Hello..
Have been using |Mdeejay FroYo Sense Matted v. 1.4 with 2.15 radio, and some 1 told me to change radio to 2.14 because of better battery,etc.... and i did.. and after that, when i try to turn on my wifi, it says Error... just that..
Help please..
Ive tried to delete android folder on my sd card, and then recopy it fresh, but again same problem..
Thanks
Laynee1 said:
Hello..
Have been using |Mdeejay FroYo Sense Matted v. 1.4 with 2.15 radio, and some 1 told me to change radio to 2.14 because of better battery,etc.... and i did.. and after that, when i try to turn on my wifi, it says Error... just that..
Help please..
Ive tried to delete android folder on my sd card, and then recopy it fresh, but again same problem..
Thanks
Click to expand...
Click to collapse
Hey, im using the same MDJ build, ive also tried radio 2.14 but get better battery life/ slower drain from 2.15, tho as you prob know radio performance depends on many factors, location being a big 1, wifi worked fine with both.
2 suggestions, update kernel to MDJ s7.1 or go back to radio 2.15
Thanks alot for fast and swift reply ..
I have downloaded s7.1 mdj kernel , but in instructions he says that i should put zimage and root folder into android folder, but nothing changes... Kernel stil stays 6.1... how to change kernel ffs ?
No probs,
with s7# kernels you need to copy zimage to your android folder but the modules have to be placed directly in the system/lib folder (using es or root explorer), not the same folder as the zimage.
not near my laptop right now so can't give you the exact path,
its all in MDJ's kernel thread tho just look 2 or 3 pages back from the last page ul see the instructions
p.s,
make sure you do a full reboot when done.
Before you go changing your kernel, try booting into Android with wifi on in Windows, then in Android turn wifi on, if it says error, just try to turn it on again.
If that doesn't work, try booting into Android with wifi in Windows turned off, then if it says error, try turning wifi on again.
The reason I say this, is because with one of the builds on my card, if I boot Android with wifi off in Windows, wifi will not work at all in Android, but if I boot Android with wifi on, it works but sometimes says error the first time, but if I simply turn wifi on again, then it turns right on and connects.
And I have read other people's comments that wifi would'nt work for them unless it was turned off in Windows.
So I say try it both ways, and give it 2 chances at turning wifi on each time.
If it works, good. If not, you can still change your kernel or try another build.
Hope this helps, and saves you some time and effort
Related
First thing, If you smoke, go grab your smokes, if you drink coffee, go grab a cup. This is usually a painless process but not always.
You will need HSPL installed, as well as a Class 4 or better sd card.
Before i begin i want to thank the following; with out them it would not be possible.
cr2
NetRipper
dcordes
Markinus
LeTama
Cotulla
dan1j3l
tsamolotoff on s200
Parad0XUA
Cass
http://forum.xda-developers.com/showthread.php?t=719646
THANKS GUYS!!
What you will need is the installation copy of the build that you will be using, the latest zImage and your sdcard.
The latest Android build can be found here: Its under the standard builds section.
http://gamesquare.co.uk/
And the latest Zimage can be found here:
http://cotulla.pp.ru/leo/Android/
I personally recommend the dan1j3l's Froyo build.
Down load both the zimage and the build.
Format your sdcard, select default settings and unselect the quick format option.
After the formatting is done (about 20 mins)
extract the contents of the Froyo build to your sdcard.
Located in the folder "android" you will find a file names zimage, replace it with the one you downloaded.
WITH YOUR USB PLUGGED INTO A POWER SOURCE, reboot your phone.
As soon as you can, using the built in file manager if u have one, navigate to the android folder, select the program CLRCAD, (it will not do anything that you can see)
Then select the Zharet program.
Lay the phone down!
Sit back and wait, you will see text fly across the screen, the flash might flash, screen might fade and then come back.
Once linux is done loading and mapping out the hardware, android should be up and running.
Sign in to google and your contacts will sync if you have any on there.
Android is not perfect yet BUT it has come an amazing way since the beginning of the month.
I am using the current settings in WM, if you can do the same and you should have no problems.
SA TMOBILE HD2
HSPL2, I know HSPL3 is/has been out and is recommended, but is there any advantage in using it, i don't want to change if i don't need to
Radio 2.10.50.26
O.S. 5.2.21908 (21908.5.0.93)
Manila 2.5.20161332.0
Energy.Leo.21908.Sense2.5.Cookie.Jul.16 (absolutely love the energy roms, always updated and he includes the program to back up all settings making the update flashes a pleasant experience)
i ALWAYS TASK 29 before all roms!
CLASS 4 or better sd card.
When ever you want to load android, you must do so by selecting the two files mentiond above after a clean boot and always clrcad.exe first.
Sometimes android will not boot correctly, remember it was not designed for this phone.
Also all settings you make, programs you download, ect will stay in android
Pictures and such will be shared between android and wm.
Trying...
I'm installing it now per your instructions. A couple of concerns you might be able to help me with. I could not find the program CLRCAD in any folder, ok I couldn't find an android folder either. I went to my SD card where I had extracted the froyo & copied over the Zimage, I didn't see a Zharet program but I did see a haret file that looked like a program so I clicked on it and it started to download Linux! I hope I did it correctly even though it seemed slightly different. am I going to run into trouble not having run the CLRCAD?
Thanks for all your hard work.
Guess I answered part of my question. It did not install correctly. I'll look for a CLRCAD and retry.
cant believe im back in the winmo forum once again.ran HARET froyo last night on my HSPL2 Leon RoM,and wow.with wifi i was browsing,playing 3d games(flawless compare to my EVO 30fps capped),and watching youtube.really loving it.glad no one bought my HD2 but now its a keeper.
BigB4400 said:
I'm installing it now per your instructions. A couple of concerns you might be able to help me with. I could not find the program CLRCAD in any folder, ok I couldn't find an android folder either. I went to my SD card where I had extracted the froyo & copied over the Zimage, I didn't see a Zharet program but I did see a haret file that looked like a program so I clicked on it and it started to download Linux! I hope I did it correctly even though it seemed slightly different. am I going to run into trouble not having run the CLRCAD?
Thanks for all your hard work.
Guess I answered part of my question. It did not install correctly. I'll look for a CLRCAD and retry.
Click to expand...
Click to collapse
I Found CLRCAD ( I think I was just a little sleepy last night when I was trying this) I ran it and it loaded correctly. Wow it seems to run great! I am running Touch-X Extreme ROM and have some issues with the phone(it doesnt work, I have no antenna). I will try loading energy's rom (since so many people have got the phone to work well with his) and see how well it works out.
Good luck!
Do we really need to format our SD card? If we don't what would happen to the data already on there?
is the "zimage" provided for both dan's froyo and desire v4?
which files do i replace with the new zimage?
After a few days of use, this build seems to run fine. Except for a few things. 1) my phone tends to run real *hot* after using Android. And second, after about 5 min of idling the screen goes black and there seems like there's nothing I can do about except to reboot. I can't even push any of the bottom buttons, that doesn't work either. on. It will run just fine as long as I don't let it sit to long without touching the screen. Is this normal or am I doing something wrong? I can't wait for a even more stable build.
why cant i sign into google and other networks and why is it running overclocked? help me out yall got daaaamn lol. thanks
Is Paradoxua's Froyo build more stock than daniel's? Because daniels' uses ADW, which I'm not too fond of.
Also, is anyone else experiencing weird scrolling issues? Like you flick down a list and it's supposed to go flying down, but it only goes down like a tiny bit.
Another issue, when the screen turns off while you're connected to PC, the phone seems to disconnect too. I assume this is a WinMo issue because in WinMo when you connect your phone to your PC the screen is always on.
Thread moved to General.
i got my hd2 to load android just fine.. but the screen is very dim.. any ideas??
maybe you can toggle the backlight settings in winmo.. idk. it works for the tp2.
I always get the green screen or death or it enters android and quickly says powering off. And shuts off.
jaadamoo said:
i got my hd2 to load android just fine.. but the screen is very dim.. any ideas??
Click to expand...
Click to collapse
you need to make sure automatic light is off in win mo before you boot up android and i always leave it at around 60% and it works fine.
I have also been having some scrolling issues. It goes down a tad bit and if you hold the screen for a fraction of a second too long after first setting your finger on the screen, then it acts as if you did a holding touch.
Also the 3g is very very slow, kinda makes the market place useless since it takes for ever to download something. Wifi downloading is working.
New zimage file
Try replacing your current zimage file with this one.
http://cotulla.pp.ru/leo/Android/Cotulla_zImage_CABDET_NOSPEEDDY.rar
Just replace/override it on your sd card.
Also delete your cache folder and your data file.
You will loose your information inside of android, like doing a reset of the OS.
Check this http://cotulla.pp.ru/leo/Android/ often, fair warning many people are having problems with the newer image marked(7-25)
Some roms or radios wont work for sure!
I am now running MIRI rom wm6.5 V17.6 with radio 2.12.50.02.2 and I must say very impressive how far you devs have come in a few weeks. Phone is working with audio and WIFI. I had stock rom TMO 2.13 installed with radio 2.10 and although Android loaded and ran fine I did not have audio during calls,they sounded robotic at times or no audio at all. I am not sure if it was the radio upgrade or switching the ROM to MIRI that did the trick. I have been playing with phone for approximately six hours nonstop and it has been solid...
Gen. Y DualBOOT Implementation
Does the app work well the newer builds?
Btw a very BIG thank you all the guys working on this, you guys are freaking AWESOME!
acessford101 said:
Try replacing your current zimage file with this one.
http://cotulla.pp.ru/leo/Android/Cotulla_zImage_CABDET_NOSPEEDDY.rar
Just replace/override it on your sd card.
Also delete your cache folder and your data file.
You will loose your information inside of android, like doing a reset of the OS.
Check this http://cotulla.pp.ru/leo/Android/ often, fair warning many people are having problems with the newer image marked(7-25)
Click to expand...
Click to collapse
Thanks, I was using the Jul 19 zImage.rar file. I'm about to try this one and see if it makes a diff.
anyone know how to get the data connection to work for T-Mobile on the Android desire v5? I go into APN settings but it always requires a username and password but t-mobile doesnt use a username/password for apn.
OK FELLAS,
i'm not a noob. been flashing for a while now and am pretty much tech savvy, but this one has me for a loop. recently, my phone just started doing this; i can install and launch any and all android builds so readily available here from the XDA chefs. EVEN the DARKSTONE DESIRE HD BETA 2 worked and i played with it for an hour or so. HERE IS THE PROBLEM; i used to in the beginning be able to boot android over and over and over with my android launcher icon thats built into the current energy rom im using. (24631 04 sep) however now after a reboot, I run into a brick wall with the prompt that reads "cant find rootfs. you need to unzip a rootfs file to your memory card. job control turned off"
here are the things i have tried to remedy this:
1. format card= didnt fix
2. try a different card= i have 3 different cards; this didnt fix it either.
Only thing i havent tried which i am reluctant to try is task 29 and reload the WINMO ROM.
ANYONE ELSE OUT THERE EXPERIENCING THIS AND IF SO, HOW DID YOU FIX IT?
bluevmax92 said:
OK FELLAS,
i'm not a noob. been flashing for a while now and am pretty much tech savvy, but this one has me for a loop. recently, my phone just started doing this; i can install and launch any and all android builds so readily available here from the XDA chefs. EVEN the DARKSTONE DESIRE HD BETA 2 worked and i played with it for an hour or so. HERE IS THE PROBLEM; i used to in the beginning be able to boot android over and over and over with my android launcher icon thats built into the current energy rom im using. (24631 04 sep) however now after a reboot, I run into a brick wall with the prompt that reads "cant find rootfs. you need to unzip a rootfs file to your memory card. job control turned off"
here are the things i have tried to remedy this:
1. format card= didnt fix
2. try a different card= i have 3 different cards; this didnt fix it either.
Only thing i havent tried which i am reluctant to try is task 29 and reload the WINMO ROM.
ANYONE ELSE OUT THERE EXPERIENCING THIS AND IF SO, HOW DID YOU FIX IT?
Click to expand...
Click to collapse
What Rom radio you using?
Are you using an auto boot or multiboot
Are you renaming the folder to Android and putting that folder on root? And dies your startup file read rel_path=android
If all correct
Seems like task29
And new Rom radio is the answer
Sent from my HTC HD2 using Tapatalk
whynot66 said:
What Rom radio you using?
Are you using an auto boot or multiboot
Are you renaming the folder to Android and putting that folder on root? And dies your startup file read rel_path=android
If all correct
Seems like task29
And new Rom radio is the answer
Sent from my HTC HD2 using Tapatalk
Click to expand...
Click to collapse
Radio_2_12_50_02_2
AND ROM IS ENERGY 24631 04 SEP 2010
HSPL3
ALSO AN UPDATE; REFLASHED 24631 UPDATED DATE,TIME,QUICK GPS, AND THEN GET THIS; IT BOOTED DESIRE HD ROM SUPER QUICK BUT OTHER BUILD IM USING Core_Droid_V.0.2 STILL DIDNT WORK. IM GONNA TRY DROPPING ANOTHER ROOTFS.IMG ON THE CARD AND TRY AGAIN.
I had a similar problem, the problem was that I had unzipped the contents of the "android" folder to the root of my SDcard. What I should have done was copy the folder to the root of the SDcard, after I did this it worked perfectly
I have the same problem here, but not only with the DARKSTONE DESIRE HD BETA 2 ROM. A lot Android ROMs boots great the first time, but after a phone reboot I was unable to boot the Android ROM again.
It shows me these message: "cant find rootfs. you need to unzip a rootfs file to your memory card. job control turned off" or the boot loader freezed completely with some stripes on the screen. any ideas?
RAIDO: 2.08.50.05
ROM: Artemis 30.0 GER (5.2.23576)
Update:
Got a solution from this thread: http://forum.xda-developers.com/showthread.php?t=788764
Just extract your DARKSTONE DESIRE HD BETA 2 ROM into "/Storage Card/Android" and boot it. done!
All you have to do is delete the android folder everytime you boot up android. I was running into the same thing after the initial setup worked good but wouldn't boot back after I went back to windows.
Sent from my HD2 running Darkstone Froyo V2.1
OK, here is my problem.
UK HD2 -> Generic running 1.66 stock, with HSPL 2.08, and Radio 2.12.50.02.
I have been running many of the different Android builds on my phone since the first one came out with no problems, until now...
My phone will not run any of the new ones at all. They give the instruction to leave on first boot to create the data store, takes about 5-10min. I have left my phone for hours with a faded black screen, with a few lines on it, but it never gets any further than that.
Have tried:
Mattc Leo + Froyo 1.5*, 1.6*, 1.7 and 1.8
Mattc Evo 1.0.1
Mattc NexusLeo 1.1
Mdeejay Froyo Sense 2.2
Mdeejay eVo 1.0
FroyoStone Sense 1* and 2
Darksotne HD2Froyo 2.1*
Darkstone DesireROM 2*, 3*, 4* and 5*
*= ones that have worked
It seems to me that something has changed with all the newer ROMS that are stopping them from working for me. I have format my SD every time i try a new ROM and have even hard reset my WinMo to see if that the problem -> Nothing works!
As Marvin would say: "I just want you to know, i am feeling very depressed today"
Help please
SquithyX said:
OK, here is my problem.
UK HD2 -> Generic running 1.66 stock, with HSPL 2.08, and Radio 2.12.50.02.
I have been running many of the different Android builds on my phone since the first one came out with no problems, until now...
My phone will not run any of the new ones at all. They give the instruction to leave on first boot to create the data store, takes about 5-10min. I have left my phone for hours with a faded black screen, with a few lines on it, but it never gets any further than that.
Have tried:
Mattc Leo + Froyo 1.5*, 1.6*, 1.7 and 1.8
Mattc Evo 1.0.1
Mattc NexusLeo 1.1
Mdeejay Froyo Sense 2.2
Mdeejay eVo 1.0
FroyoStone Sense 1* and 2
Darksotne HD2Froyo 2.1*
Darkstone DesireROM 2*, 3*, 4* and 5*
*= ones that have worked
It seems to me that something has changed with all the newer ROMS that are stopping them from working for me. I have format my SD every time i try a new ROM and have even hard reset my WinMo to see if that the problem -> Nothing works!
As Marvin would say: "I just want you to know, i am feeling very depressed today"
Help please
Click to expand...
Click to collapse
show us your step by step procedure in running android, so people when they see it may know at which point you may be making an error.
also, after reading this
post, I came to the conclusion that indeed many left
over junks in winmo are messing up the process of Android running, so I took it to mean that we have to do a Task 29 every time we try a build.
make sure the android build is in a folder marked android the older roms went on the root of the sd! another thing is when haret boots see if the writing says failer to mount sd and get back to me or pm me well figure it out!!
Definitely task29 that sucker. Also consider a "meant for android" WM rom like chuckydroid. Radio 2.14 is now available if you want to try something else.
polo735 said:
Definitely task29 that sucker. Also consider a "meant for android" WM rom like chuckydroid. Radio 2.14 is now available if you want to try something else.
Click to expand...
Click to collapse
Yeah, I was going to suggest task 29 and then reinstall a different WM Rom.
I am using the 2.14 radio with great results.....
Good Luck.
try new sd card
I can understand your frustration, If the task 29 alone does not help, I would get a new sd card, I have read its best to long format card, task 29 phone, install your windows rom of choice( I like chuckys android), then install android. good luck
Steps taken so far
Ok, first off, Thank you all for your responses!!!!
Was expecting to get flamed, as i had searched the forums and could not find anything myself but expected there to be something somewhere, that somebody knew about.
With the older ROMS that are stored on the root of SD, i formatted the SD and copied the data over using SD adaptor in my MacBook Pro's SD slot -> Worked like a charm!!
With the newer ones, that have worked anyway the procedure was the same, format SD and copy Android folder over from Mac -> again worked like a champ!
But now with these new ones i have tried the old methods of format and copy using SD adaptor, tried formatting and coping the Android folder on to the phone using the USB connection on the phone, tried renaming the "Android" folder "android".
I have not updated or changed the WinMo ROM, but i have reloaded it, when i found out about this problem. I task 29 and then reflashed with the stock 1.66 and still no dice.
Step by step for last ones i have tried:
1. Power off phone and remove battery (not needed i know but hay)
2. Remove SD card and put in SD adaptor
3. Insert into Mac and format card Fat (Mac Fat = Win Fat32)
4. Unarchive Android ROM and copy to SD - (/StorageCard/Android)
5. After copy complete wait for 5min then eject SD (i like to make sure there is nothing in the buffer)
6. Put into phone, put battery in and power up (normally with the battery cover off lol)
7. Wait for the unfortunate Windows logo and phone to boot up ("Launching HTC Sense" seems to take forever)
8. As soon as phone started either run the Android icon from Sense or open File Explorer and run both programs
9. HeRET starts, screen goes black see txt (guess bootloader loading the kernel) for 1 second then screen fades to black with faint lines running down it (backlight on very dull)
10. Wait...wait...wait (Mattc Leo Froyo 1.8 waited 20min, then fell asleep and when i awoke 5hours later it was still the same)
I dont get it, so to recap i have formatted my SD every-time i have tried, i have task29 my phone about a week ago, tried many of the ROMS on here and nothing, i have tried one of the old ones and that works though!!!!
Arrrgg, Please somebody point out what stupid thing i am doing wrong.
"Even the doors don't like me!"
Could this be it?
I have spent more time reading forums and such like, could it be due to the fault described here in this post?
http://forum.xda-developers.com/showthread.php?p=8264796
If you are using a standard stock 1.66 rom your radio may not be compatable. I had the same issue to start off with. Would boot half way then die. I upgraded my radio now using 2.14 and can boot no problem at all.
SquithyX said:
Ok, first off, Thank you all for your responses!!!!
Was expecting to get flamed, as i had searched the. . . . . . or changed the WinMo ROM, but i have reloaded it, when i found out about this problem. I task 29 and then reflashed with the stock 1.66 and still no dice.
Step by step for last ones i have tried:
1. Power off phone and remove battery (not needed i know but hay)
2. Remove SD card and put in SD adaptor
3. Insert into Mac and format card Fat (Mac Fat = Win Fat32)
4. Unarchive Android ROM and copy to SD - (/StorageCard/Android)
5. After copy complete wait for 5min then eject SD (i like to make sure there is nothing in the buffer). . . . .
Click to expand...
Click to collapse
I have experimented with Stock UK WWE 1.66 about two weeks ago, and no matter
what Radio and HSPL I put on it, once I clicked on Haret, it goes exactly like you describe it
White faint lines all over the screen which seems like very fine drops of rain.
you can always try Winmo ROMs specifically made to be Android friendly.
also it would be valuable if you read this Thread read
at least the first and 13th post
So I've tried to install android build. I had stock rom 3.14.479.2 and I've tried to install HD2Froyo_V3. I've followed the instruction and after running haret few lines of text showed and than nothing, htc display appeared and stayed that way until I've removed the battery. Then I've read that I have to flash a coked Rom in order to install build for android so I downgraded it to 1.48 so I can install HSPL (not sure that it was necessary). I've flashed Energy.Leo.21916.Sense2.5.Cookie.Nov.02 with Radio_2_12_50_02_2 and copied Android folder again, same result. After flashing between stock Rom and Energy.Leo.21916.Sense2.5.Cookie.Nov.02 million of times I'm out of options. The same problem I had with FroyoStone_Sense_V3.2 too. It seemed so easy when I saw it on youtube and I can not believe that I had so bad luck. What I've done wrong? What should I do?
Anyone help?
One word: wait!
the kernel usually creates a 1GB storage for android. This will need some minutes (can take up to 10 minutes on class 2)
Some words for ROMs. Nearly all ROMs will work (the 2.14 ROMs don't) as long as you have a new radio. use 2.10 or higher. some have robo voice problems when calling. if you experience robo try another Radio.
(you should post questions like that in android development discussion. this subforum is for development only)
The folder-name of your rom, what is it and did you change it? You have to change a value in startup.txt aswell if it is different from 'Android'.
Ultimaex is right. Creating a 1gb storage for android will take some time, be patient. I have a 2gb storage which took about 20 minutes from start to finish.
fyi, my setup is tmous stock rom 3.14 and tytung's NexusHD2-FRG83 Froyo 2.2.1 build.
Mr_Q said:
The folder-name of your rom, what is it and did you change it? You have to change a value in startup.txt aswell if it is different from 'Android'.
Click to expand...
Click to collapse
It is Android. And I've been waiting more than 15 minutes and nothing changes, only black screen with HTC on it...
mila1909 said:
It is Android. And I've been waiting more than 15 minutes and nothing changes, only black screen with HTC on it...
Click to expand...
Click to collapse
Ive had this happen to me when I was switching builds. I deleted everything on my sd card that was related to android. Usually, the folders that android makes on your sd card are all lowercase letters. The folders are start with a capital letter are Windows Mobile specific folders. So delete all those folders, dont forget to show hidden files just to make sure you get all the folders. Afterwards, with whatever build you plan on using, its probably best to re-download that build just to make sure no files were edited and copy them to your sd card.
Basically just start with a clean slate and you should be good to go.
i had the same problem just reformat ure memory card on ure htc hd2
I formated the sd every time I tried. It's not that
Same
I got the same problem I have tried everything waited more dan 20 minutes. Formatted 25 times. Iam searching all forums to find something
Ok, I have mentioned this a couple of times and it seems to fix this issue, format the SD card within windows (a full format not a quick one) and ensure that you format it to clusters that are 32kb.
Also what radio are you both using?
I use 2.15.50.14 now, bit tried with every radio over 2.8
fig_jam_uk said:
Ok, I have mentioned this a couple of times and it seems to fix this issue, format the SD card within windows (a full format not a quick one) and ensure that you format it to clusters that are 32kb.
Also what radio are you both using?
Click to expand...
Click to collapse
Iam now trieying what you said. I let u know about it.
I use radio 12.50
nope, again not working...I am desperate
mila1909 said:
nope, again not working...I am desperate
Click to expand...
Click to collapse
Same format didnt help, iam now gonna try other kernels.
well finally works!!! I instaled hspl3 and energy rom and tried with mattcleofroyo1.8 and it happend ...I don't know if it works with another build but this one is good, no problems till now
mila1909 said:
well finally works!!! I instaled hspl3 and energy rom and tried with mattcleofroyo1.8 and it happend ...I don't know if it works with another build but this one is good, no problems till now
Click to expand...
Click to collapse
I got energy rom 2 and hspl3 gonna try that android build i let you know if it works. try to use the zImage from mattcleofroyo with another build.
That build didnt work for me after jumping kernel my leds flashed an i got whit streak.
coolgut said:
That build didnt work for me after jumping kernel my leds flashed an i got whit streak.
Click to expand...
Click to collapse
That's normal at the first boot, he wrote it in his thread.. Was the same for my phone, just let it doin' his thing it will finish after about 10min.
And what I wanted to say, I think mattc 1.8 is one of the best Sense builds out there.. Works so damm' smooth. Old but gold
Yes I agree. I've tried several after this one and got back on mattc...There are few problems but I hope that will be fixed in other versions....
coolgut said:
That build didnt work for me after jumping kernel my leds flashed an i got whit streak.
Click to expand...
Click to collapse
You mean you got all kinds of distorted graphics all over the screen. Black and white stripes kind of thing? If so, that's because you probably replaced zImage but didn't replace initrd.gz. Regardless, if you leave it on the screwed up black/white screen, it should load within 10-15 min.
Hey all,
I'm usually pretty good at figuring these types of things out, but unfortunately I haven't been able to figure this one out yet.
Wifi works fine in WinMo 6.5 and WinPhone 7. I haven't tried SD version of Android, but I'd rather not go that route as I want to be able to use a fully functioning NAND version of Android.
I have done Task29/wipe data/cache/dalvik cache on many occasions, repartitioned, reinstalled WinMo 6.5 and then started over with MAGLDR (latest version), replaced wifi module libraries, but nothing has proven to work. Everything else is perfect, though.
Somebody has to have experienced this before? I couldn't find much in terms of a solution by searching.
Thanks!
What HD2 Radio version are you using?
What Android ROM are you using?
Have you made sure that it is a MAGLDR version you are trying to install, not the cLK version?
Why would you need to replace the WiFi module librarys as your ROM should work without error after installation?
A bit more info and we should be able to sort this one out!
custommsp said:
Hey all,
I'm usually pretty good at figuring these types of things out, but unfortunately I haven't been able to figure this one out yet.
Wifi works fine in WinMo 6.5 and WinPhone 7. I haven't tried SD version of Android, but I'd rather not go that route as I want to be able to use a fully functioning NAND version of Android.
I have done Task29/wipe data/cache/dalvik cache on many occasions, repartitioned, reinstalled WinMo 6.5 and then started over with MAGLDR (latest version), replaced wifi module libraries, but nothing has proven to work. Everything else is perfect, though.
Somebody has to have experienced this before? I couldn't find much in terms of a solution by searching.
Thanks!
Click to expand...
Click to collapse
Hey. Thanks for joining!
- Radio 2.15.50.14 and one of the older ones which was installed when I picked up this phone
- Roms:
NDT MIUI Froyo V6.2 currently.
Tried [CWR] BOYPPC-SHIFTPDA_GINGER 2.3.4-Sense.s V29 (12.Jun), CMYLXGO's Stock Desire HD(2) NAND ROM v1.1.17 and a few others i can't remember. All MAG versions.
I tried replacing the libs, because i've read that as part of a fix for related wifi problems from earlier this year.
Thanks!
custommsp said:
Hey. Thanks for joining!
- Radio 2.15.50.14 and one of the older ones which was installed when I picked up this phone
- Roms:
NDT MIUI Froyo V6.2 currently.
Tried [CWR] BOYPPC-SHIFTPDA_GINGER 2.3.4-Sense.s V29 (12.Jun), CMYLXGO's Stock Desire HD(2) NAND ROM v1.1.17 and a few others i can't remember. All MAG versions.
I tried replacing the libs, because i've read that as part of a fix for related wifi problems from earlier this year.
Thanks!
Click to expand...
Click to collapse
You have the most common Radio 2.15.50.14 so that isn't the problem.
The fix is mainly for cLK versions so it could use the PPP interface but if you are using MAGLDR then that isn't needed - this alone could be your problem, I reccomend not installing this patch any more?!
I play with roms a lot and normally my errors are due to using a kernel which the rom wasn't developed for - or more recently, frequent drops to the internet.
When my drops happened, I had done nothing different but it seems that a change in CM7 source now addressed my routers security settings differently - I have no idea when it was added and I was lucky enough to find a firmware update for my router which solved the problem.
Out of interest, when you click on wifi, does it say error or does it try to connect and randomly drop? Error would indicate a kernel/radio/hardware problem and dropping or not connecting would possibly indicate router problem.
Possibly, one of the best places to start is the security settings of your router, disable all security and see if it will connect... if it does then apply security - I use WPA2 PSK TKIP and it now works for me!
NDT MIUI Froyo V6.2 & CMYLXGO's Stock Desire HD are quite old (In terms of development), BOYPPC-SHIFTPDA_GINGER 2.3.4-Sense.s V29 is new and updated frequently so i'm unsure why all would have the same problem?!?!.
You could also try my rom located in my signature "HardDroid2" as I have extensively tested this and have no problems (Not trying to punt my rom at all!).
If changing your router settings or no other roms work then it is beyond me as there are only a few combinations af possible hardware/software faults!
Hope this helps
Already installed Is the phone supposed to boot in Airplane mode enabled for the first boot?
Ok, unfortunately the same issue with WiFi. What happens when i turn wifi on is it takes about 15 seconds for the check to appear in the box, then it stays on for about 15 more seconds with no networks showing, then it turns off automatically. The same thing with every rom I've tried, unless I start messing with libs or conf files at which point I get "error" or it doesn't turn on at all.
Thanks!
custommsp said:
Already installed Is the phone supposed to boot in Airplane mode enabled for the first boot?
Thanks!
Click to expand...
Click to collapse
Ummmm... NOPE!
I think your problem is with your radio rom. I would reccomend starting from scratch!
This is what I do and it works fine for me:
Prep SD Card: Format FAT32 and also create a 1GB Ext3 Partition (For apps2SD if needed)
Copy the rom update.zip to FAT32 partition of SD Card & Insert into phone.
Run HSPL3_PKG.exe and install HSPL 2.08
Flash Radio_Leo_2.15.50.14
Run Task 29 - wipe phone
Install MAGLDR 1.1.3
start device (Hold down power button until menu list appears) choose USB Flasher
Install Recovery 150MB System/5MB Cache (ClockworkMod Recovery v4.0.0.0)
Start MAGLDR (Hold down power button until menu list appears) Select "AD Recovery"
Boot ClockworkMod and install update.zip from SD Card.
I'm not trying to teach you how to suck eggs... but maybe there is a little step you may of missed?!?!?
deano309 said:
Ummmm... NOPE!
I think your problem is with your radio rom. I would reccomend starting from scratch!
This is what I do and it works fine for me:
Prep SD Card: Format FAT32 and also create a 1GB Ext3 Partition (For apps2SD if needed)
Copy the rom update.zip to FAT32 partition of SD Card & Insert into phone.
Run HSPL3_PKG.exe and install HSPL 2.08
Flash Radio_Leo_2.15.50.14
Run Task 29 - wipe phone
Install MAGLDR 1.1.3
start device (Hold down power button until menu list appears) choose USB Flasher
Install Recovery 150MB System/5MB Cache (ClockworkMod Recovery v4.0.0.0)
Start MAGLDR (Hold down power button until menu list appears) Select "AD Recovery"
Boot ClockworkMod and install update.zip from SD Card.
I'm not trying to teach you how to suck eggs... but maybe there is a little step you may of missed?!?!?
Click to expand...
Click to collapse
Much appreciated, I'll give this a try.
custommsp said:
Much appreciated, I'll give this a try.
Click to expand...
Click to collapse
I would reccomend re-downloading the files, especially the radio rom as I have a feeling it may be corrupted - don't know why it would work on WP7 though??
Use the HSPL3_PKG.exe to install HSLP 2.08 as it is regarded as the best.
I use Loader 2.10 KSubedi (MAGLDR 1.1.3 Debranded) just for asthetic reasons.
We will get there!!! lol
Same deal, unfortunately. I've noticed that the mac address is "unavailable" at all times, including the 10 secs the wifi is actually on (according to the switch)
custommsp said:
Same deal, unfortunately. I've noticed that the mac address is "unavailable" at all times, including the 10 secs the wifi is actually on (according to the switch)
Click to expand...
Click to collapse
Did you re-download the radio from here?: http://www.multiupload.com/QP0IWGY42F
I don't understand why your wifi works under wm6.5 (which installs during flashing rom) & WP7 (which runs the same way as android nand) but not under android... I would of classed it as a corrupted file and im completely at a loss!!!!
It can't be a hardware fault and there isn't any differences in earlier/later versions of the HD2's wifi module!!!
OK, I admit it.... I'm stumped!
deano309 said:
Did you re-download the radio from here?: http://www.multiupload.com/QP0IWGY42F
I don't understand why your wifi works under wm6.5 (which installs during flashing rom) & WP7 (which runs the same way as android nand) but not under android... I would of classed it as a corrupted file and im completely at a loss!!!!
It can't be a hardware fault and there isn't any differences in earlier/later versions of the HD2's wifi module!!!
OK, I admit it.... I'm stumped!
Click to expand...
Click to collapse
Yep, that file. Maybe I need to install the latest Tmobile 6.5 rom and start from that?
custommsp said:
Yep, that file. Maybe I need to install the latest Tmobile 6.5 rom and start from that?
Click to expand...
Click to collapse
If you install the latest rom and then task 29, you still have the radio version which installed with the rom as task 29 doesn't touch that section!
I remember a couple of years ago when I changed the wifi module on a PSP that it no longer held a mac address when using original Sony firmware... has your device been in for repair?
Just a thought really, i'm grabbing at straws since it really doesn't make sense to me!
deano309 said:
If you install the latest rom and then task 29, you still have the radio version which installed with the rom as task 29 doesn't touch that section!
I remember a couple of years ago when I changed the wifi module on a PSP that it no longer held a mac address when using original Sony firmware... has your device been in for repair?
Just a thought really, i'm grabbing at straws since it really doesn't make sense to me!
Click to expand...
Click to collapse
I'm not sure about its history as I bought it used. Tomorrow is another day with more opportunities to resolve this issue.
Nothing changed by me installing a stock T-mobile WinMo 6.5 then going through the process of converting to NAND android. I found out that I'm not able to save a manual Wi-Fi network entry. Maybe this is a clue for the problem?
Thanks!
custommsp said:
Nothing changed by me installing a stock T-mobile WinMo 6.5 then going through the process of converting to NAND android. I found out that I'm not able to save a manual Wi-Fi network entry. Maybe this is a clue for the problem?
Thanks!
Click to expand...
Click to collapse
Well looking into the kernel, it seems that it will create a custom MAC address for each device to get past the 00:11:22:33:44:55 issue (I don't know what variables it would use to create this but possibly imei???)
There are no really adjustable settings in wpa_supplicant.conf which would help (As far as I can see)
Since you aren't showing a MAC address, it would indicate a problem with your hardware (as no other device has this problem) But why Windows roms would still work is beyond me and the only change in hardware revisions over the life of the HD2 has been to the lcd screen and not the radio hardware.
I have searched and tried to find more information on this but i'm unable to find a conclusive answer or solution
Here is a thought: Download the files which I use from here: http://www.andbuddy.com/files/FOBBu1308083933.html
This contains all the files which I use and a small guide - Please follow ALL the steps as this has given me a 100% working device!
If it still doesn't work after this then I will have to admit that i'm beaten
deano309 said:
Well looking into the kernel, it seems that it will create a custom MAC address for each device to get past the 00:11:22:33:44:55 issue (I don't know what variables it would use to create this but possibly imei???)
There are no really adjustable settings in wpa_supplicant.conf which would help (As far as I can see)
Since you aren't showing a MAC address, it would indicate a problem with your hardware (as no other device has this problem) But why Windows roms would still work is beyond me and the only change in hardware revisions over the life of the HD2 has been to the lcd screen and not the radio hardware.
I have searched and tried to find more information on this but i'm unable to find a conclusive answer or solution
Here is a thought: Download the files which I use from here: http://www.andbuddy.com/files/FOBBu1308083933.html
This contains all the files which I use and a small guide - Please follow ALL the steps as this has given me a 100% working device!
If it still doesn't work after this then I will have to admit that i'm beaten
Click to expand...
Click to collapse
Before doing all of this I have decided to try a SD version of Android. It's producing the same result!
I'm have the same problem . please help us
spellcaster said:
I'm have the same problem . please help us
Click to expand...
Click to collapse
I'm suspecting that the actual wifi related hardware is damaged somewhere, maybe the coaxial cable, at least in my phone.
Do you try solution : http://forum.xda-developers.com/showthread.php?t=827521
i try but i can't do step 6 :
"6. Go to menu Device -> File Explorer. New window will come up."
it not show file
- I Think problem relate with hardware because with the same Room , same Radio , same Wif network other device ok but of me false
- If you have new information or new SOLUTION please send email for me [email protected]
Thanks