Related
Hello,
I have been trying to root my friends HTC Magic following instructions I have found on this and other forums and having no luck.
The phone in question is a vodafone htc magic.
My problem is that the computer does'nt recognise the phone as the drivers don't seem to work for it!
Could somebody please post a step by step guide for Noobs so I can see where I am going wrong!
I rooted my Hero no problems, but the Magic is proving a bit more of a challange!!!!!!
Many thanks,
Iain
You could do what I did which I've summarised below. There's probably more backup steps than is necessary, but you can never be too careful.
There's loads of guides out there with the guides and detail, e.g. http://forum.xda-developers.com/showthread.php?t=519523
but they seem to branch in and out of methods quite a bit. I've added a few links to the pages I used for the detail.
The method I used is the 1 click backdoor, which also disables OTA updates to stop it being closed in the future I think.
First off, I'm a Linux noob and managed okay because the apps are so well thought out, but this is all done at your own risk.
Secondly, your uk Magic Vodafone prob has 32b board, not 32a.
(There's plenty on this forum. Or the Cyanogen one on the Dream forum works for 32b too.)
You can check with extra step by powering off, then on power again while holding back button. Last digits at top tell you the board details. Menu button gets you back.
0) Install the Android USB driver, connect, mount, then disconnect, etc.
http://dl.google.com/android/android_usb_windows.zip
1) Use google to sync all your contacts, etc. to google account so restore is automatic.
2) Use Astro to Backup your apps etc to the sd card
3) Goto wireless settings, mobile networks, apn, select and make note of your vodafone UK APN details (so you can type your 3g settings back)
4) Use USB to copy your SD card to your PC
5) From your phone, Download Cyanogen recovery. Don't run yet.
http://www.ryebrye.com/blog/2009/08/16/android-rooting-in-1-click-in-progress/
( This basically automates the rooting and booting to this recovery image : http://forum.xda-developers.com/showthread.php?t=523558 )
6) From your phone, Download a rom image; the 32b board you prob have in your UK Magic allows you to use 32b ones, I used the Cyanogen one here.
http://forum.xda-developers.com/showthread.php?t=537204
7) Use Astro to move the rom file from \sdcard\download to root of \sdcard
8) Run Cyanogen recovery 1.4 1-click root installed in 5.
Use Backup recovery image
Use Flash recovery
9) Poweroff, home + power to get into the custom recovery image
10) Select Nandroid backup to create new backup (this copies your phone to your SD card)
11) Reboot. Repeat 3 to get the backup of the nandroid folder, and the recovery image created in 7 and 9 onto your PC
12) Run Cyanogen recovery 1.4 1-click root installed in 5 again.
Flash recovery (this makes next boot 'special')
13) Reboot. Poweroff, hold home + power on again.
14) Select WIPE (You did backup your apps and SD card data right?).
15) Then select apply any zip from sd.
Follow instructions to install the Cyanogen rom image you moved to the root of your SD Card in 6 and 7
16) Wait 10 mins or so. The last message about writing root or whatever doesn't explicitly say finished.
17) Reboot.
If you have reboot hang, most people report is because missed WIPE step. Otherwise consult the relevant forum for the Rom you downloaded.
18) Do the new user settings thing. The activation and sync will fail cos you've not got 3G yet.
19) Goto network settings, advanced, APN, type in your vodafone UK APN details (so you can type your 3g settings back)
20) Done
21) If you've got Cyanogen Install the updater from marketplace (search for Cyanogen), or here...
http://forum.xda-developers.com/showthread.php?t=544663
I also installed:
Audio resources unzipped to your SD Card root from the Cyanogen rom pages, this reinstates notifications and ringtones I guess were removed to allow the memory obsessives to keep their phones clean.
SetCPU from this site, to override the default Cyanogen high overclock settings when phone is sleeping.
Cheers
Chris
Hi Chris,
Thanks alot for that, my friend is coming over after the F1 so will give it a go and let you know how we get on!!!!!
Thanks alot for your help!
iain
Hi!
Did you solved the problem, I seem to have the very same problem as you
trying to get cyanogen on my uk htc magic
Hi,
I have been trying to get cyanogen on my vodafone uk htc magic for a few hours now, not even getting close though!
The problem is, i already have the proper 1.6 update which vodafone pushed out a couple weeks back, and now want to root my phone and get cyanogens 1.6 on it. The flashrec application only runs on early versions of cupcake i believe, so my first step was to get that on my phone. (I have been following this: http://wiki.cyanogenmod.com/index.php/Full_Update_Guide_-_MT3G/Magic_Firmware_to_CyanogenMod aswell as trying the guide on this forum thread)
When i quickboot the phone and try to install the 1.5 update, it goes all the way through with the progress bar in the top right, then fails right at the end on 'Model ID Incorrect! Update Fail!'. When i reboot the phone it is just as it was before.
I have also tried putting the cm-recovery-1.4.img file on the memory card and installing that from flashboot but that also fails.
Do you have any ideas / recommendations for getting cyanogen on there?
Thanks,
Aaron
[email protected]
Skype: atrout1991
aaron465 said:
Hi,
I have been trying to get cyanogen on my vodafone uk htc magic for a few hours now, not even getting close though!
The problem is, i already have the proper 1.6 update which vodafone pushed out a couple weeks back, and now want to root my phone and get cyanogens 1.6 on it. The flashrec application only runs on early versions of cupcake i believe, so my first step was to get that on my phone. (I have been following this: http://wiki.cyanogenmod.com/index.php/Full_Update_Guide_-_MT3G/Magic_Firmware_to_CyanogenMod aswell as trying the guide on this forum thread)
When i quickboot the phone and try to install the 1.5 update, it goes all the way through with the progress bar in the top right, then fails right at the end on 'Model ID Incorrect! Update Fail!'. When i reboot the phone it is just as it was before.
I have also tried putting the cm-recovery-1.4.img file on the memory card and installing that from flashboot but that also fails.
Do you have any ideas / recommendations for getting cyanogen on there?
Thanks,
Aaron
[email protected]
Skype: atrout1991
Click to expand...
Click to collapse
Is there a solution for this?
I did get this working in the end, was quite a while ago now though...
I am pretty sure that I used the relentless rooter program to get it working in the end, details/download are here:
http://forum.xda-developers.com/showthread.php?t=556200
Aaron
I understand there's a tips and tricks thread that explains things in more detail but how does somebody go from just getting the phone to installing, or even understanding, things like obsidian, onyx, morphing and learning what the basic functions of such programs are.
The question I currently have is concerning flashing custom roms. In the tips & tricks thread, it talks of froyo builds (ex: bionix & frankin-twiz). What is it exactly? From what I understand, it sounds like a mini os that you install onto your device which helps in applying different functions to it, which makes custom roms possible.
I'm currently trying to get http://forum.xda-developers.com/showthread.php?t=845530 to work on my vibrant. Can anybody help a newbie out?
VibrantUser1 said:
I understand there's a tips and tricks thread that explains things in more detail but how does somebody go from just getting the phone to installing, or even understanding, things like obsidian, onyx, morphing and learning what the basic functions of such programs are.
The question I currently have is concerning flashing custom roms. In the tips & tricks thread, it talks of froyo builds (ex: bionix & frankin-twiz). What is it exactly? From what I understand, it sounds like a mini os that you install onto your device which helps in applying different functions to it, which makes custom roms possible.
I'm currently trying to get http://forum.xda-developers.com/showthread.php?t=845530 to work on my vibrant. Can anybody help a newbie out?
Click to expand...
Click to collapse
the link you posted is just to a theme.
to get the theme to work you'll need to be running obsidian first.
so lets see, the easiest way to explain the different versions 2.2, 2.1 1.6, 1.5 and so forth is this...
its pretty much like going from windows 95 to 98 to 2000 to xp to vista and so forth.
our vibrants come with android 2.1, 2.2 is the next version of the os to come out (basicaly like moving from vista to windows 7)
the different roms like obsidian and Macnut and such are just names that the developers gave their roms.
what happens is a developer starts out with a version of android (in the case of Macnut and Obsidian this is 2.2)
and then they add their own modified tweaks and such to it.
and so in the end they get Obsidian which is a modified 2.2
or Macnut which is also a modified 2.2
they differ a bit though as Obsidian is based almost totaly on a leaked version of 2.2 for the US vibrant, where Macnut is based alot on the 19000 version of 2.2 for the european phones.
so when choosing a rom just choose the base you want first: 2.1 or 2.2
then look through the tweaks on a few roms and read some of the thread for that rom untill you get a feel for what makes it unique
you can also just experiment by flashing a rom for a day or so and then switching to a new one untill you find one you like.
Morphing is a way to apply a theme to a rom, this does not generaly change functionality at all, it only changes apearance.
alot of themes are either morphs (you install them using metamorph, which is an app from the market)
or they also come in zip format (which are installed by flashing from recovery)
for the theme you posted you will need to flash obsidian, and then flash the zip for the theme afterwards.
have you rooted your device yet?
thats the place to start, if you need help just pm me or repost here and I'll do what I can.
also, there is a "newbie's guide":
http://forum.xda-developers.com/showthread.php?t=732458
nearblack said:
also, there is a "newbie's guide":
http://forum.xda-developers.com/showthread.php?t=732458
Click to expand...
Click to collapse
lol true true
Before you even want to start with anything, you have to learn what 'rooting' your phone means.
Without root, you won't be able to do any of the above. You might be able to download the programs necessary, but you won't be able to use them.
For ex. Titanium Backup, ROM Manager, etc.
We use ROM Manager to install different ROMs on our phones.
Much to read, my young grasshopper.
OP, I made the Tips/Tricks sticky... would you PM be exactly what you think it lacks? I want to make sure it is applicable to everyone... I thought it was straight-forward, perhaps not.
my phone is rooted. So how do I go about flashing obsidian?
I thought roms were the same as themes? What's the difference?
And just to clarify I understand the tips and tricks thread is sort of the newbies guide but even then theres a lot of terminology that a new user wouldn't understand. I just wanted some basic information that would allow me to transition into the tips and tricks thread more easily.
I appreciate the responses so far
Have you download Rom Manager from the Market? If not, do so.
Then follow the instructions (in the sticky) to flash the recovery (it's the top of the list when you open Rom Manager).
Assuming you did that, you can reboot into recovery, make a backup of your system.. something you can always come back to (a timestamp of your system at that moment).
Download the ROM you want, put it on your internal memory (sdcard/....) NOT in a folder.
Go to Clockwork recovery, choose to insall a zip from sd card... select the name of the ROM and then click Yes to install it.
It will run it's course, then you can just reboot when done.
The first bootup will take a long time (10 minutes probably)... let it boot.... leave your phone alone for like 10 or so minutes after bootup (suggested by Team Whiskey, I never really do this).
It's that easy.
Think of a ROM as an OS... the developers take Froyo (2.2) or Eclair (2.1) and make a lot of tweaks, remove things, add things... basically anything to enhance the user experience.
THEMES are something you flash over a custom ROM... it can change the icons, graphics, notification bar, etc... they are cosmetic. You see in my signature I have Axura 2.0.3 (amazing rom and there is a newer version out) and then I have BlackFroyo (which is the theme) on top of the ROM to change the look of things. Axura has a steel looking notification bar, I much prefer black (hence the theme I chose).
The ONE thing that can be confusing... if you make a backup right now (you have stock eclair), if you flash a froyo rom... you would need to flash either the stock eclair kernel (the download link is also in the sticky) to restore your nandoid backup.... OR, you could just flash another ROM that has a kernel (most do) and you would be good to go too.
And addition to this is to make sure your phone is NOT hardware locked.
To test it:
1) Take out battery from the phone and put it back in again
2) The USB cable plugged into the computer (not in the phone yet)
3) Push and hold down both of the Volume buttons at the same time
4) Plug in USB cable and it should take you into the Download mode.
If it does you are good to go. Just read some about Odin and Stock Android
If it isn't you need to make sure to flash JI6 to your phone (also Stock) onto your phone using Stock Manager. That should fix your hardware locked. Go over the above steps to make sure that is the case.
At this point, I have rooted my device and downloaded rom manager.I believe I have backed up everything after following the directions and I do have the blackfroyo.zip on my sd card and for some reason it won't "go" (although I'm sure there's a step I am missing here, something with obsidian) so that wasn't much of a surprise.
Edit: I noticed I tried to use a theme on there and not the obsidian "OS" (idiot) when I tried the backup thing with rom manager. Where can I download the most recent version of obsidian and/or is axura an acceptable alternative?
VibrantUser1 said:
Edit: I noticed I tried to use a theme on there and not the obsidian "OS" (idiot) when I tried the backup thing with rom manager. Where can I download the most recent version of obsidian and/or is axura an acceptable alternative?
Click to expand...
Click to collapse
Been working on updating the wiki. Please check out http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_SGH-T959#ROMs for the different ROMs currently available.
^^ both are solid. I prefer Auxura *no touchwiz*.... download it from the development section. Place in on the internal (sdcard/ ) and flash it, reboot... I would let the phone chill for awhile then reboot again.... THEN if you want, start messing with the theme. You can see from my signature you and I are similar.
to the OP, I started a noob friendly guide in the Q&A section. Please let me know exactly what you want in there.
Here is a video guide, its kinda old but the principles are the same.
http://theunlockr.com/2010/08/02/how-to-load-a-custom-rom-on-the-samsung-captivate-vibrant/
I have been browsing around and reading on XDA since I got my G1 on release day. I have since upgraded to the MYT3G and now to the Vibrant. I have always used XDA as a source of information for rooting, etc. I don't post very often, but, I would like to throw props out to all the individuals in the thread, this is one of the few threads I have read on XDA that no one got flamed for being a "noob" and asking basic info, the information given was clear, accurate and very helpful. No one pointed to using the search function, everyone just gave good answers. AWESOME
I hope to see more threads like this in the future. Bravo and well done to all.
So I tried installing obsidian 5 and this is what happened. I first put the zip file on my sd card, I did all the necessary prerequisites (I think) using rom manager, flash recovery > vibrant yada yada yada and then pressed install rom from sd card and chose the obsidian zip file. Then the phone starts backing itself up and it finally reaches a point where it says (E: Can't open/sdcard/sd/obsidian_v5_beta.zip (no such file or directory) Installation aborted.
I then try to navigate to the file from the menu but whenever I click the sd file, it just exits, I think it says that no zip file is found or something but when I boot it up normally afterwards, the file is still there.
But the file is within the sd file . . . what am I doing wrong? I tried to fix permissions thinking it was that but no luck.
You probably need to move to the rom to the internal sd card. I thought you're able to add it to the external with the recent update but perhaps not
Sent from my GT-I9000 using XDA App
bellrb19 said:
You probably need to move to the rom to the internal sd card. I thought you're able to add it to the external with the recent update but perhaps not
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
the rom IS on the sd card, unless you mean the memory on the actual phone itself
ROMs go on the root of the internal memory (no folder)... drop it in sdcard/
Also, this was mentioned in Post 8, and in team whiskeys install guide. Please pay attention to details.
oh okay, this whole time I've been thinkin the sd card folder was the root folder. Well I have finally put obsidian with success and now I'm having a difficult time implementing http://forum.xda-developers.com/showthread.php?t=845530. I have downloaded the zip file but I don't understand what "flash it through clockwork recovery" means. It kinda sounds like I should use something in rom manager but I'm not sure, I have tried to reboot into recovery through rom manager with no luck.
I've also tried using metamorph but when i choose the blackfroyo.zip file, it says that the file is invalid and that the theme control file could be missing. Am I doing something wrong here as well?
Thanks for all your help so far, I really appreciate you taking time out of your busy life to help an individual with (what may be to you) simple problems
VibrantUser1 said:
oh okay, this whole time I've been thinkin the sd card folder was the root folder. Well I have finally put obsidian with success and now I'm having a difficult time implementing http://forum.xda-developers.com/showthread.php?t=845530. I have downloaded the zip file but I don't understand what "flash it through clockwork recovery" means. It kinda sounds like I should use something in rom manager but I'm not sure, I have tried to reboot into recovery through rom manager with no luck.
I've also tried using metamorph but when i choose the blackfroyo.zip file, it says that the file is invalid and that the theme control file could be missing. Am I doing something wrong here as well?
Thanks for all your help so far, I really appreciate you taking time out of your busy life to help an individual with (what may be to you) simple problems
Click to expand...
Click to collapse
From where you are now. Make sure the zip file is in the internal sd card, Open rom manager go to install rom from sd card then choose the that file then click ok and CW will do its thing. Also this is only for Obsidian v4.2 and Auxura 2.05. Good luck! Also you should make a nandroid back up first just in case.
G'day. I hate to be posting, especially after that intro video However, I have searched thru the related posts, (everything that has kernel + dalingrin in the title/subject etc) and I can't seem to find anything related to specifically what I need.
Background: Bought nook on ebay from a nice guy who included instructions on how to register and re-root. Took me a hour or two because he didn't include a step. Got it figured out without his help - so I'm not a complete idiot, but I'm out of my realm on this one. I don't do this kind, so please be kind and patient.
I want to install the dalingrin‘s Nook Color Tweak App as I find the volume on my nook repulsing. I need a hearing aid to read their lips, it's that quiet =\ So I am asking for a tutorial basically. I read that it needs a kernel, how do I find the right one, I found threads that had a few kernel downloads but not the one I need from what the red text says. Where do I install it? (is that information included in the download, once I find where it is?) and lastly, once the kernel is installed, do I run the app like I did manual nooter, installing zip, choosing zip, etc?
Thanks for your time.
I haven't played much with kernel yet but do suggest, since the OC (overclocked) kernel created by Daringlin, do search for his name.
AFAIK, the 063011 is his latest work with 5 cpu clock stepping up to 1200MHz along with voltage adjustments and audio tune.
Make sure you get the corresponding for your running ROM, i.e. running off eMMC or booting from uSD.
If I find the link, I'll post.
Other members surely will help you out.
Update: just to clear up a bit, you need to install his apps (NookColorTweak) in order to adjust voltage and audio
azlpeterson said:
, I have searched thru the related posts, (everything that has kernel + dalingrin in the title/subject etc) and I can't seem to find anything related to specifically what I need.
Click to expand...
Click to collapse
Most of the posts I've come across are people complaining they can't get it to work in general or their kernel doesn't work. I need to know how to install it before I can utilize the "I broke it" posts lmao. Thank you though.
You checked here?
http://forum.xda-developers.com/showthread.php?t=1104039
jacjar1 said:
You checked here?
http://forum.xda-developers.com/showthread.php?t=1104039
Click to expand...
Click to collapse
If you read the whole post, that is the link I provided to ask my questions on. I want to know the info on how to install THAT app, including which kernel I need ( it has a few listed in red at the bottom) and how I go about doing that. As I mentioned, I am not incompetent, but I am not familiar with this kind of stuff either. A simple how-to is all I'm looking for from someone who has actually went thru the steps to install this app.
As I mentioned above, you need to identify which category you are falling in.
I believe each version of his (dalingrin's) work, there are 4 different kernels which associate with each of the running ROM.
1. Rooted NC which runs stock ROM (Froyo 2.2)
a. Running off internal eMMC
b. Booting from external uSD
2. CM7 ROM (Gingerbread 2.3.x)
a. Running off internal eMMC
b. Booting from external uSD
The latest version would be the "06302011"
Again, firstly, identify and download the correct file.
Secondly, i do not root my NC but install CM7 ROM on it, so
a. for running off eMMC, put the correct file in the flashable CwM, insert into the NC, power it up, "install zip file from SD card" -> "choose zip file from SD card", then flash it.
b. for booting from uSD, put the correct file into the root folder of the bootable CM7, insert into the NC, power it up, it will automatically detect and install the OC's zip file.
votinh said:
As I mentioned above, you need to identify which category you are falling in.
I believe each version of his (dalingrin's) work, there are 4 different kernels which associate with each of the running ROM.
1. Rooted NC which runs stock ROM (Froyo 2.2)
a. Running off internal eMMC
b. Booting from external uSD
2. CM7 ROM (Gingerbread 2.3.x)
a. Running off internal eMMC
b. Booting from external uSD
The latest version would be the "06302011"
Again, firstly, identify and download the correct file.
Secondly, i do not root my NC but install CM7 ROM on it, so
a. for running off eMMC, put the correct file in the flashable CwM, insert into the NC, power it up, "install zip file from SD card" -> "choose zip file from SD card", then flash it.
b. for booting from uSD, put the correct file into the root folder of the bootable CM7, insert into the NC, power it up, it will automatically detect and install the OC's zip file.
Click to expand...
Click to collapse
I hope I get this right: When I got the NC, I had to reset it to default settings. Registered under my account, then restored it to 1.1, then to 1.2 (which I think is Froyo 2.2 from what I read here. Then I used manual nooter 4.6.16
its not running a boot disk, it was installed straight into the NC, if that makes sense.
So I guess I fall into:
"1. Rooted NC which runs stock ROM (Froyo 2.2)"
And is this the correct link/kernel? http://coachz.inetpro.org/~dalingrin/nook/kernels/063011/
So just install to a boot disk, put it in, install like nooter. Then install the tweak app the same way and all I'm done? Coming from this link: http://forum.xda-developers.com/showthread.php?t=925451 it says " Must be set with an app like SetCPU unless running CM7" Is this an app I download from the market, correct?
I'm sorry, just trying to make sense of all this, and I appreciate your help.
I guess you would need the third one from your link (Froyo 1.2 ... emmc)
Create a flashable uSD, drag the zip file on, put the uSD in the NC, then install/choose zip from SD card.
Keep all of your fingers crossed.
I wish you luck.
P.S. the app is Dalingrin NookColorTweak.
P.S. since you rooted the NC, you should get full access on the Market, do search for the NookcolorTweak app first and see if you can find it before flash the kernel.
azlpeterson said:
G'day. I hate to be posting, especially after that intro video However, I have searched thru the related posts, (everything that has kernel + dalingrin in the title/subject etc) and I can't seem to find anything related to specifically what I need.
Background: Bought nook on ebay from a nice guy who included instructions on how to register and re-root. Took me a hour or two because he didn't include a step. Got it figured out without his help - so I'm not a complete idiot, but I'm out of my realm on this one. I don't do this kind, so please be kind and patient.
I want to install the dalingrin‘s Nook Color Tweak App as I find the volume on my nook repulsing. I need a hearing aid to read their lips, it's that quiet =\ So I am asking for a tutorial basically. I read that it needs a kernel, how do I find the right one, I found threads that had a few kernel downloads but not the one I need from what the red text says. Where do I install it? (is that information included in the download, once I find where it is?) and lastly, once the kernel is installed, do I run the app like I did manual nooter, installing zip, choosing zip, etc?
Thanks for your time.
Click to expand...
Click to collapse
If your'e running cm7 the correct kernel has been appearing in the last few nightlies, though I recommend you wait until tonight to install it.
If it's stock you're using.. well... why?
Guide(/essay) removed as I don't have this phone anymore, so can't update or change the guide with accurate information, which I haven't tested on my own device first Thanks for all the help from others.
..
..
Restoring tpt functionality
..
These are good explanations, very thorough.
I've picked up on a few things that could be added/edited.
1.) Gen 2 is a newer version of the radio firmware, as well as the different memory map
2.) Add Amon Ra Recovery as an alternative to CWM, I know it's not very popular but I find it good for partitioning.
3.) Add link to Mr Pigfish, https://market.android.com/details?id=com.apedroid.pigfish&feature=search_result
4.) On the Flashing ROM's section, I'd also add 'Go into Mounts and Storage and Select Format System'. Not needed, but recommended for the cleanest installation and hopefully fewer problems down the line.
5.) There's the CM7 Converter thing for people to use CM7 on a Gen 1 phone. It can be flashed via recovery.
6.) Add TPT link for Ginger Stir Fry (Over on MoDaCo) since it's popular.
7.) Remove or clarify 'Gen does not matter' under the TPT section, a few may take this that Gen 1 ROM's can be flashed on a Gen 2 device :/
8.) Put warnings/important things in big scary red writing.
9.) Bold and underline the headings e.g. Gen 1/Gen 2, TPT, Root etc.
10.) Personally, I'd say that the Firmware is more similar to the BIOS than Recovery. Recovery is probably most similar to Windows Recovery Environment.
I'm glad you explained what recovery is since it's a bit annoying when people don't know and don't bother to Google it, hopefully they'll read this and understand. I hope you find my comments constructive.
Partitioning your SD Card.
Why?
To create an EXT Partition for A2SD (Not to be confused with the Froyo Apps2SD).
Why do I want this?
For more space on the phone's internal memory and to allow certain apps like widget's to reside on 'internal' memory which may not be available if they were on the FAT32 Partition used by the Froyo Apps2SD method.
How do I do this?
There are a few ways to do this, I found this method the best. I'd recommend doing this before flashing a ROM with a full wipe to avoid issues.
1.) Create a full Backup in Recovery in case something goes wrong
2.) Mount the SD Card on Windows/Linux/Mac
3.) Copy the contents of the SD card into a folder on Windows/Linux/Mac
4.) Download Amon Ra Recovery - Gen 1 Gen 2 Ensure you download and verify you download the correct version. Flashing the wrong version i.e. Gen 1 on a Gen 2 will cause a lot of problems.
5.) Flash it with your existing recovery e.g. Clockworkmod
6.) Go back to Advanced > Reboot Recovery
7.) Scroll down to Partition SD Card
8.) Select Partition SD
9.) Swap Size 0 MB EXT Partition Size 512 MB/1024 MB - depends on the size of your SD card and the number of apps you have.
10.) Press Home to Confirm. ALL Data on your SD will be erased.
11.) Press back and select EXT2 to EXT3 for the best compatibility with A2SD scripts.
12.) Select USB-MS toggle
13.) Drag and drop the ROM you want to flash on your SD
14.) Disable USB-MS toggle.
15.) Flash .zip from SD Card.
16.) If you intend to use CM7 download S2E from the Market to enable A2SD. Tick the first two boxes in the app. Alternatively, if you want to ensure you have enough space for when the Google Backup & Restore happens I've uploaded the APK of S2E to install BEFORE you flash Gapps.
Enjoy.
BTW are you going to post the guide that you wrote in the first post on MoDaCo? It'll get more views there and subsequently be of more use.
If you have any further questions you can find me on MoDaCo with the same username, I'll do my best to help. I'm not a developer either for that matter.
Hello, hedgepigdaniel from modaco here.
Nice guide, I have a couple of suggestions/comments
I don't know if you are aware, but Gen2 blades do have TPT, they just use a different file format (image.bin rather than the .img and .mbn files). There are not as many custom layourts and such around, but I have just put one up for the purposes of unbricking. For that reason, I don't think its a good idea to recommend flashing via windows as protection from a brick anymore (especially because windows flashing goes horribly wrong every so often).
In the rooting section, why don't you link to kalt kaffes modified z4root instead - since it can root Gen2 blades aswell. For Gen2 blades, ROM manager from market is the the easiest way to install recovery.
I've written an unbricking guide in the last few days (that's where the Gen2 TPT is). You are welcome to make use of that if you like.
Glad I finally got enough posts to post in the development section...
..
TPT is not able to change the lowest level firmware file - partition.mbn. If you try to flash a TPT with a different partition.mbn then it just wont flash. You need windows to change the entire firmware. What wbaw has done (and I just repackaged his work as "custom") is create a mixture of files from Gen1 and Gen2, partition.mbn and the few files that have to match from Gen1, and the rest from Gen2. This makes it possible to TPT a Gen1 phone to a mixture that for all intents and purposes is Gen2. wbaw's TPTs can't be flashed to a real Gen2 phone because they have a Gen1 partition.mbn, but It would be equally possible for someone to make the opposite of what wbaw has made - a image.bin TPT with a Gen2 partition.mbn and co and Gen1 everything else (or just with a different partition layout), but no one has yet done so (and I haven't taken the time to work out how). So right now windows is the only way to go back to Gen1 from Gen2, but it doesn't have to be. More to the point, it isn't the only way to re-flash real Gen2 firmware, because I've now put a Gen2 image.bin in my unbricking guide. That's why I wouldn't recommend that people flash anything via windows with the aim of avoiding a brick.
You can use this tool by fonix232 to convert between multi-image TPTs and image.bin TPTs. If you start out with the multi image files from stock Gen2 firmware then you can create a image.bin that will flash on stock Gen2 phones as I have done.
EDIT: jsut to clarify, It's still fine to flash via windows as per my guide if you want to be able to flash all the TPTs that are out there on forums now, or to repartition or enable fastboot, its just not necessary as a safety measure.
Not sure if this is the best idea for 'n00bs' but there's an excellent partition tool for custom partitions.
http://android.modaco.com/topic/337...ol-windows-only/page__p__1672185#entry1672185
By Ricardopvz
It works with the Windows Flasher and the TPT's.
Instructions for use:
1.) Open the program
2.) Drag the sliders or enter values for the partition layout you want
3.) Press Create files
4.) Open the TPT .zip
5.) Navigate to the directory with "partition_zte.mbn" and "appsboot.mbn"
6.) Replace the existing "partition_zte.mbn" and "appsboot.mbn" with the new ones.
Done.
Also, add How to flash the Gapps package/Where's my Market gone and difference between Stable, Nightlies etc. under the CM section since some people can't be bothered to Google it.
1.) Place the gapps file that you downloaded on the root of your SD Card
2.) Reboot into recovery
3.) Select Flash .zip from SD Card
4.) Confirm
5.) Reboot
6.) Done
What's the difference between Stable, Nightlies, Experimental and Alpha?
Stable versions are those where all known issues have been addressed and resolved. This version is for everyday use.
Test / RC versions are similar to the experimental versions, but are in the final stages of testing before being "stable". There may be a few bugs left, but this version is usually stable enough for everyday use.
Experimental / Alpha versions are those where new features are being added, modified, and tweaked, and there are known bugs that are being worked on. This version is for beta / alpha testers.
Nightly builds are daily compiled builds from source. This version therefore has the latest bleeding edge features & tweaks, but it is also the mostly likely to have bugs and issues.
Click to expand...
Click to collapse
CyanogenMod Tips/Solutions, some from the CyanogenMod Wiki here.
It's slow!
Remove stock launcher "ADW". It slows down the homescreen badly.
Recommended: "Launcher Pro" or "Gingerbread Launcher" from Market.
Omg I flashed CM7 and now I don't have Market!
You need to install the Gapps zip. Sign into your account on the First Time Setup screen and Market will activate
My Wi-Fi doesn't turn off/it's draining my battery!
The workaround for Wi-Fi sleep policy that doesn't seem work is download Green Power from the Market if you want your Wi-Fi off when your screen turns off.
Help, Nightly 1xx doesn't work properly/There's a bug!
They're nightlies, sometimes they don't work properly. Use the recommended Nightly from the Wiki Page or another ROM. Also, refer to the CM7 thread on MoDaCo linked below for possible fixes/workarounds.
I don't know what nightly to choose!
First check the CyanogenMod Wiki listed above the CM7 thread on MoDaCo here.
Read the last five pages on that thread for up to date info and feedback on the latest nightlies.
If you still don't know then post in the CM7 thread. Don't create an entire new thread to ask that question please.
Hi im trying to root my friend's blade. I cant find the file to root. Could you be kind to show the link please?
Guide to Rooting:
Enable USB Debugging:
Settings-->Applications-->Development-->USB Debugging (tick)
Install this Apk:
Install Astro File Browser from the market. https://market.android.com/details?id=com.metago.astro
Download the file on your computer, then copy it across to somewhere on your phone
Browse to that somewhere and click on the file. Open app manager and click install.
After installation, click open.
Tell it to do Permanent Root
Wait for it to reboot
Done.
Sent from my X10i using XDA App
teddymild said:
Hi im trying to root my friend's blade. I cant find the file to root. Could you be kind to show the link please?
Sent from my X10i using XDA App
Click to expand...
Click to collapse
I'd suggest you use the TPT method here since the process would be quicker than rooting it manually etc.: http://android.modaco.com/topic/337798-gen1-to-gen2-tpt-upgrade/
This will root the phone, install Clockworkmod recovery and put on a new 2.3 ROM as well. I'd suggest you use the Ginger Stir Fry one on that page.
I think z4root would work as well if you don't want to carry out the TPT method.
How's the guide going?
Thank you. I'll try it.
k0zmic said:
I'd suggest you use the TPT method here since the process would be quicker than rooting it manually etc.: http://android.modaco.com/topic/337798-gen1-to-gen2-tpt-upgrade/
This will root the phone, install Clockworkmod recovery and put on a new 2.3 ROM as well. I'd suggest you use the Ginger Stir Fry one on that page.
I think z4root would work as well if you don't want to carry out the TPT method.
Click to expand...
Click to collapse
Sent from my X10i using XDA App
This thread dead?
..
It would be nice to take this thread further.
Hi
An FAQ thread for Blade users.
Credits to StevenHarperUK
This is a guide to cover most of the common problems.
It contains some words like ROM and Build.props and RECOVERY. PM me if u can't understand anything
----------------------------------------------------------------------------
--I want to know whet generation of phone I have
[GEN1] or [GEN2]
There are now 2 Generations of the ZTE-BLADE device.Each have a different style memory
layout.[GEN1] BLADES use the baseband of 0x02A00000 and can use all of the ROMS made [GEN2]
BLADES use the baseband of 0x02600000 Trying to install a GEN1 ROM onto a GEN2 device will
brick it. GEN1 devices can be recovered and converted with a TPT
--How to find out what BLADE you have (GEN1 or GEN2)
You need to install this app Ask Mr Pigfish When you run the APP the first line will be
Mr.Pigfish says you have a Gen1 model
--How do i root my phone
ZTE Blades with Android 2.2 or lower can be rooted using z4root mod. If it doesnt work, or you have 2.3
blade there is a How to root thread in the Blade Android Development section
--How do i install a rom
-Download the Rom
-Download GoogleAps (CyanogenMod only)
-Backup your data using software like Titanium Backup
-Install clockworkmod recovery from Rom manager
-Boot into recovery (Power + volume down)
-wipe data/factory reset
-wipe cache
-install zip from sdcard option ---> select your rom
-do the same for GoogleApps
-reboot (first boot takes a while)
--The Custom ROM wont Boot Properly. Gets Stuck at the Animated/non-animated boot
screen.
This can be because of a few things You have installed a new ROM and need to clear you cache
and factory reset You installed a Theme or patch without letting the new Custom ROM boot
first The ROM you flashed was damaged when downloading - check with md4sum - re-download and
re-flash. Your SD card is in a very bad state Your SIM has a pin card (effects some of the
early 2.2)
--I want to change my partition sizes
Doing this will require a TPT. These can be made or downloaded using the App TPT helper from
the Play Store ( as of now, there is NO TPT for Chinese Blades )
--I Want to send my Phone back to the Operator - how do I make it back to stock?
The best way to do this is to run a TPT which has been made for your operator's original
ROM. A TPT that is built to do this restores the phone to exactly as it comes out of the
factory. This includes BOOT, RECOVERY and SYSTEM partitions. The DATA and CACHE are also
wiped.
--I can not get into Recovery (clockworkmod)
Make sure you are pressing (and holding) the Volume Down button (-). If you Just see some
large text of FTM then you have not installed a Custom Recovery Image yet
--Phone cannot READ/Mount SD Card
1)SD Card is Damaged
2)Card is not formatted correctly. Download - MiniTool Partition Wizard
3)Card not Seated correctly in Holder
4)The Card needs cleaning : take it out and carefully clean it with alcohol (and a
cottonbud)
--Fastboot can not Install ClockworkMod
If you get waiting for device Check USB debugging is on.On windows check drivers. On others,
check your running as root and try other USB ports/ cables. Try using ADB Wireless from the
market. If you get "writing 'recovery': FAILED (status read failed (Protocol error))
android" change the usb cable, and try another USB port.
--I want to get rid of the inbuilt apps but don't feel comfortable installing a ROM
This is possible, you gain root on the device,then use tools to remove the apps. Eg: Root Uninstaller or Titanium Backup
--Have I got TFT or OLED?
Well if you have a UK device you may have OLED If you purcashed it in 2011 you almost
certainly have TFT Both are good- but having a TFT device means that you must avoid non-TFT
compatibe ROMS (All new ROMs are TFT friendly)On some ROMS you can use the Dialer to find
out. Dial *983*24474636# in the dialer. On the Stock Orange ROM Devices that have TFT
Screens have the build Number OUK_P729BV1.0.0B08 (OLED can have this buid also - but rarely)
Devices that have OLED Screens have the build Number OUK_P729BV1.0.0B0. The build Number can
be found in - Settings | About Phone | Build Number
--How can I keep my apps and settings when I install a new ROM?
Before installing a new ROM you can use Titanium Backup to backup all apps you have
installed. After the new ROM has been installed you can restore the apps plus their data (to
keep your Angry Birds progress and scores, for example). The paid-for version of Titanium
Backup allows you backup and then restore many/all apps with the batch command to save time
reinstalling each app individually.
In general, system settings should not be restored on a new ROM. Restoring them can undo the
effect of wiping data/restoring to factory settings before you flashed the new ROM and you
run the risk of incompatible settings causing forced closure of system apps or, even worse,
random reboots of the phone. Contacts can be restored automatically (and safely) by syncing
with your gmail account(settings->accounts & sync and turn on both sync options) - you need
to do this in your old ROM so the data is in place before you install the new ROM. Many
people have reported that SMSs can be restored safely between most ROMs with Titanium
Backup, but other system settings, e.g. wireless access points, may cause problems that may
require the ROM to be reflashed. In all cases you should always use Nandroid backup in
Clockwork to save the state and settings of your previous ROM which will easily allow you to
return to a working state of your previous ROM in case things go wrong.
--How do I remove a custom theme I installed on any ROM, without factory reset?
Simply Re-flash the original ROM over the top in Clockwork. You'll get the original theme
back.
--I want to install a ROM, but remove some of the
included APPs
Simply open the ZIP file you downloaded and browse to /system/app Then remove the APPS you
don't want - be careful, you don't want to remove apps like mms.apk (SMS) and Phone.apk
--Orange SIM card will not make calls, other networks SIM cards work
The phone, as delivered by Courier is barred from OrangeUK's own network until "activated"
If you buy your phone from an Orange shop they are activated (unbarred from the Orange
network) and handed to the purchaser.
--Phone won't boot - only vibrates when I press power
When you try to turn the phone on with the power button you just feeling a quick succession
of vibrations. This means there is not enough power in the battery to boot. Make sure your
phone is plugged into the Adapter and is using the supplied USB cable.
--Wifi Keeps dropping
On 2.1 and leaked 2.2 ROMS - wifi is a real problem. There are many different work-rounds;
however now the kernel source for 2.2 is released - new ROMs don't gave it. Alternatively
there's a Blade wifi fix app available
--Phone wont turn on. It just Buzzes and red light is on back button
Try charging with another cable - your phone is out of battery
--The phone is Not connecting to 3G/ Cant get Data/ Cant send MMS, etc.
If you cannot get data over 2g/3g then your APN setting may be wrong You edit the APN's in
Setting / Wireless & Network Settings / Mobile Network settings / GSM/UMTS Options / Access
Point Names / then click the phones MENU button (hard button) then choose Add APN.
Also check your SIM is 3G
--I am trying to unlock the phone, how do I get to the enter code screen
You can only see this screen by putting in a SIM that is not the same as the ROM you have
expects So if you have a Orange TFT device that is on the standard (stock) ROM, you will
need a SIM that is not Orange (Virgin/TMobile) Once you insert a SIM that is not unlocked
you get the ENTER code screen
--The Phone Wont Read Any SIM Cards
Thickening the SIM with layers of tape (on the non useful side) has proven to work
--Cant make outgoing calls when Wifi is ON
The icon on the the top bar shows 4 reception bars gets a small x on it, the red led flashes
and outgoing calls cannot be made. Switched to airplane mode and back returns the signal -
it only ever does it when wifi is on. This is probably because you are running one
of the leaked Chinese beta kernels. Running a ROM that has a new 2.2 source
Kernel will fix this.
--What is an MD5hecksum
MD5 is a way of checking that the file you have downloaded has not been corrupted in any
way. when you run the MD5sum command against a files the response is the files
"fingerprint". If this differs from the expected MD5, then you need to re-download the file.
MD5 can be checked directly on the device by using a file manager like astro - if you look
at the details of a file an MD5 is generated Windows
Get your md5sum utility from:
http://www.md5summer.org/md5sum.zip
Extract this Zip file contents and put them into the folder you want to run the command in.
--I want to change the files in the system partition
To do this you can use ADB to modify files or Root Explorer
--I Used Factory Reset now my Phone wont boot
Custom ROM resets are best done in clockwork. However you may have problems with
Unsigned Themes. If you have a theme Installed, you may need to re-install the Original ROM
over the top to get it to boot.
--I want to change how my phone's screen looks like / Theme my phone
In any ROM you can change your background(click the MENU hard button when in the home
screen). However some custom ROMs have themes
made for them. There is a whole section on themes and Apps for the ZTE Blade - However the
most themes are specifically matched to a single or a few ROM's. Some themes are simply
applied to launchers that support them - i.e. launcher pro.
Other need to be installed via Clockwork just like a normal ROM - for these you should
always boot the ROM before applying the theme. Also you should always do a clockwork
(nandroid) backup before applying a theme.
--I dont like the keyboard I have
Keyboards on Android can be swapped. To change a keyboard - Activate it in Settings >
Language and Keboard Then in ANY app do a long hold in any text areas wich wold normall show
the keybaord - then choose Input Method
--Bluetooth file Transfer doesn't work properly
Plain vanilla Android has seemingly limited general file transfer capabilities. You can
download market APPS that are far superior. Bluetooth File Transfer (free) Astro File
Manager (free) add the Astro Bluetooth module (free)
--I want to use A2SD but what do I do
Firstly you need a ROM that supports A2SD, next you need to know if it support EXT2/3/4. Now
you need to change the way your SDCard is Partitioned. In Ubuntu use GParted - in Windows
get the home version of partition wizard. Now Copy EVERYTHING off the SD Card. Make the
FIRST partition the FAT32 one (primary partition) - leave 512MB or more for the EXT2/3/4
(where apps will be installed) Now Make Another partition (must be the SECOND) as EXT2/3/4 -
also make this primary. Now mount the Card and copy all your data back to the FAT32 Part -
assuming it fits. When you install/next boot you ROM, the EXT2/3/4 partition will be mounted
as DATA / this is where your apps go from now on.
--I have bought a bigger SD Card and want to swap it into my Phone
If your just using FAT32 (no app2sd) this will be easy. Right Simple - mount the current one
over USB on your Computer (you can do this in Android - or in Clockwork) Copy everything off
onto your computer. Unmount and Swap new card into phone. Remount over USB. Copy everything
back on
--I am upgrading my ROM and don't want to lose my contacts
If you sync your contacts via Google (gmail account), then the contact will be re-
downloaded when you re-enter your Google Account after flashing. You can see your accounts
in Menu > Settings > Account & Sync Otherwise you can go into the Contacts App and choose
Menu > Import Export. The Export will made a new large file with all your contacts in. This
will be written to the root of your SD Card. Import will scan your SD Card and look for any
files that are contact backups.
--I set a BAD SSID in the Wifi Hotspot - now I cannot start Tethering
If you set a SSID on your hotspot to be too long (over 32 characters) or with non valid
characters - then you make it impossible to start the Hotspot. You MUST use ADB to edit the
hotspot name manually
: adb -d shell
: sqlite3 /data/data/com.android.provid
If sqlite3 is not installed on your ROM you can download titanium backup from the market
then use the alternate command
:adb -d shell
:/data/data/com.keramidas.TitaniumBack
--I want to import all my contacts into Gmail - so they can sync with my phone
Google dont tell you anywhere what the Magic format is of their CSV. Copy the first line
from below, then simply add all the contacts you need into the format of the
2nd line Most Spreadsheet programs will let you open the CSV and edit it. Then just import
the file into Google Contacts (selecting a group when you do it) - I suggest a new group.
--How do i get ICS on my phone
There is no official ics for the blade, however, There are several ics roms to choose from. However there is no perfect release and all of them have certain bugs and issues.
--Can I boot more than one rom on a ZTE Blade
Thanks to [email protected], Snap.IT and Jinxxed, this is now possible. Head over to the Blade Android Development subforum to see the threas
September 21st : ZTE BLADE DAY
Guys feel free to reply with corrections and suggestions so that I can add then to the OP
Thanks to yash_p90 and karthiknr for assistance
good job is helpfull
Nice.
Good job. You should probably do some formatting. I can help you with that if you want!
Please note that there is no method available to change the partition size on the Chinese Blades. Thus the TPT method won't work. You must mention this in your question "I have changed my partition sizes to have a 128MB system, I want to change it back"
/Sticked. I hope this and the Faq thread I stickied yesterday will offer easy accessible information and resources to the ZTE Blade users. I hope you guys appreciate QuantumFoam and karthiknr effort.
Quantum add the question "Is multiboot possible on Blade?"
The answer should be there in that old multiboot thread.. Wbaw answered I suppose..
Sent from my LT26i using xda premium
karthiknr said:
Quantum add the question "Is multiboot possible on Blade?"
The answer should be there in that old multiboot thread.. Wbaw answered I suppose..
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
K.....ill add it.
Added multiboot question on karthiknrs suggestion
I think you should add in how instal custom rom an how keep safe personal data the nandroid backup ( via the recovery), its better than titanium backup and very easy, otherwise its very good :thumbup:
Envoyé depuis mon Blade
Gokh said:
I think you should add in how instal custom rom an how keep safe personal data the nandroid backup ( via the recovery), its better than titanium backup and very easy, otherwise its very good :thumbup:
Envoyé depuis mon Blade
Click to expand...
Click to collapse
Thanks.
I'll add it
total internal memory issue
i got two dell xcd35 (zte blade) phones.... one of them is gen1 and other is gen 2... i installed rom manager and then installed cynogen mod 7 on the gen 2 device and i got 160MB total internal memory... for the second phone i firstly converted gen 1 to gen 2 and then installed cynogenmod 7 and i got 294 MB as total internal memory! please help me out to get 294MB as total internal memory on the other device too
I already replied to ur thread in the General Forum
very helpful,
thanks ∩__∩
I've a ZTE V889D bought from China. Is this Blade version? When I run Mr Pigfish, it says unknown model. It has similar spec:
http://www.zte.com.cn/cndata/mobile/mobileinfo/201203/t20120329_298335.html
No, that's not a blade. It uses MSM7227A as CPU, that is an ARMv7 (blade uses MSM7227 that is ARMv6). Blade in China is called V880 and that version has only 256mb RAM ( http://www.dealextreme.com/p/zte-v8...dma-3g-single-sim-w-wifi-white-101744?item=24 )
Your phone should be the ZTE Skate Acqua: http://pdadb.net/index.php?m=specs&id=3403&c=zte_skate_acqua or something very close to it (looks like that V889D has dual sim support, but official Skate Acqua shouldn't have it).
CTRL+ALT+DEL said:
No, that's not a blade. It uses MSM7227A as CPU, that is an ARMv7 (blade uses MSM7227 that is ARMv6). Blade in China is called V880 and that version has only 256mb RAM ( http://www.dealextreme.com/p/zte-v8...dma-3g-single-sim-w-wifi-white-101744?item=24 )
Your phone should be the ZTE Skate Acqua: http://pdadb.net/index.php?m=specs&id=3403&c=zte_skate_acqua or something very close to it (looks like that V889D has dual sim support, but official Skate Acqua shouldn't have it).
Click to expand...
Click to collapse
Is there forum ZTE Skate Acqua or a custom firmware?
Thanks Quantum !
Few things were total new. Like bluetooth file transfer capability, I thought it's only Blade that is having limited bluetooth profile.
Also can you add a question about swap. I know only poor (256MB RAM) fellows like myself are going to benefit. No issues for me for one plus week of usage without a reboot.
Sent from my Idea Blade
rahulsa said:
Thanks Quantum !
Few things were total new. Like bluetooth file transfer capability, I thought it's only Blade that is having limited bluetooth profile.
Also can you add a question about swap. I know only poor (256MB RAM) fellows like myself are going to benefit. No issues for me for one plus week of usage without a reboot.
Sent from my Idea Blade
Click to expand...
Click to collapse
Your welcome.
I'll add swap, though I can tell you that's only if you use your phone for HD gaming
Quantum! Looks like you'll have to edit the MultiBoot part in the first post.. Was going through modaco just now.. [email protected] just made it work.. Hell Yeah!!xD
Sent from my LT26i using xda premium
karthiknr said:
Quantum! Looks like you'll have to edit the MultiBoot part in the first post.. Was going through modaco just now.. [email protected] just made it work.. Hell Yeah!!xD
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Yeah I pmed you about it. That guy is a genius if he manages to pull it off