Database Users

[Q] Phone storage full

Hi, I recently installed NAND android build and I'm facing similar problem which I had on SD (this happened to me just 1 out of 3 sd builds). When I want to change my wallpaper (stock walls), I get only few thumbnails and I'm able to set wall only from those which get one. When clicking on those without thumbnails, phone says that my storage is full, although it's a clean and fresh install. Does anybody know what to do about it? Thanks

what build did you install?

NAND is HD2 CoreDroid Desire HD GB V2...and before I used SD MccM 4.5

Danibor said:
Hi, I recently installed NAND android build and I'm facing similar problem which I had on SD (this happened to me just 1 out of 3 sd builds). When I want to change my wallpaper (stock walls), I get only few thumbnails and I'm able to set wall only from those which get one. When clicking on those without thumbnails, phone says that my storage is full, although it's a clean and fresh install. Does anybody know what to do about it? Thanks
Click to expand...
Click to collapse
okay..there has something about the recovery.
different size of ROM use different setting of recovery.
you may decompress the recovery.
for example. Recovery_120M_v3.0.2.4.rar
using TXT to run the (flash.cfg)
comes us:
misc ya 1M
recovery rrecov|ro|nospr filesize recovery-raw.img
boot yboot|ro 5M
system ya 120M
cache ya 10M
userdata ya|asize|hr allsize
not very sure it is exactly same to me.
it say that your storage is full, because of your recovery setting.
assume your ROM is 120MB. but your recovery setting is 400MB. your system is using the space more itself. too much space free from the 400.
same like PC. your disk C is using 390GB from 400GB of your whole disk.
main setting is "system ya 120M"
try to make it small by the size of your ROM.
------------------------------------------------------------------------
if u have reduce the space of system. but still storage full.
try to cut up your sd card to help you phone storage.
cut one GB , and format it as ext2 or ext3 to help your phone.
you know android is running under linux system. and ext2 or ext3 is identified by linux.
so..hope it helps.

I formated my SD in FAT32. Ext 3 was then done in CWM (they say it should be like that) and I used 1024/0 ext 3 partition as they instructed in their guide. Probably just some little mistake during the install process. If there's time tomorrow, I'll try to reinstall it and see what happens.

Danibor said:
I formated my SD in FAT32. Ext 3 was then done in CWM (they say it should be like that) and I used 1024/0 ext 3 partition as they instructed in their guide. Probably just some little mistake during the install process. If there's time tomorrow, I'll try to reinstall it and see what happens.
Click to expand...
Click to collapse
all right
good luck~

Installin a larger ROM help plz... :o/

Im kinda new to this but i have been reading & trying for a few days before asking for help but i feel i am stuck now.
I have gone through the process & installed a small rom with clockworkmod using a 150mb partition & it went ok.
Now i want to install a larger rom eg. pyramid_HTC_WWE_1.35.401.1_v1.5_EU.zip (338mb) using clockworkmod & this is where i have the problem, i have followed the steps but when installing the rom it freezes just under halfway install.
Using bootloader I have now used Task29 for a clean install, then installed MAGLDR113, using MAGLDR i used option 5 (USB flasher) & installed the unzipped () to make a partition for the larger rom.
After reboot i went to magldr option 8.AD Recovery & loaded clockworkmod, advanced then partition SD card, chose EXT size=1024, swap size=0M then rebooty.
Now am i supposed to see 4 partitionson my SD card because i cant?
one page i read that i should now transfer my ROM.zip to my Sd card, & i also read on another page that i should go to "mounts & storage" & chose "format sd-ext" I have tried both ways!
With the rom.zip on my card, i chose the "install zip from sdcard" option etc, it installs to just under half way then just stays there for ages, how long should this take for a 338mb zip file?
So i giveup, battery out & try it with a smaller zip (hyperdroid-cm7) 69mb zip & it installs ok, so where am i goin wrong??
Q1, after partitioning the SD card am i supposed to see 4 partitions on the card? because i dont, maybe i should partition it on my pc, do i just divide it into 4 partitions & name then ext, ext1, ext2, ext3? or is there a guide for doin it on ur pc?
Q2.can anyone see where else i might be going wrong?
I feel i am just doin the same thing over & over so thanks for any help you can give.
Something strange i have noticed that if i use the HD2 toolkit to try & create a 400mb partition i get an error sayin something about not enough space, i have to use a seperate Recovery_400M.zip that i downloaded from the NFEUMAN pages?

first of all your sd card patition is right. you must have 2 partitions, fat 32 and sd-ext. now in hd2 nand tool kit choose mgldr partition size as 'custom' then cache size 5MB then click repartition in usb flasher mode then write 190 in the opening window not 400. that's all.

I have managed to get the rom to bootup now after waiting for ages, but when booted it says the memory is low so im guessing its not using the SD card, when i look at the SD card i do not see any partitions so the partitioning tool in clockworkmod hasnt worked, is there a better way to partition the SD card for use with the rom?

you can see the partition in your sd by root explorer apk. or you can dowload to your pc mini tool partition magic an you can manage your partitions. windows doesn't see it.

Theres no mention when partitioning your SD card that you wont be able to see the partitions, i think they should mention that in the tutorials.
I downloaded gparted to partition my SD card & when i loaded it i could see that it had in fact worked when i had done it before.
I installed Apps2SD+ to see if it would sort out the low memory problem but the phone wouldnt boot, i waited 20 mins but it just stayed at the strtup screen.
I am doin it over again now with the partition size you suggested so hopefully this will work, should this allow more space for apps with this partition size?

i used the rom you try to use a few days ago. you dont have to install apps2sd etc. the rom just do that. so wipe everything and flash the rom, you will not face any room problem. to free some ram,you can use built in task manager or a task killer.

Hey mutil i have reinstalled the rom & it seems to be working great, but how do i use apps2SD? when i install new apps will they automaticly be installed to the SD card now, or do i have to chose the options somehow? thx.

yes they will go directly to sd-ext. if some applications like angry birds give force close error then get titanium backup from market, find the app that gives errorin titanium, long press on the app then choose 'move to sd'.

mutil thx for that advise. i just wanna ask you, before you installed the rom, what size clockwork mod recovery partition did you use? I used 190 as suggested above, but now reading back through the thread i see you can use a 170mb partition. Is it would be worth me doing it again as a 170mb partition, would i get any benifit do you think?

It doesn't worth to make a new partition. There will not be a great difference. Good luck.
Sent from my HTC HD2 using XDA Premium App

problem with partition

ext3 partition doesnt support on gingerdx......
please give me instruction how to make it support??? please....
cwc partition wont support.................

EXT3 partitions is supported. I'm currently using GingerDX v006 with an 8GB card with 2 partitions (first FAT32, second EXT3).
Partitioned and formatted in Windows environment.
If you are coming from stock rom or other rom you should do full wipe and also re-format the ext3 partition.

Any help? I partition sdcard with fat32(primary) and Ext3 around 470mb(primary) in Windows then install rom and everything alright then install some apps. Then, when i reboot, its stuck on boot logo. I'm using Froyobread23b and I also tried partitioning with CWM (512mb ext), Zero swap, and again everything fine at first Installed apps, I looked at root explorer data/app and it save on sd..then after some time I reboot then stuck on logo again I've done it about 6 times already and i'm tired any help???? Is it not ok with FroyoBread??

moaj said:
Any help? I partition sdcard with fat32(primary) and Ext3 around 470mb(primary) in Windows then install rom and everything alright then install some apps. Then, when i reboot, its stuck on boot logo. I'm using Froyobread23b and I also tried partitioning with CWM (512mb ext), Zero swap, and again everything fine at first Installed apps, I looked at root explorer data/app and it save on sd..then after some time I reboot then stuck on logo again I've done it about 6 times already and i'm tired any help???? Is it not ok with FroyoBread??
Click to expand...
Click to collapse
try with swipe 32

ithunter said:
try with swipe 32
Click to expand...
Click to collapse
what swipe 32?

Use CWM, it worked for me. Backup data on sd card first. And please set swap to 0.

SpyderX said:
Use CWM, it worked for me. Backup data on sd card first. And please set swap to 0.
Click to expand...
Click to collapse
Yes it also works for me. But after some time when i reboot it's stuck on logo again, and i need to reflash the rom

[Solved] Data2SD on ICS causes device to hang on bootscreen

Hello,
I've installed ICS now without any problems, but after installing the data2sd script and then rebooting my phone gets stuck in the boot animation. Even though it's very beautifull eyecandy it really isn't doing much for me.
I did a full wipe! Clear data/factory reset, Clear dalvick cash, etc. Also Task 29 and used HD2 toolkit to create 250MB system partiton with 5MB cache
First I formatted my SD card (8GB class 10) with MiniTool Partition Wizard 7 completely as FAT32 then I partitioned it (with CWM recovery 4.0.0.0) to 2048MB EXT3 with 256MB Swap, formatted that partition again in MiniTool to EXT3
Then I flashed the ROM (NexusHD2-IceCreamSandwich Beta6) to my device without any problem. Booted ICS, rebooted into recovery and flashed Data2SD installer wich didn't give any errors either.
Booted again and now it's stuck in bootscreen, I've waited for at least 45 to 60 minutes before removing the battery and try everything again all over, but with an EXT4 partition just like Yank555 did.
I followed the instructions from this post without flashing APP2SD Killer first since that causes the market to 'hang on app install'
I know there are people how got it to work so it must be something I did wrong! Can anyone give me some good advice?

BTW FYI, I did previously use TyphooN Gingerbread 2.3.3 CM7 A2SD with 1GB EXT partition without any problems...

Hi,
For me it seems you're doing it right...
Your ext4 partition IS a primary partition ? I suppose yes, since CWM will do it that way when you use it to partition your SD card.
Just to be sure, you did reformat the ext3 partion to ext3, or the swap ? I don't know how DATA2SD will react to finding 2 "sd-ext" partitons (more than one ext2/3/4 partiton), never tried that before... If you don't intend to use any swap, you'd rather leave that one out in CWM (choose 0Mb)...
JP.
PS: If you want to use swap (hard swap on a swap partition) I can explain to you how to do that. If you want to do it using a swapfile (once DATA2SD is up & running, you can have a look here).

Tanks for your reply. I don't have much time this weekend due to Christmas shopping and everything But I determent to get this to work! And I won't stop till I do. I'm using this ROM for every day and I just need more space. I found there are more people with the same issue as me, so when I get it to work I'll post my findings in the main development threat as well. But I'll make sure to give you all the credit that is due...

Fixed it! Did had to use sort of a "work-around" but it's working and it's all good! That's most important! If anyone else is looking for the solution for this problem, this is what I used and what works for me!
http://forum.xda-developers.com/showpost.php?p=20439320&postcount=2379
Please give thanks where they are due, that is to the original poster offcourse and not me!

The fixed work-around is App2SD rite? I think it will be good if we can get Data2SD working. I think the latter is faster.
I also read some managed to get Data2Ext working in Tytung ICS Beta7 already. See this http://forum.xda-developers.com/showthread.php?t=1403710
PPKLP said:
Fixed it! Did had to use sort of a "work-around" but it's working and it's all good! That's most important! If anyone else is looking for the solution for this problem, this is what I used and what works for me!
http://forum.xda-developers.com/showpost.php?p=20439320&postcount=2379
Please give thanks where they are due, that is to the original poster offcourse and not me!
Click to expand...
Click to collapse

Yank555 said:
Hi,
For me it seems you're doing it right...
Your ext4 partition IS a primary partition ? I suppose yes, since CWM will do it that way when you use it to partition your SD card.
Just to be sure, you did reformat the ext3 partion to ext3, or the swap ? I don't know how DATA2SD will react to finding 2 "sd-ext" partitons (more than one ext2/3/4 partiton), never tried that before... If you don't intend to use any swap, you'd rather leave that one out in CWM (choose 0Mb)...
JP.
PS: If you want to use swap (hard swap on a swap partition) I can explain to you how to do that. If you want to do it using a swapfile (once DATA2SD is up & running, you can have a look here).
Click to expand...
Click to collapse
hey HD2 expert !! i have the same prob over here , installed data2sd after flashing the rom and stuckin at the boot screen ,,
-anyone find a solution !!!!!!

[Q] Problems with Data2EXT

I've been experiencing the dreaded "Low Internal Memory" problems on my HD2 running a MIUI GB ROM.
I was told this was because the included A2SD, well, sucks. I was advised to use Data2EXT instead. Since I wanted to start with a clean slate anyway, I decided it was time to completely wipe my HD2 and install everything anew. This is what I did:
Wiped the HD2 with Task29 (using the HD2 Toolkit)
Installed ClockworkModRecovery v1.3 150MB (I wasn't sure I actually used the 150MB version when I initially installed CWM Recovery)
Cleared data/cache with CWM Recovery
Reformatted the 1GB sd-ext partition on my SD Card (using MiniTool Partition Wizard)
Installed ROM with CWM Recovery (from zip)
Installed A2SDKiller scripts (from zip)
Rebooted phone into MIUI, but did not install anything.
Rebooted into CWM Recovery and installed the Data2SD Installer.
Rebooted into MIUI again
It seemed everything was fine. If I looked at my memory usage, instead of only 210 MB of total storage I had previously, I now had almost 1GB. I setup my Google account and started to install some apps. Somewhere along the line one of the apps hung the phone so I rebooted it again.
But when it was done rebooting, much to my surprise all installed apps were gone. In fact, the phone was behaving like it was the first time it was started (asking me for my Google credentials again, etc). At first I thought this was perhaps due to the hung app, so I did all the above steps again (including wiping the phone).
Again I installed a few apps, and this time I rebooted the phone to check if all was OK now. It wasn't. Again the phone behaved like it was the first time I booted into the new ROM and all installed apps were gone. I've tried about 5 times now and every single time with the same results.
So what could be wrong here?

just a thought (i havent checked, you can do that) but what type of ext did you create? ext2? ext3? ext4? perhaps data2sd (you called it data2ext in the title, data2sd in the post, , ,which is it? they're probably different) doesnt play nice with whichever one you created?

Hi, and thank you for your answer.
samsamuel said:
just a thought (i havent checked, you can do that) but what type of ext did you create? ext2? ext3? ext4?
Click to expand...
Click to collapse
Ext3.
perhaps data2sd (you called it data2ext in the title, data2sd in the post, , ,which is it? they're probably different) doesnt play nice with whichever one you created?
Click to expand...
Click to collapse
I'm pretty sure they are the same (since took the installation procedure from this forum post and they call it both Data2Ext and Data2SD).
I will check to see if the filesystem matters. Thanks!

I just checked and ext3 should be fine.

Zippy1970 said:
I just checked and ext3 should be fine.
Click to expand...
Click to collapse
Check to see see if there's any script left from old method in system/etc/init.d
This is a complete guess but worth a try
EDIT: this is the script that the A2SD killer removes from system/etc/init.d
delete("/system/etc/init.d/40a2sd");
delete("/system/etc/init.d/03stuff2sd");
delete("/system/etc/init.d/10apps2sd");
delete("/system/etc/init.d/04apps2sd");
delete("/system/etc/init.d/01data2whatever");
delete("/system/etc/init.d/98zipalign");
delete("/system/etc/init.d/02cachedalvikcache");
So make sure that has been removed then try flash the new zip file
Sent from my GT-I9100 using xda premium

wis1152 said:
Check to see see if there's any script left from old method in system/etc/init.d
So make sure that has been removed then try flash the new zip file
Click to expand...
Click to collapse
Yes, all those files have been deleted.

It seems to be working now. I wanted to test if changing the Ext3 partition to Ext2 would make any difference so I fired up MiniTool Partition Wizard again. I wiped the partition and formatted it as Ext2.
Or so I thought.
The partition still said it was Ext3. Then it hit me. I had forgotten that you actually have to "Apply" the changes, which I hadn't done before. So I clicked Apply and it wiped the partition and actually formatted it as Ext2.
I then redid the whole thing (install ROM & A2SDKiller scripts, reboot into ROM, reboot into CWM Recovery and installed Data2SD). And now it seems to be working fine.
Not sure which of the two actions on the Ext partition caused it to start working: the wipe or the change to Ext2.

I spoke too soon. I thought it was working since a reset didn't clear all my installed apps. But if I look at the total storage space, it's back to 216MB total. So it looks like Data2Ext isn't running...

*SIGH*
I'm just about to give up on Data2Ext. First of all, I thought I had figured out what was wrong. For some odd reason, whenever I tried to write to my 16GB microSD card on my computer using an SD adapter, it would crash every now and then. Also, partitioning through MiniTool Partition Wizard often resulted in a "Bad Disk" error. I tried this with 3 different 16GB microSD cards. All experienced the same problems when using an SD card adapter (it wasn't a broken SD adapter because I've tried several).
I then dug up an old external microSD USB card reader I had laying around. Using that, I was able to write to the microSD cards just fine and I didn't experience any problems partitioning either.
Speaking about partitioning, it took me a while to figure out that:
Partitioning through ClockWorkMod Recovery doesn't work properly. The FAT32 partition becomes incredibly slow, and the Ext partition is not recognized by Data2Ext
Ext3/Ext4 partitions don't work with Data2Ext. At least, not on my phone
Ext2 partitions only work if they are set as the primary partition
You must name the partition sd-ext or it will not work
Just a FYI for anyone finding this thread in the future.
Anyway, once I figured that out, I was finally able to get Data2Ext working. Sort of. Let me try to explain.
Previously after I had installed Data2Ext and setup some apps, a reboot of my phone would bring it back to a factory reset state. So all installed apps were gone, just like any settings I had altered. Oddly enough, if I looked at the sd-ext partition I could see the data was still there. It simply wasn't used by the phone. But after I had partitioned the sd-ext partition as Ext2, all was fine. A reboot didn't reset the phone back to factory settings.
So I happily reinstalled all my apps, restored my SMS as well as my WhatsApp backup and thought all was fine now. But I did notice the phone wasn't very stable. Every now and then it would become unresponsive for 10-20 seconds. Sometimes I got an error message that a certain app had become unresponsive and I was offered a choice to either shutdown the app or to wait. And sometimes, the phone would spontaneously reset itself.
Today the phone again became unresponsive. Oddly enough, long-pressing the power button did bring up the shutdown window. So I tapped "Shutdown". Next, the phone hung on "Shutting Down". It didn't come back to live. So I removed the battery lid and pressed the reset button.
After it had rebooted, I was greeted with a factory reset phone again. I was about to throw the phone through the window! But when I did another reboot, all my apps were back again as well as my settings. Except for the settings of my individual widgets. Those had all disappeared for some reason. Also, I got quite a few error messages that some apps had stopped unexpectedly. I rebooted again and again the phone behaved as if it were factory reset. But yet another reboot brought everything back...
I now suspect it has something to do with the phone not being able to mount sd-ext every now and then. Either way, my problems aren't solved yet so any tips are much appreciated.

Zippy1970 said:
*SIGH*
I'm just about to give up on Data2Ext. First of all, I thought I had figured out what was wrong. For some odd reason, whenever I tried to write to my 16GB microSD card on my computer using an SD adapter, it would crash every now and then. Also, partitioning through MiniTool Partition Wizard often resulted in a "Bad Disk" error. I tried this with 3 different 16GB microSD cards. All experienced the same problems when using an SD card adapter (it wasn't a broken SD adapter because I've tried several).
I then dug up an old external microSD USB card reader I had laying around. Using that, I was able to write to the microSD cards just fine and I didn't experience any problems partitioning either.
Speaking about partitioning, it took me a while to figure out that:
Partitioning through ClockWorkMod Recovery doesn't work properly. The FAT32 partition becomes incredibly slow, and the Ext partition is not recognized by Data2Ext
Ext3/Ext4 partitions don't work with Data2Ext. At least, not on my phone
Ext2 partitions only work if they are set as the primary partition
You must name the partition sd-ext or it will not work
Just a FYI for anyone finding this thread in the future.
Anyway, once I figured that out, I was finally able to get Data2Ext working. Sort of. Let me try to explain.
Previously after I had installed Data2Ext and setup some apps, a reboot of my phone would bring it back to a factory reset state. So all installed apps were gone, just like any settings I had altered. Oddly enough, if I looked at the sd-ext partition I could see the data was still there. It simply wasn't used by the phone. But after I had partitioned the sd-ext partition as Ext2, all was fine. A reboot didn't reset the phone back to factory settings.
So I happily reinstalled all my apps, restored my SMS as well as my WhatsApp backup and thought all was fine now. But I did notice the phone wasn't very stable. Every now and then it would become unresponsive for 10-20 seconds. Sometimes I got an error message that a certain app had become unresponsive and I was offered a choice to either shutdown the app or to wait. And sometimes, the phone would spontaneously reset itself.
Today the phone again became unresponsive. Oddly enough, long-pressing the power button did bring up the shutdown window. So I tapped "Shutdown". Next, the phone hung on "Shutting Down". It didn't come back to live. So I removed the battery lid and pressed the reset button.
After it had rebooted, I was greeted with a factory reset phone again. I was about to throw the phone through the window! But when I did another reboot, all my apps were back again as well as my settings. Except for the settings of my individual widgets. Those had all disappeared for some reason. Also, I got quite a few error messages that some apps had stopped unexpectedly. I rebooted again and again the phone behaved as if it were factory reset. But yet another reboot brought everything back...
I now suspect it has something to do with the phone not being able to mount sd-ext every now and then. Either way, my problems aren't solved yet so any tips are much appreciated.
Click to expand...
Click to collapse
I have similiar problem before, The ext partition always failed. Now I used Extended TWRP to create the ext partition, it is stable now.
http://forum.xda-developers.com/showthread.php?t=2120297

I can't get Data2Ext to work. I'm either getting tons of force close errors, or it's not seeing the sd-ext partition at all. I tried with Ext2/Ext3/Ext4 partitions (Ext3 didn't seem to work at all). With or without a swap partition. Nothing worked.
I also tried Data2ExtV2 and even DataOnExt. The result was always a ton of force close errors and a very unstable phone.
So anyone any ideas? It sucks only having 200MB of internal storage.

Hmmmm... That's odd. I just wiped my phone again (Task29), reinstalled MAGLDR, CWM Recovery (150MB) and my ROM without Data2Ext or anything and I'm getting the same force close errors and it's telling me I don't have enough internal storage to install apps.
So apparently there's something else going on with my phone?

What ROM are you using?
Try increasing system partition size!
Sent from my NexusHD2 using xda premium

shanman-2 said:
What ROM are you using?
Try increasing system partition size!
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
Actually, I found out it was because I used the wrong cache size this last time. So it's not the cause of all the other problems, but most certainly the cause of the problems this last time I flashed the ROM.

Ok, I've given up on Data2Ext. I can't get it to work. No matter what I try it's incredibly unstable and slow - if it works at all.

1. Make a backup of your SDCard.
2. Download EXTRecovery here.
3. Unzip it and place the 4EXTRecovery folder in the root of your SDCard.
4. Start MAGLDR, choose option 10, then 1, then 3 and select the folder (4EXT~), then boot from SD in the MAGLDR main menu.
5. In the 4EXTRecovery go to Advanced -> Partition SD Card -> Remove all partitions and start from scratch.
6. 1st sd-ext partition: 1024MB, skip 2nd sd-ext partition, SWAP partition is OPTIONAL, I recommend 256MB.
7. Press Yes and pick: "EXT4".
8. When it's finished, choose: "Print partitiontable" to check if it's actually there.
9. If it's there, go back to the main menu and press: "Install from SDCard".
10. Locate your ROM and install it.
Goodluck.
EDIT: Oh, I just read you've given up on it.. all this work for nothing, lol.
Ohwell, maybe I'm lucky and someone else stumbles upon this and can use it.
EDIT 2: Use DataOnEXT and have a /system size of about 285MB, 300-350MB if you have Bad Blocks!
EDIT 3: Try it with: "Jellybean 4.1.2" by Tytung, definitely works!