Herald won't turn on - Wing, P4350 General

Hello,
first of all: sorry for my bad English, I will try to make you understand it.
I have a problem with my Herald. I hardspled it and put a rom on it. It worked really well, but I wanted it to be in my own language so i downloaded another ROM. During the installation of that ROM (I did it with ROMUpdateUtility), the phone fell off the PC and the cable pulled out. The phone was stuck in bootmenu and later went out.
Now I can't get it on anymore. I can't charge it (well, maybe it's charging, but there are no lights at all), I can't turn it on, I can't connect it to the PC ( the PC doesn't reccognize it) and I can't get into Bootmenu.
I tried a soft reset and a hard reset, but nothing happens. Is there a solution or do I have to buy a new phone?
Thank you!

Related

Bricked Hermes (SPV M3100) while flashing SPL - any help or sugestion are wellcomed

All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...
The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...
Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd
I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.
get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it
Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???

i think i bricked my phone help

i was running the button program and it stopped at 98% and the bar turned red. i did the recovery process and got the colored screen. after that i couldnt active sync phone with computer, i turned the phone off and now cant get it to turn back on. i am f$#%ed arent i
any help would be wonderful.
thanks
Which is your device,G3 or G4 ? well,if its a G3,then try to get into bootloaders (multicolor screen),if it gets there,try to flash Button's Rom again,but if its a G4,then I'm afraid it might be 'Bricked',still try to get into bootloaders,if it gets there,then its safe.
Cheers!
Don't worry i bricked my G4 like 3 or 4 times already but managed to revive it lol
If yours is a G4,
-enter bootloader ( i think camera+soft reset button) -- if you can't get into bootloader, maybe it's time to pay a visit to service center
-flash using wizard love ROM, just use the RUU included in the rar file, if you're not italian, just "Avanti" means something like next (http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar)
-After installation is finished and your device is alive again, install EnableRapi.cab and Cert_SPCS.cab
-SOFT RESET
-Let it reboot until you get into the today screen (ignore the ugly splash, that's the price you have to pay to get your device alive.. )
-Re-flash WM6 using Shelltool, read the shelltool documentation and make sure you don't miss anything.
I read there are easier method like soft and hard SPL, but never try. The above is what I always do when I brick my wizard.
its a g3
but the thing is everytime i try to turn it on, nothing happens. The first time, after it stopped at 98% i turned it off and got the bootloaders screen, but active sync didnt work, then i turned it off again and it never came back on. the next day when i got home, try to turn on and nothing. Also when trying to charge phone, no orange light shows up. anything you can think of will be awesome
thanks
chris
dead battery perhaps? try borrowing one of your friend's charged battery.
I bricked my wizard several times but never got to that "really dead" point.
The only thing I can think of is just, IF you managed to get that bootscreen again, and can have your wizard alive long enough to flash, don't turn it off again, but try re-flashing using RUU (they worked on bootscreen even though active sync is not connected). I also don't have experience reviving G3s, maybe another member with G3 can help?

my Qtek 9000 just went dead and wont turn on!!

I upgraded my uni with ranju rom 2months ago and worked perfect.Yesterday after a call the uni froze when i restarted, the uni black out. have tried both hard and soft reset. Nothing happens in soft reset, but hard gives U " Press 0 to restore to factory default and X to exit". but if i press 0, the uni goes off again.,
Battery? Can you enter a bootloader and re-flash the ROM?
I can't get pass "Press 0 to restore to factory default -Press X to exit" screen
i also have same problem with you. and i have connect my device to PC usb cable, then PC detect my universal but cant recognize it as pocket pc.
please anyone help us.....
hello
hi all, and thanks in advance for reading this thread.
my cousin gave me his qtek 9000 saying that it was dead. being a dumbass, me decided to try and give it back life. as mentioned before, me a dumbass. After seaching the web for hours, i would normally be now saying, i give up. but no.
so , please. help.
the only thing i can tell u is that when i plug it in the pc, a red light starts bleeping. Won't turn on, soft and hard reset do not seem to make any effect, nor the power+light button.
again, please, help.
Had exactly the same...my qtek 9000 was just lying in the closet for a long time and would not boot anymore...
When I used it last time al was fine. I figured a dead battery so bought a new one...
It would give me the red LED while charging, would not be recognised on the computer etc.
Did a hard reset and then got it into the bootloader...
Had to run my laptop on XP as under Win7 it would fail to flash or do anything, but under XP it flashed properly.
After flash installed my back-up and all seems to be running fine now!
May be it helps anybody...

Bricked Phone

Dear people,
I am really searching all day how to unbrick my device, I tried everything, and still nothing worked so far. I got a phone from a friend who tried to update the software and probably removed the cable while flashing. Now when I turn on the phone the only thing I see is the boot logo and nothing happens after.
It is possible to go into the boot-modus (with the 4 colors). This way it worked for me to make a USB-connection with my PC. I tried a couple of roms but nothing worked so far, everytime when I try to flash the device, it will jump to the grey screen with the % bar and then I wait for it to go to the 100%, but when it goes to 1% the phone instantly reboots, this happens everytime I try to flash the device. After it reboots it shows the boot-screen (logo of the half-flashed rom)
I hope you got an answer for me to fix this phone. Like I said I was searching all day for an answer and tried several things but nothing worked so far, any suggestions? Please...
Hi,
Yes I tried the WM5 rom, but the same thing happened, after 1% the phone rebooted...
Hold on, trying another one right now that seems to work...
Okay I managed to fix the one using another official ROM
this one:
http://www.smartmobility.nl/_BIN/TRI_DT_NLD_1234042_103_6275_1380011_108_Ship.zip
Thnx at3m
You have to flash Hard SPL: http://trinityguides.info/index.php?option=com_content&task=view&id=39&Itemid=66
Happend to me once, and after flashing this, never again.
chalid said:
You have to flash Hard SPL: http://trinityguides.info/index.php?option=com_content&task=view&id=39&Itemid=66
Happend to me once, and after flashing this, never again.
Click to expand...
Click to collapse
Yeah after I put the official rom on again you need to hard-spl it. thnx ^^

[Q] Help!! AutoHardReset on T3232

Hi all, I have a t3232 clone, with this problem: After reboot it, or soft reset, or turn it on, it does as if as a hard reset it. I flash it with more than one ROM, in more than one SD card, in more than one computer, and always occur the same thing. Hard reset, every time I reboot it, soft reset it, or turn it on.
Anybody knew about this error???
Thanks for the help. Sorry for my english, I from Argentina.
Update: I flashing rom with sd card update mode and with usb update mode, many differents ROMs ( 6.1, 6.5, different languages, cooked and originals ). Every worked fine in any case, until I reeboot, turnoff-on, or soft-reset....... in this case, it boot as if as hard reset occur.......
disasembly the cell, and check for water into the flex cables and buttons, some times the buttons are in shock and occure that the phone make this kind of extrange facts.

Categories

Resources