Hi everyone...
I just pulled out my headphone plug and now I can't hear any sounds over the Prophet's speakers - No ringtones, no system sounds, nothing. Not even the other person when I call someone...
Still works over headphones though...
So what's wrong? Is my headphone jack screwed?
Thanks in advance...
That is a commun problem with this equipment.
The spring on the plub doesnt work right with the time.
One solution is to to plub and unplug several times and then test it if it the the problem has been solved.
Prepare to buy a new headphones plug.
Thanks for the reply... so you're basically saying, there's a mechanical problem with the headphone jack? That's strange, because when I call the phone from a different one the ringer works fine. But when I call someone else from the Prophet, I can't hear a thing...
I think that the problem lies with a little metal pin/pad inside the jack hole on the prophet.
When you put the jack in, it depresses this little pin, and deactivates the speaker, earspeaker and microphone, and transfers that over to the headset. After a bit of usage, it appears that it can get stuck when you remove the jack, disabling the phone's speakers etc.
I find that shaking it/hitting it/ramming the jack in and out, whilst building up frustration, can remove stress. It also can have some effect on the problem.
I'm just waiting it out until my contract ends, and i get a new phone.
EDIT: Ah, and the prophet naturally rings out loud aswell when you have the headset in, so that's why you can hear it.
I had the exact same problem, I sloved it by rotating a pin inside the headphone jack and it is sloved the speaker worked. I inserted the headphone and it work thus i took it off and prophet worked as normal.
wish good luck 4 u
Related
I lost the loudspeaker-sound in my Himalya. It works using headphones. I think it may have to do with another set of headphone I connected to it, which was not original. Perhaps it put the device on permanent headphone mode. But then again it might not have anything to do with that.
Is there a Himalaya expert in Berlin - Germany who might be able to help me with it? I dread having to send it to the official reapir center, as I expect it to cost a neck and a hand.
Happened to me when I received a call whilst listening to music. I pulled the headphones out before answering the call, and then answered it. I could here them but they cvouldn't hear me. If you plug the headphones in again and remove them it solves the problem. Well it did for me anyway
I tried that. I doesn't do it. It doesn't matter what kind of sound, if Media Player file is played of phone ringing, only the headphones work. I think I need a dotor.
I have read a lot about the problem in others threads. It seems the headphone-jack can get stuck, not making a contact, which normally is being made and which turns the XDA back to speaker mode, when the headphone-jack is pulled out. Hereto:
1- What does that mean exactely? Which part is that, in what part in the on-board jack? If it had been bent out of place, is it possible to bend the part pack (at best without having to disassemble)? (I tried the ramming in and out, no go).
2- I looked at the non-original jack I had used and it is about 2 mm longer than the original. Might perhaps that explain it? Is there a part in the back that could have been bent out of place?
3- If indeed this was the problem (if the jack had been bent out of place, one way or another), would the microphone work? I can record using the dictaphone and the micophone also works during a call.
When we had himalaya's it happened to both of our devices (my wife and I had one each).
It appears the spring in the speaker can come loose. I used to bang mine (pardon the pun) on my palm and sometimes it would start to work. Then we broke the speaker protection shield, and this made it easier sometimes and hard to fix in others.
When I sold it, my friend took it apart as it was out of warranty, and as he is electrically minded, he find the dodgy bit, and soldered it to the device, and now works perfectly.
Yes! Thanks Jasjar. It worked after a bit of beating.
I found a detailed instruction of how to fix it permanently in another thread. Sounds complicated and dangerous but eventually I must do it.
ran2far said:
I have read a lot about the problem in others threads. It seems the headphone-jack can get stuck, not making a contact, which normally is being made and which turns the XDA back to speaker mode, when the headphone-jack is pulled out.
Click to expand...
Click to collapse
Sorry for kicking the topic, but this was the solution for me. I just poked in the headphone-jack with a little stick and tataaaa... my sound is back!
Sound lost problem
Hi all,
same happen to me, the sound stoped working (on my side it had nothing to do with the phone jack).
After the modifaication which is described in this forum i had still the same problem so i solder the loud speaker directly - still same problem...
After some time i flashed the device again, now it works, so on my side it was a software problem...
The device was 3 month out of power, but i think remove the battery and if the sound appears on startup (on first boot) but later not, then flash the os and it will work ...
kr
chw
XDA 2 sound problem...
Hi!
Plese help me!
I have strange problem with my XDA 2.
I bough it 2 days ago. It was in O2 network.
Now when I unlocked it for my network (polish ERA-GSM) I saw that when I'm calling I cant hear anything. Person from the other sight can't hear me too..
XDA have sound becose I used media-player ando other sound stuff, thats why I think that speaker is ok. Microphone is ok too becose I can record animations with sound.
So what should I do now? ;/
Plese help...
Just for reference:
A friend of mine had this 2020, and both Speakerphone and mic were not working.
When somebody called, the ringtone DID sound.
Anyway, bluetooth handsfree worked fine.
All we did was play with the jack, using the stylus! Not even headphones...
And now it works fine!
He says he'll never put phones on it again... lol
cu around!
Looking for more Info
Hi, please help me find which points in the MDAII Motherboard can I solder to disable the headphones and get the audio and mic back to the MDA.
After a while my headphone-jack is broken from the motherboard and now I only have the pin outs in it.
The device is working perfect, and I can use bluetooth headphones. I just don't have audio in the speaker and no mic without bluetooth.
I hope someone can tell me which of the red points en the picture can I solder to disable the headphones.
I just want to do this temporally until I get a replacement spare part for it.
Thanks
EDIT: 12-12-2007
I got it. Just joining 1 and 3 and you will get audio back to the PDA disabling the headphones jack.
Thanks anyways for reading this..
Did you find out what all the mboard pins are for the jack?
I have a dodgy jack and would like to take flying leads of the mboard jack to an external (easily changed) inline jack. Does any know what the 1 to 6 pins correlate to. I would like to still switch the audio via the external jack. Not bothered about the mic.
TIA.
Hi,
I've noticed an audio output distortion of some frequencies when listening to music, in the sound coming out of the 2.5mm jack.
When the speakers on the device is used, there is no problem.
When I plug the headphone, there is sound output, I hear the music, but some frequencies are lowered so much that I can't hear the singers voice. When I unplug, the speakers work fine and I can hear the singer again.
In additon that, most of the background instruments can be heard as well as the backvocals, if they are female.
It's like the sound is being processed (like an equalizer) when I plug the headphone, some frequencies are lowered, given some echo, reverb etc.
I don't understand how this is possible. I am thinking of a hardware contact problem, but it's hard to believe if this is a hw problem.
I've tried two firmwares (2.16.x, 2.25.11.1) and made hard reset also. No result.
Any ideas?
Note: I can try to actually record the sound tonight if anyone wants to hear.
Best regards,
Fast
maybe try a different headset first?....could be a short in the cable, because what you are describing is a phasing issue with the headset speakers......
Thanks for the response Kiru,
Just tried a different headset plugging it into my HAMA 2.5 --> 3.5 adapter. same result.
I will try the original headphone came with the Wizard. If the source of the problem is the HAMA adaptor, this should resolve it. (i hope it is)
Could you please elaborate on the "phasing issue" ?
fastguy said:
Could you please elaborate on the "phasing issue" ?
Click to expand...
Click to collapse
Hmm....how can I explain.....Let's start with the speaker itself. A speaker has two terminals on it, one postive and one negative. What we want is to have the positve from the source (ie. Amplifier) to the positive terminal of the speaker, and the same for the negative. Since there is a pair of speakers, we want them to be hooked-up correctly. If hook-up correctly then the speakers are in phase with each other, and this is called constructive interference, hence in phase. When ONLY ONE of the speakers is hooked-up backwards, we call this destructive interference, hence being out of phase. Being out of phase causes frequencies to cancel or sound muffled. Hope you kind of get what I mean, but I highly doubt that this is the problem with headphones because heaphones nowadays rarely get manufactured with this problem. This is just the electrical part of phasing. Also, you can have one speaker, and it could sound out of phase because of the distance it is firing from walls or the shape of the room due to the reflections of sound, this is called acustical phasing.
A short in the cable, meaning the positve and negative wire are somewhat touching, can cause a similar effect, and I suspect that this is problem for you. As you now state that you are using an 2.5 to 3.5 adaptor, I would agree with you that most likey you have a faulty adaptor.
Hope this helps! and keep me posted!
Hi again,
Thanks again for the explanation Kiru, I know a bit of electronics so I got the problem.
However, I'm now home and tried to original headset, no result. The same problem is existing.
This makes me believe that I've broken something inside the Wizard which shortcircuits something. I'm very dissapointed.
Maybe the only way is now to buy a stereo bluetooth headset...
Thanks for your help
Any reason that you can't return to orange for repair/replacement?
PROBLEM SOLVED
I got this unit from priceminister second hand. It's origin is not France, I don't have a purchase receipt neither.
By the way, I solved the problem. I disassambled the unit using the info given in one of the posts in the forum. I played a little with the contacts, there was oxidation in the outer solders, i cleared them up etc, it 's working at the moment.
I'll post some pictures afterwards.
and I hope i will be able to reassamble it, I already have a piece of thing which I don't know where to put
I got the same problem. Was working fine for 2 months then all of a sudden the headphone plug is all messed up. Volume is all distorted I can sometimes hear a song but quality is no where near the original. Usually everything sounds echoed. I think something is wrong with the plug
I've had the same problem. The headphone jack on the Wizard is crap. If you have your Wizard in your pocket with an adapter, as you move, the adapter pries back and forth on the jack. This breaks the cheap jack.
If you want to listen to your Wizard as an music player, you should invest in a nice set of bluetooth headphones and only plug the jack in when the wizard won't be moved around a lot, like a home or car stereo.
I recommend Nextlink Spider headphones. They double as a headset and you can navigate through your library with the button on them.
MUSIC Speed
I got the same problem here. The SE stereo btooth headset isnt yet in our place.
Anyway, i experienced this one with ROM2.16 Imate. The sound speed or music speed seems to being played faster than normal. But when i tried to plug the 2.3-3.5 adopter and quickly pull it out, the sound is played in normal speed then. strange.....
are you all sure that the wizard has a stereo output ? I thought it was mono.
Anyway you can get earpieces and headphones with a 2.5mm jack so you don't need a 2.5-3.5mm adapter.
Maybe the contacts on your jack are not connecting properly with the internal contacts of your adaptor
hi, i got an imate jamin and i need to replace the audio jack were the handsfree pug in, do anyone know where i can find to buy this part please or if anyone had the same problem how did you solve it.
thanks guys!!
Dodgy Audio jack
My audio jack plug works fine BUT when I unplug the headset, the phone stays in headset mode i.e. no sound from the speakers. If I plug/unplug the headset a load of times it eventually goes back to normal.
Any ideas. My solution is never to use the audio jack!
Audio Jack
I've had two M600's which have done exactly the same thing, both replaced by Orange, I've now upgraded to an M700 and unlocked the old M600 with a PAYG sim and guess what that one has now lost speaker sound so that three with the same fault and this M600 has never had a headset plugged in.
Has anyone else had similar problems?
i had the same problem othillo before it broke so be carefull cause your is about to brake too, i mailed imate and they said the only way to fix it is to send it to them in dubai.. not relally keen to send it there .. but till today i havent find ther part any where it seems that imate dont send out parts ... as soon as i find an alternative i will post it here..
Is this problem caused by the connector itself or is it something else? If it is the connector I can buy a new one at the local hardware store and modify it a little bit to make it fit in my S200, probably going to replace it with an 3,5mm jack if that is possible...
it is caused by the connector in fact htc the original makers of the prophet on there new models they changed it to a usb connector for the handsfree i changed my connector many times with regulas 2.5mm connector but the sound doesnt work properly. what it does it comes out with out bass then when you push the talk button on the handsfree sound comes out good. another thing i noticed is if when you insert the jack plug in the connector and you pull it out a little bit the sound comes better and the talk button works, i know for fact cause i tried it that its not from the handsfee cause i tried it on another device and work properly. the actuall connector for them is different from what you find to buy even if you plug in normal 2.5mm headphone sound doesnt come out right . if you manage to make it work and modify the connector please post it here so who got the same prob like me can have an idea how to fix it... thanks
Audio Jack
Here is what the problem is:
Audio jacks have what is called a normally closed contact. Each contact point actually has 2 parts. In the closed (no headset) the 2 part of the contact point make contact (shorts). This enables the signal to pass through the jack to the phone speaker. When you insert a headset, the 2 points open (break contact) and signal only goes to the headset.
I'm talking from experience as a sound engineer for over 30 years and this is usually the problem 99% of the time when it comes to these type of jacks. One of the contacts (usually the ground when no sound or mic at all) breaks or can no longer "spring" back. I haven't opened mine yet but fully expect this to be the problem.
audio jack
hi jsapper, i got what you saying and your absolutly right .. the thing i replaced mine 2 times now been done by a technician who fixes phones/pdas the thing with the connectors i replaced the device doesnt work properly sound comes out with out the bass and the talk button doesnt work .. i guess that the original part got some extra connectors or most probably the pins are switched around..
do you know if there is any special connectors for them...
I have a similar pb with my S200:
After running tomtom during 2000km installed on my motorbike w/ a 2.5mm headset, sound seems to no work anymore (neither back or ear speaker), I suppose that vibrations against jack connector are responsible.
With a bluetooth or wired headset sound works.
I have soft/hard reset, upgrade to last WM5 rom, upgrade to WM6 rom, I have tried to get in/out a 2.5mm jack connector without any result.
The ring facility is working (w/ or w/o 2.5mm jack connected), so I can say that the back speaker is working.
I am looking for a solution too...
nb: I have my back speaker + screen replaced one time after 2months.
Dean.
Have you try resolder the Connector?
it was to damaged to be resolded
Hi everybody,
I aswell have this kind of problem from time to time.My solution is quite simple.You have to use the original 2,5" jack with the 3 black "dividings".(sorry for my english) This solution reduced the problem dramatically.If the problem starts now, just plug it in and out a few times and it should work again.
Cheers
Phone Jack is a mechanical mess ...
Same prob, used the headset, rear speaker dead. I opened the prophet, unsoldered the jack and found it misconstructed.
The body of the jack is plastic and not capable to withstand the forces of a plugged in headset.
There are two integrated switches - which - when headset is unplugged are closed and deliver the signal to the speaker. one of the switches does not close anymore when the headset is unplugged. My first solution was to unsolder the jack and bridge the contacts 2 and 4 as welll as 3 and 5.
The rear speaker functions now and I can use the phone.
Next step will be to find a jack solution on the market to finally solve the problem. I will keep you informed!
thanks buzzi will be looking in here... for your post!
i had the same problem with my audio jack and i searched many forums for a solution. the only thing i can say: if you really want to use it and you want go back in normal mode after unplugging, take a little needle. if you look at the audio jack (USB is left to it) you have to stick the needle in the right side of the jack somewhere an search for a little contact (the first time hard to find, the second time easy) and try to push it a bit to the left. so the prophet goes back in normal mode. it sucks but i didnt find another solution...except for buying a bluetooth headset and use software to hear music over that (for mono headsets u can use a programm calles BTAudioToggel, but make sure u use the Toggle software, because there is another one called BTAudio, it sucks because it costs money and doesn't work for me so well)
Greetz
Friends,
My prophet has exactly the same symptoms. However, I opened up the phone and carefully examined the jack. It is crap, sure, but at least on my phone it is not at fault. I tested with a continuity meter and the contact mechanism was working perfectly. Those who tried this measure without success read the following thread:
http://forum.xda-developers.com/showthread.php?t=281331
In my case it is definitely a problem with the speaker, and it seems to be eqaully common. It seems that there is more than one problem dogging the speaker of ths model.
mine's got the small contact switch problem.
it started last night! SO Annoying. Plugging a friend's original 2.5mm adapter in and out solved it temporarily. Then it went again! I have only got a 3rd party 2.5mm plug, and it took me ages to trip the small switch back with that. I have now got a BT headset on order.
Can't wait for the newer design HTC headphone adapter as I have had this problem with 5 different devices! (Tanager, Typhoon, Hurricane, Tornado and now Prophet.)
would agree with hybrid the needle trick fixed it ran media player so i could tell when it was working again. it was mentioned before that using the 2.5mm adaptor with ibky 2 rings as opposed to 3 causes this problem. I can identify with this as i have been using my dopod h/free with no problems for months i use the adaptor to plug in my headphones one time and get a eap of issues!
i will adapt a h/free to plug in some nicer headphones!
Can i use the USB connection as a handsfree port on my prophet?
Cheers
Hi, Prophet's USB is not a USB hub and thus not usable for connecting external devices - only way is bluetooth ...
thanks buzzi
Hi everybody,
my wizard (with faria crossbow) is suddenly acting strange:
I plugged in my headset and listened to some music with media player, while i stopped listening received a call..
I've plugged out the headset but.... there's no sound coming out of the phone any more! Sound is only working through the headset... any help??
(I've tried adjusting the volume, resetting etc... without success!)
Could be mechanical damage to the headphones jack.
Try fixing it by putting a match there to unlock it.
sorry but what do you mean with: "by putting a match there to unlock it" ?
Try inserting and removing the headphone jack a few times, perhaps the contacts area bit bent and are shorting out.
well i've tried that.. doesn't work..
well suddenly after removing en inserting the jack a phew time the sound is working again... really strange but thx everbody
okeay this is really some mechinal flaw.. but its really annoying!!
While im calling and talking through the normal mic sometimes sound+mic stops working (and so the phone thinks theres a headset plugged in).
I know there is something inside the headphone jack that is not working correctly but I don't know what..
Is there a way to open the phone and fix this problem?
These things are great ! Dropped it on its head more than a few times and it still works !! Thanks to the xda-developer community for saving me having to get a new one !!
it was the headphones ;}
Hi ppl! Let's see if I can express my problem!
My wizard is having this problem:
The inside speaker doesn't work during a call, only loud speaker(hands free) works, or by handset or bluetooh speaker! Does any one have this kind of problem?
I've send this one to warranty but, i've got a stupid respond from HTC:
"....Dear Sr. You have used an illegal software that damage you HTC motherboad...". Uaaauuu I've never used any 3rd software on this one. after received this answer Yesterday I made the first update to this phone (install the XDA Mobile 6 Release 3) but the problem still there.
Does any one have some ideas?
Now a stupid question ? how many speakers does wizard have ? 2 ?
Thanks for your time.
Rui
A while ago i had a similar problem where the phone thought my wired headset was plugged in and would not send the sound to the speakers... Only the headset, so i put some music on and plugged the headset in and out pretty fast until the sound came out the speakers in the phone. I think it had something to do with the switch inside the jack port that controls where the sound goes. Anyway that fixed mine but im not sure whats happening with yours.
The wizard has 3 speakers
2 Stereo speakers, one on each side
1 Speaker for calling in between the flashing lights
intheloft said:
A while ago i had a similar problem where the phone thought my wired headset was plugged in and would not send the sound to the speakers... Only the headset, so i put some music on and plugged the headset in and out pretty fast until the sound came out the speakers in the phone. I think it had something to do with the switch inside the jack port that controls where the sound goes. Anyway that fixed mine but im not sure whats happening with yours.
The wizard has 3 speakers
2 Stereo speakers, one on each side
1 Speaker for calling in between the flashing lights
Click to expand...
Click to collapse
Thats very true, if headset is used often or used much of the time,then the clips inside the jack port get over stretched and won't come back to it's original place after the input jack of headsets is plugged out,thus,not allowing to pass through the voice to the speakers.
Hi again! thanks for your replay!
Yes it was true about the mini jack! A good cleaning have solve 50% of the case!
The sound now cames out from the 2 stereo speakers ! But not from the speaker for calling!
I'm start to suspects from the speaker! Is it hard to dismount the wizard ???
Regards ,
Rui
zabardast_1 said:
Thats very true, if headset is used often or used much of the time,then the clips inside the jack port get over stretched and won't come back to it's original place after the input jack of headsets is plugged out,thus,not allowing to pass through the voice to the speakers.
Click to expand...
Click to collapse
THANK YOU!!!
Thanks guys. Had the same problem and the cleaning seems to have helped for now.