Hello
I have a HTC HD2
I wanted to install android onto it.
And so installed HSPL 3.0.300000 from the package HSPL 4.0
After that the phone booted.
I powered it off and installed magldr 1.13
(I know MAgldr only works o HSPL 2.08 but i came to know that afterwards)
Now, I can't even get to the bootloader splash screen.
Pushing power button and volume down does not do anything.
Please help
Thanks.
Try hit reset button and hold the volume down.
and follow how to downgrade HSPL , in section "A1:Install HSPL3" of this GUIDE.
hope it's help.
thamlim said:
and follow how to downgrade HSPL , in section "A1:Install HSPL3" of this GUIDE.
Click to expand...
Click to collapse
but don't forget the warning (since the OP hasnt said what version hd2 he has) that following those instructions on a tmous will brick it....
pulz said:
Hello
I have a HTC HD2
I wanted to install android onto it.
And so installed HSPL 3.0.300000 from the package HSPL 4.0
After that the phone booted.
I powered it off and installed magldr 1.13
(I know MAgldr only works o HSPL 2.08 but i came to know that afterwards)
Now, I can't even get to the bootloader splash screen.
Pushing power button and volume down does not do anything.
Please help
Thanks.
Click to expand...
Click to collapse
try to flash another radio.
good luck
Related
Hi guys. Thanks everyone for the wonderful work you all do.
Today I wanted to try for the first time to flash some NAND stuff.
I installed cLK, then I thought it would have been better MAGLDR so i tried to install it just after cLK.
After the installation, the phone just does not show the MAGLDR boot screen. It stucks at the HTC green logo (of course i keep the power button pressed). The previous working WM rom does not boot.
The only solution i found, is to flash again a wimo rom through ruu_update, from the bootloader (i have hspl4), then I can begin again but MAGLDR will anyway not install properly.
Do you have any suggestion? Thanks.
Sounds like yet another case of not having both spl 2.08.hspl AND an android compatible radio. (2.15.50 for example)
as comes up daily, magldr WILL NOT START without both those criteria filled. It will simply hang on the bootscreen.
thanks for the info.
I had Spl 3.03, I understood that MAGLDR would require 2.08 or above. Radio, is exactely the 2.15.50. What should i do now?
wrong, magldr requires 2.08.hspl ONLY. no other will work.
from magldr thread, post 1 line 4......
You need HardSPL 2.08 before installation!
Click to expand...
Click to collapse
Hi folks,
I tried to flash my HTC HD2 for the first time. Read /watched different guides. In first 2 steps they were all the same:
- install HSPL
- instal MAGLDR
Done both, got positive responses on both.
BUT: after rebooting after installing MAGLDR I do not manage to get the bootloader screen. There´s just a white screen with green htc logo on it and nothing else happens.
Yes, I held the power button after reboot; about 1 min long. Nothing.
If I hold volume down button after reboot the stripey screen appears like after the HSPL installation. But there is also no menu.
Also tried to proceeed task29 with the HD2 Android NAND Toolkit. Got positive response there too and after this I begann from scratch. With the same results.
Does anyone have a clue what I made wrong or forgot?
Or a hint what to do now?
best regards
M.
What version hspl n magldr?
Sent from my LG-P999 using XDA App
and radio,
hspl MUST be 2.08.hspl ONLY
radio MUST be 2.xx.50.xx
Got hspl version 2.08.hspl from http://forum.xda-developers.com/showthread.php?t=611433
got MAGLDR version 1.13 from http://forum.xda-developers.com/showthread.php?t=893618
cant remember the full radio version but I checked it before starting and it fits to requirements.
But I´m a few steps forward...
Meanwhile I flashed the newest Original HTC HD Win Mobile 6.5 ROM so phone boots up again
After that I installed HSPL version 2.08.0000 (now I know that was a failure) an tried again to install MAGLDR. But the progress bar doesn´t move - neither on PC nor on phone...
So I first will try to install again HSPL like samsamuel said and try again with MAGLDR
[EDIT]
Radio Version is now 2.15.50.14
SOLVED
Don´t know why but after dooing all step again (after falshing new HTC ROM) all ist ok and android is booting...
I think something was not in expected version on my old ROM on the phone. Never made an update before. So I recommend to do this before starting with all other
MiMo99 said:
Don´t know why but after dooing all step again (after flashing new HTC ROM) all ist ok and android is booting...
I think something was not in expected version on my old ROM on the phone. Never made an update before. So I recommend to do this before starting with all other
Click to expand...
Click to collapse
the only regular hd2 stock rom that includes a magldr compatible radio is 3.14, so if the ''old rom'' you flashed was any other version, it will have also flashed a non magldr radio, which is why it happened. (I suspect).
Sorted now,
the same problem
Hi,
I have the same problem.
Just white screen with green HTC mark.
But I'm not shure how to flesh win mobile again, because I cannot connect my HTC HD2 via USB (PC doesn't recognise the phone).
tnx
Hey MiMo,
Could you please post links and steps to help myself and anyone else looking on how to fix this?
by links I mean can I have the stock rom you used and the radios and such
Thank you.
Hi, I attempted to install Android on my GFs HD2. It was running Windows 6.5.
HSPL 2.08 was already installed and I installed MAGLDR 1.13. In MAGLDR I was able to select menu items but pressing the call-button didn't do anything. How do I unstuck myself? Help greatly appreciated.
UPDATE: I tried to flash the RUU_signed.nbh via SD from RUU_Leo_S_HTC_GER_3.14.407.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship but it failed, I guess. Now it won't boot (says Software Update failed, please try again). SPL 3.03.0000 is now installed. Slowly getting nervous over here. What's my way out of this mess now?
You should be ok to install hspl 2.08.
If you haven't already got it, get the HD2 nand toolkit (kusbedi) it makes things a lot easier. Then have a good read here.
OK, thanks, didn't know you could install HSPL from the bootloader too.
HSPL 2.08 is now installed. Still the same problem with MAGLDR not reacting to the call button, though. I guess I'll try CLK then.
You can just as easy install magldr again if you wish using the toolkit...
Hmm, I now formatted the memory with Task 29 and reinstalled MAGLDR, still no reaction to call-button presses.
I've got two hd2 s, and on both magldr never accepts the first press of send, I have to click it again slightly (only slightly,) firmer and fractionally longer. If I try the slightly longer firmer press first, it still doesn't accept it till the second press.
My point being to make sure its really a problem before you start re flashing.
If you assure yourself its really not accepting, try reflashing 2.08.hspl again but using hspl3, (there are occasional issues with Hspl4, not usually connected to magldr, but everything's worth trying) and then reflash magldr. The nand toolkit as advised is a good way to go.
Winmo roms, radios, hspl, task29... all can be flashed from bootloader, and indeed its a better way to flash.
grmpf... HSPL 2.08 from HSPL 3 was no help.
Now with cLK in Clockwork Mod, left button doesn't work either!! Points to a mechnical problem, but GF (owner) says no. Will keep trying.
polacco said:
grmpf... HSPL 2.08 from HSPL 3 was no help.
Now with cLK in Clockwork Mod, left button doesn't work either!! Points to a mechnical problem, but GF (owner) says no. Will keep trying.
Click to expand...
Click to collapse
Try installing a touch recovery? That will help you solve your problem. Also download a app like Quick Boot so you can boot straight into recovery from the Android OS.
T-Macgnolia said:
Try installing a touch recovery? That will help you solve your problem. Also download a app like Quick Boot so you can boot straight into recovery from the Android OS.
Click to expand...
Click to collapse
+`1
Thanks guys.
I successfully installed TWRP, the touch recovery built, and flashed NexusHD2-ICS-4.0.4-CM9-HWA V2.1 from there.
GF is going to be very happy!
Cheers
TWRP 2.0.0 thread
http://forum.xda-developers.com/showthread.php?t=1292146
TWRP 2.1.2 thread
http://forum.xda-developers.com/showthread.php?t=1647575
Hi Team
Just bought an old HD2 from work and am trying to flash to Android via the method described here - http://forum.xda-developers.com/showthread.php?t=1402975
I get as far as the repartition step 13, and when the phone reboots it does not load into CLK fastboot. All that happens is the white HTC screen comes up and doesn't go any further. At this point the phone is not detectable via ADB or normal USB.
The phone is a GSM HD2 and has HSPL 2.08 installed.
Any help recovering this or pushing forward with the flash is much appreciated.
At step 13 you are in recovery trying to install the rom, it should be trying to boot the rom!
If you are in recovery then you have clk installed.
You might not have the correct partition size for your rom, it will not boot if the partition size is too small.
.
shanman-2 said:
At step 13 you are in recovery trying to install the rom, it should be trying to boot the rom!
If you are in recovery then you have clk installed.
You might not have the correct partition size for your rom, it will not boot if the partition size is too small.
.
Click to expand...
Click to collapse
Yeah thats the problem - it goes through the CLK partition/recovery install, and the phone goes from the tricolour screen to the HTC 0-100% screen, reboots and then the white HTC logo screen. From the instructions, I thought the phone would go straight into CLK recovery.
Is there a set of key presses I'm meant to do to trigger recovery?
You have to hold "home" while booting to boot into recovery.
jianC said:
You have to hold "home" while booting to boot into recovery.
Click to expand...
Click to collapse
Thanks mate - will give this a crack when I get home
stuartgr said:
Thanks mate - will give this a crack when I get home
Click to expand...
Click to collapse
Yeah didn't work - still goes to the HTC logo...im guessing this means CLK didn't install properly.....Any other ideas?
Do you have install radio 2.15.50.14 ?
Sent from my NexusHD2 using Tapatalk
You have to give us more information.
What does it say when you hold down the volume button when starting the device ?
Same poblem
I have the exact same problem... The clk bootloader doesn't start up when i press the home button, after i've flashed it, but instead getting stuck on the HTC-white screen. I also have another HD2 where i can flash android(NAND) etc... without problems, so i can't really see why it doesn't work..
Right now i've been using:
- HTC HD2 EU-version
- Radio: have tried 2.14.50.02 and 2.15.50.14 without succes...
- SPL - 2.08
- HPSL 4
I'm using the HD2 toolkit when i'm trying to flash the phone.
Please help..
You need HSPL 2.08 or 3.03 to install clk.
Sent from the pub...
shanman-2 said:
You need HSPL 2.08 or 3.03 to install clk.
Sent from the pub...
Click to expand...
Click to collapse
Thanks for response.
I've already have HSPL 2.08, just checked it up to make sure...
It's really strange, that my phone does have the right radio and HSPL, but still hangning up on the white HTC bootscreen, after i've flashed clk into it.. or it says that it had "succesfully flashed it"...
My steps for installing magldr or clk, tried both now.
1: Wipe task 29.
2: Flash HSPL 2.08
3: Flash Radio 2.15.50.1
5: Flash clk.
6: Hardreset.
7: Holding down homebutton.
8: Stuck on white screen... -.-'
---
This is what i have on my tricolor-screen
PB81100 HC - BC
SPL - 2.08. HPSL 8G XE
0X05
CotullaHSPL 0x40
---
Is there any kind of solution for this and have this happen for anyone before?
Have you installed cwm recovery?
Thats what your trying to get to holding the home button.
If it's not working after installing recovery go here and go to post three and try installing clk 1.5 using the leoimg.nbh method.
edit: clk 1.5 comes with recovery pre-installed.
shanman-2 said:
Have you installed cwm recovery?
Thats what your trying to get to holding the home button.
If it's not working after installing recovery go here and go to post three and try installing clk 1.5 using the leoimg.nbh method.
edit: clk 1.5 comes with recovery pre-installed.
Click to expand...
Click to collapse
Thanks for response.
Just tried the sd leoimg.nbh method, but still getting stuck on HTC-white...
:crying:
two2tee said:
Thanks for response.
I've already have HSPL 2.08, just checked it up to make sure...
It's really strange, that my phone does have the right radio and HSPL, but still hangning up on the white HTC bootscreen, after i've flashed clk into it.. or it says that it had "succesfully flashed it"...
My steps for installing magldr or clk, tried both now.
1: Wipe task 29.
2: Flash HSPL 2.08
3: Flash Radio 2.15.50.1
5: Flash clk.
6: Hardreset.
7: Holding down homebutton.
8: Stuck on white screen... -.-'
---
This is what i have on my tricolor-screen
PB81100 HC - BC
SPL - 2.08. HPSL 8G XE
0X05
CotullaHSPL 0x40
---
Is there any kind of solution for this and have this happen for anyone before?
Click to expand...
Click to collapse
two2tee said:
Thanks for response.
Just tried the sd leoimg.nbh method, but still getting stuck on HTC-white...
:crying:
Click to expand...
Click to collapse
Hold the back button while powering on to get to clk, you can boot to recovery from there and then install rom...
If you get to clk don't forgrt to partition your nand through settings menu..resize partitions...
shanman-2 said:
Hold the back button while powering on to get to clk, you can boot to recovery from there and then install rom...
If you get to clk don't forgrt to partition your nand through settings menu..resize partitions...
Click to expand...
Click to collapse
Thanks for response, but it seems like it doesn't even boot clk.. Normally when you've flashed clk, the phone should reboot to a black screen with some text and from here you can flash cwm recovery. But in this case, the black screen doesn't even show up.
Could it be that my phone have some hardware faults, or maybe is my HD2 not compatible with the radio (2.15.50.14) which were recommended?
Anyway, is there some way to see if clk has been flashed properly, just to make sure that it's there?
two2tee said:
Thanks for response, but it seems like it doesn't even boot clk.. Normally when you've flashed clk, the phone should reboot to a black screen with some text and from here you can flash cwm recovery. But in this case, the black screen doesn't even show up.
Could it be that my phone have some hardware faults, or maybe is my HD2 not compatible with the radio (2.15.50.14) which were recommended?
Anyway, is there some way to see if clk has been flashed properly, just to make sure that it's there?
Click to expand...
Click to collapse
The radio is fine for all versions of hd2 and is what I have on my EU version. All I can say is to start from scratch ie. Install hspl 2.08, radio, task 29, then install clk 1.5 again.
In that order...
Sent from the pub...
shanman-2 said:
The radio is fine for all versions of hd2 and is what I have on my EU version. All I can say is to start from scratch ie. Install hspl 2.08, radio, task 29, then install clk 1.5 again.
In that order...
Sent from the pub...
Click to expand...
Click to collapse
Still doesn't solve the problem. I have tried with various kind of orders, but without luck.
Just made a recheck on everything and i can conclude that HSPL 2.08 and the radio 2.15.50.1 is there.
The problem may not be a wrong HSPL or radio, since it's there, but perhaps it might be the phone that doesn't flash clk proberly...
Im really confused right now
Anyway, i've also tried to install magdlr but still ended up on HTC-white screen -.-'
two2tee said:
Still doesn't solve the problem. I have tried with various kind of orders, but without luck.
Just made a recheck on everything and i can conclude that HSPL 2.08 and the radio 2.15.50.1 is there.
The problem may not be a wrong HSPL or radio, since it's there, but perhaps it might be the phone that doesn't flash clk proberly...
Im really confused right now
Anyway, i've also tried to install magdlr but still ended up on HTC-white screen -.-'
Click to expand...
Click to collapse
Really don,t know what to say, looks like a jtag...
shanman-2 said:
Really don,t know what to say, looks like a jtag...
Click to expand...
Click to collapse
Hmm i could flash a custom win6.5 rom without problem...Could that help us on our way or?
EDIT: Just to be more precise, i've used "Artemis HD2 v70.0"
Link:
http://forum.xda-developers.com/showthread.php?t=612580
Well if you can do that it's not a jtag.
Probably be better to go back to stock if all else fails.
Sent from the pub...
Hi, i ve read almost all topics here about the subject. this is what i've done so far:
i've succesfully installed
-hspl
-Radio Leo 2.15.50.14
-task29
-then MAGLDR111
then i was going to install an android nand version i found on the internet but my HTC got stuck on the green HTC logo screen.
i never get the bootloder menu. this is my problem.
Yes, I have leoimg.nbh in the root of my SD
After i put it there, i got an menu after reboot saying
'radio_v2
rcust
bootloader
splash1..'
press power to update...
but since this leoimg.nbh is my original windows image, it updates back to wm6.5
So anyone can help me how to pass this green screen please ?
try the links below, they might help
mengfei said:
try the links below, they might help
Click to expand...
Click to collapse
well it is just the shortcuts of what i've done already
i will probably wont be able to see the bootloader menu again..but thanks for the response
mmaniac said:
well it is just the shortcuts of what i've done already
i will probably wont be able to see the bootloader menu again..but thanks for the response
Click to expand...
Click to collapse
He says that to everyone, anyway.
First of all, not any HSPL will work. You need HSPL 2.08 for MAGLDR.
Second thing is, I suggest you use MAGLDR 1.13 (I still don't understand why people use the old, when there is a new)
Don't do Task29, it is useless. And now since you've installed winmo through sd card, you need to re-install HSPL (2.08), after that install MAGLDR (1.13).