Brick i917 1.3 while flashing MAGLDR - Focus General
hi to all!
phone: samsung focus 1,3 and original ATT rom (3.jpg)
i've tried to flash MAGLDR and then mi7. I wait MAGLDR (DFT_MLI_SAM1) istalling more then 15 min, but there was no progress, so i unpluged usb from PC. Now i can't turn it on, it's black sreen, but when i connect phone to USB, i can see samsung modem in Device Manager.
than i try to install AT&T and ROGERS original rom's, but i've got errors in WP7 Downloader Ver 7.21 (1.jpg) and WP7_Downloader_Ver_7.05 (2.jpg)
What can i do with it?
sorry for english and thank you)
Hi taitchi,
I had the exact same issue. Pulled out usb while magldr installation. There was no vibration when pressed power and even screen was off on mine. I put the phone in download mode by pressing up, camera and power. Phone did not show any life but still computer detected it. (Use different usb or cable or in my case different computer.)
Reflash magldr first. You will be good to go again. (flashing stock failed for me.)
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
prakash386 said:
Hi taitchi,
I had the exact same issue. Pulled out usb while magldr installation. There was no vibration when pressed power and even screen was off on mine. I put the phone in download mode by pressing up, camera and power. Phone did not show any life but still computer detected it. (Use different usb or cable or in my case different computer.)
Reflash magldr first. You will be good to go again. (flashing stock failed for me.)
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
thank you for your reply!
But yesterday i desided to try once more with WP7 Downloader Ver 7.41 for Publish, first 10-15 times i've got same error, as start post, but then COM3 connected successful and i've got this log:
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH UNLOCK
[Channel 0] FLASH UNLOCK Fail !!!
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH UNLOCK
[Channel 0] FLASH UNLOCK Success!!!
[Channel 0] Send Partition Table
[Channel 0] Partition Table is correct
[Channel 0] Erase MIBIB Region
[Channel 0] Write MIBIB Data
[Channel 0] MIBIB Download Success!!
[Channel 0] Erase FSBL Region
[Channel 0] Write FSBL Data
[Channel 0] FSBL Download Success!!
[Channel 0] Erase OSBL Region
[Channel 0] Write OSBL Data
[Channel 0] OSBL Download Success!!
[Channel 0] Erase AMSS Region
here it has stopped, and now i have got full dead phone( there is nothing in device manager, then I plug it to USB
i think, this problem was because of cable or my home PC, as on work pc I successfully flashed another i917.
I have the exact same problem. tried flashing the wp 7.8 o
taitschi said:
thank you for your reply!
But yesterday i desided to try once more with WP7 Downloader Ver 7.41 for Publish, first 10-15 times i've got same error, as start post, but then COM3 connected successful and i've got this log:
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH UNLOCK
[Channel 0] FLASH UNLOCK Fail !!!
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH LOCK
Detect COM3 Port
[Channel 0] Confirm Model Name
[Channel 0] FLASH UNLOCK
[Channel 0] FLASH UNLOCK Success!!!
[Channel 0] Send Partition Table
[Channel 0] Partition Table is correct
[Channel 0] Erase MIBIB Region
[Channel 0] Write MIBIB Data
[Channel 0] MIBIB Download Success!!
[Channel 0] Erase FSBL Region
[Channel 0] Write FSBL Data
[Channel 0] FSBL Download Success!!
[Channel 0] Erase OSBL Region
[Channel 0] Write OSBL Data
[Channel 0] OSBL Download Success!!
[Channel 0] Erase AMSS Region
here it has stopped, and now i have got full dead phone( there is nothing in device manager, then I plug it to USB
i think, this problem was because of cable or my home PC, as on work pc I successfully flashed another i917.
Click to expand...
Click to collapse
Same problem here. tried flashing the wp 7.8. ended with a infinite samsung logo loop. tried the above method. got the same error and a dead phone. tried all over the internet. nothing much found
focus 1.3 dead while installing MAGLDR
PLEASE PLEASE PLEASE PLEASE HELP ME GUYS
I had Focus 1.3 with official at&t windows phone 7 ORIGINAL
I tried to install MAGLDR,it was not responding at all so i unpluged usb it became a brick((
Now it doesn't respond to any keystrokes, charging, or connecting to PC
please any one help me please
---------- Post added at 10:43 AM ---------- Previous post was at 10:32 AM ----------
Help me out guys focus was full working but i was intalling magldr in download mode but it was unresponsive till 20 mins so i unpluged it now no keys rresponding and it is not switching on please help me guys
JTAG only...
I had the same problem.
Bring your phone to the service center.
Brick i917 1.4 while flashing MAGLDR phone stuck at samsung logo in pink colour
Brick i917 1.4 while flashing MAGLDR samsung logo stuck & its change to pink colour & error triangle change to MAGLDR is not responding its show error it can be format & access download mode.i try Samsung-i917-Focus-firmware-UCJK2-ATT-USA , Samsung-i917-Focus-firmware-UCJK3-ATT-USA_4K , Samsung-i917R-Focus-firmware-UXJL2-ROGERS-CANADA only ucjk2-att-usa & uxjl2-rogers-canada (Product_Force_Select_MD5_X) will work but still stuck at samsung logo after flashing & dft magldr allso not working it show
[Error Description]:
Please make sure that your device is connected to your computer.
also make sure that right drivers are installed (Active Sync or Windows Mobile Device Center)
Try to connect device to different USB port and also you can try to reboot PC.
Also you can try to exclude USB hubs.
[Info]: USBWorkDWPI.cpp (136)
please help me
thanks in advance
My 1.3 finished flashing alright. Did you make sure you had WMDC installed on your pc? I had to reboot my computer, initialize the MAGLDR installer on the pc and phone and only THEN connect the USB.
How did you do it?
euskalzabe said:
My 1.3 finished flashing alright. Did you make sure you had WMDC installed on your pc? I had to reboot my computer, initialize the MAGLDR installer on the pc and phone and only THEN connect the USB.
Click to expand...
Click to collapse
I can do all those things and even when the USB has connected and I try to flahs I get this error. Please help:
Please make sure that your device is connected to your computer.
also make sure that right drivers are installed (Active Sync or Windows Mobile Device Center)
Try to connect device to different USB port and also you can try to reboot PC.
Also you can try to exclude USB hubs
Click to expand...
Click to collapse
same here please find a solution
im also a focus user, i've tried all the possible things that i could do, still no use, the Samsung logo blinks,
im able to get into download mode, and not format mode, (it flicks off a second)
please help .. :crying:
jayadattasai said:
im also a focus user, i've tried all the possible things that i could do, still no use, the Samsung logo blinks,
im able to get into download mode, and not format mode, (it flicks off a second)
please help .. :crying:
Click to expand...
Click to collapse
I had screwed up my Focus when trying to update to WP 7.8 using the Seventh Eighter method. I was able to fix everything later and now I have Custom ROM running on my phone. I have put up all the steps I followed into a blogpost.
opensourcecollection.blogspot.in/2013/03/installing-windows-phone-78-on-samsung.html
Hope it helps! :angel:
Related
kill with flashing
I traing flash omnia with new rom with using WP7 Downloader Ver 7.41 and i do thomething wrong. When WP7 Downloader Ver 7.41 ask me "clean NVRAM" and i say Yes, after that phone is poweroff and do not respond fo any button. Kill i omnia??? does help me jig?
Clean nandroid?! Wtf? What was on the phone before?
I do not remember exactly, It was quickly, possibly NVRAM+something else. corrected the first post
One guy help my to repair boot with JTAG, but phone boot only to logo "omnia7". then every time when try flashing new FW I get masage "ERROR[Channel 0] Write FSBL Data Fail!!!" and phone poweroff until JTAG repair. WTF? How flash it? somebody have fullbackup fo JTAG (riff, z3x, ort)? Uploaded with ImageShack.us LOG Code: Open PDA image at : i:\wp7\i8700xenjk1\i8700 xen i8700xenjk1\signed_pda_cetus_europe.nb0 Open Phone image at : i:\wp7\i8700xenjk1\i8700 xen i8700xenjk1\signed_phone_cetus_europe.bin Open CSC image at : i:\wp7\i8700xenjk1\i8700 xen i8700xenjk1\signed_csc_cetus_europe_i8700xenjk1.csc Open Eboot image at : i:\wp7\i8700xenjk1\i8700 xen i8700xenjk1\signed_eboot_cetus_europe.eb0 Detect COM14 Port [Channel 0] Confirm Model Name [Channel 0] FLASH UNLOCK [Channel 0] FLASH UNLOCK Success!!! [Channel 0] Send Partition Table [Channel 0] Partition Table is correct [Channel 0] Erase MIBIB Region [Channel 0] Write MIBIB Data [Channel 0] MIBIB Download Success!! [Channel 0] Erase FSBL Region [Channel 0] Write FSBL Data ERROR[Channel 0] Write FSBL Data Fail!!! [Channel 0] FLASH LOCK camera + volume down + power do not work. werry sorry fo my English, I study
plz i have the same same same problem ---------- Post added at 06:48 PM ---------- Previous post was at 06:34 PM ---------- plz i have the same same same problem
excuse me why you say you are using version 7.41 and in the screen capture I see version 7.03
Flash successfull, logo stays at boot( Update) SOLVED
Finally Sammy came through....after tens of calls to Samsung, got the main-board replaced within warranty. It seems that the NAND eventually dies for each and every device, I was told. The downside is that they replaced it with a 8Gb, it was 16Gigs. Anyway, is it just me or anyone noticed that original Focus with the SD slot is waaayyyyy faster than OMNIA7 when it comes to updating trough Zune? I am having the freaking time of my life when I am near smashing an Omnia 7 Trying to help a friend ( I had a lot of Focuses but no Omnia so far): -device was on an boot loop- no downoad mode, no nada, just the Omnia7 logo flashingon screen - volume up+ camera+ POWER PUT IT IN DOWNLOAD MODE - it never said download mode on screen but the WP7 flash tool showed a connection under port 14 - flashed the files from I8700ORAJID flash succesfull STILL at boot logo, now it just stays there doesn't flash - I can put is successfully and properly in download mode - yellow triangle and so on. Open Phone image at : C:\omnia7all\signed_phone_Cetus_Europe.bin Open Eboot image at : C:\omnia7all\signed_eboot_Cetus_Europe.eb0 Open PDA image at : C:\omnia7all\signed_pda_Cetus_Europe.nb0 Open CSC image at : C:\omnia7all\signed_CSC_Cetus_Europe_I8700XECJJ6.csc Open CSC image at : C:\omnia7all\signed_CSC_Cetus_Europe_I8700DTMJJ6.csc Detect COM16 Port [Channel 0] Confirm Model Name [Channel 0] FLASH UNLOCK [Channel 0] FLASH UNLOCK Success!!! [Channel 0] Send Partition Table [Channel 0] Partition Table is correct [Channel 0] Erase AMSS Region [Channel 0] Write AMSS Data [Channel 0] AMSS Download Success!! [Channel 0] Erase DSP1 Region [Channel 0] Write DSP1 Data [Channel 0] DSP1 Download Success!! [Channel 0] Erase APPSBL Region [Channel 0] Write APPSBL Data [Channel 0] APPSBL Download Success!! [Channel 0] Erase CSC Region [Channel 0] Write CSC Data [Channel 0] CSC Download Success!! [Channel 0] Erase PDA Region [Channel 0] Write PDA Data [Channel 0] PDA Download Success!! [Channel 0] FLASH LOCK Detect COM16 Port IT STILL STAYS AT OMNIA7 LOGO and the WP7 flasher still shows a connection under port 16. Anybody with the same problem?
it seems that some roms are flashing and some are returning errors this is a 16G device... weird Open Phone image at : C:\Users\Eto\Desktop\I8700 XEN I8700XENJK1\I8700 XEN I8700XENJK1\signed_phone_Cetus_Europe.bin Open Eboot image at : C:\Users\Eto\Desktop\I8700 XEN I8700XENJK1\I8700 XEN I8700XENJK1\signed_eboot_Cetus_Europe.eb0 Open PDA image at : C:\Users\Eto\Desktop\I8700 XEN I8700XENJK1\I8700 XEN I8700XENJK1\signed_pda_Cetus_Europe.nb0 Open CSC image at : C:\Users\Eto\Desktop\I8700 XEN I8700XENJK1\I8700 XEN I8700XENJK1\signed_CSC_Cetus_Europe_I8700XENJK1.csc Open Phone image at : C:\omnia7csc\signed_phone_Cetus_Europe.bin Open Eboot image at : C:\omnia7csc\signed_eboot_Cetus_Europe.eb0 Open PDA image at : C:\omnia7csc\signed_pda_Cetus_Europe.nb0 Open CSC image at : C:\omnia7csc\signed_CSC_Cetus_Europe_I8700TMNJK1.csc Detect COM16 Port [Channel 0] Confirm Model Name [Channel 0] FLASH UNLOCK [Channel 0] FLASH UNLOCK Success!!! [Channel 0] Send Partition Table [Channel 0] Partition Table is correct [Channel 0] Erase AMSS Region [Channel 0] Write AMSS Data ERROR[Channel 0] Write AMSS Data Fail!!! [Channel 0] FLASH LOCK Detect COM16 Port Open Phone image at : C:\omnia7\signed_phone_Cetus_Europe.bin Open Eboot image at : C:\omnia7\signed_eboot_Cetus_Europe.eb0 Open PDA image at : C:\omnia7\signed_pda_Cetus_Europe.nb0 Open CSC image at : C:\omnia7\signed_CSC_Cetus_Europe_I8700ORAJID.csc [Channel 0] Confirm Model Name [Channel 0] FLASH UNLOCK [Channel 0] FLASH UNLOCK Success!!! [Channel 0] Send Partition Table [Channel 0] Partition Table is correct [Channel 0] Erase AMSS Region [Channel 0] Write AMSS Data ERROR[Channel 0] Write AMSS Data Fail!!! [Channel 0] FLASH LOCK Detect COM16 Port Open Phone image at : C:\Users\Eto\Desktop\I8700 XEN I8700XENJK1\I8700 XEN I8700XENJK1\signed_phone_Cetus_Europe.bin Open Eboot image at : C:\Users\Eto\Desktop\I8700 XEN I8700XENJK1\I8700 XEN I8700XENJK1\signed_eboot_Cetus_Europe.eb0 Open PDA image at : C:\Users\Eto\Desktop\I8700 XEN I8700XENJK1\I8700 XEN I8700XENJK1\signed_pda_Cetus_Europe.nb0 Open CSC image at : C:\Users\Eto\Desktop\I8700 XEN I8700XENJK1\I8700 XEN I8700XENJK1\signed_CSC_Cetus_Europe_I8700XENJK1.csc [Channel 0] Confirm Model Name [Channel 0] FLASH UNLOCK [Channel 0] FLASH UNLOCK Success!!! [Channel 0] Send Partition Table [Channel 0] Partition Table is correct [Channel 0] Erase AMSS Region [Channel 0] Write AMSS Data ERROR[Channel 0] Write AMSS Data Fail!!! [Channel 0] FLASH LOCK Detect COM16 Port [Channel 0] Confirm Model Name [Channel 0] FLASH UNLOCK [Channel 0] FLASH UNLOCK Success!!! [Channel 0] Send Partition Table [Channel 0] Partition Table is correct [Channel 0] Erase AMSS Region [Channel 0] Write AMSS Data [Channel 0] AMSS Download Success!! [Channel 0] Erase DSP1 Region [Channel 0] Write DSP1 Data [Channel 0] DSP1 Download Success!! [Channel 0] Erase APPSBL Region [Channel 0] Write APPSBL Data ERROR[Channel 0] Write APPSBL Data Fail!!! [Channel 0] FLASH LOCK I think there's no Rom for this device....
Memory size doesn't matter on the ROM, they fit both 8 and 16GB. If i where you I would flash it with stock ROM and deliver it to a Samsung repair center. They should fix it for free.
ballajalla said: Memory size doesn't matter on the ROM, they fit both 8 and 16GB. If i where you I would flash it with stock ROM and deliver it to a Samsung repair center. They should fix it for free. Click to expand... Click to collapse This is why my friend came to me, he couldn't find the invoice ( actually it was a wedding gift) we still got the warrantycard but Sammy wants a proof of purchase... Anyway, the whole thing is weird ... some Roms flash and some don't- I guess it depends on the wp7 flasher version also... At one time the whole system booted like in updating mode ( PC--->Phone do not disconect) but it got stuck... Is there anyway to trace what's the version of this phone by IMEI? The box only says gt-i8700 and no branding at all... Yep, it seems I need to find the right combo in order for this to work : right eboot+right PDA+ right csc
I'm sorry, cant help you with the flashing. I would go to another service center, they should help you if you ask them. The model has only been on the market for a year, so it is most likely within warranty, and they can check that from the serial number, they don't need proof of purchase, if they say so they are just being dicks..
When I called up Samsung warranty they just told me to take it into a local centre. I rang the centre up and they said i just needed to drop it off with them...
Freypal said: When I called up Samsung warranty they just told me to take it into a local centre. I rang the centre up and they said i just needed to drop it off with them... Click to expand... Click to collapse I did call up the warranty center...they transferred me to the service center...I explained them that it was a wedding gift and it's more likely we're not gonna find the invoice- I mentioned the phone is a late 2010 model and it's covered under the 24 months EU warranty- but they said that without an invoice there's nothing they can do except repair it for money.
Update1 Samsung Austria is acting like dicks, they keep on asking about invoice/purchase proof in order to take it. They don't seem to care that, actually, there is no Omnia7 out-of-warranty yet ( due to the fact that it has a 24 months warranty and most of them were sold on early 2011). Man, they know it's a common failure and they keep repeating the same answer. Does anybody know how if there's a European Samsung customer service where I can ask about this issue?
I would contact Samsung on Facebook or Twitter, they seem to respond better there since it's out in the open.
any progress with this?? i have the exact same issues and cant get warranty repair.
[Q] Help Samsung Omnia 7 MIBIB Flash Error
Hello, I am getting every time a MIBIB Flash Error. I have a Samsung Omnia 7 where the software update failed and doesn´t start anymore. I just getting the boot logo from samsung, thats all. I can set it to the Download Mode by pressing Camera+Volume Up+Power but the by Flashing I am getting the mentioned error. (1)\signed_pda_cetus_europe.nb0 Open CSC image at : c:\users\***********\downloads\i8700dtmjj6(1)\signed_csc_cetus_europe_i8700dtmjj6.csc Open Phone image at : c:\users\***********\downloads\i8700dtmjj6(1)\signed_phone_cetus_europe.bin Open CSC image at : c:\users\***********\downloads\i8700dtmjj6(1)\signed_csc_cetus_europe_i8700dtmjj6.csc Open Eboot image at : c:\users\***********l\downloads\i8700dtmjj6(1)\signed_eboot_cetus_europe.eb0 Open PDA image at : c:\users\***********\downloads\i8700dtmjj6(1)\signed_pda_cetus_europe.nb0 Detect COM4 Port [Channel 0] Confirm Model Name [Channel 0] FLASH UNLOCK [Channel 0] FLASH UNLOCK Success!!! [Channel 0] Send Partition Table [Channel 0] Partition Table is correct [Channel 0] Erase MIBIB Region [Channel 0] Write MIBIB Data ERROR[Channel 0] Write MIBIB Data Fail!!! [Channel 0] FLASH LOCK I hope there is some one in the world wide web, who can help me. :crying:
I had the same problem as You - Flash lock. Nobody since 6m is able to help me. I only wasted my time.
Flash another modem?
Hi all, I'm trying to flash the modem from the Bell variant of the N900W8 on my N9005 but Odin reports failure and my phone says "Secure Check Fail : modem". I'm able to flash the existing modem without issue. Any ideas? Edit: hmm sounds like I should flash the NON-HLOS.bin file first? Edit 2: Flashing the NON-HLOS.bin file first didn't work either...
Installing TWRP on Galaxy S8 - Stuck at NAND Write Start!!
Everytime I click on start in odin while installing TWRP it stucks at NAND Write Start!!! Nothing happens afterwards. Help!!! Device - Galaxy S8 G950FD TWRP file selected - twrp3.1.1.0dreamlte.img.tar Below is screenshot attached.
enable oem unlock in developer section in settings