Related
Today in evening my cell phone switched off after the battery died.
I put in the USB charger and once it started to charge I instantly at that moment switched it on, it showed the blue startup screen and vibrated and shut off again (I presume it was not charged enough at that moment to be switched on), I again instantly switched it on as it was charging, it showed the blue screen again, gave a long vibrate and shut off. Since than I have not been able to switch it on at all. It dosent even vibrate or show the blue startup screen at all.
The red led on top is on as it is in charging mode, but it has been like that for past 6 hours, after few hours the red led turns off automatically so I had to unplug and plug it again to turn the charging on again.
I have been pressing the power on button but nothing happens, I even tried doing the hard reset but nothing happens. Except the red charging light it has been dead for past 6-8 hours even after I have been charging it for that long.
What should I do?
And the bad thing is I live in US and got this phone from UK, so I dont think I have any warranty as www.expansys.com mentioned it earlier that this is UK based phone and their is no warranty in US.
I'm not sure you can just brick the hp by charging it. Try the following:
1. Remove the battery and plug in the charger. The ipaq works without battery only on external power.If yours doesnt, then the battery isn;t causing the problem.
2. Remove all sim and micro sd cards if you have put any. Leave the ipaq only as it is out of the box.
3. If it doesnt turn on either way, you have to try to restore the rom.
How to do that? Easy.
a) turn the device off. put in the battery and plug in the charger. Then press the record buton (on the right, just under tha jog wheel or whatever it's called)
and while holding it, pres the power on. It should turn on and over the blue screen ypu see "clean boot" Just leave it, take a deep breath and wait. DO NOT TOUCH IT until it boots windows and asks you to tap the screen. IF nothing happens you have anther option - go to the HP site and find the rom update - it's 53mb and it's a little tricky to find. Then turn the device off and run the rom update utility from PC. If this doesn't work, then i sugest you contact HP support online chat and ask for help (Not likely to get any).
READ THIS:
http://forums11.itrc.hp.com/service...277571&prodTypeId=215348&prodSeriesId=3544506
Just do some research. Google it. Go to the hp site and try to find someone with the same problem.Don't just sit there. You have INTERNATIONAL WARANTY. In the worst scenario you can send the davice to HP in the UK and get replacement unit. If you haven't dropped, spilled on with water or charged with higher voltage(which i think you can't do in the US, as you have 110v circuits.) you can call HP support in your country, bring it there and just ask for replacement.
Don't try to flash it with roms provided on the site - it's not for first time users. Read, research and ask, before destroying your device.
axlastro said:
I'm not sure you can just brick the hp by charging it. Try the following:
1. Remove the battery and plug in the charger. The ipaq works without battery only on external power.If yours doesnt, then the battery isn;t causing the problem.
2. Remove all sim and micro sd cards if you have put any. Leave the ipaq only as it is out of the box.
3. If it doesnt turn on either way, you have to try to restore the rom.
How to do that? Easy.
a) turn the device off. put in the battery and plug in the charger. Then press the record buton (on the right, just under tha jog wheel or whatever it's called)
and while holding it, pres the power on. It should turn on and over the blue screen ypu see "clean boot" Just leave it, take a deep breath and wait. DO NOT TOUCH IT until it boots windows and asks you to tap the screen. IF nothing happens you have anther option - go to the HP site and find the rom update - it's 53mb and it's a little tricky to find. Then turn the device off and run the rom update utility from PC. If this doesn't work, then i sugest you contact HP support online chat and ask for help.
Click to expand...
Click to collapse
When I tried step 1, all LED lights just started blinking, I tried powering it on but nothing happened.
Tried restoring ROM by pressing the buttons you mentioned but nothing happened. No power no clean boot, just switched off.
I downloaded the Rom from HP website and strange thing is to download it I selected the option on HP Website 'Detect my device' and they did detected my Ipaq 614C, but after running the file it goes to the screen 'Please wait shile the device state is verified' and than it fails to recognise my device!
Even when I know everything is firmly attached.
What is the PC you're using. Can you try to plug the usb cable in another slot.Did your ipaq work at the beginning.
Do you have Active Sync 4.5 installed? XP or Vista. XP is recommended. Is the update 53Mb (not the 1 mb one). When having hardware problems, the trick is to alter the variables - use different connectors, cables etc, different settings and so on. This ipaq is cheap for a reason - there are lots of faulty units, but that's why waranty is for - if you have a document for the purchase, you have international waranty. That's it. Before going to HP service center, try all possible options mentioned here again on a different PC with all the software needed - Active Sync 4.5 and usb drivers that may be included in the CD that comes with the ipaq. If the HP website recognises the devie it's almost sure you don't have a brick, as it probably verifies the EBOOT - the most vital part of your device's memory. Try upgrading a few times no matter the error. Restart the pc and so on. My advice - ask for online support or just call HP support. Be insistive but polite. If they say "go to the service center or something like that" just continue asking. Write down your case ID. Use online chat help on the HP site, even though your device is not listed, choose IPAQ 500 or 214 and just enter the SN and PN (on the back, under the battery) and Tell them your device model.
http://forum.xda-developers.com/showthread.php?t=426418&highlight=614c
Probably WAY too late but I've just acquired a sickly 614C which I've nursed to health.....
There seems to be some bizarre issue with the charger in the 614c so that if the battery level falls too low, it requires a mains-connected USB charger rather than just the USB port on a pc/laptop.
If your 614c is the same as mine, the red LED will be pulsing very slightly when connected to the USB port but a solid red when connected to a mains USB charger.
Once the LED turns amber, it can then be connected to the USB port for further charging. It looks like it just needs an extra boost when the battery is completely flat.
HTH!
hi
i had the same problem when i left my phone uncharged for over a week. after reading about the same issues some of us encountered i came up with a simple idea that worked. i just connected the charger to the phone and long pressed the reset button (over a minute) till the red blink dissapeared and slowly the amber one took its place then i left it to charge.
Hi, I start this new thread as a new user and my first message because I'm really really worried about my samsung galaxy 10.1 tablet, It is a wi-fi only tab I bought through Amazon, and has just arrived to my country, Costa Rica, so, as any normal person, I opened the box, readed the manual and turned it on, and started checking everything in the tab, and when finished, (because I don't have wi-fi yet) I turned it off, and started to charge it with the factory charger (AC conector) it has been 5 hours since then... It has not turned on again, no matter if I press the On button 30 seconds, nor turning it on conected to a computer, or to the AC, or without anything, so I called support, and they said the same thing I was expecting, charge it and see what happens, and nothing happened, I'm really really worried about my tab, 600$+shipping is a BIG amount of money to have invested, the computer is brand new, as you will buy it from the second link availabe in amazon when you type samsung galaxy tab 10.1.
Can you help me?
Tab does not turn on..
What finally happen did it turn on...If not there is a why to reboot it by holding the vol. button and the Power.
Hope it went well, don't give up..
That is why I made this thread, I already tried the volume technique, with +, with -, with both, with + and shaking, with - and shaking, and all those with also touching the screen, an nothing!!
when you turned it off and plugged it in to charge, did you notice anything appear on the screen indicating that it was charging? Normally when turned off and plugged in a battery will appear on the screen. even if the screen turns off you can touch the power button to show the battery again.
If no battery ever appears, then it looks like you were not receiving a charge in the first place so the tab can simply be dead of juice.
Yes, the first time I turned it on I saw the battery, but when I turned it off, I never saw it again, even in this 10 hour period that has been charging on different outlets to see if the outlet is the problem.
Even I used a pencil tipe voltage tester, that tells if an outlet has voltage current, and the voltage could be felt around the tablet when charging.
But the screen does not turn on when pressing the button, nor touching the screen.
as a test, use just the usb plug and connect it to your computer. it shouldnt receive alot but see if that will initiate the screen turning on displaying the battery.
No, it does not turn on even when conecting it to the computer, it appears a message of no controlers found in the computer, but the divice does not turn on at all
Coliner said:
No, it does not turn on even when conecting it to the computer, it appears a message of no controlers found in the computer, but the divice does not turn on at all
Click to expand...
Click to collapse
idk then man, it could be the wire or it could be the tab itself
Besides something wrong with the GTab, I guess it could still be a defective cable.
Yes, it could be a possibility, that the wire is bad, but also, I can mention that in the time it was on, and working, I exchanged a couple of photos for my wallpaper, photos that I took with my camera long ago, so, if conection means, the cable I think works ok.
this happened to me.. tab is finished, send it in for repair and you will receive a refurb....
Coliner said:
Yes, it could be a possibility, that the wire is bad, but also, I can mention that in the time it was on, and working, I exchanged a couple of photos for my wallpaper, photos that I took with my camera long ago, so, if conection means, the cable I think works ok.
Click to expand...
Click to collapse
Did you press power and volume down at the same time for at least 31 seconds for samsung logo to come on?
Sent from my GT-P7510 using Tapatalk
I've tried with the volume key and the power key at the same time for almost a minute, without being conected to the charger, and being conected, also tried conecting it to the computer, and downloading the drivers that samsung offer in the support page, and samsung kies, but they don't recognice the device, when checking the hardware of my computer, I see inside the tab of "other devices" one called APX that I know that is my tab, and says no controller is assigned to it.
Mackie, yesterday (today) I chatted with a support agent of samsung until 2am, trying to see for a solution, but he couldn't find one, so, we ended up in making a request for service, to use the warranty for them to repair/give another machine to me, but, I don't want to do it, because, it would be enormously expensive for me (100$ for a Costarrican is very expensive) so, I'm trying to find a solution to the problem before I send the tab to the US with a friend that lives there, so I can use the warranty, but that courrier charges would be really expensive for me.
In summary, I'm trying and trying to look for a solution, testing your comments and suggestions, and also at the same time looking for myself for an answer.. before december 8, when I plan sending my tab if anything works.
Once, this happened with my nokia e71, but because it ran out of battery, and won't turn on again, but... cellphones are easy, you can change the battery, and actually, it worked, and when I had time to take him to repair, they checked him with the old battery, and it worked again... Tabs are horribly sealed tight and I would lose the warranty if I try to open it to change the battery, and it might even not solve the problem!
i don't know if this would help.
I had the same situation and i thought mine was dead.
I pressed the volume button as long as i can. Took about almost a minute.
Sorry if this doesn't help
people please read previous comments, Coliner has stated numerous times in different posts that he has tried the power+volume method and has had no luck so please stop suggesting it
Coliner, the only other thing short of paying the money for the exchange/repair is to attempt using a different cable. you stated before that you used both the usb partial charge and the actual A/C charge method and have received no results. The only thing I can suggest is to try a different cable, if anyone else you know has pretty much any of the galaxy tab (7", 7+, 8.9", 10.1", 10.1v) then you can attempt to charge it. Or hell, see if any store has any of them on display charging, explain your situation and ask to let you give it a shot and if it works buy the cable from them if possible.
Short of prying the thing open to play surgeon, these are your only options.
NyPlaya, today, I'm going to the capital (the only place you could find something similar) and look for stores with tablets, and also directly to a samsung store, ask for a charger, and to see what happens, and try again to turn it on at my house, I've let her charging for 2 days now, continuosly, lets hope it worked!
Coliner said:
NyPlaya, today, I'm going to the capital (the only place you could find something similar) and look for stores with tablets, and also directly to a samsung store, ask for a charger, and to see what happens, and try again to turn it on at my house, I've let her charging for 2 days now, continuosly, lets hope it worked!
Click to expand...
Click to collapse
I re read your post and i think we missed a big clue. You said you can see APX device in control panel. Apx is nvidias debug mode and in this mode (usually reached via power and volume up) the screen is blank. it is waiting for nvflash command. Check this thread for more info http://forum.xda-developers.com/showthread.php?t=1324461
So wonder if volume up button might be stuck
Sent from my GT-P7510 using Tapatalk
Well, I tried the procedure, and got to step 17... How do I run that command, how, where? so I then uninstalled the controler, and now not even the APX error appears, and tablet is still dead!
Also I went looking for chargers in stores, and they did not have chargers! so I couldn't test it!
I was searching in other forums and found this other clue:
Taken from http://www.htcmania.com/showthread.php?t=274687 post #14:
"What you run "dead" after having it at night charging, is something that unfortunately is still quite common. It happened at the beginning and pulled by soft reset, ie power button volume button -. It has happened a few times and this has been solved. I think it is related to removing the charger. Unplugging from the wall and then the tablet does not usually fail, but if you disconnect first tablet, it "dies." I tried also to turn on the screen before unplugging and so has not failed me to unplug the tablet first. Clearly a bug, I do not know if Samsung or Honeycomb, but obviously it is a pretty annoying bug. regards"
I remember I did that same thing! because my tab was conected to the PC, and I discovered it was not charging, I conected her to the AC in the wall, and without taking the 30 pin conector out, and boom, never again it has turned on!
I continued searching and found another method, power button plus volume- 10 seconds, release and volume + for some seconds, then conect to PC, and the driver appeared again, in this case Nvidia USB boot recovery
I continued to try the method shown to me by animatechnia, and typed nvflash --bl bootloader.bin --go, it says then:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Windows\system32>cd C:\nvflash
C:\nvflash>nvflash --bl bootloader.bin --go
Nvflash started
rcm version 0X4
Command send failed (usb write failed)
C:\nvflash>
READ THIS, IT'S HAPPENED TO ME
Shortly after buying my tablet, before rooting, my tablet was charging and would NOT turn on. I read somewhere to do this:
Put your finger on the screen while holding the power button for as long as you must.
Don't let go til it comes on.
Edit: best of luck if that doesn't work. Things like this suck.
First time I tried with the finger, I forgot to disconect it, so, my pc started making sounds of conected device, disconected device, just like an USB stick, then I took the cable off, and tried for more than a minute both finger and power, and nothing happened
I went out for a while with my battery at 20%, when I came back it had drained out. I put it to charge, but when I tried to switch it back on, it refused to boot. On a normal power button press, it would vibrate 3 times and then the red notification light would start blinking. Same thing with power + volume_up. If I press power + volume_down, it would vibrate 5 times and the green notification light would stay lit. Nothing comes on the screen, whatsoever.
I was rooted with S=off, and was using the Operation Inferno ROM (which I have been using comfortably for the past month or so).
I did try some stuff with ADB, such as using it to reboot into bootloader and recovery (same 3 vibrate + red notification light), pushed the Operation Inferno ROM again to the sdcard and tried to restore the ROM from that location (for which I got adb: unable to open file /sdcard/backup.zip).
I haven't yet gotten around to downloading and installing the factory image some have suggested for the eMMC issue (PD15IMG.ZIP) but I wanted additional opinions considering most people with an eMMC issue have been able to open HBOOT at least.
When the phone doesn't power on, neither ADB nor fastboot will help you. There is no device on the other side, so all your attempts went to the drain, and it was expected. Nothing to do with eMMC issue or anything else. Your phone just doesn't power on.
Put your phone to charge, if the light turns orange - just leave it to charge until it's green, then disconnect and try to power on.
If the light doesn't turn orange, or it doesn't power on even after charging - remove the battery for 10 min, press Power button for 1/2 min, release the button, reinsert the battery, put to charge. And again, let it charge before you try to turn it on.
I did charge it earlier (for about half an hour or so) and the orange light does come, but it didn't boot after that either.
I'll just give it a try by charging it through the night and see.
I think a key thing is to take out your battery for 10 min, as Jack_R1 suggested. Then proceed with the charging.
Sent from my HTC Glacier
Still doesn't work. I dissembled it and kept it like that for quite some time, then put everything back and charged it for hours. Still the same issue happening during boot.
Connect the phone to USB, powered off, see if the PC recognizes "QHSUSB_DLOAD" device. Try to power it on, see if it happens.
If it happens - it means your primary bootloader is screwed, in another words - no repair (actually, repair is theoretically possible, but no guide, no information and no sources exist for MT4G).
Jack_R1 said:
Connect the phone to USB, powered off, see if the PC recognizes "QHSUSB_DLOAD" device. Try to power it on, see if it happens.
If it happens - it means your primary bootloader is screwed, in another words - no repair (actually, repair is theoretically possible, but no guide, no information and no sources exist for MT4G).
Click to expand...
Click to collapse
When its plugged in, its recognised by the ADB (even when powered off), and I can do some basic commands (mentioned in the first post). When I power it on the same thing happens as when it wasn't plugged into USB (ie, the vibration and the blinking LED).
I'm also worried about water damage, since a very tiny amount did come on it as I was sweating profusely. Although the indicators in the battery tray and on the battery itself don't signal damage (they're completely white) I've just decided to try and keep it opened up in a bowl of rice, just in case, until someone is able to come out with some idea.
As I'm in India, taking it to T-Mobile is not an option. If nothing works out, I might take it to HTC and see if they can help out.
Hello.
When I try to turn on my N4, I hold power button, and after about 10 seconds Red light blinks (just once, if it's connected to USB that 1 blink last for 3 seconds, if connected to wall, it's just quick 1 blink. If it not connected anywhere there is no action at all, it just stays dead, no blinks, nothing). Same if I try to go in bootloader by holding volume down+power.
This happened after I successfully installed CM12, with no errors. Then I rebooted my phone, and it just stayed black as it is now. Battery was around 25~30% that time, and phone was connected to USB.
Did I bricked my phone totally? I am now trying to charge it up already for 1 hour... but it nothing changes.
I have searched here for similar problems, but couldn't find solution...
Edit: Charging already for 10h+ , still same..
Edit2: I removed battery, reconnected after a while, still same problem.
So I tested it with multimeter, it says 2.6V, but fully charged must be 3.8V. Could this be a problem? I was charging it for whole night.
Edit3: I just got new battery . But it looks the same.. phone doesn't boot up.. same red light blinks once.. so.. its my phone is dead? I can't believe that...
When I connect to PC usb, there are unrecognized deviced called "QHSUSB_DLOAD".
easy fix
Hold down the power button and the volume down button at the same time until phone reboots. If you see the little android no need to worry just let go and wait for your device to reboot on its own. This is not a factory reset it's just like restarting your device. :good:
zelexon said:
Hold down the power button and the volume down button at the same time until phone reboots. If you see the little android no need to worry just let go and wait for your device to reboot on its own. This is not a factory reset it's just like restarting your device. :good:
Click to expand...
Click to collapse
I have tried that many times. Nothing. It's bootloader screen, but I can't get there. Nothing happens. If I keep holding volume down+power it just keep blinking once every ~10 seconds, same if I hold just power button. If phone is not connected to charger, there are no blinks at all.
I removed battery, reconnected after a while, still same problem.
So I tested it with multimeter, it says 2.6V, but fully charged must be 3.8V. Could this be a problem? I was charging it for whole night.
Cracken6 said:
I removed battery, reconnected after a while, still same problem.
So I tested it with multimeter, it says 2.6V, but fully charged must be 3.8V. Could this be a problem? I was charging it for whole night.
Click to expand...
Click to collapse
I had the same problem a year ago, I tried to remove the battery, charging all night, and other solutions that I found online and no one worked.
Finally I found here in XDA a user with the same problem and his solution was charger the phone with a wireless charger, a friend of mine has one and I put the phone to charge and after a few minutes the screen goes on and the phone was charged, then I press power button and the nexus run again.
Hope this works.
Sorry for my bad English, I'm from Spain.
Good luck.
(I bought a wireless charger in case it happen again)
I don't know anyone with wireless charger. I already ordered a new battery, and then I probably will get wireless charger also. Ty.
But this problem is very weird if you think so.. I think it happened because of many aspects together:
1) Battery was already below 30%
2) I pretty regularly charge phone with USB (won't do it again)
3) It was connected to PC USB in same time.
4) I installed CM12 ROM in same time
So main reason I think is USB, that I restarted phone while it was on pretty low battery and with USB connected.. phone restarted and got invalid voltages and couldn't even boot up or charge phone. I also found an article which says, minimum voltage, when phone battery has 0%, it's 3.0V, so I was below that.. it just screwed everything and battery died. Well, I am not sure for 100% that it's battery fault, but I hope so, I really love my N4 and still wanna use it for long time, I hope it's not dead phone, just a dead battery. Lets see! I will update this thread , when I get my new battery (less than month probably).
Sorry, my english is also not perfect. I am from Latvia.
I was playing when it happened to me. The phone was very very hot and the battery was around 70%. When I put in the wireless charged and I can reboot the phone the battery was at 65%, so it had charge but the phone won't boot.
I charge my phone almost every day, sometimes with AC, others with USB (plugging to PC) or wireless that depends of my needs
I hope you can fix it. Good luck.
Btw. Do you know if battery charges with wireless charger, if it's removed from the phone?
Don't think it does, since the receiving coils for wireless charging are located just behind the glass back.
Flipz77 said:
Don't think it does, since the receiving coils for wireless charging are located just behind the glass back.
Click to expand...
Click to collapse
The battery will charge with a NCF Charger
Major Issue Google
This "Nexus SOD" issue is showing up on many sites across the Internet. I have multiple "Nexus" devices including 2 Nexus 4, 1 Nexus 5, 2 "Nexus 7 2013". It suddenly started out of the blue with one of my Nexus 4 phones. Symptoms included rapid battery discharge. I am using Lollipop 5.1 on all devices. There are many claims as to the cause, Hardware Motherboard, Power Button etc. Others claim it is "Software Related" or App Related. The problem effects Nexus 4 and Nexus 5 phones. I have ordered a new motherboard for my nexus 4 device and see if that makes a difference.
This problem should warrant a "Major Android Lollipop Crisis Team" by Google to investigate the cause and let us know what it is and what Google is doing to solve the problem before moving to announce "Android M". This issue needs to brought up and actively pursued at the upcoming "Google I/O Conference" by the strong Android Developers Groups to press for "Formal Action"
charging method
Cracken6 said:
I have tried that many times. Nothing. It's bootloader screen, but I can't get there. Nothing happens. If I keep holding volume down+power it just keep blinking once every ~10 seconds, same if I hold just power button. If phone is not connected to charger, there are no blinks at all.
Click to expand...
Click to collapse
I had this problem a long time ago and my fix worked for me after doing a little research it seems like this is a case called battery total discharge. The fix was simply to charge your phone using the wall adapter that came with your phone (I still use my old apple cube wall thing) and to wait for the red light to appear then wait about ten minutes before trying to reboot.
I just got new battery . But it looks the same.. phone doesn't boot up.. same red light blinks once.. so.. its my phone is dead? I can't believe that...
When I connect to PC usb, there are unrecognized deviced called "QHSUSB_DLOAD".
Maybe this video will help you: Oh I´m not allowed to post links until now.
Just search for: - Nexus 4 "red light of death" fix - at youtube.
Hope it will help
AndRe5575 said:
Maybe this video will help you: Oh I´m not allowed to post links until now.
Just search for: - Nexus 4 "red light of death" fix - at youtube.
Hope it will help
Click to expand...
Click to collapse
I have checked all kind of videos there. Also that one. Most of these cases are related to battery, but it seems in my case it isn't. I just searched for QHSUSB_DLOAD unrecognized device, all posts says it means phone is bricked... But cmon, how? I installed CM12, successfully, without any errors, then just restarted phone, and its dead...
Cracken6 said:
I have checked all kind of videos there. Also that one. Most of these cases are related to battery, but it seems in my case it isn't. I just searched for QHSUSB_DLOAD unrecognized device, all posts says it means phone is bricked... But cmon, how? I installed CM12, successfully, without any errors, then just restarted phone, and its dead...
Click to expand...
Click to collapse
Did u try booting the phone without battery by connecting to wall charger and what about flashing stock ROM via PC
Also check that the power button works
This case should be solved
as9333 said:
Did u try booting the phone without battery by connecting to wall charger and what about flashing stock ROM via PC
Also check that the power button works
This case should be solved
Click to expand...
Click to collapse
Just tried booting without battery, and connecting to wall. Same - red light blinks once, after I hold Power button or Power+Volume down for about 15 seconds. If I keep buttons pressed, it just repeats every ~15 seconds.
Power buttons works fine.
After I checked that Device manager thing in google.. it looks very bad.. phone is dead.. probably need to change motherboard. I am just shocked, how this could happen... I didn't receive any errors during CM12 installation. Phone just instantly died after restart.
Let me start from the begining.
So the other day I plugged my phone into USB in order to charge it (I had to keep it close to me hence why I didn't plug it into the wall charger). The phone was charging, showing up as a media device on the lappy, etc. I was doing stuff on the computer then I heard it vibrate so I went to see what it was. The blue notification light was on (facebook notification most likely) and when I pressed the Menu button the screen didn't come on. I also tried the Power button but same thing. So I decided to restart the phone. Since then, it hasn't turned back on.
I tested the battery in another device and it's working perfectly fine. Neither recovery nor download mode work. I tried to do some of the tests people recommended for sudden death, like plugging it into usb and leaving it for a while, trying to kick start it (putting battery in while holding the recovery buttons) - you name it, i've done it. I even went to the lengths of taking off the back cover to see if theres any crap that got in there, maybe a loose connector, anything burnt - nothing. Unfortunately, I don't have a multimeter to see if there is a charge running through the board. Looks like sudden death to me, the only thing is - I rooted the phone on the 1st day I got it and I don't live in the country where I bought the phone so sending it over for warranty repairs would be a pain in the ass. What can I do? I would greatly appreciate your help, if you manage to help me fix my baby, I will ENSURE to send you a donation for a nice, big, cold beer (or maybe a few).
Looking forward to any answers! I really need my phone, I use it for work.
It seems like a hardware issue... you need to take it to a local store to scan it's hardware.... maybe something gone wrong while charging which made something be destroyed inside it..... hope its not the motherboard.....
it happens sometimes, when charging current fluctuate, it destroys the charging circuit and in result it damage the whole current circuit, local repair shop can solve the issue.