Related
So, I have installed HSPL 2.08. I flashed ChuckyDroid and it worked fine but I wanted more. So I flashed an Omega rom and it was cool but now I want to Flash Magldr1.3 and try wm7 or a nand android. The problem I am having is, when I start to flash the new rom, I get the HTC screen and 0% and it stays there forever. I end up pulling the battery and resetting the phone. I first tried with Mgldr then a few other wm6.5 roms with the same problem. Why can't I flash roms anymore?
I searched the thread and had no luck. I apologize in advance ir this has been covered before.
Try to flash stock Rom from tricolor or even from Your microSD card. And then hspl, magldr etc.
AzOutlaw said:
So, I have installed HSPL 2.08. I flashed ChuckyDroid and it worked fine but I wanted more. So I flashed an Omega rom and it was cool but now I want to Flash Magldr1.3 and try wm7 or a nand android. The problem I am having is, when I start to flash the new rom, I get the HTC screen and 0% and it stays there forever. I end up pulling the battery and resetting the phone. I first tried with Mgldr then a few other wm6.5 roms with the same problem. Why can't I flash roms anymore?
I searched the thread and had no luck. I apologize in advance ir this has been covered before.
Click to expand...
Click to collapse
How about this way.
Assuming you still can reach Boot Loader and You still have SPL 2.08 HSPL installed.
Go into bootloader screen and connect your phone using usb, and let the word: "serial" in the below of phone (the white color bar) changed to: "USB". If you fails, retry it using different ports, and dont forget to turn off your antivirus, firewall and internet connection, or even your screen saver.
While in bootloader, do "task 29", flash radio 2.15.xxx, install magldr 1.13 (all in sequence).
Assuming you succeed it. Now, we go into flashing NAND WP7 (or NAND Android).
Assuming that you already have NAND WP7 (or NAND ANDROID).
Go into magldr screen, you know how to do it right?
There, select option 5 (USB Flasher) and confirm it by pressing the phone call (green) button and connect your phone using usb to pc.
Run your NAND WP7 (or NAND ANDROID) rom.
Finish.
Good luck
I tried the oldest DFT WP7 rom (7004),but I could not boot into WP7.Stuck at DFT logo,I tried to put my microsd card and my sim card out of my phone but it did not work for me.
In addition to other rom such as Pdaimatejam_Rom(7740),HD2O (7720), Back to the future,It could not boot too.Same problem,Stuck at DFT or HTC logo before boot into WP7
I tried to task29 and installed magldr and flashed WP7 rom again in serveral times but it stuck at logo again and again.
My micro sd card is SanDisk 8gb and 16gb class4.It could flash wp7 rom and
boot correctly in the past.Today,It can't boot.
How to fix it back to normal to boot correctly into wp7 ?
Sorry,Has anyone known how to fix this problem?
Hi!
Sorry to hear that you have so many problems with your HD2 Am I to understand correctly that you are unable to install any WP7 release now? If that is the case here are a few ideas that have helped me and others in here:
1. Format your SD-card in a Nokia device or in Linux (I do that) and make a fresh install with the desired ROM (please delete SD mbr and activate extra Nand before installing!)
2. Try to flash a WM6.5 release onto you phone first (beware - this will uninstall magldr!)
3. Try to install WP7 without SD card and when you have booted and phone is running ok insert card and make a hard reset using magldr.
If I have misunderstood your question I'm sorry - Please let us know how things turn out for you!
/Anders
and check if HSPL 2.08 installed
Thank ! Anden1986 and dxdy for your answer.
1. Format your SD-card in a Nokia device or in Linux (I do that) and make a fresh install with the desired ROM (please delete SD mbr and activate extra Nand before installing!)
2. Try to flash a WM6.5 release onto you phone first (beware - this will uninstall magldr!)
3. Try to install WP7 without SD card and when you have booted and phone is running ok insert card and make a hard reset using magldr.
Click to expand...
Click to collapse
still stuck at DFT logo.
Even I restored hspl 2.08 to spl2.08 and changed it back to hspl2.08,I also stuck at DFT logo agian.
Normally,I can use wp6.5 and android (nand/sd).
I have problem with WP7 only.
then is microsd card problem... did you try boot without card? if WP7 already flashed just do hard reset and boot without card
Boot without sd card,I already tried,it don't work.
seems problem in ROM....
HI everyone,
This is the first time for me posting a thread here...thanks in advance.
Well I have a HTC HD2 that is a friends of mines. He was trying to change the radio so it could work in another country and managed to brick the phone. He got tired of trying to fix the phone so he gave it to me. I have tried fixing it with a tool kit I downloaded in another thread here. I managed to get it to boot butt it wouldn't get past T-Mobile screen...I kept on messing with it trying to install a ROM and different radios but non will work and wont turn on anymore but still is able to be recognize but PC(not mobile media center) and the last thing I did was task29. It stopped at 99%...still can load bootloader 3 colors but having a harder time getting the phone recognize by PC. Can anyone help me before I get into a deeper hole? If your need any more detail please ask me...btw the phone is running SPL- 3.03 HSPL in boot loader.
to the rescue !!
Jaimelebrone said:
HI everyone,
This is the first time for me posting a thread here...thanks in advance.
Well I have a HTC HD2 that is a friends of mines. He was trying to change the radio so it could work in another country and managed to brick the phone. He got tired of trying to fix the phone so he gave it to me. I have tried fixing it with a tool kit I downloaded in another thread here. I managed to get it to boot butt it wouldn't get past T-Mobile screen...I kept on messing with it trying to install a ROM and different radios but non will work and wont turn on anymore but still is able to be recognize but PC(not mobile media center) and the last thing I did was tasIt29. It stopped at 99%...still can load bootloader 3 colors but having a harder time getting the phone recognize by PC. Can anyone help me before I get into a deeper hole? If your need any more detail please ask me...btw the phone is running SPL- 3.03 HSPL in boot loader.
Click to expand...
Click to collapse
your friend shouldnt have flashed the radio without proper info !!
radio is the only thing which bricks the device !!!
dont worry we'll try to sort something out !!
firstly start with flashing a proper radio !!
http://forum.xda-developers.com/showthread.php?t=611787
download the radio 2.15.50.14 from this thread and flash it !!
NOTE : if you cant flash radio from ur pc, via nbh installer or the toolkit, you can flash it from a memory card !!
just format a normal memory card, put the radio on the card, rename the radio file to LEOIMG.nbh and get to the bootloader screen !!
follow the instructions from there and flash the radio !!
secondly if you want android or wp7-7.5 on ur device !! hspl 3.03 wont work !!
so install hspl 2.08 for that !!
for winmo6.5 3.03 is ok !!
do a task 29 once and flash any rom or magldr(for android or wp7-7.5)!!
good luck .....
thanks for quick reply
I am trying to do what you instructed me.
Didn't work
I tried it on the PC and it sadly stopped @ 96%, now it wont turn on volume down+power. Battery was charged and i didn't turn off. It displayed error 262. as soon as I can I will try it on sd card. Thanks though.
I was not able to install the radio but did in fact get to task29 successfully and MAGLDR Version-1.13. Now my phone is stuck in the Stick together screen. Can anyone help me from here what should I do. thanks I will be waiting for a responce.
Do you still need help cos its really easy to unbrick your phone and I say this because once I flashed 5 different roms in 2 hours or less and my phone wouldn't even turn on and when it did it would get stuck on the tmObile splash screen and restart but I fixed it and now I'm running the best Rom out there lol... reply to this thread and I'll tell you what to do
Sent from my HTC HD2 using xda premium
The thing is that I can't get any ROM's to finish installing...in the SD card the power button does not work...and in the computer the fartest I gotten was 99% but always stops and gives me error ussualy Error 262. Ireally don't know what to do. MY friend said he took it to an Asian Guy...I noticed that the battery S/N does not match the phone...can this have an effect...I haven't been able to flash any ROMS successfully not even the debranded stock. I flashed several phones and installed many different custom firmwares but this phone has been a real challenge...I'm over 2 weeks in...Thanks for the help thus far you guys are the best...
leoimg.nbh won't start to install
Hi everyone,
I have a severe problem with my HTC HD2 after installing a NAND version of android which did not work very well, than wanting to reinstall winmob 6.5 (vodafone) it startet "loading" the leoimg.nbh from the SD-card, but than stayed in this status neverending. So I interrupted (was that the mistake?? :-( }. Now I'm able to start MAGLDR 1.13, am also able to install another NAND version, but with every version I get the message: problem with android.xxx and so on.
I can start the bootloader modus (SPL-2.08.HSPL 8G XE), also connect by USB, but if I try to reload any leoimg.nbh from SD card - it does nothing, just stays in the bootloader modus.
Did I destroy any hardware by interrupting the non functioning "loading"?
Please help, if you can, what I could do now to get a functioning NAND android again!
Many thanks in advance!!!
freak just try the task 29 and u might return everything to normal condition
and for future never interrupt the installation process as u can brick ur device
for the main topic, i can say that ur device is fully bricked and the only way is taking it to the service center or try flashing directly into the hardware, but thats dangerous and requires professional skills
Plz help!
bigtobitobs said:
Do you still need help cos its really easy to unbrick your phone and I say this because once I flashed 5 different roms in 2 hours or less and my phone wouldn't even turn on and when it did it would get stuck on the tmObile splash screen and restart but I fixed it and now I'm running the best Rom out there lol... reply to this thread and I'll tell you what to do
Sent from my HTC HD2 using xda premium
Click to expand...
Click to collapse
Please can you help me.. I did the same thing.. it kept getting stuck at 0% and then i had to wait like an hour and then i tried again.. now its completely dead!
Please tell me what to do..
Thanks
First of all; This steps can solve your problem. But first of all(don't forget to check 2.08.HSL) try to use "Task29" and if it is success, load Radio ROM 2.15.50.14, and load original Winmo 6.5 ROM (Tmous or EU which phone do you use).
If you are stuck somewhere, then;
Download an original ROM for your HTC device from HTC webside.
- Format your SD card like FAT32 primary.
- Take "RUU_signed.nbh" from an original ROM and copy it to your SD card.
- Rename to "leoimg.nbh"
- Reset your device while pressing the volume down button.
Radio ROM 2.15.50.14;
Radio ROM 2.15.50.14
HD2 Toolkit 4.2.0.1; ( contains task 29, magldr and recovery and also HSPL)
HD2 Toolkit 4.2.0.1
it's revived!
powerofthink said:
First of all; This steps can solve your problem. But first of all(don't forget to check 2.08.HSL) try to use "Task29" and if it is success, load Radio ROM 2.15.50.14, and load original Winmo 6.5 ROM (Tmous or EU which phone do you use).
If you are stuck somewhere, then;
Download an original ROM for your HTC device from HTC webside.
- Format your SD card like FAT32 primary.
- Take "RUU_signed.nbh" from an original ROM and copy it to your SD card.
- Rename to "leoimg.nbh"
- Reset your device while pressing the volume down button.
After several attempts to switch on the phone it finally turned on so I immediately installed stock ROM and it didn't get stuck on 0%.. it worked!!
Do you think I should perform a task 29 now or I can just proceed with installing a new radio and then installing a new ROM?
Thanks again mate!
Apparently I need to install SPL 2.08 before trying to install HSPL and then run android.. anyone know where I can find it?
Nevermind figured everything out Thanks anyway
Click to expand...
Click to collapse
If you want to change your ROM with one another like Android NAND ROM or Windows 6.5 ROM, then use this procedures.
For NAND Android ROM; You must flollow this sequence;
first check your device if it is 2.08.HSPL, and format your sdcard ext3 or ext4 and 1gb (which one you must use is pointed out by your Android chief). Copy new Android ROM into your sdcard's FAT32 section. insert it into your HTC device.
1. do task29
2. instal radio rom 2.15.50.14
3. install magldr 1.13
4. do recovery 5.0.2.6
5. do clear cache and dalvik cache.
6. Choose your android ROM .zip file on sdcard, load and enjoy...
For Windows 6.5 Follow this sequence;
first check your device if it is 2.08.HSPL, Format your sdcard like FAT 32 primary partition. insert it into your HTC device.
1. do Task29
2. Install Radio ROM 2.15.50.14
3. Run LeoCustomRUU.exe like "Run as Administrator" which Windows 6.5 rom you chose to use.
Radio ROM 2.15.50.14;
Radio ROM 2.15.50.14
HD2 Toolkit 4.2.0.1; ( contains task 29, magldr and recovery and also HSPL)
HD2 Toolkit 4.2.0.1
ActiveSync
Hi..
I am new here...
I would like to ask about my htc hd2..
I ve installed android 2.3 and yesterday i tried to update to android 4.0 but something went wrong and now my phone can't load anything...
when i tried to install ROM, it shows phone is not connected...
My ActiveSync also doesn't detect my phone... I can't enter to phone settings coz the phone won't load...
Any ideas ?
Thanks...
Zerocool_uia said:
Hi..
I am new here...
I would like to ask about my htc hd2..
I ve installed android 2.3 and yesterday i tried to update to android 4.0 but something went wrong and now my phone can't load anything...
when i tried to install ROM, it shows phone is not connected...
My ActiveSync also doesn't detect my phone... I can't enter to phone settings coz the phone won't load...
Any ideas ?
Thanks...
Click to expand...
Click to collapse
Are you booting into bootloader and connecting the device to your computer so you can get the HTC Sync connection. Just boot into bootloader by holding the volume down button down and poewering on your device. Connect it to your computer via USB and when you see Serial in the white bar of boo5tloader change to USB you have the HTC Sync connection and can flash your device.
I face a very odd problem with my HD2 EU. After years of 2 different versions of Android on nand I decided to reset it to stock(Vol down+power with leoimg.nbh in root of a FAT32 formatted microsd). When I get in bootloader mode there seem to be 2 instances of bootloader. The first 3 colour screen with all the right wordings lasts a second or two then I get a second 3 colour screen with the same wordings. With my Verbatim 8Gb class4 microsd formatted FAT32 and leoimg.nbh (obtained from the original RUU_Leo_HTC_ITA_1.66.408.1_Radio_15.32.50.07U_2.07.51.22_2_Signed_LEO_Ship.exe) in the root directory, the device does not recognize the file and it's not possible to restore the phone to stock, but I can only get into usb connection.
Being able to get in usb mode with the various versions of HSPL (1-2-3-4) I can still change the bootloader. With the HD2 Android toolkit 4.2.0.1 I can install cLK, Magldr, do a Task29 and repartition.
When I use the RUU installer I can install the RUU_signed.nbh that I used to get the leoimg.nbh BUT when I do it, and it does finish gracefully, on the screen that states the currently installed image THE INDICATION OF SUCH AN IMAGE IS BLANK whilst the name of the image to install is the one I am flashing.If I reflash the same image AGAIN (so I know what's on the device) the info of the installed image is never displayed.So after trying the various bootloaders HSPL and SPL and getting the same result you are my only resort.
Has anybody experienced such a problem? It is as if the the bootloader goes through a script that then starts a second "identical" bootloader (I understand that I may seem crazy) that is not capable of recognizing a leoimg.nbh. All my buttons are still working so it's definitely not a button problem. Therefore in a nutshell the question is: if I can't get the device to recognize a leoimg.nbh is there any other way to make it do so, given that I can communicate via usb without problems ?
Earlier today my custom ROM froze. I rebooted the phone by taking the battery out and the phone would only go as far as the Magldr screen where it says "Go Go Go", no matter how many times I tried, the ROM wouldn't boot.
So I wiped my phone with Task29 (even tried installing an original WM6.5 ROM), and tried to reinstall Magldr and a new ROM. However, after I run Task29 and Magldr and turn the phone on, only the white HTC screen displays. I could not get the phone to display the Magldr menu.
Finally after repeating the above a couple of times, I managed to get the Magldr menu to display, but once I install the CM Recovery and enter AD Recovery to install the new ROM, Magldr again gets stuck after displaying 'Go Go Go!'.
I also note that as the phone boots up into Magldr, one of the lines say "nand kernel open failed".
Any idea what is happening and why I cannot boot into Ad Recovery (or my ROM) and always get stuck on 'Go Go Go!'?
it could be a corrupted NAND ic?
have you tried to boot SD?
mengfei said:
it could be a corrupted NAND ic?
have you tried to boot SD?
Click to expand...
Click to collapse
A clean install of the original Windows Mobile 6.5 boots and works. How could I rectify a corrupted NAND in this case?
EViS said:
A clean install of the original Windows Mobile 6.5 boots and works. How could I rectify a corrupted NAND in this case?
Click to expand...
Click to collapse
if that is the case it seems like your nand is OK or there could be just soem bad blocks(i'm just guessing here)
how about giving this a try then run an SD version before going to NAND version
.. run HD2 toolkit
...bootloader
- HSPL 2.08
- Task 29
- Radio_15.42.50.11U_2.15.50.14 >>> not necessary if you have it already
- MagLDR
- MagLDR Repartition 300/ 45
...boot to magldr
- Magldr
- Service
- Boot source > ad sd
Hi,
I want to instal WP7 on my HTC HD2.
In the tutorial i use i should use the Rom update utility to get MAGLDR on my phone.
When i try to use this utility i don't get further than 0% and after some time i get a error (error 626)
What i did is:
- I reseted my HTC HD2.
- I started the Rom update utility. It says that i need a update from 1.66.404.1 to 2.00.000.0.
- So when i start this it will restart my phone and show me a progres bar.
This will stay on 0% and after 10 minutes the utility gives me a message that says:
You connection is lost(error 626). Than i need to "recover" my phone by taking the battery out and put in in again.
When i do this it wel restart my phone with the WM6.5 so nothing happend.
I tryed the following things:
- A different usb cable and usb port.
- redownload the Rom Update Utility from this site.
- Hard reset my phone.
Nothing happend a still geth the same error.
Does someone know how to fix this?
Or is there a defferent way to install WP7 on my HTC HD2.
Thanks,
Maarten
read tutorial from my signature
I will try that thanks.
I finished step 0.5 and 1.
But when I am at the line "When phone boot in MAGLDR use:"
I get stuck.
The MAGLDR is installed but when the phone restart i get stuck on the white HTC screen.
Any clou what i should do next?
if not boot, press and hold power button to start magldr....
I tryed it but it wont do anything else than go to the white boot sreen with the Green HTC logo.
I tryed to press the power button for a long time and while he is booting.
Butt notting more than te boot screen shows.
The only way to start the phone again is to remove the battery.
I can get in the "red-green-blue-white screen"
I already tryed to reinstall the magldr. But no luck.
And what do you meen with "in not boot"?
The only thing it does do is boot to this logo and that's it. So its always booting when i turn it on...
"if not boot to magldr"
which HSPL you have installed on device?
try install WM6.5 first then install magldr....
first time when phone boot after magldr flashed, must boot to magldr automatically
I have HSPL2.08
It doesn't start the magldr automatically.
Even if i hold the power button. It just starting with a white boot screen with HTC logo.
Don't know how to install wm6.5 again.
Please help. I would like to use my phone tomorow again.
Edit:
Maybe it's bricked...
boot to threecolor screen and flash WM6.5
Ok I flash back to WM6.5
What to do now?
Follow the instructions again i asume.
Anyway many thanks for your help!!!
yes, after flash, install magldr and continue...
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
you cant flash WP7 without magldr menu (setting options and enable USB flasher in magldr)...
yes this magldr is ok...
http://forum.xda-developers.com/showthread.php?t=893618
to be sure, which version of HD2 you have?
also check data in bootloader screen (threecolor)
Data in bootloader screen:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Version:
I know i don't have the t-mobile version.
HTC HD2 T8585
MasterMaarten said:
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
Click to expand...
Click to collapse
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
hjhjhj said:
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
Click to expand...
Click to collapse
I used the manual from dxdy:
STEP 0.5 - from same beginning, WP7 never or not installed on phone
- If needed (if Android NAND installed, or if any error during flash
process, erase NAND with Task29). Flashing WM6.5 not needed.
- if you have SIM locked phone and want unlock with code, you can this only in WM6.5
- insert formatted microSD card to FAT32 in phone
- flash radio if you want (if flash version available) or use radio upgrade during ROM flashing (put radio file
part00.bin in data.zip file before ROM flash)
STEP 1. - when HSPL and/or MAGLDR not installed
- Flash HSPL 2.08 if needed (put device in bootloader before Flash:
press and hold Volume down + Power button)
- Flash MAGLDR 1.13 (put device in bootloader before Flash:
press and hold Volume down + Power button)
Click to expand...
Click to collapse
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
MasterMaarten said:
I used the manual from dxdy:
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
Click to expand...
Click to collapse
you should do task29 whether you have android or not....between flashes even if wp7. task29 cleans out the memory area where the OS will reside.
as for the radio...radio thread for the TMOUS radio is here:
http://forum.xda-developers.com/showthread.php?t=1111613
more than likely you shouldn't have to flash a radio, but it won't hurt. only have to do it once.
in order to use the rom flash utility...you have to go into magdlr main screen...scroll down to and select 10. Services, then select 5. CleanMBR, and then 4. Uselast24NAND. Finally, back at the main set of options select 5. USB Flash.
Then you kick off your DWI.exe in admin mode.