Related
Guys, thanks to all of you - especially frysee, who was a big help via Gtalk - the biggest part of my problem is solved:
My Transformer is still bricked and display won't turn on, but I was able to go back to stock ROM and wipe all personal data. So I won't get any trouble with warranty
If anyone is interested, me or frysee could write a How To for returning to stock ROM and retrieve warranty when screen is dead.
Thanks again!
qwer23
_____________________________________
Hi Guys!
I have a problem that is pretty common over at MoDaCo, but I haven't read anything about it here.
My Transformer sometimes doesn't turn on or wake up from sleep mode when turned on already. You can push the power button endlessly and nothing happens. Then suddenly it'll turn on as if nothing had happened.
I had this problem the first time right out of the box, so there's no bad software installed by me, don't know what ASUS did though. Perhaps it's one of the pre-installed apps.
As I said, normally it eventually comes to life again, but now I couldn't turn it on for a whole day! After I had no success, I left it on the charger over night, but still nothing this morning.
I feel I tried everything, pushed Vol Down + Power to go into recovery, pushed Vol Up + Vol Down and plugged USB to go into (useless) flash mode just to see the device to something, but no.
The only things that happen, if I push power:
- if I plug USB, the Windows plug and play sound plays and if I force shutdown the Transformer again (long-press power), the unplug sound plays. The device even appears in the Explorer and I can access SD card, but it only shows empty folders, no files in them.
- When I force-shutdown the device, I hear an internal "click" sound, similar to the one when you switch from front to rear camera, and you hear the speakers turn off. So it seems to initialize everything and stuff...
But all the time the Transformer screen stays dead
Any advice? Really need your help here guys! At MoDaCo there's no answer so far...
Regards,
qwer23
I was initially having this problem with my Transformer (it would usually happen when it had gone on standby and it couldn't get it to turn back on again) until I ran the ASUS updates on it - have you been able to update your Transformer on the occasions it did turn on for you?
If you've rooted it and stopped the OTA updates going onto it, you might just have to undo that and get an official ASUS firmware build on there to help fix the problem.
demonotter said:
I was initially having this problem with my Transformer (it would usually happen when it had gone on standby and it couldn't get it to turn back on again) until I ran the ASUS updates on it - have you been able to update your Transformer on the occasions it did turn on for you?
If you've rooted it and stopped the OTA updates going onto it, you might just have to undo that and get an official ASUS firmware build on there to help fix the problem.
Click to expand...
Click to collapse
Hi!
First of all, thx for your answer.
Well as I said, the first time the problem occured, the device was out of the box and untouched before. So I don't think it has to do with something I did.
For me it normally also happened when device was in sleep mode, except the first time out of the box
I installed a custom ROM + Clockworkmod Recovery after that, hoping it'll fix the deep sleep problem. And it really didn't happen again - until now
I didn't turn off OTA updates as I first saw that thread when the device was already dead Perhaps it tried to OTA update itself but I guess I would have to confirm this manually right? And I didn't do that...
Reflashing another ROM or the stock ROM was my first idea, too. But hell, I can't even go to recovery! No matter what I do, press, plug or unplugg, the screen stays black!
Nice, another german Transformer
"playing the plug and play sound" means you propably have adb access? Tried getting a logcat?
frysee said:
Nice, another german Transformer
"playing the plug and play sound" means you propably have adb access? Tried getting a logcat?
Click to expand...
Click to collapse
yes, being unable to wait for the german release, i imported from uk
adb gives me "device not found". even though i'm not a total noob, i don't know what i have to change to make it work. any advice? sadly i'm working while my tf is charging @home so can't really try something. i only hope you guys have some ideas
Sent from my rooted X10i using awesome custom roms
qwer23 said:
Reflashing another ROM or the stock ROM was my first idea, too. But hell, I can't even go to recovery! No matter what I do, press, plug or unplugg, the screen stays black!
Click to expand...
Click to collapse
Ahh. I didn't realise the screen was completely dead, I thought you had it working some of the time as had happened to me.
If you're seeing it in Explorer, maybe it is just a hardware failure and you'll have to get Asus to look at it...
demonotter said:
Ahh. I didn't realise the screen was completely dead, I thought you had it working some of the time as had happened to me.
If you're seeing it in Explorer, maybe it is just a hardware failure and you'll have to get Asus to look at it...
Click to expand...
Click to collapse
no i guess that it is indeed the same thing that happened to you, sometimes it worked, sometimes not. only this time it doesn't come back from the not working part I guess you see yours in explorer too if it troubles to get out of deep sleep. i guess it's just the screen that sometimes doesn't turn on for all with that problem. but for me it doesn't even turn on for booting
Sent from my rooted X10i using awesome custom roms
It's possible. I don't think I tested connecting it to the Explorer while the screen was off, I assumed it just wasn't on.
Can you test it with the HDMI out and see if that shows you what would be on screen?
demonotter said:
It's possible. I don't think I tested connecting it to the Explorer while the screen was off, I assumed it just wasn't on.
Can you test it with the HDMI out and see if that shows you what would be on screen?
Click to expand...
Click to collapse
Yeah, good idea! Will try this asap when I'm back home. Do I have to press something on the TF to enable HDMI output or is it enough to plug it in?
qwer23 said:
Yeah, good idea! Will try this asap when I'm back home. Do I have to press something on the TF to enable HDMI output or is it enough to plug it in?
Click to expand...
Click to collapse
You just plug it in.
qwer23 said:
Hi Guys!
I have a problem that is pretty common over at MoDaCo, but I haven't read anything about it here.
My Transformer sometimes doesn't turn on or wake up from sleep mode when turned on already. You can push the power button endlessly and nothing happens. Then suddenly it'll turn on as if nothing had happened.
I had this problem the first time right out of the box, so there's no bad software installed by me, don't know what ASUS did though. Perhaps it's one of the pre-installed apps.
As I said, normally it eventually comes to life again, but now I couldn't turn it on for a whole day! After I had no success, I left it on the charger over night, but still nothing this morning.
I feel I tried everything, pushed Vol Down + Power to go into recovery, pushed Vol Up + Vol Down and plugged USB to go into (useless) flash mode just to see the device to something, but no.
The only things that happen, if I push power:
- if I plug USB, the Windows plug and play sound plays and if I force shutdown the Transformer again (long-press power), the unplug sound plays. The device even appears in the Explorer and I can access SD card, but it only shows empty folders, no files in them.
- When I force-shutdown the device, I hear an internal "click" sound, similar to the one when you switch from front to rear camera, and you hear the speakers turn off. So it seems to initialize everything and stuff...
But all the time the Transformer screen stays dead
Any advice? Really need your help here guys! At MoDaCo there's no answer so far...
Regards,
qwer23
Click to expand...
Click to collapse
When it seems dead, try holding the power button for about 5 seconds (or whatever time you hold it for when turning it off)
Leave for about 2 minutes then hold power button again (like you do when turning device on) and it should boot.
checkbox111 said:
When it seems dead, try holding the power button for about 5 seconds (or whatever time you hold it for when turning it off)
Leave for about 2 minutes then hold power button again (like you do when turning device on) and it should boot.
Click to expand...
Click to collapse
Tried that a lot of times already. No help.
Phone still won't turn on, but I just realized I cannot only access my SD Card, I can also access internal storage.
Is this of any help?
qwer23 said:
Tried that a lot of times already. No help.
Click to expand...
Click to collapse
Then your ****ed!
checkbox111 said:
Then your ****ed!
Click to expand...
Click to collapse
I guess so
I'm getting a mini-hdmi cable today to determine if the screen is broken, because i have the feeling that ***** is booting but not showing anything...But I'll have to send it to ASUS nonetheless. Has anyone ever sent a device in for warranty reasons with custom software (CWM, Custom ROM) on it? What kind of trouble will I have to face?
I'd say try it with the HDMI cable, see if you get anything up on it and if the touchscreen/everything else still works, see if you can get the latest official ROM on there, see if that fixes the problem.
If nothing else, you can then send it back with an official firmware on it.
Try holding the power button for 5-10 sec, then press power + volume down (might be volume up - try both) together for another 5-6 sec. You'll get to a reset screen where it asks you to confirm if you want to wipe everything. press volume down (I think!! - read the screen carefully) instead to boot normally.
hope this helps
Its 10+ seconds for a full power off by the way, nothing shorter than that. If you changed any system files either by flashing or by pushing via ADB then you will have invalidated your warranty. Unless you can restore it to the way it was before you fiddled with it, you'll have an expensive paperweight.
sbirsen said:
Try holding the power button for 5-10 sec, then press power + volume down (might be volume up - try both) together for another 5-6 sec. You'll get to a reset screen where it asks you to confirm if you want to wipe everything. press volume down (I think!! - read the screen carefully) instead to boot normally.
hope this helps
Click to expand...
Click to collapse
Not possible since I installed CMW.
stuntdouble said:
Its 10+ seconds for a full power off by the way, nothing shorter than that. If you changed any system files either by flashing or by pushing via ADB then you will have invalidated your warranty. Unless you can restore it to the way it was before you fiddled with it, you'll have an expensive paperweight.
Click to expand...
Click to collapse
Big bummer And sadly there are no "ASUS Stores" around where I could use a stupid employee who has no clue and is convinced it's hardware related.
Well I don't have my HDMI cable by now and will try this first, but if that doesn't work:
Can someone give me a step-by-step how I can access the restore function of CWM without seeing anything on my device? I did a backup in CWM before installing the custom ROM. Perhaps tell me sth. like this: "press power+vol. down on start, then after approx. x seconds press vol up, wait a bit to make sure CWM started, press vol down twice, to go to recovery, ..."
And can someone do the same for the stock recovery to reset the device? Perhaps there's a chance that a failed OTA update deleted CWM an there's the stock recovery.
I know the chance to save it like this are small, but otherwise a lot of money is lost
Regards,
qwer23
On the flip side however, you could probably make some money by being the first to dismantle your device, and sell the photos of the internals to some website like iFixit. Then you could also sell it off as parts on eBay. Obviously it might take more effort than you are willing to give it, but at least it's another option.
If you do decide to open it up I would love to hear what mA rating the battery has on its label. Not being able to find out the actual proper rating from any site has been driving me nuts. I believe it's 6800mA but im not 100% sure.
Just bought my Advent Vega today and was all running fine. Charged it too 100% then turned off and booted into the stock recovery. I then waited for it to show up on the computer as i have already got the drivers installed as i have jjust today flashed someone elses vega on the computer. mine didnt show up and then unplugged it and now it wont turn on at all. Tried charging it and then try booting. Unplug charger nothing. The thing is that the charging light still shows.
Any Help would be great. Dont want to have to send it back for repair. it may take weeks.
Thanks
Alex
Hmmm.... it could be a faulty unit, but my guess would be that you need to try at least 10x to try to turn it on.
I know some people complained that the buttons are very poorly designed and sometimes don't even work.
It's the same for my tablet, the "power/home" button doesn't always work like it should.
Once, I had to retry five times in order to power on the device.
If it's not that it could be some other minor issue, try holding the power button for a long time (8 sec), or try to go into recovery again, or something like that.
a sighn its trying to boot is the blue led under the camera tilt the vega away from you and look at the edge of the LCD it will glow when powering on
have you tried push back button, hold it, then press power button 2 second, the release the power button while still pressing the back button? it should be recognized and can be flashed
pramanta said:
have you tried push back button, hold it, then press power button 2 second, the release the power button while still pressing the back button? it should be recognized and can be flashed
Click to expand...
Click to collapse
Some times this can take several attempts.. and i mean several!
I actually had Audi running and had it connected to the pc so could tell if it had worked or not... not the correct way i know but it worked for me.
Interested to know if you ever got this sorted alcurtis93? I'm having the same issue with a vega where it won't even bring up the backlight. No life in it whatsoever.
A bit of a late reply, but try to wipe your device and maybe even flash a newer custom rom
My samsung Focus is about 1.5 years old.. I plan to switch carriers at the end my of contract since AT&T is giving me lots of dropped call at the new place we moved to.. The phone is obviously out of warranty, so I am looking to see if I can fix it myself.
The power button on my Samsung focus is behaving very funny lately. When I hit the power button with the phone awake, it thinks I did a "long press" of the power button and shows me the shutdown pull-down image! If I pull-up the image, the phone still reboots...
If I press the power button when the phone screen is OFF, instead of turning on the phone, it again shows the pull-down image, and the same behavior ensues - regardless of what direction I pull the image in, it shuts down the phone.
Some things I have already tried:
I have tried a hard-reset (camera+volume+power, and format the device), but the behavior continues.
I have removed my SD Card (I am using the AT&T approved one), performed hard reset, and problem continues
I have tried a different battery (from my wife's focus), and problem continues
At this point, I am guessing that most likely, the power button connector is loose.. but I am not 100% sure.. Any suggestions on things to try?
Seems like the spring in the power button is gone. I suggest when you want to press it, lean the phone to the right (with the power button towards the ground) so when you press it, gravity helps popping it back.
Or replace the power button.
EnderPsp said:
Seems like the spring in the power button is gone. I suggest when you want to press it, lean the phone to the right (with the power button towards the ground) so when you press it, gravity helps popping it back.
Or replace the power button.
Click to expand...
Click to collapse
Tried the first trick... didn't seem to help..
Any tips on where I can find a replacement power button and how I can replace it?
See my response here (and the thread referenced in my second reply). Seems to be one of the issues that appear in time... And in another case it was the battery...
EnderPsp said:
See my response here (and the thread referenced in my second reply). Seems to be one of the issues that appear in time... And in another case it was the battery...
Click to expand...
Click to collapse
Thanks EnderPsp!
I have ordered a new battery for now to see if it helps.. its a non-OEM battery off eBay.. Don't want to spend too much without knowing if that is indeed the problem..
I can't find a power button replacement part anywhere... I went over the video and the instructions to reach the power button housing does not seem very bad.. definitely do-able if I can find a replacement part..
walletless said:
Thanks EnderPsp!
I have ordered a new battery for now to see if it helps.. its a non-OEM battery off eBay.. Don't want to spend too much without knowing if that is indeed the problem..
I can't find a power button replacement part anywhere... I went over the video and the instructions to reach the power button housing does not seem very bad.. definitely do-able if I can find a replacement part..
Click to expand...
Click to collapse
The button itself is plastic (you can find some on ebay), and I don't know how it works, actually (If it's a spring or otherwise).
I suggest you watch a take apart guide and maybe, just maybe it's just dirt, which you can clean.
You'll know more and afterwards please share the result with us.
EnderPsp said:
The button itself is plastic (you can find some on ebay), and I don't know how it works, actually (If it's a spring or otherwise).
I suggest you watch a take apart guide and maybe, just maybe it's just dirt, which you can clean.
You'll know more and afterwards please share the result with us.
Click to expand...
Click to collapse
And now its completely gone... the power button won't respond at all.. the phone has been shut all day. If I take the battery out and put it back in, the SAMSUNG logo shows up for a few seconds and then the phone turns off again.. No way to turn it back ON using the power key..
I sat down to open the circuit yesterday only to realize that I don't have a #000 screwdriver... the smallest one I have is #00 which is too big for the 7 screws that hold the back panel
Off to Grainger today to see if I can find a 000 driver.. It can't get any worse now, so might as well open the phone!
Sure thing - I will update the post later with what I find...
walletless said:
And now its completely gone... the power button won't respond at all.. the phone has been shut all day. If I take the battery out and put it back in, the SAMSUNG logo shows up for a few seconds and then the phone turns off again.. No way to turn it back ON using the power key..
I sat down to open the circuit yesterday only to realize that I don't have a #000 screwdriver... the smallest one I have is #00 which is too big for the 7 screws that hold the back panel
Off to Grainger today to see if I can find a 000 driver.. It can't get any worse now, so might as well open the phone!
Sure thing - I will update the post later with what I find...
Click to expand...
Click to collapse
You didn't say if the same happens with the wall charger connected.
Now, If you're going out, try and drop near a phone shop. Ask them if they can help you test with one of their batteries, either for a Focus i917 or from a Galaxy S i9000
Good luck mate.
Dang i thought i was the only one with this issue...
Mine started acting up about 3 weeks ago and it was seriously annoying especially when driving. I would press the lock button to change songs, but it thinks i did a long-press and does the "slide down to power off" thing. Even if i swipe up, the phone would switch off.
Then today, i take my phone out my pocket to send a text and find it's powered off. Won't even switch on now
Ender:
Plugging the phone in does NOTHING. The screen remains black.
Reinserting the battery causes the SAMSUNG logo to appear on-screen but again, goes black after 4-5 seconds.
Holding down the power/lock button has no effect, it's unresponsive.
I'm so pissed off this is happening 6 months before my contract is up. -_-
Don't know what else to say... I hope you still have warranty?
EnderPsp said:
Don't know what else to say... I hope you still have warranty?
Click to expand...
Click to collapse
Not extended no... :/
I've managed to get it into "download mode" now though, and my laptop recognises it as "SAMSUNG CDMA Technologies"... Huh?
---------- Post added at 05:02 PM ---------- Previous post was at 04:45 PM ----------
If i have it plugged into my laptop,
hold vol down, power, and camera while inserting the battery i get to the hard reset screen. But then that disappears in the same 4-5 second window.
Ok, it's working again... I left the battery out for a few hours (literaly about 3), then pressed hard on the power button, and placed it (the battery) back in the phone.
Let it turn on and then back off by itself, then pressed hard on the power button.
pressed the button normally, and it booted up no issues. So far works fine.
I expect this issue is partly the power button, and something else unknown
EnderPsp said:
You didn't say if the same happens with the wall charger connected.
Now, If you're going out, try and drop near a phone shop. Ask them if they can help you test with one of their batteries, either for a Focus i917 or from a Galaxy S i9000
Good luck mate.
Click to expand...
Click to collapse
Yes' same thing with wall power. New battery arrived and did not help. Went to a local cellphone repair and the guy said main board needs replacement.. he suggested to buy another phone since repair will be more expensive.. he said that he needs to remove soldering on the board reinforce an auxillary power button battery and resolder it in.. no guarantees and will cost atleast $150
Jfran71 said:
Ok, it's working again... I left the battery out for a few hours (literaly about 3), then pressed hard on the power button, and placed it (the battery) back in the phone.
Let it turn on and then back off by itself, then pressed hard on the power button.
pressed the button normally, and it booted up no issues. So far works fine.
I expect this issue is partly the power button, and something else unknown
Click to expand...
Click to collapse
Lucky you!! This seems like a common problem with several Samsung phones based on a quick google search
Also bummed that this happened with 6 months remaining ...Now I am somewhat stuck since I want to switch from AT&T due to call issues with several months remaining.. and dont want to buy one till wp8 is out...
Just for fun... I am going to find a 000 screwdriver and try to re-jig the power button.. nothing to loose with the phone refusing to start anyway!
For what it's worth, my power button had been getting increasingly creaky over the course of the last few months, and although not sticking, was requiring ever more pressure to operate. Also, the sound of rusty bedsprings every time I went to use my phone was getting somewhat embarrassing.
I found the sturdiest piece of paper that I could wedge in between the button and the rest of the phone, put a bit of PB Blaster on the paper, and wedged the paper in. The button has since been as good as the day I took the phone out of the box for a couple of months now.
*Edit: Should probably mention that the paper isn't supposed to stay in there - it was just used to apply the lube without soaking the phone.
Jfran71 said:
Ok, it's working again... I left the battery out for a few hours (literaly about 3), then pressed hard on the power button, and placed it (the battery) back in the phone.
Let it turn on and then back off by itself, then pressed hard on the power button.
pressed the button normally, and it booted up no issues. So far works fine.
I expect this issue is partly the power button, and something else unknown
Click to expand...
Click to collapse
So its working completely fine now? No issues? I'll try that but im not hopeful.
I've been having the same issue, started yesterday. There appears to be no issues with the actual button itself, it doesnt appear to get stuck or anything to cause this, even without the external shell and just compressing the sensor itself.
walletless, you said that you tried reformatting it and everything? Damn. I was expecting it to be a software issue. I'll mess with the button mechanism a bit and see if theres anything weird with it
Phone is dead
re-jigging and cleaning around power button did not help.. I ended up ordering a chinese knock-off of HTC Note instead
Does any have this problem, but on a normal stock rom?
I was thinking it might be just custom roms, I don't think that would have anything to do with it
Its worth a shot though
titanhydro said:
Does any have this problem, but on a normal stock rom?
I was thinking it might be just custom roms, I don't think that would have anything to do with it
Its worth a shot though
Click to expand...
Click to collapse
My phone died last month. I only installed updates that came through Zune up to 7.5. I went into AT&T and they told me too bad because it was out of warranty. I called Samsung, and they wanted me to 'volume down, camera, power' reset my phone, which didn't work. Samsung told me to send it to them for $70 because I was out of warranty.
Instead I entered a developer competition for a Lumia 800 and won. Now I just have a dead focus, and a new 800. I'd still be interested if anyone finds out a way to fix the focus problem.
Hey Guys I need some help please!
I have a friend, which will be joining this thread soon, that has a samsung tab 2 GT-P3113 7" .
He is not able to power on the device, I suggested holding the power button down for 30-40 seconds but that didn't work.
He charged it overnight and he can see the charging icon, he then tried again holding the power button for 30-40 seconds...still nothing.
He informed me that when he connects his tab to his computer it says:" I should install OMAP3440 driver for connection".
Sorry , this is all I have, I'm not familiar with the tab 2 .
Thank you!
Isnt there a reset button/procedure? Like hold power button and volume up or down?
My P3110 will not arrive till next week so i can say for sure.
Try holding the Volume Down button and the power button. Keep holding them and you should get a warning about running custom software. If you get this, then you could download an Odin restore package and flash it to the tablet to get it back up and running. The fact that it shows the charging image is a good sign, Hopefully it can be fixed from there.
maztahbr said:
Isnt there a reset button/procedure? Like hold power button and volume up or down?
My P3110 will not arrive till next week so i can say for sure.
Click to expand...
Click to collapse
Yes, I did, but it doesn't work for this tab. Only there is a good sign I can see: the charging icon come up when I plug tab to wall or pc, and when I try to connect to pc, I get a message from pc saying I should install driver for OMAP3440. This is the driver for Texas Instrument processor that come inside tab.
I don't know if this tab is bricked or not, so I'm stop just at this step.
Thanks & thank you so much to spagman72 for his valuable help
---------- Post added at 01:19 PM ---------- Previous post was at 01:14 PM ----------
imnuts said:
Try holding the Volume Down button and the power button. Keep holding them and you should get a warning about running custom software. If you get this, then you could download an Odin restore package and flash it to the tablet to get it back up and running. The fact that it shows the charging image is a good sign, Hopefully it can be fixed from there.
Click to expand...
Click to collapse
Yes, I did exactly as you have said, but it doesn't work, nothing warning about custom software, just black screen. Also, pls note that when I try to connect to pc, I get a message from pc saying I should install driver for OMAP3440. This is the driver for Texas Instrument processor that come inside tab.
Thank you
It is for omap4430 driver (not omap 3440)
Correction: when i have connected tab to pc, message is for install drivers OMAP4430, not OMAP3440 as I have said before. Very sorry for this mistake. :crying: :crying:
Anyone to help pls..!!
When you see the charging icon unplug it from the charger then try and power and vol down. Don't keep holding power for to long or it will hard reboot it before it gets to download mode.
RomsWell said:
When you see the charging icon unplug it from the charger then try and power and vol down. Don't keep holding power for to long or it will hard reboot it before it gets to download mode.
Click to expand...
Click to collapse
Thank you RomsWell but when I unplug the charger and then press power and vol down keys nothing changes, just black screen. I think this tab is totally dead and another friend told me that I'll need a JTAG service. Anyone know about this, or where can I get it?
Thanks again
RomsWell said:
When you see the charging icon unplug it from the charger then try and power and vol down. Don't keep holding power for to long or it will hard reboot it before it gets to download mode.
Click to expand...
Click to collapse
Love your rom btw try volume down, (for download), or volume up, (for recovery), First then hold/engage power button and hold, then release power button after boot screen blacks out and continue to hold up or down volume for recovery/download. Appropriate screen should pop up...if you get that far there are many options and I'm sure someone here can help you
acefsw said:
Love your rom btw try volume down, (for download), or volume up, (for recovery), First then hold/engage power button and hold, then release power button after boot screen blacks out and continue to hold up or down volume for recovery/download. Appropriate screen should pop up...if you get that far there are many options and I'm sure someone here can help you
Click to expand...
Click to collapse
Thank you so much acefsw, but nothing has functioned for me yet, and also nothing to do for now..!! :crying: :crying:
alca00 said:
Thank you so much acefsw, but nothing has functioned for me yet, and also nothing to do for now..!! :crying: :crying:
Click to expand...
Click to collapse
Sorry to hear that. There are JTAG services where you can mail it in and they fix it, here's one http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-tab-2-7-0-brick-repair/ I am sure there are others out there. Good luck
acefsw said:
Sorry to hear that. There are JTAG services where you can mail it in and they fix it, here's one "" I am sure there are others out there. Good luck
Click to expand...
Click to collapse
Ok, I'll check it out and will let you know later, because at this moment I'm out of country.
Thanks a lot..!
My tab does this periodically...I usually just let it sit then hold down the power button and it boots. All stock, unrooted.
Sent from my Galaxy Nexus using Tapatalk 2
I'm happy again..!!
acefsw said:
Sorry to hear that. There are JTAG services where you can mail it in and they fix it, here's one http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-tab-2-7-0-brick-repair/ I am sure there are others out there. Good luck
Click to expand...
Click to collapse
Hey guys..!!
I'm happy again..! Yesterday, I received the tab from mobiletechvideos, and it is in great working order. These guys really are doing a awesome job..!
Thanks again to:
spagman72 (especially), acefsw (especially), maztahbr, imnuts, and RomsWell for his/her valuable help.
But above all to XDA developers
Happy new year for all..!
Guys, i have same probem but with Samsung Galaxy Tab 2 GT-P3110.
spagman72 said:
Hey Guys I need some help please!
I have a friend, which will be joining this thread soon, that has a samsung tab 2 GT-P3113 7" .
He is not able to power on the device, I suggested holding the power button down for 30-40 seconds but that didn't work.
He charged it overnight and he can see the charging icon, he then tried again holding the power button for 30-40 seconds...still nothing.
He informed me that when he connects his tab to his computer it says:" I should install OMAP3440 driver for connection".
Sorry , this is all I have, I'm not familiar with the tab 2 .
Thank you!
Click to expand...
Click to collapse
Hi guys, i got same problem with my Samsung Galaxy Tab 2 GT-P3110, but my when charging is showing charging icon for 3 sec, then switch off over and over again, when i unplug from charger, display switch on and show again for 3sec logo Samsung Galaxy Tab 2 7.0 then switch off over and over again. I try all keys combination but just one working. When is unplug from charger i press Volume - and Power then on display come Screen with Warning!! (Download Mode) but like before go off after 3sec again.
I think that will be battery dead or faulty, what you think guys about it.??
Maybe the battery its damaged
Enviado desde mi Atrix HD mediante Tapatalk
toma83 said:
Hi guys, i got same problem with my Samsung Galaxy Tab 2 GT-P3110, but my when charging is showing charging icon for 3 sec, then switch off over and over again, when i unplug from charger, display switch on and show again for 3sec logo Samsung Galaxy Tab 2 7.0 then switch off over and over again. I try all keys combination but just one working. When is unplug from charger i press Volume - and Power then on display come Screen with Warning!! (Download Mode) but like before go off after 3sec again.
I think that will be battery dead or faulty, what you think guys about it.??
Click to expand...
Click to collapse
If you can get into download mode it may be a good idea to try flashing firmware through Odin to rebuild it back to factory.
I had the same issue after flashing the wrong kernel/ Rom combo while trying to get ubuntu touch to boot.
Sent from my LGMS500 using XDA Premium 4 mobile app
tokenpoke said:
If you can get into download mode it may be a good idea to try flashing firmware through Odin to rebuild it back to factory.
I had the same issue after flashing the wrong kernel/ Rom combo while trying to get ubuntu touch to boot.
Sent from my LGMS500 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I know but download mode i show just for 3 sec so i cant do anthing, same if i connect to PC, 3 sec and thats all loop again
toma83 said:
I know but download mode i show just for 3 sec so i cant do anthing, same if i connect to PC, 3 sec and thats all loop again
Click to expand...
Click to collapse
Ah, mine stayed on if I immediately plugged it in... could well be the battery
Sent from my LGMS500 using XDA Premium 4 mobile app
tokenpoke said:
Ah, mine stayed on if I immediately plugged it in... could well be the battery
Sent from my LGMS500 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
The battery have power i just tested by multimeter, i dont know how to repair this, maybe jtag service can help.?? Anyone can confirm.?
Loose ribbon cable
spagman72 said:
Hey Guys I need some help please!
I have a friend, which will be joining this thread soon, that has a samsung tab 2 GT-P3113 7" .
He is not able to power on the device, I suggested holding the phttp://forum.xda-developers.com/images/smilies/cyclops.gifower button down for 30-40 seconds but that didn't work.
He charged it overnight and he can see the charging icon, he then tried again holding the power button for 30-40 seconds...still nothing.
He informed me that when he connects his tab to his computer it says:" I should install OMAP3440 driver for connection".
Sorry , this is all I have, I'm not familiar with the tab 2 .
Thank you!
Click to expand...
Click to collapse
I had this same problem with one of my Samsung tab 2 GT-P3113 7.0's. After trying everything I could find online I decided to open it up and have a look inside. Opening a 7.0 is different than a 10.1 so check a YouTube video to see how it is done. After removing the back cover I immediately noticed that a small ribbon cable had some how become disconnected. I simply snapped it back into place then checked all of the other ribbon cables I could see and then tried to turn the unit on and it worked! problem solved!
If you have tried all of the other methods posted then you should give this a try, because at that point you have nothing to lose.
My Tablet gets handled by a lot of people daily and most likely it was dropped which caused the cable to be knocked free of its connection.
it was working and suddenly it just died ive tried charging it and ive tried pressing power and power + volumen up and down and nothing seems to work. Any thoughts, ideas? the back cover is stuck in a notification it doesnt work also it seems to charge on the Wireless charger
luisumf said:
it was working and suddenly it just died ive tried charging it and ive tried pressing power and power + volumen up and down and nothing seems to work. Any thoughts, ideas? the back cover is stuck in a notification it doesnt work also it seems to charge on the Wireless charger
Click to expand...
Click to collapse
Try to get into download mode. Or wait a while
Sent from my YD201 using Tapatalk
luisumf said:
it was working and suddenly it just died ive tried charging it and ive tried pressing power and power + volumen up and down and nothing seems to work. Any thoughts, ideas? the back cover is stuck in a notification it doesnt work also it seems to charge on the Wireless charger
Click to expand...
Click to collapse
Try pressing power for about 15 seconds, it should reset then.
SteadyQuad said:
Try pressing power for about 15 seconds, it should reset then.
Click to expand...
Click to collapse
it doesnt reset the power button is useless, i guess ill have to wait for the battery to drain maybe then it restarts
adamo86 said:
Try to get into download mode. Or wait a while
Sent from my YD201 using Tapatalk
Click to expand...
Click to collapse
how do i get it in download mode?
luisumf said:
how do i get it in download mode?
Click to expand...
Click to collapse
The easiest way is plugging the usb cable (which is connected to your computer) to your phone while holding volume down button. No need to press power button. From download mode you can boot to recovery etc with the help of your pc.
Jeopardy said:
The easiest way is plugging the usb cable (which is connected to your computer) to your phone while holding volume down button. No need to press power button. From download mode you can boot to recovery etc with the help of your pc.
Click to expand...
Click to collapse
did not work
This sounds more and more like a case for Yota's repair center. If there wasn't something broken in the device one of these methods described in this thread should have worked.
Sounds like hardware to me.
I had the same issue. Left it on the table with the e-ink screen on top, came back hours later, the clock was 90 minutes behind and the phone dead. Resetting with 10 Seconds ON/OFF button didn´t work. Had to send it in. 2 weeks later got it back. They said they had to change the whole motherboard, even got a new IMEI with it. Then a few days later I tried the main camera and it did not work, error message by Android, unaccessible camera... Then by pressure on the camera it worked sometimes, sometimes only misty lines, sometimes splitscreen mode, sometimes not. Maybe a mistake by the service while reassembling the phone? Anyway, had to send it in AGAIN, got it back, sold it on ebay with 130 Euros loss and bought a new white one because I love the principle and options of the second screen so much. The white one is a newer batch, they say with some new (and probably more reliable?) hardware, so up until now I am completely satisfied, no error for 6 weeks (fingers crossed...)
My old black one was maybe a monday batch
petra333 said:
I had the same issue. Left it on the table with the e-ink screen on top, came back hours later, the clock was 90 minutes behind and the phone dead. Resetting with 10 Seconds ON/OFF button didn´t work. Had to send it in. 2 weeks later got it back. They said they had to change the whole motherboard, even got a new IMEI with it. Then a few days later I tried the main camera and it did not work, error message by Android, unaccessible camera... Then by pressure on the camera it worked sometimes, sometimes only misty lines, sometimes splitscreen mode, sometimes not. Maybe a mistake by the service while reassembling the phone? Anyway, had to send it in AGAIN, got it back, sold it on ebay with 130 Euros loss and bought a new white one because I love the principle and options of the second screen so much. The white one is a newer batch, they say with some new (and probably more reliable?) hardware, so up until now I am completely satisfied, no error for 6 weeks (fingers crossed...)
My old black one was maybe a monday batch
Click to expand...
Click to collapse
Hi Petra. Since you're using a Yotaphone as well, could I ask you to do a small favour for me please? After I had my YP rooted I accidentally deleted the system app "back screen manager". My back screen has stopped working since then. It'd be fantastic if you could just extract the system app from your phone and send it to me so that I can manually place the system app on my phone root folder. You don't have to root your phone for this. All you need is an App extractor from play store. And it will take less than 5 mins to extract and send it to me(Assuming that you are well versed with android OS). Here's my email address [email protected] or you could send me a link to the shared file. Do let me know if you are willing or not. Thanks a ton.