[URGENT! ] Headset and speaker at the same time, possible ? - Defy Q&A, Help & Troubleshooting

Hi, I had a problem with my headset, I saw on internet that if I put an aluminum ball in TRS connector of the phone (the hole), my headset will work. My headset are now fixed
But now there is no speaker anymore, (i guess that my phone now think that there is a headset in it), so I will not know when someone will call me, and I need the alarm the morning to wake up for school(most important) ! :/
So I'd like to know if there is an app or something like that which could enable speaker and headset at the same, to get the speaker back.
Thanks you it's very important !

Switching between speakers and headphone is actually done physically inside the jack. AFAIK, there's no way to enable both using a software.

andr0idfreak said:
Switching between speakers and headphone is actually done physically inside the jack. AFAIK, there's no way to enable both using a software.
Click to expand...
Click to collapse
Ah ok so bad :'(
Thanks

Related

Himalaya loudspeaker-sound lost, headphone-sound ok

I lost the loudspeaker-sound in my Himalya. It works using headphones. I think it may have to do with another set of headphone I connected to it, which was not original. Perhaps it put the device on permanent headphone mode. But then again it might not have anything to do with that.
Is there a Himalaya expert in Berlin - Germany who might be able to help me with it? I dread having to send it to the official reapir center, as I expect it to cost a neck and a hand.
Happened to me when I received a call whilst listening to music. I pulled the headphones out before answering the call, and then answered it. I could here them but they cvouldn't hear me. If you plug the headphones in again and remove them it solves the problem. Well it did for me anyway
I tried that. I doesn't do it. It doesn't matter what kind of sound, if Media Player file is played of phone ringing, only the headphones work. I think I need a dotor.
I have read a lot about the problem in others threads. It seems the headphone-jack can get stuck, not making a contact, which normally is being made and which turns the XDA back to speaker mode, when the headphone-jack is pulled out. Hereto:
1- What does that mean exactely? Which part is that, in what part in the on-board jack? If it had been bent out of place, is it possible to bend the part pack (at best without having to disassemble)? (I tried the ramming in and out, no go).
2- I looked at the non-original jack I had used and it is about 2 mm longer than the original. Might perhaps that explain it? Is there a part in the back that could have been bent out of place?
3- If indeed this was the problem (if the jack had been bent out of place, one way or another), would the microphone work? I can record using the dictaphone and the micophone also works during a call.
When we had himalaya's it happened to both of our devices (my wife and I had one each).
It appears the spring in the speaker can come loose. I used to bang mine (pardon the pun) on my palm and sometimes it would start to work. Then we broke the speaker protection shield, and this made it easier sometimes and hard to fix in others.
When I sold it, my friend took it apart as it was out of warranty, and as he is electrically minded, he find the dodgy bit, and soldered it to the device, and now works perfectly.
Yes! Thanks Jasjar. It worked after a bit of beating.
I found a detailed instruction of how to fix it permanently in another thread. Sounds complicated and dangerous but eventually I must do it.
ran2far said:
I have read a lot about the problem in others threads. It seems the headphone-jack can get stuck, not making a contact, which normally is being made and which turns the XDA back to speaker mode, when the headphone-jack is pulled out.
Click to expand...
Click to collapse
Sorry for kicking the topic, but this was the solution for me. I just poked in the headphone-jack with a little stick and tataaaa... my sound is back!
Sound lost problem
Hi all,
same happen to me, the sound stoped working (on my side it had nothing to do with the phone jack).
After the modifaication which is described in this forum i had still the same problem so i solder the loud speaker directly - still same problem...
After some time i flashed the device again, now it works, so on my side it was a software problem...
The device was 3 month out of power, but i think remove the battery and if the sound appears on startup (on first boot) but later not, then flash the os and it will work ...
kr
chw
XDA 2 sound problem...
Hi!
Plese help me!
I have strange problem with my XDA 2.
I bough it 2 days ago. It was in O2 network.
Now when I unlocked it for my network (polish ERA-GSM) I saw that when I'm calling I cant hear anything. Person from the other sight can't hear me too..
XDA have sound becose I used media-player ando other sound stuff, thats why I think that speaker is ok. Microphone is ok too becose I can record animations with sound.
So what should I do now? ;/
Plese help...
Just for reference:
A friend of mine had this 2020, and both Speakerphone and mic were not working.
When somebody called, the ringtone DID sound.
Anyway, bluetooth handsfree worked fine.
All we did was play with the jack, using the stylus! Not even headphones...
And now it works fine!
He says he'll never put phones on it again... lol
cu around!
Looking for more Info
Hi, please help me find which points in the MDAII Motherboard can I solder to disable the headphones and get the audio and mic back to the MDA.
After a while my headphone-jack is broken from the motherboard and now I only have the pin outs in it.
The device is working perfect, and I can use bluetooth headphones. I just don't have audio in the speaker and no mic without bluetooth.
I hope someone can tell me which of the red points en the picture can I solder to disable the headphones.
I just want to do this temporally until I get a replacement spare part for it.
Thanks
EDIT: 12-12-2007
I got it. Just joining 1 and 3 and you will get audio back to the PDA disabling the headphones jack.
Thanks anyways for reading this..
Did you find out what all the mboard pins are for the jack?
I have a dodgy jack and would like to take flying leads of the mboard jack to an external (easily changed) inline jack. Does any know what the 1 to 6 pins correlate to. I would like to still switch the audio via the external jack. Not bothered about the mic.
TIA.

No sound from speaker while calling

Hi ppl! Let's see if I can express my problem!
My wizard is having this problem:
The inside speaker doesn't work during a call, only loud speaker(hands free) works, or by handset or bluetooh speaker! Does any one have this kind of problem?
I've send this one to warranty but, i've got a stupid respond from HTC:
"....Dear Sr. You have used an illegal software that damage you HTC motherboad...". Uaaauuu I've never used any 3rd software on this one. after received this answer Yesterday I made the first update to this phone (install the XDA Mobile 6 Release 3) but the problem still there.
Does any one have some ideas?
Now a stupid question ? how many speakers does wizard have ? 2 ?
Thanks for your time.
Rui
A while ago i had a similar problem where the phone thought my wired headset was plugged in and would not send the sound to the speakers... Only the headset, so i put some music on and plugged the headset in and out pretty fast until the sound came out the speakers in the phone. I think it had something to do with the switch inside the jack port that controls where the sound goes. Anyway that fixed mine but im not sure whats happening with yours.
The wizard has 3 speakers
2 Stereo speakers, one on each side
1 Speaker for calling in between the flashing lights
intheloft said:
A while ago i had a similar problem where the phone thought my wired headset was plugged in and would not send the sound to the speakers... Only the headset, so i put some music on and plugged the headset in and out pretty fast until the sound came out the speakers in the phone. I think it had something to do with the switch inside the jack port that controls where the sound goes. Anyway that fixed mine but im not sure whats happening with yours.
The wizard has 3 speakers
2 Stereo speakers, one on each side
1 Speaker for calling in between the flashing lights
Click to expand...
Click to collapse
Thats very true, if headset is used often or used much of the time,then the clips inside the jack port get over stretched and won't come back to it's original place after the input jack of headsets is plugged out,thus,not allowing to pass through the voice to the speakers.
Hi again! thanks for your replay!
Yes it was true about the mini jack! A good cleaning have solve 50% of the case!
The sound now cames out from the 2 stereo speakers ! But not from the speaker for calling!
I'm start to suspects from the speaker! Is it hard to dismount the wizard ???
Regards ,
Rui
zabardast_1 said:
Thats very true, if headset is used often or used much of the time,then the clips inside the jack port get over stretched and won't come back to it's original place after the input jack of headsets is plugged out,thus,not allowing to pass through the voice to the speakers.
Click to expand...
Click to collapse
THANK YOU!!!
Thanks guys. Had the same problem and the cleaning seems to have helped for now.

Speakers dead - both phone speaker and ringer...

Hi everyone...
I just pulled out my headphone plug and now I can't hear any sounds over the Prophet's speakers - No ringtones, no system sounds, nothing. Not even the other person when I call someone...
Still works over headphones though...
So what's wrong? Is my headphone jack screwed?
Thanks in advance...
That is a commun problem with this equipment.
The spring on the plub doesnt work right with the time.
One solution is to to plub and unplug several times and then test it if it the the problem has been solved.
Prepare to buy a new headphones plug.
Thanks for the reply... so you're basically saying, there's a mechanical problem with the headphone jack? That's strange, because when I call the phone from a different one the ringer works fine. But when I call someone else from the Prophet, I can't hear a thing...
I think that the problem lies with a little metal pin/pad inside the jack hole on the prophet.
When you put the jack in, it depresses this little pin, and deactivates the speaker, earspeaker and microphone, and transfers that over to the headset. After a bit of usage, it appears that it can get stuck when you remove the jack, disabling the phone's speakers etc.
I find that shaking it/hitting it/ramming the jack in and out, whilst building up frustration, can remove stress. It also can have some effect on the problem.
I'm just waiting it out until my contract ends, and i get a new phone.
EDIT: Ah, and the prophet naturally rings out loud aswell when you have the headset in, so that's why you can hear it.
I had the exact same problem, I sloved it by rotating a pin inside the headphone jack and it is sloved the speaker worked. I inserted the headphone and it work thus i took it off and prophet worked as normal.
wish good luck 4 u

Use in Car through Aux in

hi,
I have been using a Nokia phone with a 3.5 mm audio jack to connect it to my aux-in of the car and listen to music as well as make or take calls. The phone mic picks my voice quite well and I hear back the calling party through the car speakers.
Does the same work with HTC Touch HD too?
Update: I have connected the HTC Touch HD to my car's Aux in and it works well with the THD's mic picking up my voice easily. I had echo on a couple of calls but would like to check for its recurrence to believe that's some problem with unit or with the connectivity.
Afraid not mate.
When you plug something in the earphone socket, it assumes there's a mic plugged in too, like when you plug in a hands-free kit.
I've got exactly the same setup and didn't click what the problem was the first time I took a call. I just sat there like a pratt, shouting "HELLO" at my phone! lol
There may be a software workround for this, but not that I'm aware of.
I use the same approach.. but currently even though I am using a Belkin cable to a pretty neat deck.. the sound is completely off.. Treble is too high.. and My faithful kenwoods which would handle the full Volume of my N95-2 with ease are now cracking up.
Any ideas??
I use the same approach.. but currently even though I am using a Belkin cable to a pretty neat deck.. the sound is completely off.. Treble is too high.. and My faithful kenwoods which would handle the full Volume of my N95-2 with ease are now cracking up.
Any ideas??
Ideally, you should have the phone volume at about 75% of its max (between the phone volume itself, and the volume on the music player application), and control overall volume from the deck. If it still sounds dodgy after that, mess about with the equalizer on whatever player you're using, or the htc audio booster.
If anything, mine's a little quiet, but I've not tried messing with output volume settings in Tweak HD. I tend to have to have my deck turned up about 70-80%, whereas I normally have the radio at about 20-30%.
johncmolyneux said:
Afraid not mate.
There may be a software workround for this, but not that I'm aware of.
Click to expand...
Click to collapse
Asking this question to all. Is anyone aware of any software to use HTC Touch HD mic while using a 3.5 mm headphones through its audio jack.
not both speakers and mic are off when in headset mode
it's a hardware thing
but like with htc headsets you can connect external speakers and mic to the conntors and it works
easy way is to tear the headset apart and solver in the stuff you want to the connector which came with the headset
johncmolyneux said:
Afraid not mate.
When you plug something in the earphone socket, it assumes there's a mic plugged in too, like when you plug in a hands-free kit.
I've got exactly the same setup and didn't click what the problem was the first time I took a call. I just sat there like a pratt, shouting "HELLO" at my phone! lol
There may be a software workround for this, but not that I'm aware of.
Click to expand...
Click to collapse
Mine works fine setup like this. I've got a 3.5m jack coming out and going into the back of my headunit. I can make calls without a problem. The phone seems to realise the connected jack doesn't have a mic so uses the internal one.
The first time I tried it though the person at the other end couldn't hear me but finally worked out this was because the cradle I was using was blocking the mic on the bottom of the phone! I quick readjustment of the cradle and everything was fine.
Sound quality when playing tunes has always been fine but the voice quality aint that great, the person at the other end sometime complains about echo.
crankshaft said:
The phone seems to realise the connected jack doesn't have a mic so uses the internal one.
Click to expand...
Click to collapse
Hmm.... I'll have to have a play with that then, as it was a total failure for me previously. I definitely didn't have the mic blocked, as my cradle holds the phone by the sides.
Cheers for that - I'll have a play about.
How about something like this?
http://www.overstock.com/Electronics/Audio-3.5-mm-Adapter-with-Microphone-for-iPhone/3440143/product.html?cid=133635
(iPhone example but googling "3.5mm microphone output" finds you more, all about £3)
"How about something like this?"
there is not standart for how 3.5mm jacks with mics work as in the width of the ring and such
doubt very very very much that iphone converter would work with anything but an iphone
Thats a good idea. I havent tried this myself but its not experience that the hadware needs an attached mic when plugging the 3.5mm into speakers. I use high quality headphones with no attatched mic to listen to music on the HD and can take calls via the phone or skype by using the headphones and the phone mic.
crankshaft said:
Mine works fine setup like this.
Sound quality when playing tunes has always been fine but the voice quality aint that great, the person at the other end sometime complains about echo.
Click to expand...
Click to collapse
Same setup as me for the last 12 months. I have to play around with the volume setting on the HU / HD all the time - its not ideal but the internal mic seems to pick up voice fine (and echo!).

[Q] Built-in mic muted when using TSR headphone

Hello,
when I plug-in my headphones (3.5" jack, 3pin TRS connector, no microphone) the phone thinks they have a mic and the built-in microphone is disabled and I cannot make calls (I could, but the other person would not hear my voice).
I did check with ddms and I've noticed that android does not detect any differences between TRS 3-pin connectors (w/o mic) and TRRS 4-pin ones (w/mic, like the one that ships with the phone):
Code:
08-12 17:58:59.340: VERBOSE/HeadsetObserver(531): Intent.ACTION_HEADSET_PLUG: state: 1 name: Headset mic: 1
so I though it could be a hardware limitation/issue or a kernel one. The status icon (Gingerbread 2.3.4) always shows a headset with a tiny mic, whether I connect a headset with mic or just standard headphones.
My question is: does this problem appear only on my blade (i.e. is my blade broken?) or is it a "general" issue present in all blades?
thank you for your help
slashdotted said:
My question is: does this problem appear only on my blade (i.e. is my blade broken?) or is it a "general" issue present in all blades?
thank you for your help
Click to expand...
Click to collapse
It's not just your Blade. I'm running stock 2.2 (got it today) and while there's no mic on the icon, the phone always disables the built-in mic even when I plug in regular headphones. Sound recorder and voice calls are both affected.
Have you found a workaround? I'd be OK without detection if the phone always assumed the attached headset doesn't have a mic and keeps the built-in one enabled.
Same here. Im on CM7 and even if i plug in the 3.5mm (3pin) headphones, the phone mic gets disabled and in the status bar i can see the icon of headset (no matter when i use headset or headphones).
Keeping this aside, i had a more worst problem. If i plugin any headphones or headset other than the stock one provided with phone, they wont fit in the socket correctly. Even if i push them tightly into the socket (and left) , they will come out by 1 or 2 mm making the headphones unusable (what happens is only one ear phone works). And both earphones work as long as i keep it pressed and held tightly into the socket. But i cant hold it all the time i was hearing to the music right...? WTF... And i figured out why this happens. This is due to the back cover which was designed foolishly. The back cover of phone has a tiny hole for headset jack which prevents the other 3.5mm headphones to completely enter into it (this is sure in my case). If i remove the back cover and plugin 3.5 headphones they will be fit completely without any problem (even though here i cant use the phone mic). Another foolish design of the back cover is the exposure of the power switch making it more vulnerable to damage.
I had an idea to cut out the extra plastic thing at the headset hole of back cover to make it usable with 3.5mm headphones, but i fear i would loose warranty. Will i loose the warranty if i do so..?
After watching all these i think the headset jack of our phone is not correct. It might be having difference in the connector lengths. Don't wanna blame the rom/kernel for this. After all those were just my opinions.
Exactly the same happens on my blade using default 2.1 rom that came with the phone.
As for the above post, perhaps you should see if you can get a new back cover? Its only yours having that issue
Sent from my ZTE BLADE using XDA App
Jack connector problem
bharat_xda19 said:
Keeping this aside, i had a more worst problem. If i plugin any headphones or headset other than the stock one provided with phone, they wont fit in the socket correctly. Even if i push them tightly into the socket (and left) , they will come out by 1 or 2 mm making the headphones unusable (what happens is only one ear phone works). And both earphones work as long as i keep it pressed and held tightly into the socket. But i cant hold it all the time i was hearing to the music right...? WTF... And i figured out why this happens. This is due to the back cover which was designed foolishly. The back cover of phone has a tiny hole for headset jack which prevents the other 3.5mm headphones to completely enter into it (this is sure in my case). If i remove the back cover and plugin 3.5 headphones they will be fit completely without any problem (even though here i cant use the phone mic). Another foolish design of the back cover is the exposure of the power switch making it more vulnerable to damage.
Click to expand...
Click to collapse
I have exactly the same problem with some jacks but not all (my headset from Nokia fits in well, a retractable jack I've bought for my car fits almost well (it never drops by itself but if you touch it to much, it does)).
The biggest problem I have is that some applications ("music" and "listen") start playing when the faulty contact happens, even if I was listening for music in another application (jamendo) this is really a pain because jamendo keeps playing music and a podcast starts to play in "listen". Is there a way to tell those applications not to react to the headset being plugged/unplugged ? (I guess the faulty contact may be acting like a remote control press or something...)
Thanks for your ideas
Edit : it seems related to this : http://forum.xda-developers.com/showthread.php?t=625731 and to this http://android.modaco.com/topic/301335-the-headphone-bug/ and it seems that this application : https://play.google.com/store/apps/details?id=com.idunnolol.headsetblocker&hl=fr can be used to configure the behavior. I'll try it tonight and tell if it solved the problem.
slashdotted said:
Hello,
when I plug-in my headphones (3.5" jack, 3pin TRS connector, no microphone) the phone thinks they have a mic and the built-in microphone is disabled and I cannot make calls (I could, but the other person would not hear my voice).
I did check with ddms and I've noticed that android does not detect any differences between TRS 3-pin connectors (w/o mic) and TRRS 4-pin ones (w/mic, like the one that ships with the phone):
Code:
08-12 17:58:59.340: VERBOSE/HeadsetObserver(531): Intent.ACTION_HEADSET_PLUG: state: 1 name: Headset mic: 1
so I though it could be a hardware limitation/issue or a kernel one. The status icon (Gingerbread 2.3.4) always shows a headset with a tiny mic, whether I connect a headset with mic or just standard headphones.
My question is: does this problem appear only on my blade (i.e. is my blade broken?) or is it a "general" issue present in all blades?
thank you for your help
Click to expand...
Click to collapse
Does any body found the answer/solution of this????
Sent from my Inspire 4G using Tapatalk

Categories

Resources