Related
Hello..
Have been using |Mdeejay FroYo Sense Matted v. 1.4 with 2.15 radio, and some 1 told me to change radio to 2.14 because of better battery,etc.... and i did.. and after that, when i try to turn on my wifi, it says Error... just that..
Help please..
Ive tried to delete android folder on my sd card, and then recopy it fresh, but again same problem..
Thanks
Laynee1 said:
Hello..
Have been using |Mdeejay FroYo Sense Matted v. 1.4 with 2.15 radio, and some 1 told me to change radio to 2.14 because of better battery,etc.... and i did.. and after that, when i try to turn on my wifi, it says Error... just that..
Help please..
Ive tried to delete android folder on my sd card, and then recopy it fresh, but again same problem..
Thanks
Click to expand...
Click to collapse
Hey, im using the same MDJ build, ive also tried radio 2.14 but get better battery life/ slower drain from 2.15, tho as you prob know radio performance depends on many factors, location being a big 1, wifi worked fine with both.
2 suggestions, update kernel to MDJ s7.1 or go back to radio 2.15
Thanks alot for fast and swift reply ..
I have downloaded s7.1 mdj kernel , but in instructions he says that i should put zimage and root folder into android folder, but nothing changes... Kernel stil stays 6.1... how to change kernel ffs ?
No probs,
with s7# kernels you need to copy zimage to your android folder but the modules have to be placed directly in the system/lib folder (using es or root explorer), not the same folder as the zimage.
not near my laptop right now so can't give you the exact path,
its all in MDJ's kernel thread tho just look 2 or 3 pages back from the last page ul see the instructions
p.s,
make sure you do a full reboot when done.
Before you go changing your kernel, try booting into Android with wifi on in Windows, then in Android turn wifi on, if it says error, just try to turn it on again.
If that doesn't work, try booting into Android with wifi in Windows turned off, then if it says error, try turning wifi on again.
The reason I say this, is because with one of the builds on my card, if I boot Android with wifi off in Windows, wifi will not work at all in Android, but if I boot Android with wifi on, it works but sometimes says error the first time, but if I simply turn wifi on again, then it turns right on and connects.
And I have read other people's comments that wifi would'nt work for them unless it was turned off in Windows.
So I say try it both ways, and give it 2 chances at turning wifi on each time.
If it works, good. If not, you can still change your kernel or try another build.
Hope this helps, and saves you some time and effort
This version is now discontinued. find the data2ext version or tmous version here
http://forum.xda-developers.com/showthread.php?p=10503046
RAFDROID HD 2.0 - NAND VERSION
Click to expand...
Click to collapse
--- FIRST OF ALL, PLEASE READ POST 2 FOR UPDATED FAQ. IF YOU HAVE QUESTIONS OR ISSUES, MOST PROBABLY YOU WILL FIND THE ANSWER THERE WITHOUT NEEDING TO POST A NEW MESSAGE ---
I'm not a dev. I'm just a curious user that want to learn, fail, search, retry, fail again and then succeed also thanks to people here that helped me with tips and knowledge sharing
This is a personal build made for my self, based on DESIRE HD.
Is 90% stock, % battery indicator and some animations/icons.
It's fully DEODEXED so you can theme it as you want.
I tried also to keep most of the apps, wallpapers and other stuff in it.
But most important it uses DATA.IMG on SDCARD so you dont have to worry about storage limite on LEO512
Please note: this, as happenend whe using Android from SD, could cause data corruption and causes a little lag during app installation. There is nothing I can do to solve those two issues. You are warned!
Credits and thanks:
-Cotulla and DFT for making all this possible
-darkstone for his big help
-mdeejay for initrd.gz (modified by me to support data.img) and kernel
-Kouno.Takaaki for his idea and init file
-Rajko
-crawling
-ocm
-Cass
-cedesmith
-domineus
-imilka for help me solving wifi issue
-all people on #htc-linux
and probably a lot of other people I'm forgetting
FEATURES:
- Deodexed and Zipaligned, not sqashfsed
- Latest kernel
- RMNET
- Multilanguage
- Rooted (SU app + permessi SU)
- AdFree
- 5mpx camera with face recognition + 800*400 camcorder
- HSDPA, GPS, Bluethoot, WiFi all working
- % battery icon and status bar icons changed (use original framework-res.apk to go back to stock attached in 2nd post)
- fonts changed (use original fonts to go back to stock attached in 2nd post)
- Working HTC-SENSE.COM (at least for me)
- data.img on SD support
WHAT'S WORKING
Everything except stock HTC Reader (removed)
CHANGELOG
Code:
2.0
New base Desire HD 1.72.405.3
RMNET
Rooted (su + Superuser APP)
Bootanimation changed
Bootsound changed (very very low, just a "beep")
Auto APN
AdsFree (updated)
New Advanced Power menu (credit to reef2009)
New initrd/data2sd system (credit to Takaaki.Takuno)
some minor tweaks & fixes
1.0 - Initial Release
Based on RUU 1.32.405.6
Removed HTC E-Reader
Removed SoundHound
Removed AmazonMP3
INSTRUCTIONS
- You need at least MAGLDLR 1.10
- Download the Data size package you want
- Unzip it and copy all the content to your SD root respecting the folder structure. Insert the SD in the HD2
IF YOU NOT DO THIS BEFORE, YOUR INSTALLATION WILL FAIL
IF YOU ARE ON A 1024 LEO YOU CAN AVOID THIS.
- Download the RAFDROID HD package
- Unzip it on your computer, enter in MAGDLR bootloader, choose USB flasher, connect your HD2 to your computer and use INSTALL.EXE
- Wait the rebooting. Keep always the SD inside.
- First install takes up to 5 min
- Enjoy
- As all HD build, initially this will be slugghis and lagging, specially if you select to restore your google settings. The build will become fast after some hours and a couple of reboots.
DOWNLOADS
Click to expand...
Click to collapse
WARNING 1) Data system changed between RafDroid HD1 and RafDroid HD2. Now you need a "config.txt" in the data2sd folder. I suggest to old 1.0 users to download the new packages here to be sure that all works.
WARNING 2) I assure compatibility only with 512 and 1024 data images. Using bigger images, specially more than 2gb, could cause issues (no boot, errors installing apps...)
WARNING 3) I suggest always to start with a fresh data.img. Anyway you can try too keep your old data.img but I cannot assure you that you will have no bugs. Important is to keep the "data2sd" folder with the config.txt inside.
DATA PACKAGE for RAFDROID HD 2.0 512MB -> http://www.multiupload.com/MA47VX8ALS
DATA PACKAGE for RAFDROID HD 2.0 1024MB -> http://www.multiupload.com/6BA2EZ49L0
RAFDROID HD 2.0 -> http://www.multiupload.com/CLK8LXQG0M
--------------------------------------------------------------------
DATA PACKAGE 512MB -> http://www.multiupload.com/F91OFAFDX7
DATA PACKAGE 1024MB -> http://www.multiupload.com/GWRDNTXALF
RAFDROID HD 1.0 -> http://www.multiupload.com/P2AWG7IRR7
If you need more space, you can replace the data.img with ones bigge but I NOT SUGGEST THIS. We have clues that data.img bigger than 2gb causes issues. So please, if you want to avoid bugs, stay with 1gb maximum that is plenty space for everything.
DONATE:
Click to expand...
Click to collapse
I dont think it's fair to ask for donations because all this was possible thanks to the people credited above.
Anyhow, because some one pm'ed me asking to donate, and becouse I spent a lot of time in this, if you want to buy me a coffee for all the time I spent, you can do this here DONATE
Anyway I would suggest to donate to Cotulla and DFT team and other devs.
BE ADVISED: THIS BUILD, CAUSE IT'S SIZE, WILL WORK ONLY WITH THIS METHOD OF DATA2SD. IT'S TOO BIG TO WORK WITHOUT IT. EXCEPT FOR 1024 LEO WHER IT *SHOULD*(MUST BE TESTED) WORK WITHOUT DATA.IMG
If you want DesireHD standard fonts, download this package and replace the entire /system/fonts content with the ones included, using droid explorer or adb, after first boot
http://www.multiupload.com/5EXLIPO3N4
If you want the stock look this is the stock framework-res.apk. i will not explain how to mess with it, google if you dont know. anyway be careful. messing with this file could cause loop reboots and you will have to reflash
RAFDROID HD 2.0 -> http://www.multiupload.com/EBTBFZV8F8
RAFDROID HD 1.0 -> http://www.multiupload.com/889C7U9B0T
FAQ - QUESTIONS and BUG FIXES
PLEASE READ
Click to expand...
Click to collapse
q) I'm having high battery drain
a) Try reboot. Try disabling gps in location. As you can see from the screenshot I have 4mA with WIFI active! Also be careful. If during google account setup you choose to backup/restore all your data, the sync process will be dramatic heavy because it has to reinstall all your apps. It could need a couple of hours to settle. Also high battery drain could be caused by SD. try another one.
q) It's really laggy!!!!
a) as all Desire HD builds this is BIG! This needs at least 10-15 minutes after boot to be usable. Then try to use it for 5-6 hours.. and do a couple of reboots.. you will see that the speed will improve. After 24 hours of use and 4-5 rebots this will be really fast.
q) I have no GPS or the fix is really slow
a) Firs fixt can take up to 5 minutes. just wait. If still not works, try to change the gps zone in the config.txt (read below)
q) I have low quadrant scores
a) yes, this is true. This is because data sync is enabled by default. You can try to disable it but this will give you more risks of data corruption.
q) Can I unmount the SD while in use or connect the phone as mass storage to my pc while in use
a) No. This will cause data corruption. Power down the pone and use an SD card reader to copy your files.
q) I have no SU permission!!!
a) Install z4root (google for it) and execute permaroot. Reboot.
q) It not boots
a) be sure that the ".config" file is in your SD on the root. and there is also the folder "data2sd" with "data.img" inside. If still no boot, try to reformat your SD card, copy the img again, and retry.
q) I have no data/3G/HSDPA
a) probably you have to set your apn manually. google it for tips on how to do and what settings are need for your carrier
q) How do I remove BOOTSOUND / How do I change bootanim
a) bootsound and bootanim are located in /system/etc/customer. Just delete android_audio.mp3 if you dont want sound
ABOUT THE CONFIG.TXT FILE
Click to expand...
Click to collapse
You can change some parameters directly in the config.txt before booting:
Code:
data_sd=0
- 0, default, use nand userdata, THIS WILL CAUSE NO BOOT for 512 LEO
- 1, enable external data.img support (/sdcard/data2sd/data.img)
data_size=512
- size of data.img, only work when data.img support enabled and first install if you dont have a data.img.. it will create for you. No need to specify it if you already have a data.img in the data2sd folder
data_sync=1
- 0, fast, default, disable sync option when mount data.img MAY CAUSE DATA CORRUPTION. I SUGGEST TO NOT USE THIS
- 1, safe, enable sync option when mount data.img, use this if experiencing data corruption
lcd_density=240
- size of icons
gps_zone=europe
- country string for better gps fix. you can find your country code here [URL="http://www.pool.ntp.org/zone/@"]http://www.pool.ntp.org/zone/@[/URL]
Having the DATA PACKAGE 1024MB now Waiting For the RAFDROID HD 1.0 now
Hey man, you're really rock Wonderful Rom, everything is work fine on my HD2 ! Now I'm having 2GB data.img on my sd card it works man, you are right now i got no worry about storage limite on LEO512
Thank you so much !!
Good to hear you fixed all those bugs, hope it's quick!
Nice, but could you also provide us with stock framework (so it can be 100% stock lol)?
and can we use Kouno's method of modifying /system with "update" folder on sdcard?
Thank you very much. I need it so
mmmm.. i wanna try this build.. mmmm
nice raf
oh.. why mdj kernel?
Krendelrus said:
Nice, but could you also provide us with stock framework (so it can be 100% stock lol)?
and can we use Kouno's method of modifying /system with "update" folder on sdcard?
Click to expand...
Click to collapse
not at the moment
I will check to update this in the next release
Wooooow
Fantastic HD2 scene!
Thanks Raf
PS: I would like too, in future a stock framework.
if you can provide some SCREENSHOTS also.i am looking forward to this,specially extra memory part is cool.
rafpigna said:
not at the moment
I will check to update this in the next release
Click to expand...
Click to collapse
thanks for replying
why you're not using latest Ace RUU (RUU_Ace_HTC_WWE_1.72.405.3)?
you can get it here http://forum.xda-developers.com/showthread.php?t=879375
isnt it better to have PPP rather than RMNET because RMNET is slower.
having said that, has there been a fix for PPP because im lossing network bar frequently.
BTW thanks for the build, will be testing it out soon
When is this boiled going to be out? I wanna try out this build as I can't seems to install much of applications on any otherbrom asnitbonly gives me less then 100mb. And nownthe current remaining soqcenisnlessnthen ten mb. Can't waitbto try out a new and a better rom. How aboutbthe cam coder is the quality better?
Krendelrus said:
thanks for replying
why you're not using latest Ace RUU (RUU_Ace_HTC_WWE_1.72.405.3)?
you can get it here http://forum.xda-developers.com/showthread.php?t=879375
Click to expand...
Click to collapse
guys, because initially I made this for myself.
Now that is released I will try to update it in the nexts
rafpigna said:
guys, because initially I made this for myself.
Now that is released I will try to update it in the nexts
Click to expand...
Click to collapse
ok, got it
rafpigna said:
guys, because initially I made this for myself.
Now that is released I will try to update it in the nexts
Click to expand...
Click to collapse
Good work Raf, been waiting for this. I've downloaded the data package and was wondering if it will be possible to use my old data.img file from another SD HD build and possibly use a 2GB data.img file too?
daysey said:
Good work Raf, been waiting for this. I've downloaded the data package and was wondering if it will be possible to use my old data.img file from another SD HD build and possibly use a 2GB data.img file too?
Click to expand...
Click to collapse
Dont know.. maybe there will be bugs, but try it.. if this not work or you have bugs, delete all things from SD, reflash NAND, and start again
about 2gb data, yes, you can. just replace the file. I will upload 2GB and 4GB for convenience, later as soon I have time
This build will be awesome when it runs correctly... Is it right, it uses for data the data.img on the sd card, when you release a new uodate we can safe our data and can make a update without loosing my apps ? This will be great news ?!
so will all my texts get saved to the sd card?
as on other NAND builds my phone can barely operate after a couple days use due to insufficient storage.
also, what determines whether I should get the 512MB or 1024MB data package?
manish2039 said:
isnt it better to have PPP rather than RMNET because RMNET is slower.
having said that, has there been a fix for PPP because im lossing network bar frequently.
BTW thanks for the build, will be testing it out soon
Click to expand...
Click to collapse
Not true,atleast not for me. (the build i use in my sig)
Sinds NAND rmnet is as fast for me as ppp,same up and download speed.
In the time with sd card builds ppp was faster for me,now not (for me)
Just test it with speedtest.net app in the market for free
Hey all,
I'm usually pretty good at figuring these types of things out, but unfortunately I haven't been able to figure this one out yet.
Wifi works fine in WinMo 6.5 and WinPhone 7. I haven't tried SD version of Android, but I'd rather not go that route as I want to be able to use a fully functioning NAND version of Android.
I have done Task29/wipe data/cache/dalvik cache on many occasions, repartitioned, reinstalled WinMo 6.5 and then started over with MAGLDR (latest version), replaced wifi module libraries, but nothing has proven to work. Everything else is perfect, though.
Somebody has to have experienced this before? I couldn't find much in terms of a solution by searching.
Thanks!
What HD2 Radio version are you using?
What Android ROM are you using?
Have you made sure that it is a MAGLDR version you are trying to install, not the cLK version?
Why would you need to replace the WiFi module librarys as your ROM should work without error after installation?
A bit more info and we should be able to sort this one out!
custommsp said:
Hey all,
I'm usually pretty good at figuring these types of things out, but unfortunately I haven't been able to figure this one out yet.
Wifi works fine in WinMo 6.5 and WinPhone 7. I haven't tried SD version of Android, but I'd rather not go that route as I want to be able to use a fully functioning NAND version of Android.
I have done Task29/wipe data/cache/dalvik cache on many occasions, repartitioned, reinstalled WinMo 6.5 and then started over with MAGLDR (latest version), replaced wifi module libraries, but nothing has proven to work. Everything else is perfect, though.
Somebody has to have experienced this before? I couldn't find much in terms of a solution by searching.
Thanks!
Click to expand...
Click to collapse
Hey. Thanks for joining!
- Radio 2.15.50.14 and one of the older ones which was installed when I picked up this phone
- Roms:
NDT MIUI Froyo V6.2 currently.
Tried [CWR] BOYPPC-SHIFTPDA_GINGER 2.3.4-Sense.s V29 (12.Jun), CMYLXGO's Stock Desire HD(2) NAND ROM v1.1.17 and a few others i can't remember. All MAG versions.
I tried replacing the libs, because i've read that as part of a fix for related wifi problems from earlier this year.
Thanks!
custommsp said:
Hey. Thanks for joining!
- Radio 2.15.50.14 and one of the older ones which was installed when I picked up this phone
- Roms:
NDT MIUI Froyo V6.2 currently.
Tried [CWR] BOYPPC-SHIFTPDA_GINGER 2.3.4-Sense.s V29 (12.Jun), CMYLXGO's Stock Desire HD(2) NAND ROM v1.1.17 and a few others i can't remember. All MAG versions.
I tried replacing the libs, because i've read that as part of a fix for related wifi problems from earlier this year.
Thanks!
Click to expand...
Click to collapse
You have the most common Radio 2.15.50.14 so that isn't the problem.
The fix is mainly for cLK versions so it could use the PPP interface but if you are using MAGLDR then that isn't needed - this alone could be your problem, I reccomend not installing this patch any more?!
I play with roms a lot and normally my errors are due to using a kernel which the rom wasn't developed for - or more recently, frequent drops to the internet.
When my drops happened, I had done nothing different but it seems that a change in CM7 source now addressed my routers security settings differently - I have no idea when it was added and I was lucky enough to find a firmware update for my router which solved the problem.
Out of interest, when you click on wifi, does it say error or does it try to connect and randomly drop? Error would indicate a kernel/radio/hardware problem and dropping or not connecting would possibly indicate router problem.
Possibly, one of the best places to start is the security settings of your router, disable all security and see if it will connect... if it does then apply security - I use WPA2 PSK TKIP and it now works for me!
NDT MIUI Froyo V6.2 & CMYLXGO's Stock Desire HD are quite old (In terms of development), BOYPPC-SHIFTPDA_GINGER 2.3.4-Sense.s V29 is new and updated frequently so i'm unsure why all would have the same problem?!?!.
You could also try my rom located in my signature "HardDroid2" as I have extensively tested this and have no problems (Not trying to punt my rom at all!).
If changing your router settings or no other roms work then it is beyond me as there are only a few combinations af possible hardware/software faults!
Hope this helps
Already installed Is the phone supposed to boot in Airplane mode enabled for the first boot?
Ok, unfortunately the same issue with WiFi. What happens when i turn wifi on is it takes about 15 seconds for the check to appear in the box, then it stays on for about 15 more seconds with no networks showing, then it turns off automatically. The same thing with every rom I've tried, unless I start messing with libs or conf files at which point I get "error" or it doesn't turn on at all.
Thanks!
custommsp said:
Already installed Is the phone supposed to boot in Airplane mode enabled for the first boot?
Thanks!
Click to expand...
Click to collapse
Ummmm... NOPE!
I think your problem is with your radio rom. I would reccomend starting from scratch!
This is what I do and it works fine for me:
Prep SD Card: Format FAT32 and also create a 1GB Ext3 Partition (For apps2SD if needed)
Copy the rom update.zip to FAT32 partition of SD Card & Insert into phone.
Run HSPL3_PKG.exe and install HSPL 2.08
Flash Radio_Leo_2.15.50.14
Run Task 29 - wipe phone
Install MAGLDR 1.1.3
start device (Hold down power button until menu list appears) choose USB Flasher
Install Recovery 150MB System/5MB Cache (ClockworkMod Recovery v4.0.0.0)
Start MAGLDR (Hold down power button until menu list appears) Select "AD Recovery"
Boot ClockworkMod and install update.zip from SD Card.
I'm not trying to teach you how to suck eggs... but maybe there is a little step you may of missed?!?!?
deano309 said:
Ummmm... NOPE!
I think your problem is with your radio rom. I would reccomend starting from scratch!
This is what I do and it works fine for me:
Prep SD Card: Format FAT32 and also create a 1GB Ext3 Partition (For apps2SD if needed)
Copy the rom update.zip to FAT32 partition of SD Card & Insert into phone.
Run HSPL3_PKG.exe and install HSPL 2.08
Flash Radio_Leo_2.15.50.14
Run Task 29 - wipe phone
Install MAGLDR 1.1.3
start device (Hold down power button until menu list appears) choose USB Flasher
Install Recovery 150MB System/5MB Cache (ClockworkMod Recovery v4.0.0.0)
Start MAGLDR (Hold down power button until menu list appears) Select "AD Recovery"
Boot ClockworkMod and install update.zip from SD Card.
I'm not trying to teach you how to suck eggs... but maybe there is a little step you may of missed?!?!?
Click to expand...
Click to collapse
Much appreciated, I'll give this a try.
custommsp said:
Much appreciated, I'll give this a try.
Click to expand...
Click to collapse
I would reccomend re-downloading the files, especially the radio rom as I have a feeling it may be corrupted - don't know why it would work on WP7 though??
Use the HSPL3_PKG.exe to install HSLP 2.08 as it is regarded as the best.
I use Loader 2.10 KSubedi (MAGLDR 1.1.3 Debranded) just for asthetic reasons.
We will get there!!! lol
Same deal, unfortunately. I've noticed that the mac address is "unavailable" at all times, including the 10 secs the wifi is actually on (according to the switch)
custommsp said:
Same deal, unfortunately. I've noticed that the mac address is "unavailable" at all times, including the 10 secs the wifi is actually on (according to the switch)
Click to expand...
Click to collapse
Did you re-download the radio from here?: http://www.multiupload.com/QP0IWGY42F
I don't understand why your wifi works under wm6.5 (which installs during flashing rom) & WP7 (which runs the same way as android nand) but not under android... I would of classed it as a corrupted file and im completely at a loss!!!!
It can't be a hardware fault and there isn't any differences in earlier/later versions of the HD2's wifi module!!!
OK, I admit it.... I'm stumped!
deano309 said:
Did you re-download the radio from here?: http://www.multiupload.com/QP0IWGY42F
I don't understand why your wifi works under wm6.5 (which installs during flashing rom) & WP7 (which runs the same way as android nand) but not under android... I would of classed it as a corrupted file and im completely at a loss!!!!
It can't be a hardware fault and there isn't any differences in earlier/later versions of the HD2's wifi module!!!
OK, I admit it.... I'm stumped!
Click to expand...
Click to collapse
Yep, that file. Maybe I need to install the latest Tmobile 6.5 rom and start from that?
custommsp said:
Yep, that file. Maybe I need to install the latest Tmobile 6.5 rom and start from that?
Click to expand...
Click to collapse
If you install the latest rom and then task 29, you still have the radio version which installed with the rom as task 29 doesn't touch that section!
I remember a couple of years ago when I changed the wifi module on a PSP that it no longer held a mac address when using original Sony firmware... has your device been in for repair?
Just a thought really, i'm grabbing at straws since it really doesn't make sense to me!
deano309 said:
If you install the latest rom and then task 29, you still have the radio version which installed with the rom as task 29 doesn't touch that section!
I remember a couple of years ago when I changed the wifi module on a PSP that it no longer held a mac address when using original Sony firmware... has your device been in for repair?
Just a thought really, i'm grabbing at straws since it really doesn't make sense to me!
Click to expand...
Click to collapse
I'm not sure about its history as I bought it used. Tomorrow is another day with more opportunities to resolve this issue.
Nothing changed by me installing a stock T-mobile WinMo 6.5 then going through the process of converting to NAND android. I found out that I'm not able to save a manual Wi-Fi network entry. Maybe this is a clue for the problem?
Thanks!
custommsp said:
Nothing changed by me installing a stock T-mobile WinMo 6.5 then going through the process of converting to NAND android. I found out that I'm not able to save a manual Wi-Fi network entry. Maybe this is a clue for the problem?
Thanks!
Click to expand...
Click to collapse
Well looking into the kernel, it seems that it will create a custom MAC address for each device to get past the 00:11:22:33:44:55 issue (I don't know what variables it would use to create this but possibly imei???)
There are no really adjustable settings in wpa_supplicant.conf which would help (As far as I can see)
Since you aren't showing a MAC address, it would indicate a problem with your hardware (as no other device has this problem) But why Windows roms would still work is beyond me and the only change in hardware revisions over the life of the HD2 has been to the lcd screen and not the radio hardware.
I have searched and tried to find more information on this but i'm unable to find a conclusive answer or solution
Here is a thought: Download the files which I use from here: http://www.andbuddy.com/files/FOBBu1308083933.html
This contains all the files which I use and a small guide - Please follow ALL the steps as this has given me a 100% working device!
If it still doesn't work after this then I will have to admit that i'm beaten
deano309 said:
Well looking into the kernel, it seems that it will create a custom MAC address for each device to get past the 00:11:22:33:44:55 issue (I don't know what variables it would use to create this but possibly imei???)
There are no really adjustable settings in wpa_supplicant.conf which would help (As far as I can see)
Since you aren't showing a MAC address, it would indicate a problem with your hardware (as no other device has this problem) But why Windows roms would still work is beyond me and the only change in hardware revisions over the life of the HD2 has been to the lcd screen and not the radio hardware.
I have searched and tried to find more information on this but i'm unable to find a conclusive answer or solution
Here is a thought: Download the files which I use from here: http://www.andbuddy.com/files/FOBBu1308083933.html
This contains all the files which I use and a small guide - Please follow ALL the steps as this has given me a 100% working device!
If it still doesn't work after this then I will have to admit that i'm beaten
Click to expand...
Click to collapse
Before doing all of this I have decided to try a SD version of Android. It's producing the same result!
I'm have the same problem . please help us
spellcaster said:
I'm have the same problem . please help us
Click to expand...
Click to collapse
I'm suspecting that the actual wifi related hardware is damaged somewhere, maybe the coaxial cable, at least in my phone.
Do you try solution : http://forum.xda-developers.com/showthread.php?t=827521
i try but i can't do step 6 :
"6. Go to menu Device -> File Explorer. New window will come up."
it not show file
- I Think problem relate with hardware because with the same Room , same Radio , same Wif network other device ok but of me false
- If you have new information or new SOLUTION please send email for me [email protected]
Thanks
Anyone has problem with 3g and CM10?
like its working, but after a long time, 3g icon still on bar but not efectuve working, browser cant research for a conection
after a disable data conection and reenable it everything start work again.
skulljoi said:
Anyone has problem with 3g and CM10?
like its working, but after a long time, 3g icon still on bar but not efectuve working, browser cant research for a conection
after a disable data conection and reenable it everything start work again.
Click to expand...
Click to collapse
Enable Data roaming and national data roaming on Settings -> Wireless & Networks -> More... -> Mobile networks
Worked for me
Caesarivs said:
Enable Data roaming and national data roaming on Settings -> Wireless & Networks -> More... -> Mobile networks
Worked for me
Click to expand...
Click to collapse
Worked for me (2)
Caesarivs said:
Enable Data roaming and national data roaming on Settings -> Wireless & Networks -> More... -> Mobile networks
Worked for me
Click to expand...
Click to collapse
i has enabled data romaing but national data roaming off, will try with this option enabled now, tks
did you know how the CM10 work with auto enable/disable sync and 3g connection?
on preview version i has an option, turn of sync and 3g after a X mim with no incomming news or something like that
Caesarivs said:
Enable Data roaming and national data roaming on Settings -> Wireless & Networks -> More... -> Mobile networks
Worked for me
Click to expand...
Click to collapse
I try check the 2 options, but something happend, after i wake up, the icon of internet still there, but no connection, after stop and start data conection, icon get out and get in and then everything start work normal
so you have other sugestion?
skulljoi said:
I try check the 2 options, but something happend, after i wake up, the icon of internet still there, but no connection, after stop and start data conection, icon get out and get in and then everything start work normal
so you have other sugestion?
Click to expand...
Click to collapse
Same problem here. I had no problems with 2.3.6 uk official. On CM9 and CM10 I have thuis issue.
Will try to do a clean install, (flash uk 2.3.6, then CM10) because my problems started with CM9.
Do you had this problem in CM9 too?
eduwp90 said:
Same problem here. I had no problems with 2.3.6 uk official. On CM9 and CM10 I have thuis issue.
Will try to do a clean install, (flash uk 2.3.6, then CM10) because my problems started with CM9.
Do you had this problem in CM9 too?
Click to expand...
Click to collapse
i was on 2.3.6 BR and the update to CM10, and the problem began
i am getting other issues like, cant merge PROFILE with my google account and some slowly process
Have you tried this solution http://forum.xda-developers.com/showthread.php?t=1623385&page=71
Thanks alot for your hard job, this ROM is AMAZING!
I have signal drop after install this ROM (using version 2012/7/21).
To solve my problem, I copied the File_GSM and File_Seem_Flex_Tables files from my stock ROM (Retail Brazil) and replace the CM9 files.
I put the files in /system/etc/motorola/bp_nvm_default and reboot, and now I have strong signal and no more drop calls.
The ROM CM9 to Motorola Bravo CrystalTalk function is supported. I tried to copy the file Phone.apk this ROM for the Milestone 2 and the option to configure the CrystalTalk appears in the phone settings, but after a reboot the settings are lost.
ATTACHED FILES
bp_nvm_default.zip - [Click for QR Code] (1.2 KB, 29 views)
Click to expand...
Click to collapse
I've tried this procedure in CM10 and it works!!
cruizgaray said:
Have you tried this solution http://forum.xda-developers.com/showthread.php?t=1623385&page=71
I've tried this procedure in CM10 and it works!!
Click to expand...
Click to collapse
Sorry but I tried this and the problems still there. I used the files attached and the files from a gb backup. I reflashed uk gb and then cm10. Everything works great but after an idle period the mobile data connection doesn't work. Any ideas¿¿
Sent from my A953 using xda app-developers app
Maybe you can try MotoAndroidDepacker
Use SBF that gives you - a good data conection
extract radio files recompile to SBF and - flash it
How To http://forum.xda-developers.com/showthread.php?t=1459470
mike_oldfield said:
Maybe you can try MotoAndroidDepacker
Use SBF that gives you - a good data conection
extract radio files recompile to SBF and - flash it
How To http://forum.xda-developers.com/showthread.php?t=1459470
Click to expand...
Click to collapse
Ok I will try this. I've extracted the files from a gb nandroid backup so I think that this is almost the same but I will give it a try.
I've also used the baseband switching app with no luck.
Anyone knows witch files manage the 3g on our phones¿ I replaced the ones that are listed in the above posts but are there others?
Thank you mates
Sent from my A953 using xda app-developers app
Hi,
I got the same problem for Wifi and in minor way for 3G with mine (my baseband is EPU93_U_00.60.00).
I deactivated the national roaming but reactivated it now for testing ...
For the Wifi I tried to disable 802.11n in the tiwlan.ini file but seems to not work.
I'll try to do the requested log readings from tezet when I would have time.
A message for lotan_rm, you're not the alone one (also need to reach 10 post for posting in dev )
eduwp90 said:
Sorry but I tried this and the problems still there. I used the files attached and the files from a gb backup. I reflashed uk gb and then cm10. Everything works great but after an idle period the mobile data connection doesn't work. Any ideas¿¿
Sent from my A953 using xda app-developers app
Click to expand...
Click to collapse
maybe you should change the files permissions. try -rw-r--r-- on both files and reboot.
lucasdeeiroz said:
maybe you should change the files permissions. try -rw-r--r-- on both files and reboot.
Click to expand...
Click to collapse
the files already have that propieties but thanks by the way.
I've also compiled a sbf with motoandroid depacker containing only the baseband files and the problem still there.
This problem is driving me crazy. Any ideas??
eduwp90 said:
the files already have that propieties but thanks by the way.
I've also compiled a sbf with motoandroid depacker containing only the baseband files and the problem still there.
This problem is driving me crazy. Any ideas??
Click to expand...
Click to collapse
what country you are?
which SBF (stock froyo) that gives you a good data conection? (full name)
eduwp90 said:
the files already have that propieties but thanks by the way.
I've also compiled a sbf with motoandroid depacker containing only the baseband files and the problem still there.
This problem is driving me crazy. Any ideas??
Click to expand...
Click to collapse
So you didn't replaced the original files. The attached files are with differents permissions. Use root explorer to replace the files and it will be with wrong permissions. Then, you change the permissions and reboot. At least here the permissions were wrong...
lucasdeeiroz said:
So you didn't replaced the original files. The attached files are with differents permissions. Use root explorer to replace the files and it will be with wrong permissions. Then, you change the permissions and reboot. At least here the permissions were wrong...
Click to expand...
Click to collapse
I'm from spain. The sbf that worked well for me was the uk gingerbread (MILS2_U6_4.1-22_SIGNED_UCAMILESTONE2B1B80E1014.0R_USXMILE2GBRTDACH_P013_A007_HWp2a_Service1FF.sbf).
I didn't replace that files because these are for brasil baseband. I replaced those files with ones on my backup that worked well. The problem persists.
So then I created a sbf using motoandroid depacker that only containts the cg45.smg (baseband files). Flashed it. Problem persists.
Checked the files permissions they are ok.
Used baseband changing app. Sadly, problem persisits.
I tried also a clean install. (flash uk gb, then install cm10 doing all the wipes etc...)
I will try to use brazil files and check the permissions..... thak you everybody
eduwp90 said:
I'm from spain. The sbf that worked well for me was the uk gingerbread (MILS2_U6_4.1-22_SIGNED_UCAMILESTONE2B1B80E1014.0R_USXMILE2GBRTDACH_P013_A007_HWp2a_Service1FF.sbf).
I didn't replace that files because these are for brasil baseband. I replaced those files with ones on my backup that worked well. The problem persists.
So then I created a sbf using motoandroid depacker that only containts the cg45.smg (baseband files). Flashed it. Problem persists.
Checked the files permissions they are ok.
Used baseband changing app. Sadly, problem persisits.
I tried also a clean install. (flash uk gb, then install cm10 doing all the wipes etc...)
I will try to use brazil files and check the permissions..... thak you everybody
Click to expand...
Click to collapse
So you have a big problem... Anyway, the files only let the mobile data working for more time, but don't "forever"... Now this problem appears after some hours.
So this problem is not solved at all?
Sent from my A953 using xda app-developers app
eduwp90 said:
So this problem is not solved at all?
Click to expand...
Click to collapse
Before overwriting files my connection was break after few minutes
After overwriting files data connection was extended to few hours
I could not get a continuous data conection in custom ROM
Hi all, here I wish to continue porting OmniROM from the P4/P4wifi over to our device the P5/P5wifi.
*Please note that this is simply a port of an already built rom. It was not built from source therefore anything that you may find to be broken will more than likely remain broken until it is fixed in the parent ROM.
-Many thanks to the builder of this rom @AAccount. His hard work made this ROM possible. :good:
-Thanks to @jolinnard whose kernel is being used in these ROMs. :good:
*On first boot the keyboard will not be showing. The fix is simple. Go to settings>Language & Input. Tap on Current Keyboard and flip the toggle next to Hardware. The keyboard should now be fine.
Working:
Everything works on the P5 AFAIK
Not working:
SELinux---------Need a recovery that supports it.
To those looking forward to a P5 3G rom then please note that there will not be one any time soon. AAccount has stopped building for the p4 3g so that means we don't have a 3g rom to port anymore. So unless AAccount starts porting for the p4 again there won't be a P5 rom.
Flash Instructions
Wipe data, system, cache, dalvik if coming from another ROM. If ugrading to a newer build then a simple Dalvik and cache wipe will do
Flash the ROM zip
Flash GAPPs (Thanks to @jolinnard)
Flash SuperSU
Reboot and enjoy
Original ROM thread
Credits
@AAccount - for the ROM
@jolinnard - For the kernel
@decatf - for his work on the p4 kernel which is used here that delivers great performance
If you helped out and I missed you in the credits then send me a PM and you will be credited
This port has been discontinued!!
"See why
Hey! Maybe some day I will back to Omni. I'm planning to erase my Gtab of Google stuff and enjoy a clean Android experience.
jolinnard said:
Hey! Maybe some day I will back to Omni. I'm planning to erase my Gtab of Google stuff and enjoy a clean Android experience.
Click to expand...
Click to collapse
@L3Ron ,i will give it a try.
@jolinnard
If you want to port or start with omni source? Nice to See your work for our Tab 8.9.
jolinnard said:
Hey! Maybe some day I will back to Omni. I'm planning to erase my Gtab of Google stuff and enjoy a clean Android experience.
Click to expand...
Click to collapse
Awesome!! Erased my internal sdcard by accident last week. Luckily I have the same files on my Nexus 9 so I was saved. This port works great for me. Should I even port for the P5? AAccount stopped building for the p4 as of May 23. Reason being that 3G doesn't work but oddly enough it does work on the P5 using our modified KK kernel and your data_on script.
bierma32 said:
@L3R0N ,i will give it a try.
Click to expand...
Click to collapse
Great. Tell me how it works for you.
L3R0N said:
Great. Tell me how it works for you.
Click to expand...
Click to collapse
Installed the Rom with out problems, i done a clean install and wipe / Format system / data / cache and dalvik.
I looks smooth and battery are good, it goes into deepsleep without battery consum.
Onliest Problem is i can not connet with wifi to a network. I can See all avaible network ,but no connection.
bierma32 said:
Installed the Rom with out problems, i done a clean install and wipe / Format system / data / cache and dalvik.
I looks smooth and battery are good, it goes into deepsleep without battery consum.
Onliest Problem is i can not connet with wifi to a network. I can See all avaible network ,but no connection.
Click to expand...
Click to collapse
Did you try with advanced wifi configuration? Try not use dhcp to assign wifi. Use a fixed ip. I had the same issue and that was the solution.
?
Enviado desde mi LG-D855
julen163 said:
Did you try with advanced wifi configuration? Try not use dhcp to assign wifi. Use a fixed ip. I had the same issue and that was the solution.
?
Enviado desde mi LG-D855
Click to expand...
Click to collapse
I tried different setting at the advanced configuration of WLAN settings with out success.
bierma32 said:
I tried different setting at the advanced configuration of WLAN settings with out success.
Click to expand...
Click to collapse
I have no such problems. My WiFi connects just fine. Try turning airplane mode on for a moment then turn it back off and try connecting again. Could it be the kernel? I'll p.m you a kernel to try and see if it fixes anything later on. Any logs?
OP has been updated with links to the new build released by AAccount today. According to him there were no major changes, just the usual Omni sync.
thanks for the unexpected gift! unfortunately i have problems with the zip package, it can't be opened/flashed, redownloaded 4-5 times from pc and tablet, same, checked the MD5 and it matches...am i the only one having troubles with it?
chemicalbuz said:
thanks for the unexpected gift! unfortunately i have problems with the zip package, it can't be opened/flashed, redownloaded 4-5 times from pc and tablet, same, checked the MD5 and it matches...am i the only one having troubles with it?
Click to expand...
Click to collapse
Nope same overhere.
Made a backup but transferred it to pc so I've got a problem! TWRP and no flashable zip on the internal sd...
Edit: used the sideload option with ADB and used the omni-5.1.1-20150706-p5wifi-HOMEMADE ROM
Got also problems with the WiFi connection. My network uses 192.168.2.xx range
chemicalbuz said:
thanks for the unexpected gift! unfortunately i have problems with the zip package, it can't be opened/flashed, redownloaded 4-5 times from pc and tablet, same, checked the MD5 and it matches...am i the only one having troubles with it?
Click to expand...
Click to collapse
No you are not the only one. This was reported to me earlier today by another user. I'm in the process of uploading a new zip to androidfilehost and another to mega. They will be up soon.
Nonomen said:
Nope same overhere.
Made a backup but transferred it to pc so I've got a problem! TWRP and no flashable zip on the internal sd...
Click to expand...
Click to collapse
I'm sorry to hear that. You can use adb to push a zip file to your sdcard for installation.
Use this command
Code:
adb push romname.zip sdcard
Or you could use sideload to install one as well. in twrp go to advanced then select adb sideload and connect your tab to your pc. Open up windows command prompt and type
Code:
adb sideload romname.zip
This should get a rom installed to your tab.
File has been re-uploaded. It opens fine now and should work fine.
L3R0N said:
File has been re-uploaded. It opens fine now and should work fine.
Click to expand...
Click to collapse
tnx for the quick answer. I've been able to sideload your first rom but it has lot of fc when installing or updating the apps from the playstore. Setting cpu to 1.2 had no result.
I will try your new uploaded file tomorrow.
Nonomen said:
tnx for the quick answer. I've been able to sideload your first rom but it has lot of fc when installing or updating the apps from the playstore. Setting cpu to 1.2 had no result.
I will try your new uploaded file tomorrow.
Click to expand...
Click to collapse
I have absolutely no problems with the ROM. No force closes or anything. Can you try a clean install of the 0716 build and see if it fixes anything?
Just before your re-upload I installed aosp-5.1.1-p5wifi-20150513. (Jollinnard). This ROM runs better than the UltraPlus I had before.
What are the advantages of your ROM over Jollinard's?
Nonomen said:
Just before your re-upload I installed aosp-5.1.1-p5wifi-20150513. (Jollinnard). This ROM runs better than the UltraPlus I had before.
What are the advantages of your ROM over Jollinard's?
Click to expand...
Click to collapse
There aren't any huge differences but here are a few notable changes
1) Ability to change battery icon
2) Battery color changes based on charge level
3) Pre rooted
4) Performance settings app included
5) Omniswitch recent
And a few others nothing big. IMO I prefer the browser in the omnirom over the aosp browser and the omni keyboard over the Google keyboard in the aosp ROM. But that's personal preference. Try both and pick a side *twix ad*
how i can use this rom for the p5 ?
thanks
4rch0 said:
how i can use this rom for the p5 ?
thanks
Click to expand...
Click to collapse
Edit the updater script and at the top where you see p5wifi simply delete the "WiFi" part so only p5 remains. Save the file put it back into the ROM zip and flash. Or you could simply flash the p5wifi recovery and you'll no longer have to worry about editing the script.
For future ROMs I think I'll remove the assert lines in the updater script so nobody else will have to worry about them.