Hello, I suddenly stopped booting Android from MAGLDR.
Here's a sample you have any advice on solving this problem?
http://youtu.be/Oprz1CtMmF8
Recovery and boot lasts long enough, I also tried TASK29 and other things to clean up the phone, but the result is the same, just hope it's not worn ROM
what if you try to boot recovery or the rom? have you got the "fatal hit" problem?
Windows Mobile ROM work only problem is MAGLDR
I tried all the flash and Recovery and MAGLDR not help it.
But WP7 it works so the problem must be somewhere in recovery because I was working on the phone ROM which I stopped working, so I tried it again flash but will not start, I also tried a different ROM (Sense of Eclipse), but the course is the same.
if a rom breaks and you install a different one, dont forget you need to clerar out the ext partition on teh sd card, and also teh .android folder on the fat32 partition. It could be that something is left there that is preventing the android roms from working.
go into cwm and choose wipe data/factory reset, then flash the rom, then do a wipe data/factory reset again, just to be safe.
tried everything but the boot splash it on my screen freezes and nothing will not boot.
radio? magldr needs a tmous radio, 2.15.50 for example
maybe the system partition is too small.........
I have the EU version and I have radio 2.15 flash
So I have finally boot but where the problem really do not know.
Related
Hello guys!
I don't know what to do anymore...
I used to have wm6.5 Hyperdroid1.7(sd) dualboot, but it began to freeze very often to the point where i could't boot it anymore. Since I had hspl2.08 allready installed, I decided to give the relatively new TyphooN CyanogenMod 7 v2.5.2
(http://forum.xda-developers.com/showthread.php?t=933951)
a try.
Long story short, I had lots of problems with the connection but finally made it to
task29: done (used doloops exe)
radio: 2.15.50.14 done
magldr: 1.13 done
ClockworkMod Recovery v1.3 135M System/44M Cache:
installed with DAF.exe
but when I selected 'AD recovery' in magldr it came up with the
1FATAL HIT 1 error. (worked one time when I left the battery out for 25 min, but never again)
So I decided to do everything over again, task29 etc ....
Some problems occured where I had to plug out the phone because it got
stuck in flashing process of task29/radio/magldr.
And now, nothing works, I can flash radio and magldr, but it does'n seem to affect anything. When I boot I just see just the white htc screen.
Tried to flash stock HTC-wm6.5-rom (with both bootloaders) but it gets stuck @ 8% and gives the wrong comand error.
So please help me, 2 days without a phone (so far ...)
daniel
U UNPLUGGED IT!
Try a task29 .. just a task29 with a compatible radio
Once its done go into the bootloader.. if you get this far flash MAGLDR
If and once MAGLDR boots up then your good to go with Android NAND/SD or WP7
Okay,
I task29'ed it with the 2.15... radio and it seemed to work again.
But I flashed with a nand android and when I booted again:
Booting Android from NAND
ANDROID LOAD at numbers
yaffs2 part is /boot
Load zImage
Load initrd.gz
[K] .. numbers
Load done!
1EFATAL HIT 1
*stuck*
may be relevant:
when I flashed the android it did not reboot automatically.
so i pressed the red reset button on the back.
thedangeroiusd said:
Okay,
I task29'ed it with the 2.15... radio and it seemed to work again.
But I flashed with a nand android and when I booted again:
Booting Android from NAND
ANDROID LOAD at numbers
yaffs2 part is /boot
Load zImage
Load initrd.gz
[K] .. numbers
Load done!
1EFATAL HIT 1
*stuck*
may be relevant:
when I flashed the android it did not reboot automatically.
so i pressed the red reset button on the back.
Click to expand...
Click to collapse
That's an android nand issue..prob kernel related... since you used the DFT android flasher it should've restarted... either try again with the same rom or different rom OR use clockwork recovery... i personally use CWM recovery.. since it has more options like installing from zip and backup/restore entire nand build to the sdcard
also note magldr mass storage .. some people say it corrupts transfer so to safe use card reader just incase when transfering
Sent from my HTC HD2 using XDA App
Ok lets try this Remove your SD card Save only necessary files that you need to your computer. Next Format the SD card leave it out.
I would erase the task 29 and MAGLDR and partition and ROM files from your computer and reinstall (possible file corruption)
Do a Task 29
Install MAGLDR 1.13
Once you install MAGLDR let phone reboot and hold power button to boot into MAGLDR
Choose option 5 and load your partition
Next reboot into MAGLDR again and got to option 8 you will want to find wipe data/factory reset and also wipe dalvik cache.
Now if you are flashing via CWM you should have the build on the SD card so now is the time to put SD card back in and reboot into MAGLDR you can then flash the rom. If you are flashing DFT put card back in reboot phone and enter bootloader and flash DFT.
Hope you get it working please read carefully...pm if you are really stuck.
The ONLY thing you are going to flash via MAGLDR option five is your partition...Did you flash the radio via MAGLDR if so that may be your problem?
If that dont work try this:
Try and use a task29 tool provided here http://forum.xda-developers.com/show...3&postcount=19 . Extract it and run it properly ( with phone in bootloader mode ) and perform the task 29. Then flash a radio version which you can find it here http://forum.xda-developers.com/showthread.php?t=611787 . ( I suggest 2.15 )
My suggestion is to go to bootloader-tricoloured screen ( NOT Magldr ). Flash a good radio version and afterwards go back to tricoloured screen of the bootloader in order to flash a Windows Mobile ROM ( preferably a STOCK one ). Forget about NAND ROMs until you will be sure what your problem is.
PS : Read here for more information http://forum.xda-developers.com/showthread.php?t=609477
Hi
I have a big problem and don't know what is wrong
I was using ultimate droid on nand on my hd2,than i decided to flash shiftpda rom v33 from boyPPC and the problems started. i installed it from my sd card using cwm and when phone rebooted first time magldr said something about missing kernel file. then i tried to flash it again,did task 29 several times,installed magldr and everything again. but it kept saying about missing kernel file. and when i try to install it again cwm says 'installation aborted'. so i decided to flash it from pc with daf.exe. installation was successfull,but phone just reboots over and over again... looks like it will never stop rebooting. dont know what to do please help...
can it be due to wrong radio?
zurjap said:
Hi
I have a big problem and don't know what is wrong
I was using ultimate droid on nand on my hd2,than i decided to flash shiftpda rom v33 from boyPPC and the problems started. i installed it from my sd card using cwm and when phone rebooted first time magldr said something about missing kernel file. then i tried to flash it again,did task 29 several times,installed magldr and everything again. but it kept saying about missing kernel file. and when i try to install it again cwm says 'installation aborted'. so i decided to flash it from pc with daf.exe. installation was successfull,but phone just reboots over and over again... looks like it will never stop rebooting. dont know what to do please help...
Click to expand...
Click to collapse
Can you explain the exact steps you made to install this Rom?
well i will explain what am i'm doing right now. i run task 29 and installed radio 2.15.50.14. after that i installed mgldr 1.13. and on mgldr booting screen it said "sd open kernel failed". after that mgldr menu appears. then i choose usb flasher and install rom from the computer. it says installation successful and phone reboots. after that i see mgldr booting screen and everything looks just fine,then i see HTC screen and phone reboots again...and again and again and again. if i will just put the phone on the table it will just keep rebooting forever ((( am i doing anything wrong? i shouldnt because its not the first rom i am installing...and what does that "sd open kernel failed" message mean??? (
1) First of all, boot into MAGLDR and go to services (option 10). Go to boot settings, Boot source and make sure Android from Nand is selected.
2) Unzip the Boyppc v33 package on your computer and install his CWR DAF package that is included with the rom (The boot loops could be due to having the wrong CWR partition)
3) Load CWR and manually wipe data/factory reset, Go into advanced and wipe Dalvik Cache. Once this is done try and reinstall the V33 zip that you said you had already copied to your SD card. Hope this solves the problem
I've had the same problem twice now. "sd open kernel failed" i believe is shown in red correct? all i did to fix it was reflash MAGLDR & Clockworkmod Recovery then reflash the ROM.
i wish i knew why it happened but its always when im going from 1 ROM to the next & not just restarting my phone up. im thinking maybe it was just a bad flash or something but the steps above has fixed it for me now both times.
try to install recovery and intall a ron throught ur sd card ... rom that r instaleed from daf r pretty simple but maybe the rom was corrumpted during the download or there's a missing file that's not flashed to ur phone ... i suggest to install recovery and to copy ur rom to sd ...it's much simple than the first way
hello, i have a hd2 leo and had nand android on it with magldr(1.13)
i had to switch rom because i wass bored of the one i had. i changed in the ad recovery my rom to another rom. i just followed all steps correctly but when i start the rom it just hangs on the rom load screen... when i try another rom they stuck at the load screen and then reboot the phone.
when i try to go in the hspl to use task29 it hangs at 0% when i try task29
when i use the usb flasher in magldr to task29 it it doesnt see its connected.
i cant go back to my default rom womo 6.5
cant start the rom
cant change eveything
please help me, and if i have a new rom how could i clean my sd card from all the files that are on it?
please help me
You don't use the usb flasher in magldr to do a task 29. You must do task 29 from bootloader (Tri-color screen. turn the device on while holding the volume - button down)
It is possible that you don't need to do a task 29 anyways though.
If you still have magldr, then keep it and don't do a task 29.
You probably just have to re-flash CWR with a different partition layout.
What nand rom did you have before, and what rom do you wish to flash now?
i tried also the tri color screen but it stucks at 0%
how do i reflash cwr with a different partition layout?
and i used all kinda roms and they all say the same
but those i tried:
http://forum.xda-developers.com/showthread.php?t=733649
http://forum.xda-developers.com/showthread.php?t=1264828
http://forum.xda-developers.com/showthread.php?t=1298188
btw i have magldr v1.13
cwm 3.0.0.5
If you don't do a "wipe data / factory reset' in cwm, the next rom rarely boots.
enter cwm and do the reset, see if it helps. The comment above about partition size is the next most common reason.
as for "hangs at 0%",,, does it say "2.08.hspl" in bootloader?
hello, i always do wipe data factory reset and also cache
it says:
Code:
pb81100 HX-BC
spl-2.08.0000 8g XE
microP(led) 0x05
MicroP(touch) 0x30
EDIT; i tried to update the tri color screen to 2.08 HSPL and now i have 2.08.Hspl
but it still doesnt work
Edit2; now i did a task29
okay, so i changed my hspl to 2.08 it was 2.0800000
i did a task29
formated my sd to fat32
i reinstalled my magldr v1.13
i reinstalled my clockwordmod 3.0.0.5
and i tried to launch a rom and it stucks to the first screen (a girl with htc on it)
then i tried another rom ofcourse i wiped all my data/factory also stucked to the first screen (nrg z energiz)
what am i supposed to do now because it just dont wanna work.
change back to winmo 6.5? and then again flash to nand?
please someone help me i updated to hspl2.08
installend stock winmo 6.5
reinstalled magldr 1.13 and clockworkmod 3.0.0.5
tried to boot a rom and still doesnt work
please help me please
pleaseee help me i m still paying for my phone pleasee help mee
iefen said:
please someone help me i updated to hspl2.08
installend stock winmo 6.5
reinstalled magldr 1.13 and clockworkmod 3.0.0.5
<----------->
tried to boot a rom and still doesnt work
please help me please
Click to expand...
Click to collapse
what did you do <-------> ? because you dont mention flashing any rom, just skipped straight from reinstalling magldr and cwm to 'tried to boot'
What partition size did you flash? what rom did you flash?
lots more details please,.
samsamuel said:
what did you do <-------> ? because you dont mention flashing any rom, just skipped straight from reinstalling magldr and cwm to 'tried to boot'
What partition size did you flash? what rom did you flash?
lots more details please,.
Click to expand...
Click to collapse
I didn't flashed anything, In the video I saw the man didn't flashed after installing cwm
Partiton no one told me about partitions so I didn't made one
I can't flash recovery. When I tried flash recovery then phone is stuck and flasher on PC finished with error. I tried flash WM65 and after flash CWM again, but nothing. Also tried task 29.
Any ideas?
Does it get stuck in the same place every time?
hengsheng120 said:
Does it get stuck in the same place every time?
Click to expand...
Click to collapse
yes it is
help plz! anyone had issue like me?
could it be a corrupted ROM file? have you tried other ROMs?
mengfei said:
could it be a corrupted ROM file? have you tried other ROMs?
Click to expand...
Click to collapse
rom file is ok, i tried different versions of cwm, but nothing. when i flashing cwm, phone is stuck (like on screenshot)
sequence;
first check your device if it is 2.08.HSPL, and format your sdcard ext3 or ext4 and 1gb. insert it to your device.
1. task29
2. radio rom 2.15.50.14
3. magldr 1.13
4. recovery 5.0.2.6
5. clear cache and dalvik cache.
use this tool www.mediafire.com/?2qz0xa7xfxney47
and use this radio ; www.mediafire.com/?1th8o158r2t6dba
powerofthink said:
sequence;
first check your device if it is 2.08.HSPL,
1. task29
2. radio rom 2.15.50.14
3. magldr 1.13
4. recovery 5.0.2.6
use this tool www.mediafire.com/?2qz0xa7xfxney47
and use this radio ; www.mediafire.com/?1th8o158r2t6dba
Click to expand...
Click to collapse
Yeah, for once I give a +1 to Task29, although it isn't really necessary most of the time. Can you flash a stock ROM via the SD card? You said that you tried to flash WinMo then CWM again, but you didn't say whether or not it actually worked.
powerofthink said:
sequence;
1. task29
2. radio rom 2.15.50.14
3. magldr 1.13
4. recovery 5.0.2.6
use this tool www.mediafire.com/?2qz0xa7xfxney47
and use this radio ; www.mediafire.com/?1th8o158r2t6dba
Click to expand...
Click to collapse
powerofthink I've tried it, but nothing.
May be this issue becouse i have bad blocks?
Nigeldg said:
Yeah, for once I give a +1 to Task29, although it isn't really necessary most of the time. Can you flash a stock ROM via the SD card? You said that you tried to flash WinMo then CWM again, but you didn't say whether or not it actually worked.
Click to expand...
Click to collapse
WinMO work fine, but CWM still not working, stuck, stuck, stuck...
1) flash official WM6.5 ROM
2) task29
3) magldr
4) cwm (there phone is stuck)
sequence is important!!!. and also it depends on your android rom.
i hope you dont have any other hardware problem.
powerofthink mate, i know how flash hd2, and i know all sequence. I flash my hd2 many time, but one day i have problem with CWM... I hope we are solve this problem
emuleq said:
WinMO work fine, but CWM still not working, stuck, stuck, stuck...
1) flash official WM6.5 ROM
2) task29
3) magldr
4) cwm (there phone is stuck)
Click to expand...
Click to collapse
Mmm..
Just checking
1. have you checked that you have 2.08.HSPL installed? (power on with Volume down)
2. Have checked that installation of Radio_Leo_2.15.50.14 was successful?
3. No problems with flashing the MAGLDR? (Do you get the menu when you press and hold POWER?
4. Did you flash the 250 Mb version of recovery succesful? (Recovery_v1.3_250M.zip)
Please note that as soon as you performed a DAF flash in between, your Recovery does not work anymore.
My reccomendation is that you perform all these tasks using HD2-Tool which is absolutely brilliant. If it doe not work tryu again from the start. (try it without SIM card and SD Card in your phone till you get Recovery working)
(I did this when I bricked one of my 2 HD2's, and was able to get it up and running again)
Good luck!!
strange that winmo is running fine, how about giving clk a try.
Have u tried to flash stock WM 6.5?
:victory:****** Solved *******
Hi, thank you for all of your help and assistance.
It was all down to selecting the correct partitions (and me getting over enthusiastic in flashing roms and not reading FULLY on how and what partitions are required)
I have used HD2 Nand toolkit, and partitioned MAGLDR, then partitioned SD card within Clockworkmod.
Thank you all again for pointing me in the right direction...
Good Evening All,
I am sorry if this has been covered. I have searched the forums but cannot find an answer.
I have read all the FAQ and How-to's.
I am not an exact newbie, I have owned a HD2 before (about 2 years ago) and could install all sorts of different roms (including NAND)
I have Installed my Radio 2.15.50.14
I have installed HARD SPL 2.08
I have Installed MAGdlr 1.13
I ahve installed clockwork mod recovery 1.3 with 400M
Copied rom to root of SD Nexus HD2 jellybean v1.2 [dataonext]
and I have installed Nexus HD2 jellybean v1.2 [dataonext]
this installed fine,
I then decided to try another,
I downloaded QSEA_JB-MUSIC EDITION_V1 and placed on root of SD,
I booted into Magldr, then into clockwork mod
from here i wipe data, and factory reset,
wipe cache partition
and wiped delvic cache.
Then i install zip from sd card QSEA_JB-MUSIC EDITION_V1
when this is done,
It asks me to reboot,
Then it stays on the boot screen, and the rom does not load.....
I can restore the back up from the original rom install. but whatever rom I install (from Nand rom downloads) none of them install...
Please help...
Matt
matt_tee said:
Good Evening All,
I am sorry if this has been covered. I have searched the forums but cannot find an answer.
I have read all the FAQ and How-to's.
I am not an exact newbie, I have owned a HD2 before (about 2 years ago) and could install all sorts of different roms (including NAND)
I have Installed my Radio 2.15.50.14
I have installed HARD SPL 2.08
I have Installed MAGdlr 1.13
I ahve installed clockwork mod recovery 1.3 with 400M
Copied rom to root of SD Nexus HD2 jellybean v1.2 [dataonext]
and I have installed Nexus HD2 jellybean v1.2 [dataonext]
this installed fine,
I then decided to try another,
I downloaded QSEA_JB-MUSIC EDITION_V1 and placed on root of SD,
I booted into Magldr, then into clockwork mod
from here i wipe data, and factory reset,
wipe cache partition
and wiped delvic cache.
Then i install zip from sd card QSEA_JB-MUSIC EDITION_V1
when this is done,
It asks me to reboot,
Then it stays on the boot screen, and the rom does not load.....
I can restore the back up from the original rom install. but whatever rom I install (from Nand rom downloads) none of them install...
Please help...
Matt
Click to expand...
Click to collapse
1-Why? Use the HD2 NAND Toolkit to partition your system according to the developer.
2- Never reboot directly from the "reboot now" option of amarullz's installer. Instead, uncheck the "reboot now" option, click finish and reboot manually from CWM.
(The reboot option somehow makes your rom not boot, at least that happens to me every time)
Marvlesz said:
1-Why? Use the HD2 NAND Toolkit to partition your system according to the developer.
2- Never reboot directly from the "reboot now" option of amarullz's installer. Instead, uncheck the "reboot now" option, click finish and reboot manually from CWM.
(The reboot option somehow makes your rom not boot, at least that happens to me every time)
Click to expand...
Click to collapse
Thanks,
I will give it a go!
Have already downloaded toolkit, and just watching the video on how to use...
Matt:fingers-crossed:
So, do I just use Magldr to partition and don't install CWM?
I tried to re-partition with CWM, but lost magldr.....
What am I doing wrong?
Still cannot install NAND rom.
Going to do Task 29 again, where from there??
Thanks for your help and patience...
try the links below, it might help
matt_tee said:
So, do I just use Magldr to partition and don't install CWM?
I tried to re-partition with CWM, but lost magldr.....
What am I doing wrong?
Still cannot install NAND rom.
Going to do Task 29 again, where from there??
Thanks for your help and patience...
Click to expand...
Click to collapse
I don't use magldr, so I am not sure.
But I think you have to "MAGLDR recovery update" first, and then after it finishes you have to "magdlr repartition". Im not sure though.
How do I just install clockwork mod? Without using Magldr?
If I Task29 first,
What's my next step.....?
After Task29 (don't do task29 again) you have to do the following: http://forum.xda-developers.com/showthread.php?p=25781675#post25781675 until you see the "recovery" .. from there, dont continue to flashing wp7, just put your rom on your sd and flash it from recovery. (don't forget to thank the the one who made the thread/guide)
Don't forget to NOT use 300mb, but use the one written on your rom's thread.
matt_tee said:
How do I just install clockwork mod? Without using Magldr?
If I Task29 first,
What's my next step.....?
Click to expand...
Click to collapse
You can't have CWM without MAGLDR. If you've flashed CWM you shouldn't have lost MAGLDR at all, so I don't know what you did wrong. Task 29s are also almost always useless and unnecessary, if a guide says 'task 29' as the first step then usually you can just skip that part. I find that the best guide is the one in my sig, try it out.