have Windows 7 Home Premium, and I have run RSDLite in administrator rights and even in compatibility mode. I didn't tried to reinstall drivers because I don't have much time right now, so I'll tell you.
nastys said:
Try to restore your Nandroid backup. If it does not work use RSDLite on a clean OS and reinstall root access,2ndinit and CM10.
Sent from my MB526 using xda app-developers app
Click to expand...
Click to collapse
Are you replying to bulbouscorm or to me?
it happens to me with win 7 ultimate that the driver I installed half year before was corrupt, pleas try reinstall.
it's really not often that a defy will not recognized on PC.
u can also try a Linux Live-CD to flash it from there. but I not know the tool for Linux, search on forum and u will find it
Jelly powered.Defy
nastys said:
Try to restore your Nandroid backup. If it does not work use RSDLite on a clean OS and reinstall root access,2ndinit and CM10.
Sent from my MB526 using xda app-developers app
Click to expand...
Click to collapse
I restored my backup from a ICS version, but then I kind-of bricked my phone so I had to flash the stock Eclair .sbf.
I was playing with my very dumb phone at work, now I'm home I'll try to update to the latest CM10. Fingers crossed!
EDIT: I flashed the 1018 nightly - this time the boot logo was a silver M instead of the google logo I've been used to. AAAAAND it's still giving me a black screen + red LED. I flashed the sbf, rooted, installed 2nd init, and then flashed the 1018 nightly, the update, gapps with some cache/dalvik wiping before and after the nightly-update-gapps flash
I'm trying again using the custom zip files to wipe everything instead of using the recovery menu. Also this time I'm using the minimal gapps instead of the 1011 version
AAAAND it didn't work. black screen + red LED. I'm really looking for help here. Should I have not flashed straight from the froyo-updated stock sbf to the latest jb nightly?
bulbouscorm said:
I restored my backup from a ICS version, but then I kind-of bricked my phone so I had to flash the stock Eclair .sbf.
I was playing with my very dumb phone at work, now I'm home I'll try to update to the latest CM10. Fingers crossed!
EDIT: I flashed the 1018 nightly - this time the boot logo was a silver M instead of the google logo I've been used to. AAAAAND it's still giving me a black screen + red LED. I flashed the sbf, rooted, installed 2nd init, and then flashed the 1018 nightly, the update, gapps with some cache/dalvik wiping before and after the nightly-update-gapps flash
I'm trying again using the custom zip files to wipe everything instead of using the recovery menu. Also this time I'm using the minimal gapps instead of the 1011 version
AAAAND it didn't work. black screen + red LED. I'm really looking for help here. Should I have not flashed straight from the froyo-updated stock sbf to the latest jb nightly?
Click to expand...
Click to collapse
I was getting the black screen + red LED too, but manage to get it to work.
1: I flashed 0924
2: Then wiped everything
3: Flashed the 1018 build.
4: Tried botting - red LED + black screen
5: Booted to recovery
6: In boot options, reselected 2nd boot.
7: Tried to boot - red LED + black screen
8: Removed the battery
9: Waited 5 mins (could be more)
10: Placed the battery back
11: Tried to boot - Success.
Most of this steps are not needed, but it is what made my Defy boot with the 2ndboot builds.
bulbouscorm said:
...
I had to flash the stock Eclair .sbf.
.....
EDIT: I flashed the 1018 nightly - this time the boot logo was a silver M instead of the google logo I've been used to.
...
Click to expand...
Click to collapse
the silver m is eclair bootanimation
something defiantly goes wrong with ur phone. u should upgrade to a froyo ROM with bootloader version 6, there are a few user had problem with older bootloader to run second boot builds
Jelly powered.Defy
Yes, use BL6, latest CM10 2nd init rom and wipe data,cache,dalvik before installing, then use Stable Recovery to install zip from sdcard->18.10 ROM then install zip from sdcard->update v4 then install zip from sdcard->Gapps, reboot twice and it will work.
Sent from my MB526 using xda app-developers app
EDIT: And remember to wipe everything before restoring a Nandroid backup.
- So I was updating to Quarx's 5th Nov build (2ndboot) and in the middle the flash my phone turned off and decided not to start up. (The battery WAS NOT drained)
- I started with this guide in order to get it back to life:
http://forum.xda-developers.com/showthread.php?t=1807899(I used the exact same files, even the sbf. I live in India and I couldn't find India's sbf in this list: http://sbf.droid-developers.org/umts_jordan/list.php)
- Everything went as excepted and I was back on 2.2.2, so I tried to flash Quarx's build again. (I installed gapps, and cleared everything twice, thrice). However, the phone stuck on a bootloop:
red Motorola logo -> blue led -> greend led -> blank screen -> repeat.I cleared the cache's, factory reset, etc etc. No use.
- So i followed the original method again to get back to 2.2.2 and then flashed ICS from Cyano's website. It worked! So I tried again to flash a CM10 release, but this time a PRE-2ndboot build - 24th Sep.
It didn't work either. So JellyBean is the evident problem, but it doesn't make any sense, right?
- I started agin and tried to flash a different sbf, I got to this thread:http://forum.xda-developers.com/showthread.php?t=1093352 and tried the sbf provided (they claim it to be the one for SEA, including India). However, even after doing a factory reset from the stock recovery and flashing this sbf, I got a brick. The phone won't start whatsoever. No bootloader, no recovery - zilch. Dead.
- I again went back to my original method and got back to ICS...Flashed JB -> Same bootloop as before.
- Somethings I have noticed:
1. On flashing, the internal memory shrinks to only 128MB. I tried a factory reset from within the phone, from custom recovery and from the stock recovery. The memory was still 128MB with about 40MB free.
2. When I return to stock, the phone is somehow pre-rooted. On running superOneClick it shows that it;s already rooted but I continue nonetheless.
3. I think MAYBE the low internal storage might be at fault since JB Gappa require a lot of space.. I have tried it with minimal gapps too.
4. I have flashed every sbf available for Asian countries...but the only one that works is the one from the first link provided.
5. The only thing I can do right now is get to 2.2.2 or ICS...So if someone can help me out, that's my current status.
PS - I have been at it for 3 straight days, so yea, I have tried just about everything and read every thread regarding this. I even had to jump start by battery once as it ran out in the middle of a sbf flash.
There s a chance you didn't installed JB the right way. Also you ca install it without Gaaps. Does 2nd boot got enabled in Bootmenu? Did you flashed the kernel accordingly?
if you have bl4 try one of my fixed sbf with 2ndboot
ex. 28.11JB.Quarx+jellyX.kernel
than make a data and cache format fom bootmenu
bootmenu/ CPU settings/ system tools/ format data and cache to ext3
reboot
hve the link in my signature
I think you need bl. 4 from an 2.3.4 sbf for defy
In my country there was as an official update to GB
Users posted prblems with bootloader 3 and 7 @ quarx cm10 2ndboot roms
MB525 red lense
Hi,
You can take one more try (if you wanna ) to flash 12.09 JB build - it shall work
If so then flash Nordic retail 2.2.2 or WE retail (U3_3.4.2-177 or 179 from here)and try again 2ndboot builds (for some sbfs the last pre 2ndboot, 24/09 was the first not working)
Flash then 5/12 and jb gapps, wipe dalvik cache and cache after flashing.
Concerning 128 MB free memory - I suppose you are talking about data partition, not a system. Of course it is too small - the same as prerooted phone - try another sbf
Okay, just to clear the air - I was running Quarx's 28th Nov build before this happened.
I solved the 128MB problem. I'm currently on ICS 4.0.4 on the 16/07 CM9 build. It now shows 1.7GB internal available.
The kernel version shows 2.6.32.9-gb08c3c8xxxx..xxx.
I'm going to try and flash the 5/11 CM10 build (2ndboot). But before that I would to confirm the procedure:
1. Custom recovery
2. Data/Factory Reset
3. Clear cahce, Dalvik cache
4. Flash 05-11
5. Flash gapps (?) gapps-jb-20121011-signed.zip?
6. Clear cache, dalvik
7. Reboot
Should I go ahead with this?
PS. I reached my current state by flashing the sbf and firmware provided in this post: http://forum.xda-developers.com/showthread.php?t=1807899
I'll wait till someone approves of this, I don't want to brick it again.
vinu.shukl said:
Okay, just to clear the air - I was running Quarx's 28th Nov build before this happened.
I solved the 128MB problem. I'm currently on ICS 4.0.4 on the 16/07 CM9 build. It now shows 1.7GB internal available.
The kernel version shows 2.6.32.9-gb08c3c8xxxx..xxx.
I'm going to try and flash the 5/11 CM10 build (2ndboot). But before that I would to confirm the procedure:
1. Custom recovery
2. Data/Factory Reset
3. Clear cahce, Dalvik cache
4. Flash 05-11
5. Flash gapps (?) gapps-jb-20121011-signed.zip?
6. Clear cache, dalvik
7. Reboot
Should I go ahead with this?
PS. I reached my current state by flashing the sbf and firmware provided in this post: http://forum.xda-developers.com/showthread.php?t=1807899
I'll wait till someone approves of this, I don't want to brick it again.
Click to expand...
Click to collapse
Ok, so you flashed JORDN_U3_97.21.51, which means 24/09 and 2ndboot builds will not work.
They could work before when you had 2.2.2 on board.
You need another full sbf, and as you flashed BL5 it means you cannot go back to froyo. You shall find working BL5 sbf or go to BL6 one like U3_4.5.1-134_DFP137 or 139
And procedure above is correct
Ps. Method from post given by you was found out a long time ago, when some ppl flashed first gingerbread and then needed to go back to froyo. It is not a proper one for all defy users with still valid warranty in most of regions
corrinti said:
Ok, so you flashed JORDN_U3_97.21.51, which means 24/09 and 2ndboot builds will not work.
They could work before when you had 2.2.2 on board.
You need another full sbf, and as you flashed BL5 it means you cannot go back to froyo. You shall find working BL5 sbf or go to BL6 one like U3_4.5.1-134_DFP137 or 139
And procedure above is correct
Click to expand...
Click to collapse
These are the sbf's I found pertaining tp your specifications:
http://i.imgur.com/muQdT.jpg
EDIT: But they are all in the DEFY-PLUS repository...can I flash them?
So I can use anyone of them?
Also, I don't know much about BL versions...So should I just download one of the above sbf's and flash it using RSD? Do I need a nandroid backup to go with it too?
The procedure I would follow would be:
1. Factory reset, clear cache's
2. Go into bootloader menu
3. Flash above sbf using RSD
4. Reboot ??
Should that suffice?
First: if you are red lense it is ok to flash BL6
If you are green lense, to have your camera working, you will need 2ndboot builds (CM9, 10 or 7)
You will probably need red lens battery fix to show correct percentage, no matter you have green or red lense then.
You can flash it even later, after flashing CM10 and gapps and checking how it works
I would choose Nordic retail
Sometimes you can have problems with rooting with SuperOneClick (version 2.3) - force close Motorola Portal before rooting and it shall work ok then
And nandroid backup is not very useful when changing BL version, at least you will not be able to restore all
I have a green lens MB525.
So I'm downloading Nordic Retail for MB526 and will flash it using RSD.
After that, I can straight away flash any cm10 build right? (like the latest 5th Nov)
vinu.shukl said:
I have a green lens MB525.
So I'm downloading Nordic Retail for MB526 and will flash it using RSD.
After that, I can straight away flash any cm10 build right? (like the latest 5th Nov)
Click to expand...
Click to collapse
Yes, just normal procedure with rooting and 2ndinit installation, then flashing CM10 and jb 4.1 gapps with all proper wipings
And as mentioned above probably battery fix will be required for proper percentage - you will see
corrinti said:
Yes, just normal procedure with rooting and 2ndinit installation, then flashing CM10 and jb 4.1 gapps with all proper wipings
And as mentioned above probably battery fix will be required for proper percentage - you will see
Click to expand...
Click to collapse
Okay!
Gonna flash it tonight...Finger's crossed. =D
UPDATE: Flashed the Nordic Retail successfully. On stock 2.3.6 right now. Going to flash CM10-20121205-NIGHTLY-mb526.zip
UPDATE: I tried rooting it using SuoerOneClick v2.3.3.0 and even killed Moto Helper from PC and chose 'None' from the USB connection menu on the device. This is what I got:
http://i.imgur.com/cokl3.jpg and after reboot http://i.imgur.com/arZzd.jpg
SuperOneClick stopped responding after that. I waited 10 mins but nothing happened...No input requested from the device. tried it again but with the same results.
What should I do? Try z4root?
vinu.shukl said:
UPDATE: Flashed the Nordic Retail successfully. On stock 2.3.6 right now. Going to flash CM10-20121205-NIGHTLY-mb526.zip
UPDATE: I tried rooting it using SuoerOneClick v2.3.3.0 and even killed Moto Helper from PC and chose 'None' from the USB connection menu on the device. This is what I got:
http://i.imgur.com/cokl3.jpg and after reboot http://i.imgur.com/arZzd.jpg
SuperOneClick stopped responding after that. I waited 10 mins but nothing happened...No input requested from the device. tried it again but with the same results.
What should I do? Try z4root?
Click to expand...
Click to collapse
You can try z4root, though I rooted it with SOC 2.3.1 without problem. It seems that rooting didn't even start. Try choose zergRush instead of Auto
Note that USB is changing to Motorola Portal every several seconds if you do not kill it from a phone and it stops the process. Go to app settings, choose all apps, force close Motorola Portal (or freeze it - do not remember if such option is available)
Have you choosed USB debug mode?
Eventually try factory reset from settings before rooting
corrinti said:
You can try z4root, though I rooted it with SOC 2.3.1 without problem. It seems that rooting didn't even start. Try choose zergRush instead of Auto
Note that USB is changing to Motorola Portal every several seconds if you do not kill it from a phone and it stops the process. Go to app settings, choose all apps, force close Motorola Portal (or freeze it - do not remember if such option is available)
Have you choosed USB debug mode?
Eventually try factory reset from settings before rooting
Click to expand...
Click to collapse
Okay...I rebooted the phone and the PC and re-installed the Moto drivers...success!
Installing SndInitDefy_2.3.apk
UPDATE: Booted into custom recovery. Factory/data wipe. Cache, Dalvik wipe. Installing CM10-20121205-NIGHTLY-mb526.
vinu.shukl said:
Okay...I rebooted the phone and the PC and re-installed the Moto drivers...success!
Installing SndInitDefy_2.3.apk
UPDATE: Booted into custom recovery. Factory/data wipe. Cache, Dalvik wipe. Installing CM10-20121205-NIGHTLY-mb526.
Click to expand...
Click to collapse
You are lucky :laugh: - for many users (probably depends on sbf flashed) SndInit 2.3 does not work, I still use 1.4.2
You can also flash this zip - it changes the ramdisk to the older version and helps in battery life
corrinti said:
You are lucky :laugh: - for many users (probably depends on sbf flashed) SndInit 2.3 does not work, I still use 1.4.2
You can also flash this zip - it changes the ramdisk to the older version and helps in battery life
Click to expand...
Click to collapse
I guess I had some luck coming my way after a week of real hard times...
I'm currently restoring all my apps... Do I install this like any other zip i.e. clear cache + dalvik -> flash -> clear cache + dalvik ?
Also, since we are on the topic of performance, what are the optimum CPU settings?
I'm currently using:
1200,900,600,300 - 62,47,32,17
Interactive CPU Governor
SIO I/O Scheduler
No changes in the Memory Managment options (i.e. zRam, purginf of assests and kernel samepage merging - all are turned off)
16bit transparency turned off.
vinu.shukl said:
I guess I had some luck coming my way after a week of real hard times...
I'm currently restoring all my apps... Do I install this like any other zip i.e. clear cache + dalvik -> flash -> clear cache + dalvik ?
Also, since we are on the topic of performance, what are the optimum CPU settings?
I'm currently using:
1200,900,600,300 - 62,47,32,17
Interactive CPU Governor
SIO I/O Scheduler
No changes in the Memory Managment options (i.e. zRam, purginf of assests and kernel samepage merging - all are turned off)
16bit transparency turned off.
Click to expand...
Click to collapse
The ramdisk zip is to be installed in a standard way, like any other zip, probably doesn't require wiping caches, but probably
I usually use zRam (18%) - I didn't notice any bigger battery drain.
KSM off
WiFi - change to never when screen is off - you can have wifi on all the time without special battery drain
And choose proper baseband for you region
And CPU settings are ok as above
Defy on BL6
Ok guys I give up. I read and tried pretty much all the options net offered. Here is the problem:
I have green lens MB525. I bought it second hand in INDIA, it was running ICS. I switched to CM7 and it was working flawlessly for good 6 months. I did a reset and then it got stuck at recovery and showered error in some directories. So i triedro redo the CM7 procedure and loaded zip on root of SDcard. It didn;t changed anything. I did flashing and wiping the dalvik cache and memory, tried again, and again it was the same story.
Then i tried trying different SBF and it always used to get stuck at logo, i didn't bothered reading more about issue and stupid me flashed JORDN_U3_97.21.51. After that it started showing error in bootloader. It shows bootloader 09.10, Err: A5,69,35,00,27. I tried to use previous SBF and it then completely bricked it, only white light and black screen. Only when i again flashed it with JORDN_U3_97.21.51 it showed white motorola logo and bootloader version and error. I read this thread and tried the two firmwares using BL5 and BL6 in that order and its logo had changed to RED Motorola logo, but again the same bootloader menu with its version and error.
I had battery issues too, since i have been thinking and trying on it for past 10 days. Since i have battery charger, i used to charge the battery separately and plug it back in before flashing using RDSlite 5.6.
As of now i am stuck with a paperweight which i can only flash. I tried pressing down volume button to get into recovery but no matter what button i press it always ends up in bootloader. All help will be appreciated.
Vycas
---------- Post added at 06:03 PM ---------- Previous post was at 05:48 PM ----------
corrinti said:
Ok, so you flashed JORDN_U3_97.21.51, which means 24/09 and 2ndboot builds will not work.
They could work before when you had 2.2.2 on board.
You need another full sbf, and as you flashed BL5 it means you cannot go back to froyo. You shall find working BL5 sbf or go to BL6 one like U3_4.5.1-134_DFP137 or 139
And procedure above is correct
Ps. Method from post given by you was found out a long time ago, when some ppl flashed first gingerbread and then needed to go back to froyo. It is not a proper one for all defy users with still valid warranty in most of regions
Click to expand...
Click to collapse
Ok guys I give up. I read and tried pretty much all the options net offered. Here is the problem:
I have green lens MB525. I bought it second hand in INDIA, it was running ICS. I switched to CM7 and it was working flawlessly for good 6 months. I did a reset and then it got stuck at recovery and showered error in some directories. So i triedro redo the CM7 procedure and loaded zip on root of SDcard. It didn;t changed anything. I did flashing and wiping the dalvik cache and memory, tried again, and again it was the same story.
Then i tried trying different SBF and it always used to get stuck at logo, i didn't bothered reading more about issue and stupid me flashed JORDN_U3_97.21.51. After that it started showing error in bootloader. It shows bootloader 09.10, Err: A5,69,35,00,27. I tried to use previous SBF and it then completely bricked it, only white light and black screen. Only when i again flashed it with JORDN_U3_97.21.51 it showed white motorola logo and bootloader version and error. I read this thread and tried the two firmwares using BL5 and BL6 in that order and its logo had changed to RED Motorola logo, but again the same bootloader menu with its version and error.
I had battery issues too, since i have been thinking and trying on it for past 10 days. Since i have battery charger, i used to charge the battery separately and plug it back in before flashing using RDSlite 5.6.
As of now i am stuck with a paperweight which i can only flash. I tried pressing down volume button to get into recovery but no matter what button i press it always ends up in bootloader. All help will be appreciated.
Vycas
@Vycas
The problems might be several, unfortunately even hd problem, but try this:
- try different USB cable, different computer, different USB socket - the problem can arise when signal transmission is poor. Sometimes reinstalling of motorola drivers also helps
- if above does not help try Linux computer instead of Windows one
Regarding sbf - well, as you received error after each sbf flashing there could be a hope that you still may have BL4 (but also you may have BL6) - start your above mentioned trials with BL4 sbf, which will give you camera also with CM7
Hi all
So, I have a problem with my Defy (MB525 green lens). The best will be, if I'll write my full story. Here is it:
Story
I had Defy with CM 10. It had bloated battery. I wasn't using it for 6 months because I have another phone.
Some time ago, I decided, that I'll give Defy to my grandfather. On Tuesday this week I bought new original battery. I put it in the Defy, and charge it. I could boot up my old system as I wrote, CM 10. While it was charging, I detected that I haven't got SD Card. On the other hand, I found some 4GB Samsung SD, which had my father in his Desire. The SD Card had 3 partitions, which I tried to delete, and make only one, with GParted. After I did it, Linux and Windows can't see it. (This is almost other problem, which I'm trying to solve here http://crunchbang.org/forums/viewtopic.php?pid=350683)
But, when I put the CD Card to Defy, in TWRP recovery I could see some strange symbols. I thought, that I can repair something when I wipe SD Card. When the battery charged, I decided to do factory reset and wipe SD card. Here is my first failure. In TWRP I went to custom wipe, and here I marked everything including system and I wiped it. Then I remembered that system is recovery too. TWRP wrote, that everything except SD-Ext and SD was wiped. I known that this will be a problem. Yes, after reboot only Motorola logo without recovery.
I think, there was only one option - flash SBF, which I did. I went to stock bootloader and with sbf flash in Linux, I flashed this:
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF.sbf
And than this:
CM7RC1.5_16_09_11_custom.sbf
After reboot, I got bootloop. I tried to replace battery, do factory reset but nothing helped. That time I haven't got working card, so I couldn't flash some zip via CWM recovery. Thus, I again flash another SBF, but I don't really remember which. Probably some official CEE Froyo however, I'm not sure.
After that and reboot, I got only black screen with white led lighting while USB was connected. When I wanted to go to stock bootloader, still black screen, but I can flash SBF, and while flashing, screen have brightness and text about flashing.
I knew that this is little hard brick. I again tried to flash other SBF which I have or I downloaded (yes, again I don't know which). One of SBFs which I flashed was some fixed Chinese SBF . That made my defy booting, screen working, but still bootlooping. I couldn't reach any recovery.
Again, I flashed other SBFs, CM's too but nothing worked and I got black screen again.
And this was end of my story.
Current situation
I have Defy (MB525 green lens), with unknown framework an it had only black screen and what only I can do, is break Defy with hammer or flash some SBF.
So, here is list of all SBF files, that I have downloaded and probably tried to flash: (No order)
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF.sbf
CM7RC1.5_16_09_11_custom.sbf
JRDNEM_U3_2.51.1_BLUR_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA030.0R_USAJORDANO2DE_P048_A015_HWp3_Service1FF.sbf
JRDNEM_U3_3.4.2_177-003_BLUR_SIGN_SIGNED_USAJRDNEMARAB1B8RTGB03A.0R_PDS03C_USAJRDNFRYORTGB_P019_A010_HWp3_Service1FF.sbf
DFPRC_U_4.5.3-109_DPP-6-7_SIGNED_USADEFYPRCB1B50AA00A.0R_JRDNGIBRRTGC_P025_A019_HWp3a_Service1FF.sbf
JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF.sbf
JORDN_U3_97.21.51.sbf
JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P011_A010_HWp3_Service1FF.sbf
4.5.1-134-DFP-132-gingerbread-BL6-fixed.sbf
4.5.2-109-DHT-22-gingerbread-BL5-fixed.sbf
3.4.2-177-003-nordic-froyo-fixed.sbf
3.4.2-179-002-tmobile-froyo-fixed.sbf
4.5.1-134-DFP-74-gingerbread-BL5-fixed.sbf
4.5.3-109-DPP-11-gingerbread-BL5-fixed.sbf
JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN.sbf
Probably that is all what I have.
I've read many topics with similar problem and guides, but nothing helped me, or SBFs were unavailable.
So, what have I to flash, or which guide to try, if I want working Defy?
Sorry for my not good English
Thanks
UPDATE
sterver1 said:
Wohooo!!
Story
After a long time (4 months)...
Accidentally today I found my favorite custom ROM - MoKee OS, for Defy. I said to myself: "Hm, I have some time... I'll try to flash this MoKee on my Defy and maybe it solve my problem with (not) charging/unknown battery for system."
I picked out box with Defy from drawer, wiped the dust, took the Defy and said: "Sh*t! I haven't got SD Card!" Fortunately I found one. I download MoKee OS zip on that SD Card, put it to Defy, booted to recovery and flash MoKee OS zip. (...with full wipe of course...) Then rebooted to system.
Uselessly. Still unknown battery. "Hmm, It doesn't matter. Maybe here are some new stuffs which can solve my problem." And I continued to finding something, that can solve my problem. After a while I found ROMs with new 3.0 Kernel by Quarx. HERE. I downloaded CM 11 EXPERIMENTAL with this kernel and update recovery and flashed them. I didn't read thread. After reboot system didn't boot up and TWRP was inaccessible. I found why when I read some posts from that thread. HERE. But I couldn't flash that zip via recovery because I couldn't open recovery. So I mount /system to USB from bootloader and added files from zip manually to /system partition. After reboot it jammed on booting up. But TWRP was accessible so I did full wipe and flashed CM 11 EXPERIMENTAL and than that fix zip by @lorcotti. After that it finally booted up and battery was working and charging!
And they all lived happily ever after. :laugh:
SO, If you have some problem as me (unknown battery after flashing GB SBF on MB525), try this:
1. Download recovery and some ROM from [Kernel][GPL] Development 3.0 Kernel and fix from this post.
2. Put all zips on your SD Card.
3. Boot up to recovery.
4. Flash update-recovery.zip.
5. Reboot to recovery.
6. Do full wipe.
7. Flash ROM with 3.0 Kernel.
8. Flash Fix.
9. Wipe cache and dalvik cache.
10. Reboot to system.
If you want, you can flash GAPPS via recovery too.
But this will not be for daily usage! 3.0 Kernel by Quarx have a lot of bugs!
Thanks all!
Click to expand...
Click to collapse
Yeah!
Today I again tried to flash chines SBF. This one: JDGC_U6_2.13.0 China Unicom Thread/Download !!!BL6 kernel !!!
JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF.sbf
...and now I have bootable phone . I read many topics again and I got to know how to aces stock recovery. So I made wipe on this chines ROM and I can boot without loop, but I can only do emergency call with SIM it is the same. So, now, I don't know, what have I to do/flash, how to root it and flash here custom rom. Can I use SuperOneClick if it probably haven't got turned on USD Debugging?
Back on black
So, I made sbf file with depacker...
CMG39 from JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P011_A010_HWp3_Service1FF
and all others from JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF except CMG31.
Than the bootscreen changed from chines logo to grey motorola logo and I got Bootloader (9.00) Error A5,70,39,00,27. After that I flashed another sbf and I got Error A5,70,00,00,23. Than I flashed DEFYPLUS_U3_4.5.1-134_DFP-231_CEE_ROOTED_No_Signed.sbf and now I again have only black screen. F*ck!
I tried to flash my made sbf and chines one (JDGC_U6_2.13.0_SIGNED_USAJRDNPRCB1B50AA039.0R_JORDANAPCNCU_P017_A042_M006_HWp3_Service1FF) too but nothing...
Really here is nobody who can help please??? I want give Defy as Christmas gift. :crying:
OK, so repetition.
What mistakes I've made
1. I wipe wipe all including system partition in TWRP without any flashable zip on SD card.
2. I continued with flashing original SBF, while I have usable CWM.
3. I flashed many no downgradable GB SBFs.
4. I flashed Defy Plus SBF on Defy.
I hope that there is still hope.
Somehow to downgrade, flash only CWM where I can flash nandroid backup or I don't know what else...
a gingerbread sbf should also work on green lens defy as there is no diff. in hw... instead the cam
have you tried a factory reset in stock recovery after sbf flash ?
Sent from my MB526 using xda app-developers app
Now, after all (which I tried) SBFs I get only black screen. I tried many GB SBFs too, but still black screen...
I'm going to try some another Poland SBFs and than if that won't work, I'll try to flash all in Froyo CEE SBF particularly.
Thanks for your response.
Once you've flashed GB stock sbf you can't go back staight to froyo or else
Read the beginners guide and the SBF matrix sektion carefully.. if you haven't...
Sent from my MB526 using xda app-developers app
DFP 231 has been flashed by you, so no froyo sbf will work. Black screen on dfp 231 indicates some eMMC problem, because bl version is highest(no error possible). IMHO only service centre can disable bl check or replace the main board to fix the problem
The problem should have been solved at the boot loop issue by wiping from stock recovery, no network solved by baseband/radio fixes. Check the rsdlite log file to confirm checksum/access errors. I think that the custom sbf somehow messed up either eMMC or efuse(less likely, unheard of).
For sdcard error wipe everything using hdd llf. If any error persists it's a hardware issue
Sent from my MB526 using Tapatalk 4
@bone101
I know, I read it few times, and I know how it is (not) working. But, after all GB SBFs I got only black screen, so maybe were not correctly flashed... I'm using Linux and here is sbf_flash for flashing SBFs, and in it I can't view informations about phone as in RSD Lite... But maybe, it will work in wine..
Do you now, that if I flashed GB SBF, I have to flash another GB to solve my problem, because no Froyo will work?
@thekguy
I know how I can solve others problems. Only what I need help to solve is black screen.
Can't I flash something which support that high BL or it won't work?
check if you get into Bl. modus
press vol. up & then power button
tell what you see
Sent from my MB526 using xda app-developers app
That's what I'm saying, the black screen problem occurs due to bl version mostly, and you have highest bl, so in theory black screen is impossible. Unfortunately I have never seen in this forum any defy recovering from black screen after flashing dfp231. Check rsd log from windows if possible. Froyo sbf cannot work under any circumstance. You must flash only gb sbf
Sent from my MB526 using Tapatalk 4
@bone101
When I acess bootloader I have only black screen... While flashing I can see
"SW Update
In progress.."
Ok, I have Windows notebook available... Here are device properites from RSD Lite:
IMEI/ESN/MEID: N / A
Technology: N / A
Software Version: N / A
Flex Version: N / A
Bootloader Version: v0x000910
DRM Version: N / A
AP Die ID: 173002052f066b010000dcff0200
BP Die ID: 0000000000000000000000000000
AP Public ID: d0d8842b4879dd27b9eb94f970fbeec252fcb2f4
BP Public ID: 0000000000000000000000000000000000000000
Click to expand...
Click to collapse
I'm going to try some GB SBFs here...
WOHOOO I've got it! I flashed 231_GR_SIGN_UCADEFYEMARAB1B80AA004.0R_PDS03C_USAJRDNGIBRRTCEE_P022_A022_Service1FF.sbf and now I have got bootable phone... I'm in the system. I'm going to root it and flash CWM and MIUI if it will work.
Really thanks for your help!
sterver1 said:
@bone101
When I acess bootloader I have only black screen... While flashing I can see
"SW Update
In progress.."
Ok, I have Windows notebook available... Here are device properites from RSD Lite:
I'm going to try some GB SBFs here...
WOHOOO I've got it! I flashed 231_GR_SIGN_UCADEFYEMARAB1B80AA004.0R_PDS03C_USAJRDNGIBRRTCEE_P022_A022_Service1FF.sbf and now I have got bootable phone... I'm in the system. I'm going to root it and flash CWM and MIUI if it will work.
Really thanks for your help!
Click to expand...
Click to collapse
I'm stuck in same problem, downloading this sbf you mention before, hope it works. Fu^kin defy, it sucks
@Alejandrissimo
Good luck...
I have another problem. Now, I have GB kernel. In original 2.3.6 GB on MB525 green camera don't work, and battery too. So, I thought that, when I flash Froyo kernel (CM) and CM7 I got back Froyo kernel and working camera and battery. Yes, this was not possible. After I did it and rebooted it I got Bootloader error. I flashed DFP-231 again. Worked.
Than I tried restore Froyo from nandroid which I found something here on forum. Than I flashed CM7 and bootloader error again.
Now I have CM7 by Maniac for defy plus which worked well except camera and battery... I know that here are many topics about downgrading, camera fixing and others but all which I read are bad in something for me...
Here are some options what I found but I don't know if I can use one:
Method 2: (BIG thanks to Jebrew again for this one)
NOTE: You are going to need CM7 for this one. CM7 Stable version recommended.
Click to expand...
Click to collapse
from http://forum.xda-developers.com/showthread.php?t=1216982
DOWNGRADE
If you come from Android 2.1 and never flashed Android 2.2 you can use the fixed sbf-files method. With this method you will have a option to downgrade to you personal stock Android 2.1 via direct sbf flash.
Click to expand...
Click to collapse
from http://forum.xda-developers.com/showthread.php?t=966537 but I'v ever flashed Android 2.2.
Or http://forum.xda-developers.com/showthread.php?t=1465436 ... This is better option but I have flashed full 2.3.6 SBF and here is:
It will only work if you never flashed a Android 2.3.6 full sbf.
Click to expand...
Click to collapse
So, how can I downgrade or repair battery and camera? I don't care whether I have got GB or Froyo kernel if I have working camera and battery.
have you tried cm11 ?
or ms2ginger by walter79
Sent from my MB526 using xda app-developers app
sterver1 said:
@Alejandrissimo
Good luck...
Click to expand...
Click to collapse
Working and rooted, thanks for your help
Alejandrissimo said:
Working and rooted, thanks for your help
Click to expand...
Click to collapse
please see your PN
sterver1 said:
@Alejandrissimo
Good luck...
I have another problem. Now, I have GB kernel. In original 2.3.6 GB on MB525 green camera don't work, and battery too. So, I thought that, when I flash Froyo kernel (CM) and CM7 I got back Froyo kernel and working camera and battery. Yes, this was not possible. After I did it and rebooted it I got Bootloader error. I flashed DFP-231 again. Worked.
Than I tried restore Froyo from nandroid which I found something here on forum. Than I flashed CM7 and bootloader error again.
Now I have CM7 by Maniac for defy plus which worked well except camera and battery... I know that here are many topics about downgrading, camera fixing and others but all which I read are bad in something for me...
Here are some options what I found but I don't know if I can use one:
from http://forum.xda-developers.com/showthread.php?t=1216982
from http://forum.xda-developers.com/showthread.php?t=966537 but I'v ever flashed Android 2.2.
Or http://forum.xda-developers.com/showthread.php?t=1465436 ... This is better option but I have flashed full 2.3.6 SBF and here is:
So, how can I downgrade or repair battery and camera? I don't care whether I have got GB or Froyo kernel if I have working camera and battery.
Click to expand...
Click to collapse
Congrats man! Seems that rsdlite on Windows is the most reliable solution. Now to fix everything just flash cm10 (jelly bean) or later rom. It includes fixes for camera and battery
Again, no downgrading bl(not even jtag will work)
Sent from my MB526 using Tapatalk 4
Oh, ok. I'll try it. Thanks.
Hmm, and than, can I flash CM7 by Maniac or JB/GB WIUI and fixes in CM10 will still working?
Ms2ginger is not good for me because it haven't got slovak language. I'll give defy to my grandfather.
//And now, in Quarx CM 10 my battery don't charge. I tried 2 chargers and charging via USB too.
In options, battery is still "60% - Unknown"
Alejandrissimo said:
Working and rooted, thanks for your help
Click to expand...
Click to collapse
Hehe, I'm glad...
sterver1 said:
Oh, ok. I'll try it. Thanks.
Hmm, and than, can I flash CM7 by Maniac or JB/GB WIUI and fixes in CM10 will still working?
Ms2ginger is not good for me because it haven't got slovak language. I'll give defy to my grandfather.
//And now, in Quarx CM 10 my battery don't charge. I tried 2 chargers and charging via USB too.
In options, battery is still "60% - Unknown"
Hehe, I'm glad...
Click to expand...
Click to collapse
There's a cm7 2ndboot build which should work for you. Try cm10.1 or above, problem should be solved.
JB wiui includes those fixes, as does cm7 2ndboot. I don't think that wiui GB has them. I would personally go for cm10.1 or above
Sent from my MB526 using Tapatalk 4