Please help, i installed stock WPH 6.5 on my HD2 and it worked fine suddenly i tried to unlock it and the slider freezed i turned it off.... Now i cant turn it on, hard reset , soft reset , cant enter bootloader obiviosly nothing.When im trying to turn it on it just softly vibrates,very,very softly u cant even feel that.Please help i tried to put it in fridge i tried everything i found but it cant boot. PLEASE HELP IF YOU CAN !!!
Plug in the charger? Change battery?
hengsheng120 said:
Plug in the charger? Change battery?
Click to expand...
Click to collapse
I tried everything buy nothing
It sounds like your device had sudden hardware failed. You will probably have to either replace the mainboard or JTAG the device. My money would be on replacing the mainboard as it did boot after you flashed Windows Mobile 6.5 so it being software bricked were you can use JTAG to fix is unlikely.
Related
I attemted to flash my Kjam to WM6 & it went dead. It wont start at all. Kjam Service centre says there is a problem in the mother board and it needs to be replaced for $ 300+........now if flash fails...the ROM must have gone corrupt , what has it to do with the motherboard ?
can anyone throw light on whats the real thing ?
Deven.
take out the battery for hours then re-install it. try to boot in bootloader mode first(3 colors). If it work, it's the time to re-flash the right rom now!
When you start the device up what happens?
Same Problem accured for me!!!!!!!
I installeda new rom and my device didn't power on after that.
What should i do now?
afghahi said:
I installeda new rom and my device didn't power on after that.
What should i do now?
Click to expand...
Click to collapse
Nobody here is providing any details so everything is going to be just a guess. If either of these phones were a G4 and you flashed a rom that tried to update the IPL/SPL then its very likely you have bricked your device. But again, with no information about what rom you were trying to flash, what your IPL/SPL were beforehand, or details about what it means that it won't turn on, everything is just a guess...
Bricked Kjam
its comletely dead.....i had disconnected the battery for a couple of days then connected it but it wont start....i checked the battery using multimeter it is fully charged....neither does it power ON when connected to mains...It doesnt get detected when connected to the USB port..thats obvious since it is not powering up...so cant flash it again.. now m in a fix as to whether to spend another fortune after this sweetheart or keep it in a showcase ....
Deven
( a bricked KJam )
If nothing lights up that looks pretty terminal. :-(
Maybe you could buy a broken Wizard with a working motherboard? Alternatively maybe sell off your mostly working Wizard on this forum to raise money to buy a new device?
Sorry if you can't get it going. :-(
i cant get my wizard to go to bootloader ? is there a way to force it ?
thnx
about: force bootloader.
Hello my friend, please use the search options, is easy to find answer for your questions. Here you will find the solution:
http://forum.xda-developers.com/showthread.php?t=294107
note: use the wiki
hi,
thnx for the help.. i did follow the steps mentioned.. but it styll doesnt wrk. whn i try to flash the rom.. it supposedly looses connection wid the computer .. the screen looses the light buh the wizard is on all the way.. u cant use it though.. buh the lights are still blinkin.. (the wifi and phone)
thnx
hey, my mda doesnt even turn on anymore, do u guys think its the battery but the battery was fine when i flashed it but then it doesnt boot to the window, so i took the battery out and put it back in and it doesnt turn on anymore.. i tried the camera, rest button and other stuffs. do u think my phone is bricked? or i should def. get a new battery and try it out?
I suggest you back to your Official rom first then start over again. I do this many times. Activesync always loose its connection before start flashing. It's a normal procedure. When you mention that your Wizard is still up and on the way, what you mean exatcly? Be more specific bringing point details on where you are stuck for instance. Then I'll try to help you out.
Good luck.
cellphoneman said:
hi,
thnx for the help.. i did follow the steps mentioned.. but it styll doesnt wrk. whn i try to flash the rom.. it supposedly looses connection wid the computer .. the screen looses the light buh the wizard is on all the way.. u cant use it though.. buh the lights are still blinkin.. (the wifi and phone)
thnx
Click to expand...
Click to collapse
Sounds a power problem to me. I've been into this couple of times after being in a bootloader mode for a long time. Plug the Wizard directly into the powerwall to start charging then back to your flashing process first doing with an official rom. I don't think you have bricked it.
joco2560 said:
hey, my mda doesnt even turn on anymore, do u guys think its the battery but the battery was fine when i flashed it but then it doesnt boot to the window, so i took the battery out and put it back in and it doesnt turn on anymore.. i tried the camera, rest button and other stuffs. do u think my phone is bricked? or i should def. get a new battery and try it out?
Click to expand...
Click to collapse
epimazzo said:
Sounds a power problem to me. I've been into this couple of times after being in a bootloader mode for a long time. Plug the Wizard directly into the powerwall to start charging then back to your flashing process first doing with an official rom. I don't think you have bricked it.
Click to expand...
Click to collapse
sry, i forgot to mention that it doesnt even charge too, both powerwall or pc
Try to enter in a bootloader mode by hold on the camera button while pressing the reset button. You'll go to bootloader. If not, remove battery one more time, wait seconds and put it in back. Then, force bootloader again and try to charge through powerwall. You should get an orange light or similar during recharging. Check your model. Hope it helps you this time.
joco2560 said:
sry, i forgot to mention that it doesnt even charge too, both powerwall or pc
Click to expand...
Click to collapse
joco2560 said:
sry, i forgot to mention that it doesnt even charge too, both powerwall or pc
Click to expand...
Click to collapse
which version is it ,G3 or G4,and which Rom were trying to upgrade with.
Well,if its a G3 then,there's some power problem,but if it's a G4 and you tried to flash a Rom with IPL/SPL included,well its a brick.
Yeah...unfortunately zabardast_1 is right about your device. If it is a G4 and you flashed a G3 ROM, you could have bricked your techtoy! Hope you knew what you was doing at that time!
Try to always provide enought information regarding your environment and device so we can help you out better!
All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...
The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...
Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd
I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.
get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it
Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???
Hey guys ! I just have a big problem ... i have so many Hard-reseted my device that the Volume Down Button don't work anymore ...
I Flashed Blackstonehenge 4.4 (like always ^^), It worked fine, like always but this time 1 week after my htc is stuck at the boot screen i can't even get a way to boot it, i can't make a hard reset or even enter in Bootloader mode -_-
Please i really need your help
Sorry if i have a bad english -_-
Nobody really know a way to do the trick ?
Have you tried to dismantle the back-case? If you actually damaged the button inside the phone, I guess the only way is change the damaged part...
So I kinda new here and searched for similar threads with the same problems as i got , so far no success .
Heres all my story :
I have got HTC HD2 not long and I have installed NAND ROM Andriod on it ( it was installed from the SD card )
Phone worked great and evrything was nice till yesterday when my phone touch screen had stopped working so i decided to install the same OS ( Windows Mobile 6.5 ) that i recived it with , to exchange for new HD2
So i have tired to install WM6.5 , here what i have done :
I have downloaded this rom : World Wide English (WWE) 1.66.405.2
from here : http://forum.xda-developers.com/showthread.php?t=623283
I turend the phone off and opened the Bootloader screen , connected the USB cable and run the .exe rom file
It have finished installing and and phone turned off after that i pluged off the cable and tried to turn the phone on but it dont turn on at all even bootloader screen dont turn on , cant do anything with it
as i understood its briked now ? or its not?
looks like i forgot to ActiveSync before I started instaling the ROM
and now phone dont do anyhing at all
Here's what i had before i tried to install MW6.5 back :
In bootloader screen : PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
R 2.15.50.14
and also installed DFT MAGLDR Bootloader at the end
and then loaded some NAND ROM from the forum
So now my phone birked? if no is there any way to fix it?
Do i still got Garenty on it and i can exchange it ( as my touch screen is not working and now phone dont even start )
What should i do pelase help me
Is it a tmous hd2? (Red end key green send key) if yes then yes its bricked, the radio in that non-tmous stock rom killed it. JTAG or new mainboard needed.
If no, check the battery pins.
samsamuel said:
Is it a tmous hd2? (Red end key green send key) if yes then yes its bricked, the radio in that non-tmous stock rom killed it. JTAG or new mainboard needed.
If no, check the battery pins.
Click to expand...
Click to collapse
no its the normal HTC HD2 , buttons White designs T8585 HD2
forgot to tell somthing :
When i connected the phone to the pc i didn't ActiveSync ,
i just turend phone off then turn on bootloader and conencted via cable and turned on the exe file
and it started installing got to 100%
then said it completed succesfuly(in the computer) and phone turned off and since then it dont turn off or recat for cable connection or charging
also i conected the phone via USB cable to the PC then i pluged the battery and my Win7 tried to install some drivers ( it also treid to install them after it finished installing the rom )
A day have past
Please friends help me !!! :[
also i have noticed when i put the battery in and try to turn on bootloader
by presing Turn off button and Volume down
the phone makes some sound
but very small/minor vibtare or sortof
(only if i put my ear on the phone xD i can hear it)
please help me
HTC T8585
alb3553 said:
Please friends help me !!! :[
also i have noticed when i put the battery in and try to turn on bootloader
by presing Turn off button and Volume down
the phone makes some sound
but very small/minor vibtare or sortof
(only if i put my ear on the phone xD i can hear it)
please help me
HTC T8585
Click to expand...
Click to collapse
Is it able to do off-mode charging? if so, leave it to charge and then take battery out, put it back in and try going into bootloader mode again.
Moon2 said:
Is it able to do off-mode charging? if so, leave it to charge and then take battery out, put it back in and try going into bootloader mode again.
Click to expand...
Click to collapse
I dont see the red light as it need to be when it charging
but let me try im 99% sure bootloader wont satart
Hmmm, so its gotta be either a power issue, a random death,(hd2s are starting to age, and they've never been totally robust hardware wise) or a flash that went so wrong it fried the firmware totally.(I'm guessing without rereading your previous posts that the drivers the PC tries to find are "Qualcomm cdma blahblah" or something similar? Often seen when a phone needs a jtag)
Only suggestions I can offer are
Battery out, USB in and on wall charger, and then put battery in,
take a really good look at the battery pins,
perhaps take a voltmeter to the battery
try another battery, try your battery in another hd2,
alb3553 said:
I dont see the red light as it need to be when it charging
but let me try im 99% sure bootloader wont satart
Click to expand...
Click to collapse
Sorry to tell you that your phone is bricked :/ what I did is I just called T-Mobile and told them something weird happened to my phone and they sent a replacement to me lol
Sent from my GT-I8150 using XDA App