Related
Have a nook color, cm7 - screen will not light. Power will cut on and off (i can tell because volume buttons produce noise when on). Screen gives no illumination when on.
Nothing software or programming updated or changed that would have caused it. I've charged it overnight and attempted to cut on while plugged in.
Plugged back into laptop via USB and I can see (nook color icon with yellow exclamation point) but still no screen.
I'm at a loss. Searched all posts but cannot find one similar. Thx!
I know that this happens and is fixable, although I cannot remember where I saw the "official" fix. If you have nandroid backups on a SD card, you could hard reboot the nook with the 8x reboot, and then reflash CWM and restore your backup.
Are you willing to lose your data and temporarily revert to stock?
I'll give anything a try.
Thanks for the idea. I'll try this in the morning and repost. I had thought about hard booting and taking it back but was worried they wouldn't replace it since it had been rooted. I'll go back and research the steps you mentioned. I'm not a techie so it will take a fresh mind and some coffee to pull it off. I was beginning to think it was a bad screen.
Power off nook, and power it back on. As soon as it begins to load, press n, power, and volume+ (I learned it with both volume keys, but I just heard it may only need the +) and hold for about ten seconds. The nook will flash off, release buttons. The nook will automatically restart, so after you release the keys, you want to repress them gain right as it starts to boot (where you would normally see the cyanogen logo). After the eigth time it will load into froyo firmware. If you. Misstime the sequence you will need Ronstadt over, so if it doesn't work the first time, just try again. Maybe a dark room, so you can see the slight illumination somewhat.
Bad screens do happen, I suppose, but the nook is unbrickable from a software standpoint. The primary boot is off the sdcard, so there is always a way to circumvent or preempt anything that may be corrupted internally. If you were to have a bad screen, after you hard reboot the nook, it will load the stock OS, but if you flashed CWM internally that will still be in your emmc. The way to get rid of the CWM is to follow the hard reboot with a factory reset through the froyo menu (standard nook OS for any future readers). If your screen is indeed bad, you can take your chances that they wont notice since they are replacing an obvious hardware issue, or you could hold it next to a working nook and base your touches approximately off that. There aren't that many steps, but you.do have to go through the B&N registration process, and your user name and password would be a *****.
I might just hard reboot and roll the dice myself, although I haven't personally heard of a bad screen yet. Good luck.
Solution worked!!
Thanks so much.....I couldn't get the 8x to work because the screen was not on and I couldn't time it right. The only way I could tell if it was on or off was with the power button making noises. So I held down power and N button together until flash. After the flash the cm7 open screen popped up. woot woot. and many thanks but I can only push the button once.
As suggested, starting a new thread.
Hello,
Straight to the point, Rooted UK Atrix, running 2.3.4. no other MOD OR rom or anything, i like motoblur.
Stupidly Used Bloatfreezer to freeze 'home' without having another launcher to return to. Can't use the phone now. Trying to reset (hard or soft i do not know the difference) and the phone reads ''fastboot'' then i toggle down using volume - to android recovery and the phone is coming up with starting rsd protocol x2 and nothing else (using the power + & - methods).
If i leave my phone to just boot it resides on a white screen teasing me with noises of logging in but i cannot see anything.
I'm really lost to be honest, i have no idea what to do and i am not good with terminology either (adw, flashboots, cm7 i have no idea what they are).
I know there are sooo many threads with different answer's so that is why i am starting a new thread.
To factory reset using recovery...
1.Power off the phone, press and hold volume down button, press power button.
2.Screen will come up with "Fastboot", press Vol down key to cycle through choices until you get "Android Recovery", press Vol up key
3.Wait for the "triangle ! / Android" screen then release the volume down button
*4.Tap on bottom right corner of the screen (may take a few times). a menu will come up
5.Tap on "wipe data/factory reset", and press OK. Another Confirmation screen will come. Press Yes and OK
6.After userdata is cleared, the "reboot system now" option will be highlighted by Default. Press OK.
7.Phone will reboot to initial setup MOTOBLUR screen.
NOTE/If on Android 2.3.4 then replace step #4 with pressing both Volume buttons at the same time. Also, use the Power button to activate the highlighted option instead of looking for the OK.
Sent from Rob's Atrix
atrixuk said:
As suggested, starting a new thread.
Hello,
Straight to the point, Rooted UK Atrix, running 2.3.4. no other MOD OR rom or anything, i like motoblur.
Stupidly Used Bloatfreezer to freeze 'home' without having another launcher to return to. Can't use the phone now. Trying to reset (hard or soft i do not know the difference) and the phone reads ''fastboot'' then i toggle down using volume - to android recovery and the phone is coming up with starting rsd protocol x2 and nothing else (using the power + & - methods).
If i leave my phone to just boot it resides on a white screen teasing me with noises of logging in but i cannot see anything.
I'm really lost to be honest, i have no idea what to do and i am not good with terminology either (adw, flashboots, cm7 i have no idea what they are).
I know there are sooo many threads with different answer's so that is why i am starting a new thread.
Click to expand...
Click to collapse
Can you get to android market via your computer? If so go to it, log in, find a launcher and install to your phone. Once rebooted to the phone, it *should* give you a choice or just automatically choose the new launcher. What does double tapping your home button bring you too? I was able to find my alternative launcher by moving around via that.
sounds like ya have frozen system files
prolly be easyest to unlock bootloader and push a custom rom to it (they work better than stock anyway
Yes i did freeze the home app.
I really mean thanks to those replied. Unfortunately i have tried the first suggestion but it doesn't let me get to step 3 with the triangle, fast boot - android recovery - can't fast boot 2 etc can't get passed that.
i have just plugged it in the Laptop, taking sim out, and it has started! i thought it was broken!! but unfortunately not 'home' yet...
SO it is at the motoblur login screen, should i log in? press factory reset? Any suggestions?
I'm not sure how to push an app straight to phone so i can install a launcher...
we're nearly there guys!
In addition to what Robkort said a few posts up ^^^ to get into the recovery on 2.3.4 you may have to scroll down once you see fastboot, until you see "Android Recovery" and press vol up - when the android dude comes up, if tapping the bottom right corner doesnt get you into recovery, press BOTH volume buttons at the same time.
It is now up and working with me just simply plugging it in, running moto sync, logging in to market from laptop and sending the launcher app..
Wifi was enabled luckily before i froze home, so when i pressed log in it went 'error' then launcher pro just popped up so now i think i just unfreeze home, turn it off, put my sim in and fingers crossed..
wish me luck!
Yahooooooooooooooooooooooooooooooooooooooooooooooooooooooooo!
It's worrying how much happier i am now that i am back on top with my phone working. Pretty dependant we become!
All my widgets, and motoblur have gone, and some writing is in a different language :/ universal inbox is not there either.
Still Thanks for all the suggestions!
I suggest this thread should be 'FROZEN' or just stay open if anyone ever freezes 'home' without having another launcher installed.
I'm glad i didn't need to flash anything, put other ROMS on, hard reset losing everything, solved pretty simple luckily.
Hello all, I'm curious to hear your thoughts and advice.
My nook is completely unresponsive. It is not stuck at rooted forever.
In fact this has nothing with a root attempt/reset/restore/power on.
I had done a a fresh reset/root with touchnooter about four months ago and was happily and smoothly reading for about two months. I then got busy and put the nook down, did not touch or use for about another two months. I tried to use it about a week ago but found that it had run out of battery in sleep after the two months of disuse (not surprising). I put it on charge overnight and everything booted right and functioned well once it turned on, except that the battery indicator in the statusbar showed a "?" and the battery info in system info showed 100% "unknown". After alot of fruitless research I put it down with the intention of reset/restore/root when I had the time.
I just picked it up this morning and was faced with the expected "Press then button below to wake up your NOOK" screen. But when I pressed the "n" button nothing happened. Obviously holding the "n" did nothing as well.
I tried to power it off and on- nothing
holding power for 20- nothing
power for 30- nothing
8 failed boots- nothing
left right- nothing
left right power-nothing
random pushing and holding of power- nothing
all these with mem card in and out- nothing
all these plugged usb- nothing
all these pugged ac- nothing
I let it charge some more- nothing
None of the buttons do anything, the screen stays inevitably at the " press the n button to wake" screen. no activity whatsoever except that when It is plugged in, the green light shows. NO ORANGE LIGHT... it is fully charged by both usb and ac.
It is not detected at all by windows anywhere.
In Linux- lsusb, bklid, and df -h yield nothing. My nook might as well be the invisible stupid ereader.
I did not drop it, sumbmerge it, perform magic around it... It has been sitting on a shelf doing nothing.
To repeat, the only thing my nook does is light up green when plugged.
It is unchangeably stuck on poe's face...
If this isn't true brick, I don't know what is.
I'm exhausted. Any ideas? I appreciate the help.
Best,
Thomas
i don't know. i just know my dog ate mine and i'm now in the market for a new screen, so if you don't get it working sell me the unit and get some money for yourself to purchase a new one =D
or you could google the disassembly instructions and try unplugging the battery, not very hard to do. could be of .. some help perhaps?
I would definitely take you up on your offer, but i'm still under warranty.
However, I would still like to have my original, and figure out what is going on and why it happened.
Ideas?
Thank you.
similar problem were solved
Hi! I might have read about similar problem solved on USB host mode here http://forum.xda-developers.com/showpost.php?p=23475998&postcount=131
That's it, thanks so much.
if it help
if it helps let them know in the tread that you had same problem. they are wondering whether it is due to host mode
[N2E]: After automatic update to 1.1, Nook Touch Screen absolutely DEAD--Nothing Work
THIS WAS A POST FROM ANOTHER SITE AS TO MY PROBLEM:
I was reading on my N2E last night. I put it down for about 30 minutes and when I came back it was displaying the default "Authors" screensaver (I had switched to the Nature photos) and asking to slide to unlock. I thought, "Oh, the new software update must have downloaded and installed. I'll check it out." To my shock, the touch screen was completely unresponsive--no amount of swiping would unlock from the screen saver. I let it set for a while longer thinking perhaps the softare update was not yet finished. No such luck.
As a result of the new update, my NOOK is now completly DEAD! I tried powering off, but couldn't do that because you are asked to confirm power off on the touchscreen, which no longer works. So, I looked online and tried the soft reset/reboot by holding down the "Home" or "n" button and then pressing the power button for several seconds. Great--it started rebooting...and came right back to the "authors" screen saver and asking to swipe to unlock. I tried this rebooting process several times, always with the same result: back to screeensaver mode with completely unresponsive touchscreen.
So, looked at the online technical troubleshooting discussion and helps and decided to try a downloaded manual install of the software update. Plugged my NOOK into my computer and it recognized it. So, I downloaded the manualo software update and dragged and dropped it onto the NOOK as directed and sure enough, it started to reboot itself. I thought, "whew, maybe this will fix it". NOPE--came right back to the locked screensaver, with no mention of attempting to update software, and the touchscreen is still dead. (By the way, all of this was done initially with the NOOK showing about 94% charged, so it was not a battery issue.)
Reconnected the NOOK to my computer and the software update file was gone from its home directory, which implies it did something with it. So, I tried repeatedly to install the software update manually, always with the same result: NOOK comes back to locked default "authors" screensaver wtih a dead touchscreen.
Looked online for B&N technical support again saw that others had this problem (though only found a couple references). Found the instructions to do a factory reset and reluctantly tried that, desparate to make my NOOK work again, but frustrated that if it did I would have to rebuild everyting on it and download my 400+ B&N book library all over again. But, guess what, factory reset just comes up to the "Welcome to your all-new NOOK" screen (sounds like progress), BUT the touchscreen is STILL dead, so I can't hit the "Next" button onscreen to proceed with setting up my factory-reset NOOK. Tried rebooting again (as this seems to be the only solution offered in the online tech support) and now it just keeps coming back to the "Welcome to your all-new NOOK" screen with a dead touchscreen keeping me from doing anything.
So, now I am taking it back to my local B&N store in hopes they will exchange it for a new NOOK.
I really want to see a feature to disable automatic updates in the future. I specifically didn't download and manually install when the update came out, figuring I'd wait for the automatic download to give time to B&N to work out the bugs and perhaps issue a patch (as they have done in the past for the N1E). Instead I get no warning about the automatic download (happens while I am reading and set the NOOK aside for 30 minutes), and then the update KILLS my NOOK.
I am not a satisfied NOOK customer at this point.
MY POST: (from the that site)
Not Sure how to do this post or whatever, but I was happy until the update and everything that happened to you is the same with me. This is the first post that describes what happened to me. I'm out of warranty and refuse (and can't) to buy another one of these. If their updates can do this, I'm not sure I want to sink another $100 into the shareholders pockets. I'd really like to know if anyone knows what may be wrong with it.
In addition to what was already mentioned, I took the battery out several times(which seems intimidating but very easy but voids the warranty) and took it completely apart cleaning the screen very well with water and another time a glass cleaner. I tried rooting also. Not sure of what to do now. It seems software related due to working fine until the update. Still at the "Welcome to your all-new NOOK" screen with unresponsive screen. I wasn't sure if the last sentence from B&N was a personal message to me welcoming me to the "new" state of the my nook.
Thanks for any help from anyone.
Thanks.
Identical problem.... and no fix..
It is a shame you got no solution for this. and the worst, you are not the only one... it happened exactly the same with my Nook ST....
Hopeless...
Machiavelli_The_Man said:
THIS WAS A POST FROM ANOTHER SITE AS TO MY PROBLEM:
I was reading on my N2E last night. I put it down for about 30 minutes and when I came back it was displaying the default "Authors" screensaver (I had switched to the Nature photos) and asking to slide to unlock. I thought, "Oh, the new software update must have downloaded and installed. I'll check it out." To my shock, the touch screen was completely unresponsive--no amount of swiping would unlock from the screen saver. I let it set for a while longer thinking perhaps the softare update was not yet finished. No such luck.
As a result of the new update, my NOOK is now completly DEAD! I tried powering off, but couldn't do that because you are asked to confirm power off on the touchscreen, which no longer works. So, I looked online and tried the soft reset/reboot by holding down the "Home" or "n" button and then pressing the power button for several seconds. Great--it started rebooting...and came right back to the "authors" screen saver and asking to swipe to unlock. I tried this rebooting process several times, always with the same result: back to screeensaver mode with completely unresponsive touchscreen.
So, looked at the online technical troubleshooting discussion and helps and decided to try a downloaded manual install of the software update. Plugged my NOOK into my computer and it recognized it. So, I downloaded the manualo software update and dragged and dropped it onto the NOOK as directed and sure enough, it started to reboot itself. I thought, "whew, maybe this will fix it". NOPE--came right back to the locked screensaver, with no mention of attempting to update software, and the touchscreen is still dead. (By the way, all of this was done initially with the NOOK showing about 94% charged, so it was not a battery issue.)
Reconnected the NOOK to my computer and the software update file was gone from its home directory, which implies it did something with it. So, I tried repeatedly to install the software update manually, always with the same result: NOOK comes back to locked default "authors" screensaver wtih a dead touchscreen.
Looked online for B&N technical support again saw that others had this problem (though only found a couple references). Found the instructions to do a factory reset and reluctantly tried that, desparate to make my NOOK work again, but frustrated that if it did I would have to rebuild everyting on it and download my 400+ B&N book library all over again. But, guess what, factory reset just comes up to the "Welcome to your all-new NOOK" screen (sounds like progress), BUT the touchscreen is STILL dead, so I can't hit the "Next" button onscreen to proceed with setting up my factory-reset NOOK. Tried rebooting again (as this seems to be the only solution offered in the online tech support) and now it just keeps coming back to the "Welcome to your all-new NOOK" screen with a dead touchscreen keeping me from doing anything.
So, now I am taking it back to my local B&N store in hopes they will exchange it for a new NOOK.
I really want to see a feature to disable automatic updates in the future. I specifically didn't download and manually install when the update came out, figuring I'd wait for the automatic download to give time to B&N to work out the bugs and perhaps issue a patch (as they have done in the past for the N1E). Instead I get no warning about the automatic download (happens while I am reading and set the NOOK aside for 30 minutes), and then the update KILLS my NOOK.
I am not a satisfied NOOK customer at this point.
MY POST: (from the that site)
Not Sure how to do this post or whatever, but I was happy until the update and everything that happened to you is the same with me. This is the first post that describes what happened to me. I'm out of warranty and refuse (and can't) to buy another one of these. If their updates can do this, I'm not sure I want to sink another $100 into the shareholders pockets. I'd really like to know if anyone knows what may be wrong with it.
In addition to what was already mentioned, I took the battery out several times(which seems intimidating but very easy but voids the warranty) and took it completely apart cleaning the screen very well with water and another time a glass cleaner. I tried rooting also. Not sure of what to do now. It seems software related due to working fine until the update. Still at the "Welcome to your all-new NOOK" screen with unresponsive screen. I wasn't sure if the last sentence from B&N was a personal message to me welcoming me to the "new" state of the my nook.
Thanks for any help from anyone.
Thanks.
Click to expand...
Click to collapse
The factory restore does not actually fix every possible problem with your Nook.
If your Nook responds at all, try to boot it up on an SD card like ClockworkMod or noogie.
At least that way you can see what is happening.
The partitioning might have become corrupted which the "factory restore" does not touch.
If no response with anything, try disconnecting the battery.
You might also try booting over USB using the techniques in rooting the new white glow.
Hello I was wondering if I'm just screwed I bought 2 nook simple touch, one for me and one for a present to my mother for her birthday on march 16. I bought them at best buy for $40 a piece on January 30. I used mine and was perfect but when I tried to set up my mom it wouldn't load the license agreement, always got stuck or reboot or something, so I loaded cwm on an sd card just to play around, tested on my nook and was fine, then put it on my moms nook booted once then I didn't press anything and turn it off then I load the image but when I tried to boot again it got stuck on the load screen and wont do anything, no reset sequence will work with the sd card on or off the other nook boots with this sd card. at the end I exchanged with my mom she is happy with her nook an I have a useless unit do you think they will exchange it I didn't rooted it or did anything to it but has the n cwm splash on screen forever. I'm in Costa Rica right now and wont return home until May do you think I'll might be able to exchange it or should I just try to repair it.
I'm glad that your mother got the working one!
You say that that one will boot on your CWM SD card, but yours won't?
It may be hard to get your unit exchanged with a conspicuous screen on it, even if it's not your fault.
When you plug it into your desktop is there any indication of a new USB device found?
If it's charged and no amount of the power button gets a reaction, I'd open it up.
any news???
Hi endor43, same problem here, have been able to find any solution?
endor43 said:
Hello all, I'm curious to hear your thoughts and advice.
My nook is completely unresponsive. It is not stuck at rooted forever.
In fact this has nothing with a root attempt/reset/restore/power on.
I had done a a fresh reset/root with touchnooter about four months ago and was happily and smoothly reading for about two months. I then got busy and put the nook down, did not touch or use for about another two months. I tried to use it about a week ago but found that it had run out of battery in sleep after the two months of disuse (not surprising). I put it on charge overnight and everything booted right and functioned well once it turned on, except that the battery indicator in the statusbar showed a "?" and the battery info in system info showed 100% "unknown". After alot of fruitless research I put it down with the intention of reset/restore/root when I had the time.
I just picked it up this morning and was faced with the expected "Press then button below to wake up your NOOK" screen. But when I pressed the "n" button nothing happened. Obviously holding the "n" did nothing as well.
I tried to power it off and on- nothing
holding power for 20- nothing
power for 30- nothing
8 failed boots- nothing
left right- nothing
left right power-nothing
random pushing and holding of power- nothing
all these with mem card in and out- nothing
all these plugged usb- nothing
all these pugged ac- nothing
I let it charge some more- nothing
None of the buttons do anything, the screen stays inevitably at the " press the n button to wake" screen. no activity whatsoever except that when It is plugged in, the green light shows. NO ORANGE LIGHT... it is fully charged by both usb and ac.
It is not detected at all by windows anywhere.
In Linux- lsusb, bklid, and df -h yield nothing. My nook might as well be the invisible stupid ereader.
I did not drop it, sumbmerge it, perform magic around it... It has been sitting on a shelf doing nothing.
To repeat, the only thing my nook does is light up green when plugged.
It is unchangeably stuck on poe's face...
If this isn't true brick, I don't know what is.
I'm exhausted. Any ideas? I appreciate the help.
Best,
Thomas
Click to expand...
Click to collapse
There are times when a Nook gets in a mode where it won't accept a charge.
Opening it up and disconnecting the battery for a minute might fix this.
endor43 said:
That's it, thanks so much.
Click to expand...
Click to collapse
When this worked for you did the light turn orange right when you plugged the battery back in? I just took the battery out, plugged the nook into a charger, and with it plugged in plugged the battery back in and the light stays green the whole time yet I'm not able to use the nook at all.
My nook second generation is not responding to my touch I tried everything to get it to work and I eventually got it to completely power of what if it does not work when I turn it on what should I do
It could be power/battery problems.
Check to see if it makes itself known when the USB is plugged in.
If it reacts at all, that's an indication of life.
Hi guys.
The other day I side-loaded some epubs for Grad Trip.
I went and in the middle of the trip I was going for my Nook, open the case and just see the half of the screen WIPED OUT:crying::crying::crying::crying:
I had no idea what was happening, i tried plugging it into my Mac, didn't work.
Researched like crazy for half an hour but found nothing.
So here I am to ask you guys for help..
My Mac won't even recognized my Nook Touch, and I'm FREAKING OUT
I'm guessing it's probably because of the .DS_Store and .Trashes folders...
What should I do?
Here's my MacBook Pro Specs:
Mid-2010 MacBook Pro
Intel Core i7, 15 inch, 2.66 Ghz
PLZ REPLY AND HELP ME!
I HAVE NO IDEA WHAT'S HAPPENING TO MY NOOK! (PANIC)
sorry... I tried to post an image but it didn't let me, i think the bottom would work... it's REALLY SERIOUS so please help!! (the ex) part is just there)
ex) goo.gl/SdBXZ
As annoying as the Apple tendency is to graffiti everything it can get its hands on with .DS_Store and .Trashes, I don't think that that is the problem.
Are you saying that the bottom half of the display doesn't change but the top half is fine and responds?
Can you do a normal full power and then reboot? Is it still the same?
I'd then suspect a hardware problem with the screen.
I don't know why you can't connect on USB.
That could be related or a red herring.
I'd probably try to do a factory restore and then get an in-warranty replacement.
Renate NST said:
I'd probably try to do a factory restore and then get an in-warranty replacement.
Click to expand...
Click to collapse
The following procedure details the process to Hard Reset your All-New NOOK. This process will deregister your device as well as erase all local content such as contacts, sideloaded documents, personal information, wishlists, 4 digit passcodes, etc. It is recommended you back up all wanted files to an SD card or computer. All Barnes & Noble content will be downloadable upon re-registering
1. Power off your NOOK by pressing and holding down the power button. When the “Do you want to power your device completely off” message appears, tap “Power Off.”
2. Once your NOOK has powered off, set it down on a clean level surface. Make sure that your NOOK's screen is facing up with the top of the device facing towards you.
3. Set your NOOK at the edge of the surface so you can access the power button.
4. Press and hold the Power button to power on your NOOK. When your device starts to power on, quickly let go of the power button then immediately press and hold the power button and both the bottom right and the bottom left page turn buttons together.
5. Continue to hold all 3 buttons for 5 seconds.
6. After 5 seconds, release the Power button; then release the side buttons.
7. Your device will show the ‘Read Forever’ screen then will present the Factory Reset dialog asking if you would like to perform a “Factory Reset,” Tap the "NOOK Home key" to confirm. Tap the "Home key" again to begin the process.
This is the only forum I can find to post this to.
Got out my old nook classic and wanted to remove a soft root I did a few years ago and I flashed the wrong firmware. I flashed 1.0 and it's a newer 1005 model. Now it's stuck on the "installing software update screen" and the LCD keeps looping.
Being that it's so old I'm having trouble finding out any info. Is there anything I can do? I can't get it to mount.
I assume you tried something like this? (from here)
This will actually restore it to the same exact way you got it from the store, brand new, including with the un-updated software assuming that there have been updates since you got it. It's the Nook equivalent of restoring your computer with a fresh format and new Windows/Mac/Linux installation.
Pop out your SDCard if you have one installed, again just to be safe.
Turn off your Nook by pressing the Power Button on the top of it.
With it off, showing you the blank white screen, press and hold the power button until the screen flickers black for a second, then continue to hold it for another 12 seconds. You won't see anything happen at this point, the screen will stay white.
Repeat the above step 6 more times in a row. Yep, you read that right, 6 more times in a row. My assumption is they do this so people don't accidentally restore their Nooks during normal use.
Now press the Power Button once to turn the Nook back on.
You'll see the touch screen go black, with a sky blue progress bar, and a description of what it's doing, such as mounting the drive, formatting, etc. This takes a few minutes so be patient.
Once it does that, it'll boot up to your main screen, (it can take a while) with any previous version of the software showing, and you'll need to treat it just as you did when it was brand spanking new. i.e. re-register it, set the display name again, reload your screensavers, books and so on.
To update to the latest software version, press the "My Library" button, and make sure you're in the "My B&N Library" area; tap the "Check for new B&N content" button, it'll re-discover that it needs to be updated to the latest software, and automatically go through that process again for you. It can and often does take some time, and do some reboots, partition mounting, etc., so just be patient and let it do it's thing.
1570 6336344
I have followed that and have had no luck. It just keeps looping.
I'm thinking it's dead...
"Dead" is it will not turn on. Yours is "confused"
Seems like what is needed is a method like NookManager or CWM in which the Nook 1 boots from the external SD card and then some repairs are pushed in.
There *is* seemingly such a method, detailed on the-ebook.org, but unless your Russian is up-to-date, you'll have to see if the Google translation is clear enough to give it a try. You don't have anything to lose and everything to gain at this point.
Search on this URL in Google and choose "Translate this page": http://www.the-ebook.org/forum/viewtopic.php?t=19536&sid=8c61d40bfbb40f6f5e3dfcfaa99e5545