Database Users

Flashing a gingerbread ROM

Hi, I've had my vibrant for quite a while it's been rooted ever since day 1. However I just got got Clockwork Mod working on stock 2.2 KA6. I'm now ready to flash a 2.3or 2.3.4 ROM and I wanted to know how do I go about it. I not sure if I can just flash over the stock 2.2 or not. I also hope I wouldn't have to resort to ODIN, as every one of my last several experiences with it was not good at all. Someone please help me out!

Someone please help I just want instructions how I can upgrade from stock KA6 to a 2.3 or 2.3.4 ROM. I would like to be able to do this without ODIN.

Hey bud, I'm kinda new on this board and not a super geek, but I might be able to point you in the right direction.
First of all, there's not an official Gingerbread release, so if you want it, you'll want to jump over the Development board (just go up a level) and find a ROM that is in 2.3. I know that Cyanogen is, for example, and there are a couple more.
What I did was to use Clockwork to do a backup (called a nandroid backup) and then I downloaded Cyanogen and used Clockwork to flash it. Quite simple and it sounds like you're all set up and ready to go.
Be advised that on (I think all) the 2.3 builds, you will have to give up on GPS. I had Cyanogen briefly just so I could check out streaming Netflix, but I had a few glitchy things like Swype to fix and decided just to go back to my Bionix ROM.
Hope that helps! Use the Thanks button if it did.

You can now get GPS with GB roms. You can even get wifi calling. Follow the instructions for the rom you want. CM7 is very easy to install.
Sent from my SGH-T959 using XDA Premium App

Its very simple. Since you have CWM (clockwork mod) now installed its easy peasy.
What you want to do is find a rom... personallt im using the nightly builds of CM7... You can find it by going to the android development section of our phone...
Find the rom then download the .zip file and place it somewhere on your internal sd card. Dont put it on your external sd.
Then go ahead and reboot into cwm and clear ur data/cache. After that go ahead and install zip, choose zip file from its location, then install.
Once installed, reboot and viola!
Most of all read the installation insrructions listed as well so you dont screw up. Worst comes to worst and your not sure then stop what your doing and ask here!!
Good luck my friend
Sent from my SGH-T959 using XDA Premium App

Sweet! Really? Last time I put Cyanogen on my GPS was a no go. That was less than 2 weeks ago, but I will look into it again.
Peace

[Q] can you flash cm7 if you have froyo firmware running?

I'm not sure if anyone has asked this question but I can't seem to find anything about it. Well my mytouch4g is currently running froyo. Long story short I downgraded my firmware because gingerbread was giving me problems, its a long story so please don't ask lol. But I really like the look of the cm7 ice cream sandwich theme. I was wondering can I still flash this rom even though I'm running on froyo now?
Also can anyone give me a link to the cm7 ice cream rom or just the cm7 rom if I am able to flash it. I'm a little confused about which is the latest one.
thanks everyone. I'm a total noob when it comes to android. thanks again!

mytouch4gnoob said:
I'm not sure if anyone has asked this question but I can't seem to find anything about it. Well my mytouch4g is currently running froyo. Long story short I downgraded my firmware because gingerbread was giving me problems, its a long story so please don't ask lol. But I really like the look of the cm7 ice cream sandwich theme. I was wondering can I still flash this rom even though I'm running on froyo now?
Also can anyone give me a link to the cm7 ice cream rom or just the cm7 rom if I am able to flash it. I'm a little confused about which is the latest one.
thanks everyone. I'm a total noob when it comes to android. thanks again!
Click to expand...
Click to collapse
of course you can flash CM7...
this is the CM7.1.0 ROM
and if you want ICS: Creamed Glacier ROM
your phone has root correct?
if not, root it, and put on a custom recovery, i.e ClockWorkMod Recovery
after being rooted and having a custom recovery installed:
reboot into recovery
1) DO A NANDROID BACKUP!!!
2) wipe Data/factory reset, cache, and Dalvik (under advanced)
3) flash Cyanogenmod 7 ROM
4) flash additional gapps.zip (optional)
5) reboot (this can take a while, just sit tight and wait)
6) hit thank thanks button
Disclaimer: i WILL NOT be responsible for whatever happens to your device. PLEASE READ AND UNDERSTAND WHAT YOU ARE DOING BEFORE PROCEEDING.
hope this helps.

On some older versions of clockworkmod you had to switch recovery versions to move between froyo and GB. I actually soft bricked my phone on my first flash because I didn't think to ask this question. That, however, is no longer the case. Follow Saranhai's instructions and you should be safe.
Sent from my HTC Glacier using XDA App

[Q] Is my MS2 bricked?

Hello every body,
I have bought my ms2 yesterday and i have decided to dont root it, so i went to motorlas web site and update it to android 2.3.6. But after see the MUIU from will5 i changed my mind i decided to install this custom rom. So i tried Gingerbreak to root my device, but tha app doesnt work i run it and he stay foreer with the mesage that tha phone is being rooted and nothing happen, so i presse home button and it closed and the fone stayed ok. But the only way i know to root this fone with ginger was that app so i decidd to try downgrade my fone to froyo again. i downloaded RSD Lite, upgrade my bootloader from 70.12 to 70.13 and tryed to install froyo retail again, the process look good but when rsd show the message rebooting fone the fone do not reboot and after rsd shows progress complet (Pass), so since that my fone is dead, can turn on in any mod or do nothing any one can help me to save my fone? And after that try a working root method? Thank You and Sorry for my English

Please refer to this post
http://forum.xda-developers.com/showthread.php?t=1437682
You did exactly the same thing. Once you are on GB, you can't go back to Froyo. And don't worry your phone will be okay.
Sent from my MotoA953 using xda premium

Yeah i saw that some minutes after i post that xP, i will download gb and try install it, sorry for the post i should search in the forum before post it.
But that is still a question i can root my fone? with android 2.3.6? i really want to install a custom rom =) thanks you

gexk said:
Yeah i saw that some minutes after i post that xP, i will download gb and try install it, sorry for the post i should search in the forum before post it.
But that is still a question i can root my fone? with android 2.3.6? i really want to install a custom rom =) thanks you
Click to expand...
Click to collapse
use SuperOneClick from http://forum.xda-developers.com/showthread.php?t=803682 to root your phone. make sure USB Debugging is on, plug your phone and click on Root menu in the app, then sit back and relax.
but without the ability to go back to froyo, MIUI is out from your custom rom Option as MIUI cannot run from GB kernel base.
however, there is CM7 http://forum.xda-developers.com/showthread.php?t=1338183 (and an inprogress CM9 http://forum.xda-developers.com/showthread.php?t=1374497) that you could try if you want to experience custom rom. functional wise, CM is better than MIUI (imho), but MIUI wins in fancy UI & themes.

thanks guys i think i will keep my phone with the default rom, i will only root it remove the unsued apps from TIM, and install a MIUI launcher. Did U think is a good ideia?

I don't think MIUI launcher works on stock ROM unless they have released a version compatible with all android 2.2 or 2.3
You can try Espier launcher from market. But it is more iPhone-ish than MIUI-ish.

Hard unlock Sim

I have asked to my telecoms operator the unsimlock code for my Defy, it said is yet unlocked but it is not
I have flash a full sbf 2.3.6. Before it was a 2.3.4.
Motorola can't give any code.
Is there a way to show to the operator that is still locked? Or a non paid way to have the unlock code (it's free with my operator)
I know that is a way to have a soft unock but only with cm7 or miui.
But i prefer a hard unlock for motorola rom.
THX.
Defy+ / 4.5.1-134_DFP-139 / 45.0.1390.MB526.Retail.en.FR
Bouygues telecom fr.

Always complain in a retail center. Take your defy, show him, let him call to services. Be persistent, not rude.
Indeed you could use a softunlock for CM7 or MIUI, don't know if you could for stock.

Thx for the answer. I have try this morning the softunlock with cm7 Nightly ( the only one cm7 i can install) but don't work . I think that the softunlock is only for 2.2.

Could you please try to install the nightly again and then flash the zip from my latest post on that threat?
Edit:
The zip
http://forum.xda-developers.com/attachment.php?attachmentid=908455&d=1329605492

Also you can try to write at russian forum - motofan.ru ( i'm not able to post link there...)
Just write IMEI and your model to them, probably you'll receive unlock code.
If you won't, only way is patch.

labsin said:
Could you please try to install the nightly again and then flash the zip from my latest post on that threat?
Click to expand...
Click to collapse
Thx. i have try but don't work anymore. I have flashed the cm7 zip, then, before reboot, flashed your zip. Trying to change baseband too but don't work.

Hellmanor said:
If you won't, only way is patch.
Click to expand...
Click to collapse
Yes, but for the moment not possible to find any patch for 2.3

Witch CM7 version are you using? Could you attach the files in defy_simlock_originals on your sdcard?

Could do the froyo for bl6 patch it from there and re install cm7
teamwork makes the dream work

labsin said:
Witch CM7 version are you using?
Click to expand...
Click to collapse
cm72-120127.0846-NIGHTLY-Defy+.zip
others don't work because of a 2.3.6 full sbf.
labsin said:
Could you attach the files in defy_simlock_originals on your sdcard?
Click to expand...
Click to collapse
Sorry but i don't understand what you want to say.
Could do the froyo for bl6 patch it from there and re install cm7
Click to expand...
Click to collapse
Do you mean to follow this way below? But i'm afraid this way don't work with Defy+?
Common Problems/Questions
Black Screens when booting up: (!) Tried to install a version of Android with a lower CG Version than the one currently on the phone.
Weird behavior after installing a Fixed SBF: Install a matching Nandroid backup with your SBF, and remember to clear Cache/Dalvik Cache using Recovery.
Installed full Gingerbread SBF and can’t go back to another rom: (!) aha! We have a issue here!, latest Stock Gingerbread full SBFs comes with a Version 5 of the CG, meaning until not long ago you were pretty much screwed. But wait, there is hope! A one kind Éclair has been found in China Defys that comes with Version 5 CG!.
How to fix it:
Download this SBF and Flash it
Root your Phone
Download 2nd Init 1.4.2 and Install ClockworkMod Recovery
Download and install this Nandroid Backup
Enter Recovery, Wipe Data/Cache
After wiping, turn off your phone
Turn it on and get immediately into Bootloader mode
Flash this Fixed SBF
Delete Data/Cache again and reboot.
You WONT be able to install full SBFs of any Éclair or Froyo since these Androids have lower CG Versions.
**NOTE*: I just rephrased the original post since it can be a bit confusing, it is linked as source below.
**NOTE2**: If you are using a non-Chinese defy, DO NOT USE THE CAMERA FLASH while on the Chinese rom, it WILL kill your LED.
Source: ((Original post here))
How to Install CM7 after Installing a Full Gingerbread SBF: (!) Ok, first of all do all the steps above on "Installed full Gingerbread SBF and can’t go back to another rom"
Root your Defy (Using SuperOneClick 1.7 and not 1.9).
Install SystemRecovery from GoAPK. If you install 2nd init, you'll just get into a boot loop and have to start over.
Reboot to recovery. Do a factory wipe, then do the cache wipe.
Install CM7 .Zip and then gapps zip file. DO NOT wipe again, you'll just go back to 2.2.2 CEE (if you accidentally do this, you can pick up again from step 3).
profit!
Click to expand...
Click to collapse

Yes it works with Defy+ if you are on a bld6 rom (not for the bld7 roms)
My patch from a couple posts back makes a copy of the patched file on your sdcard in the folder defy_simlock_originals. Could you post them here?
Don't know if the module works with the gingerbread kernel. That's why it is a good idea to try to get CM7 with froyo kernel. It's also handy if you wan't to install other roms (WIUI ...)
But could you fist give those files? Maybe i've made a mistake again ^^.
Edit:
Sorry you don't have the right guide. That one is for bld5 downgrade.
Here is for bld6: http://forum.xda-developers.com/showthread.php?t=1486731

labsin said:
My patch from a couple posts back makes a copy of the patched file on your sdcard in the folder defy_simlock_originals.Could you post them here?
Click to expand...
Click to collapse
Again, thank you for your help and time
(I have put .txt for upload)

The file is similar to the normal defy one as far as I can tell that must have done it... So prob. faullt of different kernel. You could try to downgrade and use CM7 on froyo kernel.

labsin said:
The file is similar to the normal defy one as far as I can tell that must have done it... So prob. faullt of different kernel. You could try to downgrade and use CM7 on froyo kernel.
Click to expand...
Click to collapse
Ok i'll try tomorrow

labsin said:
The file is similar to the normal defy one as far as I can tell that must have done it... So prob. faullt of different kernel. You could try to downgrade and use CM7 on froyo kernel.
Click to expand...
Click to collapse
I have change the kernel with THIS METHOD
after, try with WIUI 2.2.17: no network; then with update-cm-7.1.0-11-Defy-signed: no network, even when changing baseband.
So, if all that i have made is right, maybe it's not fault of kernel.
Other difference between MB526 and MB525?

You get 'no network' all the time, even with the sim from the right provider, also without the patch?
I think you're the fist to try on a defy+. Maybe look to the Russian fora...
edit: And can you tell me what your Baseband version is? (in settings > about)
edit2: If it is EPU93_U_00.59.01 Try it after installing RC1.5 from here: http://www.defy-cm.net/jordan-cm7.1-RC/

labsin said:
You get 'no network' all the time, even with the sim from the right provider, also without the patch?
I think you're the fist to try on a defy+. Maybe look to the Russian fora...
edit: And can you tell me what your Baseband version is? (in settings > about)
edit2: If it is EPU93_U_00.59.01 Try it after installing RC1.5 from here: http://www.defy-cm.net/jordan-cm7.1-RC/
Click to expand...
Click to collapse
no network only with wrong provider: with the patch no code ask, but no network even with other baseband.
Yes it is EPU93_U_00.59.01 (cm7.2 working on defy+ as well)
with RC1.5 no boot after files install, stuck on google logo.
Now i have flash fix sbf to use 2.3.6 rom because of no battery problems and better battery life. So i'll wait and ask again to my operator.
Now baseband is EPU_U_00.60.03
Do you think if i'm able to put a official operator rom it will see that is no desimlocked? i don't have made backup of my official rom (newbie mistake ) so i have ask here if it's possible with this method.

Blocking by TI OMAP 3630
I have read this:
Blocking the Bootloader by TI OMAP 3630
Why and how is it locked Defy?
While Linux is Open Source Motorola keeps the Defy the locked bootloader. Why?
For commercial reasons of course: avoid too many warranty returns from sorcerer's apprentices who brické their phone, for example (although care is denied you still have to manage the folders!) But also the traders (who manage some of the guaranteed returns, but not that ... we shall see below).
So Motorola maintains bootoader of our favorite phone is not locked and ready to unlock the last views of Roma making the switch to SBF rootage and even more difficult. But the fact how this lock is it made?
Unlike other phones (other brands, but also other brand models *) easy to unlock, the Defy is equipped with a TI OMAP 3630 chip that manages its technology via "M-Shield technology 'in this block. So we did not do a software problem but rather a problem if one CPU is addressing this release.
This technology also manages the simlockage phone which also explains why the operators are far from favorable to the release of Defy.
No one arrived today to crack this lock: it should have the tool from Texas Instruments where he provided to authorized repairers to put the Motorola Defy mode "SE" (Systems Engineering) for this.
* These phones using Qualcomm chips or other, do not bénéfiecient techonologie the M-Shield and are much easier to unlock.
Click to expand...
Click to collapse
(Google trad) Or here in french

stucked at jrdan u97.21.51
I am new at this my defy went dead when tried to upgrade to 2.2 did not have backup. I searched the web and only jrdan u 97.21.51 will work and canot go back or change any more to any other roms. tried the rsd lite to flash diferent roms and nothing works. tried rom manager and 2ndinit recovery and nothing i get black screen. Is there anyway to get out of this? Please help

sion123 said:
I am new at this my defy went dead when tried to upgrade to 2.2 did not have backup. I searched the web and only jrdan u 97.21.51 will work and canot go back or change any more to any other roms. tried the rsd lite to flash diferent roms and nothing works. tried rom manager and 2ndinit recovery and nothing i get black screen. Is there anyway to get out of this? Please help
Click to expand...
Click to collapse
Wrong thread i think.
Have you try a wipe cache and data in stock recovery before rsdlite? see here how to do with Froyo

got a defy, what do i need to flash custom rom?

hi people,
i have a SE x10 mini and its flashed with latest naa kernal and CM7mini.
im swapping it for a motorola defy tomorrow and just want some general answers if possible.
i see on the cm7 instructions it says *Flash froyo* then from clockwork install the .zip. ( similar to x10 mini )
but what steps do i need to take once i get the phone?
do i need to root it first then install a custom recovery first? or can i just chuck the CM7.zip on the sd card and flash?
im a little confused as i have only owned this x10 mini and i know how to flash kernals etc to this phone, just confused with the motorola
any help would be appreciated
regards

come on, at least look at the big Q & A threads before burdening others. I saying this to you instead of answering your questin, so that you at least give the matter some attention yourselves.
May the search be with you!

lol,
i have been reading up.
im not sure on this froyo, eclair etc
how would i know what i have when i get it?
will it say froyo in settings?
with the x10mini its all pretty much easy, no need to find what version or anything, just download cm7mini flash naa and flash.
so im a little confused with the defy,
ive been reading up and understand enough,
but i take it the steps i take is
To root the phone
install the 2ins app to install recovery
then flash cm9?
or do i need to use RSD lite to flash the froyo rom first?
reading the faq is pretty straight forward but i havnt seen the phone yet ( played around with it) so im not sure of the version etc.
im in the uk

in settings it provide ur the Android version. 2.2.2 is froyo... but ... that's not the only problem. from were u buy the phone? reseller or from private
Jelly powered.Defy

From a shop. Swapping it
Sent from my mini cp using tapatalk 2

ok than ur don't had a problem with the bootloader! it's not that easy as for ur x10mini cause the locked bl in the defy.
in general section is a thread there u find 'custom' sbf files, that u can flash with rsd light. it's the easiest way to get a good ROM on the defy, in only one step. the files are all rooted and with 2nd init. from that point u easy can flash other ROM through CWM, only beware for higher bootloader. ur defy is maximum bl5 I think.
Jelly powered.Defy
Edit:
link: http://forum.xda-developers.com/showthread.php?t=1691901
Edit2: and before u ask, we don't can flash custom kernel, only custom ROM.

how do i find out what bl# i have?
will it say in rsd lite?
regards

dreamz12345 said:
how do i find out what bl# i have?
will it say in rsd lite?
regards
Click to expand...
Click to collapse
No, rsdlite cant say ur the bl version,
ur can use the tool u find in that post
and if ur dont speak chinese in that post u have the answer for the cryptic buttons :good:

First of all, what kind of defy will you get?
Defy, Defy+ or Defy Mini?
The steps to install a custom rom are very easy.
1. root your defy
2 install cwm
3. make a nandroid backup with cwm
4. download the Rom you want to install
5. reboot into cwm and install the Rom.
This is a short instruction. For details instruction go to the Defy developments threads. There you find detailed instructions, and how to install custom Roms.
Sent from my GT-P7500 using XDA Premium HD app

It depends on which rom that you want to install and if you have green or red lense (because of the kernel).
But you will find these infos in the instructions of the rom thread.