Hi everybody!
I flashed WP7 for my HD2, but when installed, the fist time boot up HD2 only runs to gogogo is to restart itself. I removed the battery for about 5 minutes and restarted the WP7 again, but it's only runs about 15 minutes to restart itself and repeat the above error.
Any help?
Task29-Format Your SD Card -Install WM -Install Magldr-Do Two Wipe-Install WP7 Rom
Have Fun
Thanks for your reply.
I did as your guide, But the HD2 still fails as above
so did it work on WM (6.5) ok or not.
You must be missing a step somewhere
ahhynt branch
It Ok, I flashed WM 6.5 or Android, It work OK.
me too
Me too.
Please tell me when slove it,thanks.
so the first thing that comes to mind assuming you have had Android and WM6.5 working is the SD card.
The big difference is that WP7 needs a good working SD card in order to operate.
At the first install and boot it needs to see a clean formatted card ( FAT 32) or wont work.
Also directly after your WP 7 flash you have to hard reset the phone !!!
Are you sure you have the correct HSPL
Are you sure you have flashed the correct radio for the rom you are trying to flash.
Good luck
Hi!
I have replaced another memory card and flash the WP7, but it boot is very difficult, stop and reboot it in "go go go", I must remove the battery then re-start, and it runs very well. What's must I do?
check to Make sure your battery contacts are making proper contact with battery.
alphaacres said:
check to Make sure your battery contacts are making proper contact with battery.
Click to expand...
Click to collapse
I don't undestand????
KCTV 123 said:
I don't undestand????
Click to expand...
Click to collapse
battery??? you don't need to install wm6.5 everytime you want install wp7. just task29...install magdlr...perform the necessary magdlr prep steps (10-services, 5-clear mbr, 4-uselast24nand)..then flash wp7.
also, if your sd was not usable...it would have at least booted and told you the sd was bad. but make sure you do the magdlr prep steps before flashing wp7.
as for the battery, he's saying that sometimes the middle battery contact has a tendency to be out of place...check your contacts are all in correct position.
Related
All,
I try to make it as brief as possible.
this is what i post on the winmo section :
Dear All,
I try to make it short:
1. from winmo migrated to android
2. HSPL-ed 2.08
3. ran task29
4. installed barebone energy rom
5. clrd and haret. use mdeejay froyo android rom.
6. not satisfied with PPP and camera
7. wanna change back to winmo
8. CANNOT ENTER BOOTLOADER
9. pull out sd card, battery and sim card for 15 mins
10. hold -vol, successfully entered BOOTLOADER
11. have to repeat same procedure "pull out sd card, baterry and sim card for 15 mins" in order to enter booatloader
12. try enter bootloader from activesync, failed! have to pull out everything for 15mins in order to enter bootloader.
why is it happen "that" way? is it because of android (haret? or clrd?)? how to get back my normal way of entering bootloader without pulling out everything for 15mins?...
thanks
Amir
Click to expand...
Click to collapse
Now:
My battery drained even faster, 15% per hour
my idle process used 100% at all time
i cant "normally" enter bootloader anymore. see above quote.
i cant run Android anymore. i used to run on Android before. i took all action required provided in this forum. but still didnt success.
when running Haret, my screen stuck at green HTC logo and black background. i left it for night long, but still stuck.
i reformat sd card, not quick format, format thru pc and hp, still no luck
what should i do now?
Hope this helped
So let me summerize your probs,
1-Bootloader can't be accessed normally.
2-Android won't boot.
3-Battery Drains alot.
TBH I've never faced such problem, but try to start freshly, from scratch.
1-Run task29 to remove installed ROM.
2-Flash a new ROM, different than the old one.
3- Format Memory card (without putting the back up back)
4-Try to enter bootloader (vol v-^ boot) [Your first & third problem may be solved here,proceed to next step]
5-Put a fresh Android folder, without using the old one and without using a back up .
6- Boot Android
a few questions :
What radio did you have ?
Did you flash recently a stock rom with HSPL on ?
Does this problem happen with a certain Android build or all builds ?
Feedback what happened.
Faris,
kawazaki said:
So let me summerize your probs,
1-Bootloader can't be accessed normally.
2-Android won't boot.
3-Battery Drains alot.
TBH I've never faced such problem, but try to start freshly, from scratch.
1-Run task29 to remove installed ROM.
2-Flash a new ROM, different than the old one.
3- Format Memory card (without putting the back up back)
4-Try to enter bootloader (vol v-^ boot) [Your first & third problem may be solved here,proceed to next step]
5-Put a fresh Android folder, without using the old one and without using a back up .
6- Boot Android
a few questions :
What radio did you have ?
Did you flash recently a stock rom with HSPL on ?
Does this problem happen with a certain Android build or all builds ?
Feedback what happened.
Faris,
Click to expand...
Click to collapse
Thanks, at last!
you are right, thats summarized what are the problems that ive been facing now.
I always ran task29 before any installations of new ROM
I flashed various of official ROMs and cooked ROMs. None of them giving the result that I want. The battery still draining like hell and I cant access bootloader normally. I have to pull out everything for 15mins 1st, put it back, then I can access bootloader by holding up -vol. But still, it wont solve my battery issue.
I formatted my SD thru HP, thru PC (full format, not quick format), nothing happen at all. Still cant load Haret/Android. I left it for night long, stuck at HTC logo with black background.
To Answer your questions
various Radio(s) I've tried; .50,.51 including the newest one.
yes, I flash stock ROM with HSPL on when I encounter this problem
Its happen to all build, Winmo and Android.
phew, I still believe that I've taken necessary steps in order to get back my HD2 to perform at its normal condition.
Thanks, Please advise.
Amir
amircesc4 said:
Thanks, at last!
you are right, thats summarized what are the problems that ive been facing now.
I always ran task29 before any installations of new ROM
I flashed various of official ROMs and cooked ROMs. None of them giving the result that I want. The battery still draining like hell and I cant access bootloader normally. I have to pull out everything for 15mins 1st, put it back, then I can access bootloader by holding up -vol. But still, it wont solve my battery issue.
I formatted my SD thru HP, thru PC (full format, not quick format), nothing happen at all. Still cant load Haret/Android. I left it for night long, stuck at HTC logo with black background.
To Answer your questions
various Radio(s) I've tried; .50,.51 including the newest one.
yes, I flash stock ROM with HSPL on when I encounter this problem
Its happen to all build, Winmo and Android.
phew, I still believe that I've taken necessary steps in order to get back my HD2 to perform at its normal condition.
Thanks, Please advise.
Amir
Click to expand...
Click to collapse
Maybe your HSPL is defected (Idk how would that happen)
But try to remove it, flash stock ROM 3.14, Don't HSPL, Try to run android, different build.
And never use 51 radio ! .. Always stick to 50 .. also what class your sd-card is ?
Because I've never read about your problem anywhere ..
Faris,
ive tried flash various HSPL from 1.42 till 2.08. still have same probs.
and i already tried 3.12 official rom, still batt prob and wont solve bootloader prob.
yeah, im on .50 radio now.
ive 2 SD cards, 8GB each, class 1 and class 2.
thanks.
amir
amircesc4 said:
ive tried flash various HSPL from 1.42 till 2.08. still have same probs.
and i already tried 3.12 official rom, still batt prob and wont solve bootloader prob.
yeah, im on .50 radio now.
ive 2 SD cards, 8GB each, class 1 and class 2.
thanks.
amir
Click to expand...
Click to collapse
I meant to remove HSPL, by downloading a Stock ROM , Renaming it to leoimg and put it in sd card boot device in bootloader
ok. ive done it just now. no luck
thanks btw, u helped me a lot!
You're having a major problem ! you almost resetted your device to new ! How come you're still facing problems, Have you got your phone fell of a Highrise ?
maybe hardware malfunction, who knows?
erm, maybe cotulla can help me.
Unable to load American Android 2.3 on HTC HD2.
Downloaded the American Android 2.3 for TMOUS->Extracted Android folder to blank SD card /sdcard/Android->Opened up file manager on HTC HD2 /sdcard/Android and ran clrcad.exe got the untrusted popup clicked okay->Ran haret.exe got popup again clicked okay then saw a few white command lines (maybe 5) then the green HTC logo appears and sits there for ever. I let it sit for 30 min and no change had to pull the battery and restart windows. Phone is up to date only difference might be is it has been unlocked through T-Mobile. Does anyone know how to avoid this?
Ergh
I even tried HSPL3 and that didn't help... I just want the American Android 2.3 Gingerbread to load on my HTC HD2.. WTF!
Im having the same problem as well. I did the fat32 primary partition, on a clean sd card, ill wait for 30 minutes before i give up. some one please help, i got the desire hd rom running but would like to see what the gingerbread 2.3.3 is like.
Did you flash a new radio rom?
SO, you are going from WIn 6.5 to Android just by haret ? You cannot
If I was you I would start all over flashing HSPL 3, then flash Radio 2.15, then install Magldr 1.3, then copy the zip file to sd card and install. It's as easy as drinking a glass of water.
Be sure you chose SPL 2.08.HSPL and NOT SPL 2.80 when you flash HSPL 3
valv507 said:
SO, you are going from WIn 6.5 to Android just by haret ? You cannot
If I was you I would start all over flashing HSPL 3, then flash Radio 2.15, then install Magldr 1.3, then copy the zip file to sd card and install. It's as easy as drinking a glass of water.
Be sure you chose SPL 2.08.HSPL and NOT SPL 2.80 when you flash HSPL 3
Click to expand...
Click to collapse
So I did all that and am now stuck on the MAGLDR screen and can't get it to do anything.
I tried running ROMUpdateUtility and it won't connect...
same problem need fiv
valv507 said:
SO, you are going from WIn 6.5 to Android just by haret ? You cannot
If I was you I would start all over flashing HSPL 3, then flash Radio 2.15, then install Magldr 1.3, then copy the zip file to sd card and install. It's as easy as drinking a glass of water.
Be sure you chose SPL 2.08.HSPL and NOT SPL 2.80 when you flash HSPL 3
Click to expand...
Click to collapse
Ok first off what valv507 is mistakenly thinking you are trying to run Andriod from NAND. When you flashed MAGLDR you wiped your ROM from your HD2. This is why you can not get past MAGLDR it needs a ROM to boot.
You will have to reinstall your Windows Mobile ROM (hope you dide not loose too much data ) make sure it is a 3.14 ROM as they are the best for running Android from SD. Also make sure you have the 2.15.50.14 radio or atleast the 2.14.50.02 radio, the 2.15.50.14 radio is the best though. Also reformat your SD card again but use the Panisonic software to format it as most people say it is better than the Windows software. You can download it here. Make sure you do a full wipe and format using Fat 32. Then place all of your files and stuff from your back up back on your SD card including your Adroid build. then try to boot the Android again.
Put your HD2 into bootloader to reflash your Win Mo ROM. Hold down the volume down button while powering on your HD2 to get to bootloader and make sure you see USB in the white bar of bootloader before you flash the ROM.
T-Macgnolia said:
Ok first off what valv507 is mistakenly thinking you are trying to run Andriod from NAND. When you flashed MAGLDR you wiped your ROM from your HD2. This is why you can not get past MAGLDR it needs a ROM to boot.
You will have to reinstall your Windows Mobile ROM (hope you dide not loose too much data ) make sure it is a 3.14 ROM as they are the best for running Android from SD. Also make sure you have the 2.15.50.14 radio or atleast the 2.14.50.02 radio, the 2.15.50.14 radio is the best though. Also reformat your SD card again but use the Panisonic software to format it as most people say it is better than the Windows software. You can download it here. Make sure you do a full wipe and format using Fat 32. Then place all of your files and stuff from your back up back on your SD card including your Adroid build. then try to boot the Android again.
Put your HD2 into bootloader to reflash your Win Mo ROM. Hold down the volume down button while powering on your HD2 to get to bootloader and make sure you see USB in the white bar of bootloader before you flash the ROM.
Click to expand...
Click to collapse
What if I just want to run Android from NAND? At this point I just want to flash Gingerbread 2.3 on there but want the best version of that with the fewest bugs. Do you have any links to such a ROM? How would I go about flashing it? Thank you for the help in advance.
If you do a YouTube search you cab find a "how to install " video for installing NAND Android GB 2.3.2 on the HD2, it also has links to ROMs, Radios and MAGLDR 1.13. I installed it in about 15 mins after d/ling the specified files and I have only had a HD2 for 3 days. Very good video. I would link you to it but I am at work right now and I have the page saved to face on my home PC
Sent from my HTC HD2 using XDA App
sh1fty7 said:
What if I just want to run Android from NAND? At this point I just want to flash Gingerbread 2.3 on there but want the best version of that with the fewest bugs. Do you have any links to such a ROM? How would I go about flashing it? Thank you for the help in advance.
Click to expand...
Click to collapse
If you want to go NAND Android just click on thr guide linked in my signature. I have links to two of the best guides on how to install NAND Android on your HD2 at the top of my guide. My guide is not a guide on how to install NAND Android but a guide to teach you what the things you need to install and run Android from NANN and WP7 are, what they do, and how to install them.
Also I use a non HTC Sense Gingerbread ROM and I really like it click the link for Hyperdroid in my signature if you want to check it out.
Thanks! let me learn this knowledge may.
ryu-lamp said:
Thanks! let me learn this knowledge may.
Click to expand...
Click to collapse
What exactly are you asking here? Do youi want to know how to enter bootloader?
If so you just hold your volume down button down while powering on your HD2, this brings up the multicolor bootloader screen. From bootloader you can connect your HD2 to your computer wait for Serial to change to USB and then flash what ever you are wanting to flash radio, Windows Mobile ROM, splash screen, MAGLDR, and cLK. Click on my guide in my signature to get even more knowledge.
it is possilbe to have magldr installed running whatever NAND os you want.. and still boot ACA from sdcard.
the first post of the ACA thread has all the details you need to accomplish this.
sh1fty7 said:
What if I just want to run Android from NAND? At this point I just want to flash Gingerbread 2.3 on there but want the best version of that with the fewest bugs. Do you have any links to such a ROM? How would I go about flashing it? Thank you for the help in advance.
Click to expand...
Click to collapse
to run it from nand you go to 10 services, than boot settings ,than select android sd ,than go to 10 again than select boot settings ad sd dir than select the android folder make sure there is not another folder named android, than go to ad sd nand and it will load. it tooked 15 minutes but he did say it would take long.
I took the same steps as the OP did and I'm experiencing the same problem. I am not planning to go through NAND and would like to stick with the SD build but it will not load. Any suggestions?
I'm using the latest American android build. Here is what I did:
1. Copy ENTIRE android folder to sd. If you want a faster boot time you need to copy over a new data image since one is not included in this build. It will create one on first boot, but this takes longer.
2. Once you've done this run clrcad then haret and allow it to boot. Mine took about 15 min total boot time to first lock screen without a data img. And about 7 to 10 min with.
3. Once you see the first screen DO NOT touch it. Let it settle for about 10 min. After that it should shut it self down.
4. Turn phone back on and boot android again. Letting it settle again for a few minutes. After 5 or 10 min of letting it settle pick it up and enjoy your sexy gingerbread.
Also, on a side not magldr is used for booting from wp7 to android. Haret is what is used for booting android from wm6.5
Hope this helped.
kushXmaster said:
I'm using the latest American android build. Here is what I did:
1. Copy ENTIRE android folder to sd. If you want a faster boot time you need to copy over a new data image since one is not included in this build. It will create one on first boot, but this takes longer.
2. Once you've done this run clrcad then haret and allow it to boot. Mine took about 15 min total boot time to first lock screen without a data img. And about 7 to 10 min with.
3. Once you see the first screen DO NOT touch it. Let it settle for about 10 min. After that it should shut it self down.
4. Turn phone back on and boot android again. Letting it settle again for a few minutes. After 5 or 10 min of letting it settle pick it up and enjoy your sexy gingerbread.
Also, on a side not magldr is used for booting from wp7 to android. Haret is what is used for booting android from wm6.5
Hope this helped.
Click to expand...
Click to collapse
Ok, So maybe you can help me here... Im trying to get this Latest American Android 2.3.4 and my phone is totally stock right now.. I used to have froyo 2.2 but I Hard reset my phone and formatted my SD card, So the phone is totally fac setting right now. So can you please explain step by step on what to do now and how to get that 2.3.4. Do I have to install any sort of rom or something?
btw here's the thread where I found the build
http://forum.xda-developers.com/showthread.php?t=957652
Please reply quick because I am dying without Angry Birds lol!
Android
I have to post 10 post before I can post to another thread. 1
HI BOYS...
I have had a problem with reflash to the HD2, installing WP7, the new version with NODO, has made to depart the whole procedure without inserting the SD...
When I have realized of I mistake it, I have reformatted the DEVICE and referred everything... but at the end of the trial when it had to load the WP7 you/he/she has given me: 1234FATAL hits 4
Don't I now succeed in making to correctly depart WP7, WE can help me in this problem to resolve ?
HELP ME!
have you try to flash to stock ROM winmo 6.5?go to tricolor screen and flash back to original ROM,then task29 your SD card and follow the steps to re-flash WP7 ROM. Hope this help.
in practice reloading WP7 I have noticed that he/she doesn't write me nothing on the SD, I will now try to flash the original ROM...
If some good boy has other ideas they are here to try...
<<<RESOLVED>>>!!!!!!!!
Return back to the origins is always the best solution--- now the OS Funziona!!!!!!!!!!!
Tomorrow I retry to install WP7,
THANKS,
I hope both profit to you this post,
Regards and good flash
fatal hit possible cure if happens
first sorry i didn't see this earlier but had same problem if you have an extra sd card like 2gb and reflash rom then use the other card so nand can clean up the mess in part4.nbh don't ask me why but work for me also if it still happens you might what to check sd card and make sure it class 2 or if first partition is degraded
I'll try to explain to problem I'm haviing as best as possible.
I have an HTC HD2 that worked fine up until I tried to switch the phone from Windows 6.5 Professional to Android Gingerbread. I thought I followed the instructions right. I loaded HSPL4 (whatever that is), Loaded DFT NAND MAGLDR 1.13 and what I thought was Android 2.3.4 (it was actually 2.2).
After it was done, I have no internet service (even though the phone says I am registered with T-mobile, have a good sign and receiving service). My phone works but I can't hear the caller (they hear me fine). I can send/receive texts. Wifi works fine. I also can't Synn up with my PC.
I have a SD card available if I need it. I'm furstrated and mad I can't use my phone. Right now, I would be happy with setting my phone back to stock but I really want Android Gingerbread.
Thank you in advance for your assistance.
Hey.... I think you have flashed an outdated rom.... So all you have to do is to flash a new and better one... I would prefer MIUI.. it is a fast and clean build with least bugs... To download the rom.. I would say... Go to MIUI.US download the latest rom for hd2 from there and paste it in your SD card.... Then go into magldr screen by pressing the red button when booting up... Select ad. Recovery.. Then in the new screen... Select wipe data/factory reset.... Then select install zip from sd card.... Choose zip from sd card and then after it is complete boot into your new rom by restarting... But warning... If with the current build of magldr... Your battery runs out... You will have to charge the battery external... If you want to prevent this then i would say that you rather install clk it is similar to magldr... But supports off mode charging... To know how to install clk I have posted a thread on installing miui... How to... Check out there you will get the guide for clk installation
Thank you
I'll give it a try and let you know how it went.
hello all i was trying to install the android on my hd2 phone
got all the way to where i ran the rom updated utilerty and now its stuck on the htc screen ,at load up of the phone
i have read about this happening ,
and read that you hold the volum button and power and boots up ,,,which it does goes to system and the plug it in to my laptop ,,,,,
then get the USB on the screen of the phone ,,,,
but i dont have a rom to back it up with ,,could some one please point me in the right direction of where to get this fome and how to get it to work thanks
moose579 said:
hello all i was trying to install the android on my hd2 phone
got all the way to where i ran the rom updated utilerty and now its stuck on the htc screen ,at load up of the phone
Click to expand...
Click to collapse
I assume (since about ten people per day ask exactly this) that you flashed magldr but magldr didn't start as expected? This is caused by (as I type half a dozen times a day) by not having 2.08.hspl AND a compatible radio.
i have read about this happening ,
and read that you hold the volum button and power and boots up ,,,which it does goes to system and the plug it in to my laptop ,,,,,
Click to expand...
Click to collapse
bootloader
then get the USB on the screen of the phone ,,,,
but i dont have a rom to back it up with
Click to expand...
Click to collapse
not sure what that means, sorry.
,,could some one please point me in the right direction of where to get this fome and how to get it to work thanks
Click to expand...
Click to collapse
You haven't given any real details as to what you have done so far.
Details details details.
So, tell us what you did so far, please. Please be detailed, with names, filenames, versions, etc. not just 'i flashed that thing and now nothing works'
hope this helps more
ill start from the start
i first ran this file HSPL3_PKG.exe this run fine without any problems
then i ran this file rom updateutility from this rar folder ive downloaded called DFT_LEO_MAGLDR113_DAF
now this is where it all went wrong ,i ticked all the boxes and went thought the set up by following this video
got to 6;08 into the video and followed the steps
then got to 7;04 in the video and this is where the phone stayed on the htc screen for 30 mins ,,,and its done nothing
so i unplugged it
now i read that its possible to get the phone back to booting up with another offical rom from htc but carnt find the rom that ill need ,,plus the windows mobile wont reconise my phone in usb mode
hope this helps you a little more to solving my problem
and sorry i carnt post the link to the video yet as ive not done my 8 posts
ok, so its all fine so far, you just haven't yet done the next step, which is flash a compatible radio. (had you changed the radio after flashing hspl and before flashing magldr, magldr would have started straight away)
(I shall assume that you have a regular hd2, not a t mobile US model, since you haven't said, if it IS a tmous, then its a different problem)
download radio 2.15.50
enter bootloader
plug in usb
count to 5
run customruu to flash that radio
reboot
magldr should now start
thanks for your reply
ill go and find this radio now and keep you posted
thankyou
you rock dude
thank you so much for your time posting ,,
100% working andriod now
anything eles i should know please post
Lovely.
Only thing to know is that you shouldn't need to flash radio or magldr again now, if you want a different sized rom you may have to reflash cwm to change partition size, but if you ever have probs booting or whatever, nine times in ten someone will tell you to task29 and reflash stock and start over,,,, nine times in ten that's massive overkill.
Read read read is the best advice I can offer, see what issues others have and read the answer,, one day that issue might be yours, and you'll have a head start solving it. Never panic and start random flashing, that always ends badly, and means any help request posts are harder to work with.
thank for your reply
just a quick question for you
ive got a 16gb sd card in with about 300 app/games ,,and ive installed about 20 so far but now phone says memory full ,,should they be installing on sdcard instead of the phone memory
or is this normal for the phone memory to run out so fast
Depends on the rom, some leave 200+ free, some far far less. That's why most roms support an ext partition, which the phone treats as internal.
Backup your SD card (it will be wiped) start phone into cwm, then (I think its) advanced - format SD card, or something like that. Create a 1 or 2 gb ext partition, swap 0, and reflash the rom. C
The rest of the SD will be formatted to fat32 just like it is now.
It will detect the ext partition and use it as internal memory automatically. You should not choose the option to "move app to SD card", that will take the app off the ext partition and put it in the fat32 partition,, and some apps wont work from fat32.(angry birds for example)