Related
Does anyone know if it is safe to keep the charger cord attached while changing the battery? The goal, of course, is to prevent a hard reset. (Obviously, all data should be backed up to SD card first.)
Is there a post somewhere that outlines the recommended steps for the battery change? (Search has not yielded one.)
Thanks,
Steve G.
XDA on T-Mobile, GPRS
Hi, I recently replaced my battery with a higher capacity battery bought off ebay for $22US del from HK to UK in 5 days. search for ezipda, later bought one for an Ipaq for same price.
The process of changing over took 5 mins, BUT!! I would not recommend having it plugged in and changing batt. You may be shocked by the result (pun intended). I cant remember if it did a hard reset but dont think it did. As long as your back-up battery is charged and u are quick dont think there should be a problem.
Unscrew the screws and get a wide thin blade and go around the edge of the case, I didnt and caused a few marks ont he edges! There are a number of clips that pop open quite easily. The battery is held in place by double sided tape, use the the same blade and carefully prise the battery up. Replacement is a reverse of the procedure, the only tricky bit is the connector is quite small and a bit difficult to locate but not too bad.
Hope I have helped. :lol:
Thanks, BadgerBoy1.
The backup battery is the key, but how does one determine if it is working and charged? I've searched all over the system for an indicator of the backup battery, to no avail.
That begs the next question: If the backup battery is bad, where is it, and can it be replaced?
Before anyone jumps on me, I've been going through the Wiki and forums extensively, and found just one similar problem. Which wasn't solved...
My HTC TyTN/Hermes 200 won't boot up anymore. It is totally dead. I even can't get it into bootloader mode. Screen stays blank and the LED is off.
Put the (3 months old) battery in another Hermes to test it, and it's at 100% charge.
My Hermes shows a steady red LED when it's plugged into power without the battery in, and no LED at all when the battery is installed. The red LED turns off when the battery is installed while there's power going into the unit.
I've left the battery out for at least an hour, plugged it back in, same results. Like the other guy I tried the "pull power, pull battery, plug in power, plug in battery, reset" trick http://forum.xda-developers.com/show...6469&p=1077622 - to no avail.
Does anyone have any last resort ideas on how to get it to at least come back up to a boot loader screen ?
check the battery contact points on the phone. the hermes shows a red led when its plugged in but without a battery
... have you ever dismantled your hermes? your screen ribbon cable may have dead tracks or not be connected properly
just a test on the opposite side of the battery connectors with battery removed press firmly without putting pressure on the LCD, this worked for me when i had a white screen on power up.
if this fixes the problem you may need to actually dismantle the back and put some flame retardant electrical tape on the back over the existing tape to add an extra layer of pressure and retension
XtreMe_G said:
check the battery contact points on the phone. the hermes shows a red led when its plugged in but without a battery
Click to expand...
Click to collapse
Yes, I have cleaned the contact too, nothing. And the battery is OK for sure, my colleague's TyTN runs on it without any problem.
Mattnokis said:
... have you ever dismantled your hermes? your screen ribbon cable may have dead tracks or not be connected
Click to expand...
Click to collapse
In fact I have, I have totally dismantled and reassembled my TyTN yesterday afternoon, nothing.
the only other problem may be that when being dismantled you may have damaged some sensitive components, Electro Static Discharge will fry sensitive CMOS components, they do not like it at all, whenever dismantling you should wear an earth strap, any time i dismantled mine it was on a workbench with a static mat and i was earthed through the mat.
but this is one possibility, the only other idea is to swap main board and displays with another that works, finding someone willing to allow you to do this with a working hemes is the tough part.
thats as much all i can think of for now
R.I.P. my trustful Hermes 200
Thanks all for your assistance. I have come to the conclusion that my sweetheart is no longer among us. May she rest in peace.
I have obtained a (2d hand) replacement yesterday. May this one last longer.
I'll keep the old TyTN for replacement parts.
Oh well...
Hi everyone,
I sat down with my Nook in my back pocket today, and when I got up it was frozen on the startup screen, displaying "Nook by Barnes & Noble" and 5 dots with the first filled in. Since then the screen has not changed no matter what I do.
The device is responsive in two ways. Firstly, when plugged into a computer, the contents of the My Files and screensavers folders are visible and interactive. Secondly, when plugged into a computer or wall socket, the charging light comes on orange, and if the power button is held down for 10 seconds it turns green briefly, then goes back to orange. No change whatsoever is observed on the display, not so much as a flicker.
So, that being the case, any suggestions for fixing it? If the current display cannot be salvaged, is it worthwhile to try to buy a dead unit and Frankenstein a functional Nook? If so, how much could I expect to pay?
Thanks in advance!
New NSTs are currently going for £30 in the UK, so I'd put that at the top end of what to pay for a used one.
There's a 0.01% chance that the display connector needs to be reseated.
Open up your Nook and try reseating the connector.
Thanks! I'll go ahead and try reseating the display connector as soon as I can find a T5 screwdriver.
My Nook gets display frozen as well
My Nook Glowlight is in the exact situation as the OP.
I tried to reseat the connector to the screen on the mainboard by opening the rear case, no luck.
Any suggestions?
update: I replaced the mainboard with the one from my fathers, who has the same glowlight, it works. So it seems something is wrong on my own mainboard, not the whole main board though. Have no idea where to fix it.
I have a same issue with Nook Touch...its stuck half on "connect to charge" screen and only 25% display is working. Is there any guide on reseating the display connector?
Reseating the display connector is only a shot in the dark.
I don't think that that is the problem, but it would be stupid if it were.
There could be many things that cause the display to die.
Power circuitry is always suspect and the eInk uses higher voltages.
viny2cool said:
I have a same issue with Nook Touch...its stuck half on "connect to charge" screen and only 25% display is working. Is there any guide on reseating the display connector?
Click to expand...
Click to collapse
Did you solve it, i have the same issue.
I cannot turn on my LG G2 after putting a new battery in it that I bought of LG.
I have tried to hold the vol down and power button together will plugging into power source but to no avail.I have held just the power button while plugging into power but to no avail.
Any help would be much appreciated.
Try to carefully check the electric contacts: re-open the case and press enough all the electrical connectors. I solved this way...
There may also be a chance of damaged battery (it is hard to find an original one): in this case you have to ask for replacement.
MotoGix said:
Try to carefully check the electric contacts: re-open the case and press enough all the electrical connectors. I solved this way...
There may also be a chance of damaged battery (it is hard to find an original one): in this case you have to ask for replacement.
Click to expand...
Click to collapse
I have checked all the connectors umpteen times and they all click into place.
I got the battery from LG so it is a genuine LG battery has stated in my post.
I had same problem with my Optimus G
I change the battery last year with a battery I bought off Ebay without any problems.I then found out the battery was not genuine (not holding its charge) and I bought a battery from LG.When I replaced the battery I bought off Ebay with the battery I bought from LG my G2 would not turn on.
Is there a tool which I could use to test my G2 phone (download a tool/app)?
Could it be an hardware issue?
Shlong7 said:
I change the battery last year with a battery I bought off Ebay without any problems.I then found out the battery was not genuine (not holding its charge) and I bought a battery from LG.When I replaced the battery I bought off Ebay with the battery I bought from LG my G2 would not turn on.
Is there a tool which I could use to test my G2 phone (download a tool/app)?
Could it be an hardware issue?
Click to expand...
Click to collapse
I bought the battery on ebay, since I don't have access to any LG store.
After a first failed attempt, I removed and reinserted the battery and the phone turned on. I attributed the issue to an electric contact but my assumption could be wrong and there were likely other reasons...
Unfortunately, I am not able to suggest to you any workaround. You may ask directly to LG, where you bought the battery...
There is a hidden menu (3845#*802#) for testing battery and charge efficiency, but phone must be turned on, then you have to use the old battery.
Anyway, I don't think it is an hardware issue.
I bought another battery off eBay to see if it was the battery but the phone still won't turn on.
It sounds not good... Are some electrical contact pins of the phone possibly damaged or dirty?
MotoGix said:
It sounds not good... Are some electrical contact pins of the phone possibly damaged or dirty?
Click to expand...
Click to collapse
No,they look alright.
I did press the power button on the phone before I put the white camera cover on and the main white phone cover on.
So much the better!
What possible think could I have damaged?
Shlong7 said:
What possible think could I have damaged?
Click to expand...
Click to collapse
Sorry, I understood you solved the problem (misunderstanding due to my poor English).
Look carefully at all the pins of the connectors (screen, motherboard, etc.): Are they alright or bent over?
If they are bent over you can try to straighten them with an electronic nipper.
On the contrary, if they are OK, my advice is to go to the LG service center (for example where you bought the new original battery) and ask them to check the phone hardware. Perhaps it is just a stupid issue, easy to solve. It is still a great phone, even though it is 5 five years old, and it's worth it. It is even faster of my most recent Motorola X Play...
Unfortunately, I have not enough experience with this phone, so I can't help you anymore: I own it since few weeks only, because it is my wife old phone. I was just lucky in substituting battery with negligeble issues!
I have looked at all the pins on each connector and they look all in line.
May I have damaged the charging ribbons when I pressed the power button before I put the camera cover and the phone cover back on.
I have noticed the black tape on the camera cover (https://www.ebay.co.uk/itm/LG-G2-Ca...368363?hash=item2833f4ba6b:g:FWsAAOSwIaFZFH5k) is damaged,could this cause my G2 to not turn on?
Shlong7 said:
I have looked at all the pins on each connector and the look all in line.
May I have damaged the charging ribbons when I pressed the power button before I put the camera cover and the phone cover back on.
I have noticed the black tape on the camera cover (https://www.ebay.co.uk/itm/LG-G2-Ca...68363?hash=item2833f4ba6b:g:FWsAAOSwIaFZFH5k) is damaged,could this cause my G" to not turn on?
Click to expand...
Click to collapse
I don't think so: the power button acts on a switch; you can press on the switch in many other ways, with the same results...
Check instead the electric contact on the camera cover (see 2nd image of the camera cover, top-left of the above link): it is a sort of electrical bridge (closes the circuit). You may verify if it works right by means of a multimeter (null resistance).
MotoGix said:
I don't think so: the power button acts on a switch; you can press on the switch in many other ways, with the same results...
Check instead the electric contact on the camera cover (see 2nd image of the camera cover, top-left of the above link): it is a sort of electrical bridge (closes the circuit). You may verify if it works right by means of a multimeter (null resistance).
Click to expand...
Click to collapse
Im not good at using multi-meters.
What should I set the range of the multi-meter when testing the electrical bridge on the camera cover?
What should the multi-meter read when testing the electrical bridge to see if it works?
You should simply get zero resistance. Multimeters are easy to use: at first, select to measure resistance, by setting the highest sensitivity (the smallest full-scale), then measure the resistance. There are many tutorial on YouTube.
Please, consider it is possible this is not the problem!
Anyway, I'd suggest you warmly to send the phone at the service centre.
Sent from my LG-D802 using XDA Labs
Yes,I do get zero resistance when testing the electrical bridge on the camera cover.
It will cost alot to have it repaired at the service centre,probably not worth having my G2 repaired bc the battery cost me £40.
You're right, it might not be worth it.
Before throwing away the phone, try to ask where you bought the battery. Perhaps they will find a solution for you.
Another phone with similar specs costs more than 300£, for sure; moreover, most of phones have the cover in glass or alluminium and are more delicate than G2...
Sent from my LG-D802 using XDA Labs
I have been in touch with LG where I bought the battery from and they said the repair would cost more than I paid for the phone,which I predicted.
I don't think the battery is faulty (I bought another battery of eBay and the phone still won't turn on),unless the eBay battery is faulty too.
Could I have damaged the power switch if I pulled out the power switch connector while the battery was connected?
I am so sorry.
But, just for curiosity, what is the damage?
I just replaced the battery and screen on my LeEco Le Max 2, and this post will detail the process. Hopefully it will be helpful for someone who is considering to replace their screen and/or battery.
Consider buying an extra screen
There are a number of people who have reported breaking their screen as a result of replacing the battery. I highly recommend that you buy a replacement screen if you intend to replace the battery. Unfortunately while removing my screen I also created a few dead pixels (which you'll see later). With all that being said, it is definitely possible to remove your screen without damaging it. I suspect that next time I will be able to remove the screen without damaging it.
Tools required
- small philips screwdriver (from Jeweler's kit)
- thin prying tools
- suction cup that tightly grips screen (you'll see the one I used later)
- heat gun or hair dryer
Onto the replacement procedure
Before you begin, make sure that you have plenty of time to commit to the replacement. It took me about 2 hours to swap the battery and screen. You should also read this full post before attempting to remove your battery.
Remove any sim cards in your phone and turn your phone off.
You'll need to heat up the perimeter of the screen on your phone. This can be done using a heat gun, however I manged this using a hair dryer. I spent about 10 minutes heating up the screen before attempting to remove the screen. Note that as you're removing the screen you may need reheat certain areas of the screen to loosen up the adhesive that secures the screen.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Next you'll want to apply the suction cup towards the bottom of the screen. Ensure that you have a solid grip on the screen.
I pulled the suction cup away from the screen, and began to notice that the sides of the screen were begging to come undone. I used a prying tool to sliced the adhesive that was holding the screen in place.
Go around the edge of the screen very carefully until the entire screen is removed. Remember the screen is glass and will break if it's flexed too much. My advice would be to go slow and use a lot of heat.
You'll need to remove two small screws behind the screen in order to disconnect the cable which connects the screen to the body of the phone.
Then disconnect the screen ribbon from the phone.
There will be an additional 15 screws which you'll need to remove in order to get to the battery. If you are just replacing the screen you can skip ahead to the section where I connect the new screen to the phone.
With all of the screws removed, you can pry the shield away from the back of the phone. You'll need to be careful, as a ribbon is glued to the back of the shield.
You can see the glue locations for the ribbon on the back of the shield. With the shield removed, you can now finally access the old battery.
Disconnect the ribbon that is right above the battery. Near this large ribbon will be another smaller ribbon that connects the battery to your phone. Disconnect the battery from the phone.
Now you can begin to remove the battery.
Important note from an XDA user
Jaki1122 said:
In the attach photos, you can see on the glue band (or whatever is called) a wider zone close to the motherboard. That is because you are supposed to grab that and pull straight. Then the glue comes off and the battery pops off nicely without being bend and with 0 danger. For this procedure you need to take out the motherboard entirely, which is pretty easy and quick. Take out the SIM tray (I always forget about this one ), disconnect the few connectors (vol and power buttons, fingerprint, USB Dock and the coaxial cable on the right), then 2 screws and its just comes out. After this the end of the glue band is clearly visible and easy to take and pull. Also, and this applies to all phones, you can use isopropyl 99% to weaken the glue (also useful for cleaning PCBs and fix water damage). Another note: you should always avoid bending a Lithium battery like in the photos, heat it to 70 degrees Celsius to weaken the glue and take it out as straight as possible.
Note 2: FOR LE ECO LE 2 USERS: The battery is mounted exactly like the Max 2, BUT you need to take out the USB PCB and speaker on the lower part of the phone instead of the motherboard, given that there is where the "puller" is. Why is it different to the Max 2 if the rest of the phone is identical? No idea... Maybe a brainfart?
Click to expand...
Click to collapse
Be very careful not to puncture the battery as you remove the battery. The battery is glued into the base of the phone. You can see the two major glue strips in the following picture.
Place and secure the replacement battery.
Reassemble your phone. Before you put the new screen on, I recommend testing the original screen to see if you damaged the screen during the process.
You can see a few new dead pixels on my original screen. This happened as I was prying the screen open, so you'll want to be very careful as you remove the screen. Do not stick your prying tool too far in or against the screen. This damage is something I could live with, however since I have a new screen I'll go ahead and put it on. Turn your phone off before attaching a different screen.
You'll want to connect and test the new screen before proceeding.
Hopefully your new screen is working. Turn your phone off again. Now you should do your best to remove the old adhesive that was used to secure the old screen to the phone. However, you should only do this if you have new adhesive to secure the screen in place!
Your new screen should come with an adhesive template. Remove the outer edge of this template which will be placed on your phone's body.
Now place the adhesive template onto the body of the phone. You'll have to push down such that the adhesive has been firmly placed. Remove the template such that only the adhesive around the perimeter of your phone remains.
Connect the new screen's ribbon to the phone, and secure with the two screws. You can now firmly place the new screen into the phone. You'll want to firmly press the screen into place around the edges.
You'll want to keep pressure on the screen while the adhesive sets in place. I used a few pennies placed on the floor to give clearance to the rear camera. Then I placed the phone on the pennies, and heated up the screen again. I believe the adhesive will cure faster and stronger onces it's been warmed up.
I then placed a textbook onto the screen with a 10 pound weight, where I let the phone sit for an hour or so.
Enjoy your newly replaced battery/screen and hopefully this has been helpful!
AccuBattery stats for the new battery
I'm now on the second charge of the battery, and I figured you may be interested in some of the stats of the battery. You can see that despite the battery being labeled 4100 mAH, the estimated battery capacity is only about 3000 mAH.
Frequently Asked Questions
coming soon
Edit June 7, 2019, I think we can conclude that changing the battery capacity as detailed below doesn't do anything
Updating battery capacity in Lineage based roms
This is in regards to this post https://forum.xda-developers.com/galaxy-s3/general/fix-compiled-powerprofile-xml-file-to-t1732722
I don't think that updating the power_profile.xml https://github.com/LineageOS/androi...works/base/core/res/res/xml/power_profile.xml does anything really. However if you want to change it to a new battery capacity, this post will explain how.
I edited the default power_profile.xml to reflect the new 4100 mAH battery (there are many doubts of the real battery capacity). I then compiled the power_profile.xml. The attached power_profile.xml is the compiled version.
1. Boot into recovery and copy /system/framework/framework-res.apk over to your computer.
2. Make a backup of this framework-res.apk
3. Open framework-res.apk on your computer using 7zip.
4. Navigate to res/xml/
5. Delete the power_profile.xml
6. Copy the attached power_profile.xml into the location where the previous power_profile.xml file was. Note this is a compiled file, meaning that it is not in plain text and you can't read the inside of the file.
7. save the framework-res.apk
8. Copy the new framework-res.apk over to /system/framework/
9. Reboot your phone.
You can use the following command to pull a csv of your battery stats while your phone is connected to your computer and running lineage (other other OS). More info here https://developer.android.com/studio/command-line/dumpsys
Code:
adb shell dumpsys batterystats --checkin > bat.csv
which will create a comma separated list of your battery properties. The one related to the specified capacity of your battery has the section identifier pws. Open bat.csv on your computer and search for pws. Before doing this change it would show up as 3100, and now it shows up as 4100. However, I have not noticed that this did anything different with the battery behavior or estimated battery capacity. The only thing this appeared to do is now that when I open AccuBattery a different manufacture capacity shows up.
Six month battery review:
I have 120 charge sessions, and probably only 1% of those used Quick Charge 3.0. AccuBattery shows estimated capacity of 3,065 mAh. The battery has been strong so far. See attached screenshots.
Hi, great guide, but when i try to download the power_profile.xml you uploaded i get an error.
I'm thinking on buying a new battery to replace it (and buy a screen just in case) because my current one its not calibrated and i cannot find a way to calibrate it, it says that its got 1800mah but it can actually hold 3000+.., the real capacity its really 3000-? i have seen people that say its around 3800~ can you confirm?
Links to buy???
sameer 100 said:
Links to buy???
Click to expand...
Click to collapse
These are the products that I purchased and the price that I paid. I don't necessary endorse these products... besides the suction cup. That one was great. One more thing, the adaptive brightness on the new screen doesn't appear to work as good it with the original screen.
Screen $13.17: https://www.aliexpress.com/item/ori...-X820-touch-screen-Digitizer/32862597681.html
Battery $10.81: https://www.aliexpress.com/item/HSA...-2-X820-Le-Max2-5-7inch-X821/32875310678.html
Tools $11.88: https://www.aliexpress.com/item/Jel...Set-LCD-Screen-Opening-Plier/32831437976.html
Suction cup $1.36: https://www.aliexpress.com/item/Bod...ss-Metal-Cell-Phone-Table-PC/32843015681.html
hitagisenjougahara said:
Hi, great guide, but when i try to download the power_profile.xml you uploaded i get an error.
I'm thinking on buying a new battery to replace it (and buy a screen just in case) because my current one its not calibrated and i cannot find a way to calibrate it, it says that its got 1800mah but it can actually hold 3000+.., the real capacity its really 3000-? i have seen people that say its around 3800~ can you confirm?
Click to expand...
Click to collapse
Try right clicking power_profile.xml and doing a save as. That just worked for me.
If it's a software bug, then EUI should help.
I was in a similar situation where my phone was 1.5 years old, and my estimated battery capacity was around 1700 mAH. I tried calibrating my battery (on lineage), and it did not work. As soon as I put this battery in, on the very first charge, the calibration appeared correctly on lineage. No sudden battery % drops or other weird behavior.
xlcashlx said:
These are the products that I purchased and the price that I paid. I don't necessary endorse these products... besides the suction cup. That one was great. One more thing, the adaptive brightness on the new screen doesn't appear to work as good it with the original screen.
Screen $13.17: https://www.aliexpress.com/item/ori...-X820-touch-screen-Digitizer/32862597681.html
Battery $10.81: https://www.aliexpress.com/item/HSA...-2-X820-Le-Max2-5-7inch-X821/32875310678.html
Tools $11.88: https://www.aliexpress.com/item/Jel...Set-LCD-Screen-Opening-Plier/32831437976.html
Suction cup $1.36: https://www.aliexpress.com/item/Bod...ss-Metal-Cell-Phone-Table-PC/32843015681.html
Try right clicking power_profile.xml and doing a save as. That just worked for me.
If it's a software bug, then EUI should help.
I was in a similar situation where my phone was 1.5 years old, and my estimated battery capacity was around 1700 mAH. I tried calibrating my battery (on lineage), and it did not work. As soon as I put this battery in, on the very first charge, the calibration appeared correctly on lineage. No sudden battery % drops or other weird behavior.
Click to expand...
Click to collapse
Did you fixed that problem? Or your battery was actually 1700mah? Because mine is not..
Also any updates in the real battery capacity? I've thinking on changing the battery right away, but if its only 3000mah its not worth, whats the charge current when it reaches 100%? it should say that in accubattery
hitagisenjougahara said:
Did you fixed that problem? Or your battery was actually 1700mah? Because mine is not..
Also any updates in the real battery capacity? I've thinking on changing the battery right away, but if its only 3000mah its not worth, whats the charge current when it reaches 100%? it should say that in accubattery
Click to expand...
Click to collapse
My battery was failing and rapidly getting worse. The capacity I was getting was actually 1700 mAH.
You can see the current hit zero and the capacity is still around 3100 mAH. I did a 1% to 99% uninterrupted charge in EUI. It would have been nice if the battery was actually 4100 mAH, but it does not appear that is the case.
xlcashlx said:
My battery was failing and rapidly getting worse. The capacity I was getting was actually 1700 mAH and was rapidly getting worse.
You can see the current hit zero and the capacity is still around 3100 mAH. I did a 1% to 99% uninterrupted charge in EUI. It would have been nice if the battery was actually 4100 mAH, but it does not appear that is the case.
Click to expand...
Click to collapse
Feelsbad, well its better than 1700 anyways, thanks for sharing
Hi bro, i heard from a guy that has recently replaced the battery to this HSABAT one that all OREO & Nougat roms are capped at 3100mah and you need to use another rom (this: https://t.me/LeitaEUI6) to get the full capacity of the battery, he says its real battery capacity its around 3800~ mah, will be cool if you try this rom and share results
hitagisenjougahara said:
Hi bro, i heard from a guy that has recently replaced the battery to this HSABAT one that all OREO & Nougat roms are capped at 3100mah and you need to use another rom (this: https://t.me/LeitaEUI6) to get the full capacity of the battery, he says its real battery capacity its around 3800~ mah, will be cool if you try this rom and share results
Click to expand...
Click to collapse
That would be cool.
Can I use any EUI6 build? I did try EUI5 and the capacity was still arround 3100 =/
xlcashlx said:
That would be cool.
Can I use any EUI6 build? I did try EUI5 and the capacity was still arround 3100 =/
Click to expand...
Click to collapse
I dont know, try the one i sent
Hey,
fist, thanks for that great guide!
I also changed my battery, but the capacity is only 3000 mAh. It is better than the old battery, but not 4100 mAh. I did the thing with the xml file. But nothing changed. I have lineageos pie.
I think there are more mechanisms which will decrease the capacity.
I think it will be the battery_cycles. If the cycles are high, the batteryvoltage will be cut. If I charge, the battery isn't at 4.4 volts.
I found this files to change the cycles and the capacity. But it is just temporary:
/sys/Classic/power-supply/battery/
If I write in these files, at the next start it will be changed...
Is there any solution for the shutoff voltage and charge voltage?
Thanks.
Excellent work!
This phone is mercifully reparable once the screen is off. My advice to people is to take that part very carefully and deliberately, it's about the only thing you'll break if you're careless. Once it's off, things become much easier.
Publishing information like this is very helpful to those who would attempt repairs of a solid phone, and it's a gift to the community.
Did someone remove the screen without breaking it? Maybe with a small peace of plastic sheet instead metal prying tool .
Huncriter said:
Did someone remove the screen without breaking it? Maybe with a small peace of plastic sheet instead metal prying tool .
Click to expand...
Click to collapse
Those few dead pixels were the only damage to my screen, and it's damage I could have lived with. After this experience, I probably could have removed the screen without damage. This was the first smartphone with this design that I've ever opened.
I think this YT video shows someone removing a Le 2 screen without breaking it. https://www.youtube.com/watch?v=f_LExkf89z0 Be warned the fingernail thing you'll see grosses me out.
That said, there are numerous comments on XDA about people breaking their screen while attempting to replace their battery. It's highly recommended that you buy a replacement screen, especially if the lead (shipping + order) time is long for your country.
Thanks
Ths
Important extra info on the repair!!!
I've changed countless screens on this (and other) phones, and there is something VERY important missing on this tutorial (very well done apart from what I'm about to explain).
In the attach photos, (the same as in the OP post) you can see on the glue band (or whatever is called) a wider zone close to the motherboard. That is because you are supposed to grab that and pull straight. Then the glue comes off and the battery pops off nicely without being bend and with 0 danger. For this procedure you need to take out the motherboard entirely, which is pretty easy and quick. Take out the SIM tray (I always forget about this one ), disconnect the few connectors (vol and power buttons, fingerprint, USB Dock and the coaxial cable on the right), then 2 screws and its just comes out. After this the end of the glue band is clearly visible and easy to take and pull. Also, and this applies to all phones, you can use isopropyl 99% to weaken the glue (also useful for cleaning PCBs and fix water damage). Another note: you should always avoid bending a Lithium battery like in the photos, heat it to 70 degrees Celsius to weaken the glue and take it out as straight as possible.
Just as a note, I'm just trying to help here, not criticising other people's very appreciated apportions, just complementing them when I can.
Note 2: FOR LE ECO LE 2 USERS: The battery is mounted exactly like the Max 2, BUT you need to take out the USB PCB and speaker on the lower part of the phone instead of the motherboard, given that there is where the "puller" is. Why is it different to the Max 2 if the rest of the phone is identical? No idea... Maybe a brainfart?
3000 mAh to 4100 mAh
xlcashlx said:
I just replaced the battery and screen on my LeEco Le Max 2, and this post will detail the process. Hopefully it will be helpful for someone who is considering to replace their screen and/or battery.
Consider buying an extra screen
There are a number of people who have reported breaking their screen as a result of replacing the battery. I highly recommend that you buy a replacement screen if you intend to replace the battery. Unfortunately while removing my screen I also created a few dead pixels (which you'll see later). With all that being said, it is definitely possible to remove your screen without damaging it. I suspect that next time I will be able to remove the screen without damaging it.
Tools required
- small philips screwdriver (from Jeweler's kit)
- thin prying tools
- suction cup that tightly grips screen (you'll see the one I used later)
- heat gun or hair dryer
Onto the replacement procedure
Before you begin, make sure that you have plenty of time to commit to the replacement. It took me about 2 hours to swap the battery and screen. You should also read this full post before attempting to remove your battery.
Remove any sim cards in your phone and turn your phone off.
You'll need to heat up the perimeter of the screen on your phone. This can be done using a heat gun, however I manged this using a hair dryer. I spent about 10 minutes heating up the screen before attempting to remove the screen. Note that as you're removing the screen you may need reheat certain areas of the screen to loosen up the adhesive that secures the screen.
Next you'll want to apply the suction cup towards the bottom of the screen. Ensure that you have a solid grip on the screen.
I pulled the suction cup away from the screen, and began to notice that the sides of the screen were begging to come undone. I used a prying tool to sliced the adhesive that was holding the screen in place.
Go around the edge of the screen very carefully until the entire screen is removed. Remember the screen is glass and will break if it's flexed too much. My advice would be to go slow and use a lot of heat.
You'll need to remove two small screws behind the screen in order to disconnect the cable which connects the screen to the body of the phone.
Then disconnect the screen ribbon from the phone.
There will be an additional 15 screws which you'll need to remove in order to get to the battery. If you are just replacing the screen you can skip ahead to the section where I connect the new screen to the phone.
With all of the screws removed, you can pry the shield away from the back of the phone. You'll need to be careful, as a ribbon is glued to the back of the shield.
You can see the glue locations for the ribbon on the back of the shield. With the shield removed, you can now finally access the old battery.
Disconnect the ribbon that is right above the battery. Near this large ribbon will be another smaller ribbon that connects the battery to your phone. Disconnect the battery from the phone.
Now you can begin to remove the battery.
Important note from an XDA user
Be very careful not to puncture the battery as you remove the battery. The battery is glued into the base of the phone. You can see the two major glue strips in the following picture.
Place and secure the replacement battery.
Reassemble your phone. Before you put the new screen on, I recommend testing the original screen to see if you damaged the screen during the process.
You can see a few new dead pixels on my original screen. This happened as I was prying the screen open, so you'll want to be very careful as you remove the screen. Do not stick your prying tool too far in or against the screen. This damage is something I could live with, however since I have a new screen I'll go ahead and put it on. Turn your phone off before attaching a different screen.
You'll want to connect and test the new screen before proceeding.
Hopefully your new screen is working. Turn your phone off again. Now you should do your best to remove the old adhesive that was used to secure the old screen to the phone. However, you should only do this if you have new adhesive to secure the screen in place!
Your new screen should come with an adhesive template. Remove the outer edge of this template which will be placed on your phone's body.
Now place the adhesive template onto the body of the phone. You'll have to push down such that the adhesive has been firmly placed. Remove the template such that only the adhesive around the perimeter of your phone remains.
Connect the new screen's ribbon to the phone, and secure with the two screws. You can now firmly place the new screen into the phone. You'll want to firmly press the screen into place around the edges.
You'll want to keep pressure on the screen while the adhesive sets in place. I used a few pennies placed on the floor to give clearance to the rear camera. Then I placed the phone on the pennies, and heated up the screen again. I believe the adhesive will cure faster and stronger onces it's been warmed up.
I then placed a textbook onto the screen with a 10 pound weight, where I let the phone sit for an hour or so.
Enjoy your newly replaced battery/screen and hopefully this has been helpful!
AccuBattery stats for the new battery
I'm now on the second charge of the battery, and I figured you may be interested in some of the stats of the battery. You can see that despite the battery being labeled 4100 mAH, the estimated battery capacity is only about 3000 mAH.
Click to expand...
Click to collapse
Can I install 4100mAh battery to my le2? 3000 is not enough
Are you kidding ? You unnecessary quote an entire post asking a question you could have answered yourself just by reading the thread ? Unbelievable.