Database Users

Has anyone fixed/soldered a broken power button?

I tried to replace my vogue after the screen cracked and power button broke, but Sprint/Asurion want $100 to replace it. Turns out it was only the digitizer that cracked so I'm trying to fix the power button myself, then simply replace the digitizer for ~$10.
My problem is that the power button completely broke off from the mainboard. I tried to solder it back on without a result, and I'm wondering if I'm missing a step. The board has 5 separate solder points, but it looks like only 3 are actually making a connection to the button (so I soldered only those). From the looks of the soft reset button, it seems that the two other solder points don't actually bridge any connections, but are touching the underside of the button where it's not metallic.
Obviously I'm missing something here, anyone have a clue?

hate to say it but id just pay the $100 for a refurbish or id look on craigslist or ebay for a replacement.

All you need to do is solder those three solder points. make sure you are using flux so it flows well and keep it straight. I had an issue after I put the case back on and the button on the case not lining up with the switch. Make sure you try to power the phone on before you put the case back on. I would leave the digitizer plugged in just in case.

Using the simple diagram below, soldering the 1-2-4 points didn't make it work. I was able to mimic the button by bridging the 1or2or4 with the 3or5.
1___2
3_4_5
Not sure what else I can do at this point beyond putting in a small momentary button that makes one of these connections, it will make the device look incredibly ghetto though

it is possible when it broke off it took one of the solder pads with it, after you take the button off see if all the connection points are still silverish in color if any are tan unfortunately you will have to go through asurion, there is no way i know of restoring them after that point

Power button not functional

Hey guys, I was just using my phone today like a normal day, and my phone's power button just stopped working. I doubt its software, so is there anything I can do to fix this? Any guides in particular?
edit: the button has randomly started working again after I pushed it in a bit without opening anything, but I suspect theres dirt accumulating in there or something and just making it hard to work. I'd still like to know if theres a way i can get the power button out, clean it with a q-tip or what not and get it back in all safely.

Sorry to hear that, bro. Judging from this Vibrant tear-down thread http://forum.xda-developers.com/showthread.php?p=24155781, it looks like the power button is accessible after taking off the main back cover ... but I can't really tell from the 2nd photo (looking at it from my phone / Tapatalk right now, and the zoomed resolution is not very good).
Hope you get it figured out, or maybe (in the meantime) use a power button widget / shortcut?
( not to make light of the circumstance ... but maybe make sure you're using the right "towels" when you wipe down your phone. Its always easy to blame dougie's special red apk. )

Hey xriderx, it is pretty easy to replace the power button ribbon. Just dont tear the pad off the board like I did. I found the ribbon online for about $10. What you are describing is exactly what my power button did before going out completely.
Sent from my SGH-T959 using XDA

cixdk said:
Hey xriderx, it is pretty easy to replace the power button ribbon. Just dont tear the pad off the board like I did. I found the ribbon online for about $10. What you are describing is exactly what my power button did before going out completely.
Sent from my SGH-T959 using XDA
Click to expand...
Click to collapse
How can you detach the power button ribbon and replace the by the new one? do you have to solder or anything ?

Yes it will require some soldering. Maybe some desoldering tape to remove the old ribbon/solder as well.

HTC HD2 assembly problem

Hi guys,
I just disassembled my HD2 to replace my broken digitizer and touchscreen.
But now i'm stuck with a problem.
What shall I use to glue both items together again?
And the keyboard makes some issues.
I tried to place both parts over eachother to see if they fit but I can't press the keys after it.
Seems like they are stuck.
That's why I didn't want to use superglue because after assembling it I wouldn't be able to change anything.
Maybe pictures tell more than words.

http://www.youtube.com/watch?v=t8Q7mXdcJ54&feature=player_embedded
hope that helps you

thanks wasn't the information I was looking for but nevermind
I assembled the device now .. but the next problem occured ..
the hd2 is loading without problems (led shows it) but when I try to power it on it's completely dead. nothing happends
with my old touchscreen it was at least possible to power it on.
my question is:
could the new soldered touchscreen + digitizer be broken? or did I break something during disassembly and assembly?
To be honest I didn't see any mistakes I made.
It's not my first time repairing stuff like that because I used to repair notebooks as a hobby.
Still i'm unsure what the heck is going on with my phone atm.

did you check if the flex cable from display is in the port, there is an white stripe that shows how far it must in the port. Did the phone vibrate when you pressed power button?

I checked the cables and found nothing suspicious.
and the phone didnt even vibrate after trying to power it on.
I'm trying to get a new hardkey board (i hope you know what I mean).
Had problems with the keys being stuck and maybe I killed that one by trying to assemble it.
if the phone doesn't recognize me pushing the power on key it's no wonder it won't do anything.
hope this will fix the problem

12dollar said:
I checked the cables and found nothing suspicious.
and the phone didnt even vibrate after trying to power it on.
I'm trying to get a new hardkey board (i hope you know what I mean).
Had problems with the keys being stuck and maybe I killed that one by trying to assemble it.
if the phone doesn't recognize me pushing the power on key it's no wonder it won't do anything.
hope this will fix the problem
Click to expand...
Click to collapse
Most likely something is wrong with your Power button, but you should turn it on with 2nd method:
- pull out battery;
- insert usb cable(connected to PC)/charger in your usb port;
- insert battery.
This way it should turn on whatever OS you have installed on.
If your OS is Android through MAGLDR, connecting it through usb should turn it on by default, unless your battery is not dead!
Check it out!

bib*oops said:
Most likely something is wrong with your Power button, but you should turn it on with 2nd method:
- pull out battery;
- insert usb cable(connected to PC)/charger in your usb port;
- insert battery.
This way it should turn on whatever OS you have installed on.
If your OS is Android through MAGLDR, connecting it through usb should turn it on by default, unless your battery is not dead!
Check it out!
Click to expand...
Click to collapse
I just did as you said and yeah the phone came to life.
so there is definately a dead power button (probably the board is broken)

12dollar said:
I just did as you said and yeah the phone came to life.
so there is definately a dead power button (probably the board is broken)
Click to expand...
Click to collapse
Glad to hear that!
Definitely you should replace your keypad flex!

Did you fix the problem with the hardware keys
Hi,
I have very similar problem.
I changed the touch screen on my HD2 and after reassembling I cannot get the hardware keys clicked.
I ordered a brand new key board and brand new plastic buttons. I received them but situation is the same.
If somebody can explain is there any trick during adjusting the plastic buttons to the clickable "small dots" on the board - please help me.
Best Regards

maznevh said:
Hi,
I have very similar problem.
I changed the touch screen on my HD2 and after reassembling I cannot get the hardware keys clicked.
I ordered a brand new key board and brand new plastic buttons. I received them but situation is the same.
If somebody can explain is there any trick during adjusting the plastic buttons to the clickable "small dots" on the board - please help me.
Best Regards
Click to expand...
Click to collapse
Normally this is always down to glass digitizer not being aligned correctly when stuck to LCD.
0.05mm can make all the difference here.
You need review current digitizer position & pre test assembly to centre chassis without tape for a test run on button function.
Also check button board position is exact & located correctly in the pin holes at each end of the board.
original board quality is normally far better than most of the very cheap eBay pattern parts but one or two sellers offer a decent board around $4.50
Also clean all old tape from back of LCD & centre chassis plate so parts fit flush & once all checked new tape can be added, I also use small spots of up40 adhesive sealant near corners & near middle edges for final build up as holds far better than even the best tapes & gives an original strength & long lasting flush look to final job plus us easily removed with razor blade if repair ever needed again.
Super glue is a BIG no no NO.

Hard to get hardware buttons clickable
Mister B said:
Normally this is always down to glass digitizer not being aligned correctly when stuck to LCD.
0.05mm can make all the difference here.
You need review current digitizer position & pre test assembly to centre chassis without tape for a test run on button function.
Also check button board position is exact & located correctly in the pin holes at each end of the board.
original board quality is normally far better than most of the very cheap eBay pattern parts but one or two sellers offer a decent board around $4.50
Also clean all old tape from back of LCD & centre chassis plate so parts fit flush & once all checked new tape can be added, I also use small spots of up40 adhesive sealant near corners & near middle edges for final build up as holds far better than even the best tapes & gives an original strength & long lasting flush look to final job plus us easily removed with razor blade if repair ever needed again.
Super glue is a BIG no no NO.
Click to expand...
Click to collapse
It is not the case in my case , because I ordered full set (digitizer + display) and they arrived factory assembled.
But you are definitely right - 0.05 mm make the difference. I think the problem comes from the fact that the board with buttons cannot be firmly fixed to the 2 small juts on the chassis. You know the plug of the buttons board is on the tail like extension. Probably when I try to cover the buttons board with the LCD+digitizer - the frame of the LCD slightly pushes the buttons board and the juts on the plastic buttons cannot be fixed exactly on the top of the actual buttons on the board. Anyway we are speaking about precise fixing something around 0.05 mm over something else, which is exactly same size... and in the same time you have to fix this without any visibility.
I will continue trying. If you can give me any other ideas - I will appreciate this.
Thanks

maznevh said:
It is not the case in my case , because I ordered full set (digitizer + display) and they arrived factory assembled.
But you are definitely right - 0.05 mm make the difference. I think the problem comes from the fact that the board with buttons cannot be firmly fixed to the 2 small juts on the chassis. You know the plug of the buttons board is on the tail like extension. Probably when I try to cover the buttons board with the LCD+digitizer - the frame of the LCD slightly pushes the buttons board and the juts on the plastic buttons cannot be fixed exactly on the top of the actual buttons on the board. Anyway we are speaking about precise fixing something around 0.05 mm over something else, which is exactly same size... and in the same time you have to fix this without any visibility.
I will continue trying. If you can give me any other ideas - I will appreciate this.
Thanks
Click to expand...
Click to collapse
Do not rule out the LCD/Digitizer assembly as the china combos are prone to not the best accuracy of assembly as sounds like maybe LCD is mounted just a fraction too low on the digitizer perhaps.
Button board should be fixed via 3M style tape & most replacement boards come with tape ready for fitting.
worth making effort with button board to centre chassis to mount securely then mounting lcd to chassis without tape for a trial assembly & try and check for possible issues such as bent chassis or old tape not removed sufficiently or new assembly alignment not the best.
I would also recommend using original plastic button strip as the copy ones are not always good & have had experience with them before.

[Q] Power button not working

I cracked my screen and replaced the screen, digitizer, and frame. Before replacing it the power button worked fine, in fact turned on just before I got the case off annoyingly. Replaced all the parts, made sure the power button pcb was in place, and charged the battery which causes the screen to light up. But now the power button is not turning on the phone. I'm a bit confused, it feels like its hitting the button. Wonder if anyone has run into this problem when tearing apart there phone and putting it back together? I'm going to check the power button pcb again, and try to power it up with the back off.
Edit: Torn it apart again, checked the power PCB board with my multimeter and I have continuity when the button is pressed. Made sure the power button is touching the logic board to. I starting to think my logic board got fried when I torn it apart. Would the logic board be fried if the screen still lights up when you plug in a charging cable?
Solution: Figured it out. The bent contact pins that touch the logic board 1 had been bent to much in while disassembling and reassembling so it wasn't actually touch the logic board. Couldn't see it till I could the tiny power pcb board out.
Also figured out how I bent it. When you take the black plastic cover off the logic board the clip on the left side is a bit tricky to get off. The only good spot to get under the cover is right next to the power board, and I happen to wedge my pry tool at some point between the logic board and the pin on the power PCB. I also found out I did the same thing on the volume PCB for volume down. So just an FYI to watch out for that when taking this thing apart.

S4 not charging/ turning on

hi there just had my screen replaced and now i cant seem to turn my phone on
if i unscrew the casing the motherboard moves slightly and the phone turns on, trying to put the casing back on is impossible without the phone turning off again?
any ideas of what i can do? all the plugs seem pretty tight and connected?
thanks

danay said:
hi there just had my screen replaced and now i cant seem to turn my phone on
if i unscrew the casing the motherboard moves slightly and the phone turns on, trying to put the casing back on is impossible without the phone turning off again?
any ideas of what i can do? all the plugs seem pretty tight and connected?
thanks
Click to expand...
Click to collapse
Hi mate
Seem like the power button is jam or broken.....was it working before the display was replaced?

hi thanks for the reply,
yes it was all working ok, im not sure about the power button? it seems to work fine when in the right spot
https://www.youtube.com/watch?v=BvZNlsbWuEs

I'd go with the phone to a local repair shop and show them what happens.
Since it turns on when it's only in a certain position, it must me some faulty contacts.
When the screen was replaced they might have damaged something.
Was it done in a local repair store? If so, did you check the phone before accepting it back?

have you tried disconnecting front camera, ear-speaker or proximity/light sensor, camera or hardware button flex cable one by one, to check if problem persists? i believe thats may be connector related problem.