I fixed my wet phone !! - Epic 4G General

I dropped my phone in the toilet last night. I immediately pulled out the battery and dried the exterior as much as I could and under the battery compartment.
Most people put thier phone in a bag of rice and wait for it to dry and hope for the best.
If you can't wait 48 hours to get your phone to dry and you're not afraid of taking apart small electronic assemblies. This is the way you wanna go. Plus you have the comfort of knowing that Your phone is completely clean and dry before you turn it back on.
This morning I went online to find disassembly instructions. I used this video: http://www.globaldirectparts.com/Sprint-Samsung-Epic-4G-Galaxy-S-SPH-D700-Take-Apar-p/taprtvdo029.htm
This video helped incredibly for disassembly. I would have destroyed my phone were it not for this. So I took the phone all apart according to the video. Dried as much as I could with a cloth and blew all the parts out with some canned air duster. I have hot air heat in my house so I put all the parts on a rag and put them on top of the air register with a box over the top to trap some of the warm air to accelerate the drying process. I let the parts dry out for about 6 hours with this air register deal. Then I reassembled the phone. There was no video for reassembly so I had the to play the video from the end in 30 second bites to make sure I got all the connections back correctly.
There was one part where the ribbon cable attaches to the led screen which I screwed up. The connectors actually have tiny little lockdown clips which weren't shown in the video. In the video they just pulled the ribbon out of the connector without ever unlocking the tiny levers.
So I had to disassemble the phone and reassemble it again, because the screen wouldn't come back on. I got it all back working again the second time around.
I had purchased this phone on ebay and it was in excellent condition when I bought it. But, when I opened this thing up there was noticeable corrosion on the circuit board which leads me to believe this thing took a bath before I bought it. So I brushed off the corrosion with a soft new toothbrush before i put it all back together and the circuit board looked brand new.
I know this is a long post but I'm hoping that someone will find this in a search someday and it'll help them out.

This is why I'm going to buy samsung again
sent from my always aosp epic

Xalky said:
I dropped my phone in the toilet last night. I immediately pulled out the battery and dried the exterior as much as I could and under the battery compartment.
Most people put thier phone in a bag of rice and wait for it to dry and hope for the best.
If you can't wait 48 hours to get your phone to dry and you're not afraid of taking apart small electronic assemblies. This is the way you wanna go. Plus you have the comfort of knowing that Your phone is completely clean and dry before you turn it back on.
This morning I went online to find disassembly instructions. I used this video: http://www.globaldirectparts.com/Sp...Galaxy-S-SPH-D700-Take-Apar-p/taprtvdo029.htm
This video helped incredibly for disassembly. I would have destroyed my phone were it not for this. So I took the phone all apart according to the video. Dried as much as I could with a cloth and blew all the parts out with some canned air duster. I have hot air heat in my house so I put all the parts on a rag and put them on top of the air register with a box over the top to trap some of the warm air to accelerate the drying process. I let the parts dry out for about 6 hours with this air register deal. Then I reassembled the phone. There was no video for reassembly so I had the to play the video from the end in 30 second bites to make sure I got all the connections back correctly.
There was one part where the ribbon cable attaches to the led screen which I screwed up. The connectors actually have tiny little lockdown clips which weren't shown in the video. In the video they just pulled the ribbon out of the connector without ever unlocking the tiny levers.
So I had to disassemble the phone and reassemble it again, because the screen wouldn't come back on. I got it all back working again the second time around.
I had purchased this phone on ebay and it was in excellent condition when I bought it. But, when I opened this thing up there was noticeable corrosion on the circuit board which leads me to believe this thing took a bath before I bought it. So I brushed off the corrosion with a soft new toothbrush before i put it all back together and the circuit board looked brand new.
I know this is a long post but I'm hoping that someone will find this in a search someday and it'll help them out.
Click to expand...
Click to collapse
Have to say thank you very much... wasn't paying attention and my 17 month old took my phone and put it in a glass of water!!! Went to the video you linked and got it taken apart. Dried the way you specified and now all is well!!!!!!!!! Thanks so much! Probably would've been without a phone for a bit if it wasn't for this!
Sent from my SPH-D700 using Tapatalk

flastnoles11 said:
Have to say thank you very much... wasn't paying attention and my 17 month old took my phone and put it in a glass of water!!! Went to the video you linked and got it taken apart. Dried the way you specified and now all is well!!!!!!!!! Thanks so much! Probably would've been without a phone for a bit if it wasn't for this!
Sent from my SPH-D700 using Tapatalk
Click to expand...
Click to collapse
I'm glad this helped somebody. I just didn't think it would be so soon .
Sent from my SPH-D700 using xda premium

Xalky said:
I'm glad this helped somebody. I just didn't think it would be so soon .
Sent from my SPH-D700 using xda premium
Click to expand...
Click to collapse
Yep and worked like a charm! You my friend are a life saver!
Sent from my SPH-D700 using Tapatalk

Related

Dropped my hermes in the toilet

Hi, dropped it in the toilet today.
Been drying it off for 7 hours in front of a heated fan. Tried to turn it on, the HTC screen comes up but it's really faint so I took the battery out straight away.
What are the chances of it working again?
ethos84 said:
Hi, dropped it in the toilet today.
Been drying it off for 7 hours in front of a heated fan. Tried to turn it on, the HTC screen comes up but it's really faint so I took the battery out straight away.
What are the chances of it working again?
Click to expand...
Click to collapse
So you took the battery out after the 7 hours? - Not good in such cases the first thing to do is always to take out the battery - However I had a similiar problem a while ago - but with a nokia phone - local electronics store took it to repair it for free but **** happens I sim unlocked it and they told me I had to pay 200 bucks for the repair - I googled a bit and found that you should take the whole device apart and try everything seperated then put every single part into ethanol (I think it was ethanol not shure :S) over night and in the morning let it dry - repeat up to 5 times - if no hardware was fried everything should work again - my phone worked again
No, I took the battery out after like 20 seconds.
I then took it apart and wiped it off and put it in front of a heated fan for about 7 hours!!!!
I dropped my 8125 in a cup of Vodka and Sprite and took the battery out right away. Let it dry out for 12 hours, turned it on and got a white screen. Took the battery out again and decided to order an 8525 to replace it thinking it was dead. Hours later, I tried to start the 8125 again and it magically started working. Guess it was a long hangover but just shows that given enough time, it might come back.
WELL... left it in the airing cupboard overnight.
It now turns on fine, the screen is working but I can still see a little bit of water but other than that it all works fine.
Going to leave it in front of the heater again today to hopefully clear the last of it up.
CHUFFED!
To my home fish tank
My old sony eriksson drop into my fish tank.!!!
Initially it don't work.
I put phone and battery apart inside a big cup and covered it with rice and voila..., after two days it was like new.
It was an old trick form my mother.
Hope it help
Hints and tips available.
The best way to recover a water damaged device is to get yourself a good denture brush and some denatured alcohol. Take the device apart down to its base components. The board, LCD board components for your soft keys ect. The biggest problem that I've experienced is that it sometimes fries out the flash for the camera which will stay on. Now with your denatured alcohol and your brush just gentle scrub the board components and the connections this will absorb the moisture upon evaporation. Also its always good to have a nice heat gun thats also a good way to reflow contact points on the board say you have connection issues with your mini USB port. I've been doing electronics repair on PDA and cell phone devices for sometime. So anyone who has questions feel free to ask. I hate hearing about people who dump 200 dollars for a repair that you can fix by spending 5 dollars.
I would like to start a thread but since my membership is at the junior status I dont see it being read. But I will post it anyway.
C Brown said:
...I would like to start a thread but since my membership is at the junior status I dont see it being read. But I will post it anyway.
Click to expand...
Click to collapse
Sorry, I don't follow your logic. Post up what you know, based on your experience. I assure you it will be gratefully received.
Do a separate thread though, so it can be turned into a sticky by the mods.
Thanks
WB
Give it more time. I say 2-3 days to completely dry then try.
C Brown said:
The best way to recover a water damaged device is to get yourself a good denture brush and some denatured alcohol. Take the device apart down to its base components. The board, LCD board components for your soft keys ect. The biggest problem that I've experienced is that it sometimes fries out the flash for the camera which will stay on. Now with your denatured alcohol and your brush just gentle scrub the board components and the connections this will absorb the moisture upon evaporation. Also its always good to have a nice heat gun thats also a good way to reflow contact points on the board say you have connection issues with your mini USB port. I've been doing electronics repair on PDA and cell phone devices for sometime. So anyone who has questions feel free to ask. I hate hearing about people who dump 200 dollars for a repair that you can fix by spending 5 dollars.
I would like to start a thread but since my membership is at the junior status I dont see it being read. But I will post it anyway.
Click to expand...
Click to collapse
+1, the best way to clean your water damaged device and have hope of it working again.
It may take a while to work properly again; my 8525 went into water not once but twice! The first time I thought it was dead--lights on but only white screen. Had instantly removed battery and opened it up as much as I good and took some canned air to it. Kept checking it over the next week without success so went and bought another.
Anyway, about 3 weeks after the dunking I put the battery back in and on a whim turned it on and surprise!, works fine. This became my back up phone that I later took to Africa with me where I proceeded to drop it in a toilet. Since the air temp was 130 degrees it didn't take long to dry out and it's still kicking!!! Important point is to immediately remove the battery, take the device apart as much as you can, dry completely over a few days then attempt to turn on.
Hope this helps,
Steve
Mine went into the toilet this morning. I have disassembled it according to the directions (http://inuchanbt.blog54.fc2.com/blog-entry-100.html) and put it all back together after cleaning surfaces and connectors with alcohol.
It powers up now, which is far better than it was doing just after I fished it out of the pot. USB connection works, speaker phone works, etc.
However, touch screen does not. If I hold the screen at a certain angle I can see a faint outline of where water has creeped into the screen about 1/2 of the way across. Touch screen worked decently on first power up but now it does not work at all. All buttons work okay.
I am going to disassemble again after work and inspect the screen more closely. Hopefully will save me from having to replace the machine!
speckledpig said:
I am going to disassemble again after work and inspect the screen more closely. Hopefully will save me from having to replace the machine!
Click to expand...
Click to collapse
...and if its just the screen that doesnt work, thats a cheep, easy fix!
I just reassembled after cleaning again and touchscreen works.
I am going to evaluate tonight and we'll see!
Those disassembly photos were EXTREMELY helpful; thanks MUCH to whoever originally posted them.
I managed to spill an entire beer on mine, turned it off and let it dry as above,. everything worked great but the scroll wheel started to get confused as to which way i was scrolling it, cleaned as above with alcohol and no problems. Actually I have found that the scrollwheel on my tytn gets hinky every couple of months or so and have taken to cleaning it regularly, onve youget over the inital fear of opening up your baby it's a breeze.
That reminds me of my old Siemens SX1 *chuckles* i went swimming in the sea and i forgot i had it in my pocket.. after 15min i suddenly felt it.. I dashed to the shore and pulled it out of my pocket.. And it was still running! While water was dripping out!
And to be honest, i never cleaned it afterwards. i just let it dry in its current state.. but hell that SX1 has endured some hazzards, and its still working ^^
Altho a bit oldfashioned now
Anyway this is pretty offtopic i know sorry bout that
Hmmm. The keyboard doesn't work. It worked yesterday. Neither does the screen rotate when I slide.
I guess it will have to come apart again.
The connector had popped loose, or maybe I didn't connect it at all yesterday.
Anyway, works great, and the water in the backlight is noticeably less. It is drying on its own.
Fully functional 8525!! YAY!!!!!
O dropped my Atom in a mop bucket once.
Took battery out and tried to dry but was FUBAR. Sold it on eBay for $90AUD =D used that money to get a Hermes for $400AUD
ethos84 said:
Hi, dropped it in the toilet today.
Been drying it off for 7 hours in front of a heated fan. Tried to turn it on, the HTC screen comes up but it's really faint so I took the battery out straight away.
What are the chances of it working again?
Click to expand...
Click to collapse
Did you flush before dropping the phone? If not, make sure to clean out all the "brown bits"

[Q] Waterproof Epic!!

<---- Idiot jus dropped his epic in sum water & of course it's not working!! I dried it out w/ a towel & blow dryer after it happened. When I connect the battery the keyboard keys still lights up, but when I press the power button all I hear is a ringing type noise (sounds like a fan spinning) and no bootup. I cannot boot into CWM or Download mode either. Has anyone experienced this or found a solution w/o having to replace the whole phone.
** Also, my battery has the red marking on the top of it stating it's been wet.
EDIT: If I plug in my usb the LED light comes on, but it's blue & my phone was @ 80% when I dropped it.
Thanks in advance!!
UPDATE: [ I couldn't wait the 48 hours!! (36 Hours) -- LoL ] I just removed my phone/battery from the rice bags & everything is working!! Yes, even the battery is good @ 72%!! I can't believe it worked!! Thanks Matrix!! And thanks to everyone for your great suggestions!! This phone is truely EPIC!!
Turn it off and remove the battery now!!! Do not put the battery back in.
You're going to mess it up by turning it on when things are shorting out!
Take the battery and the phone. Put them (separately) in a zip lock bag full of rice. Wait a day or two. Then try it out.
PS: Everyone should ingrain themselves in this reflex: If your phone hits water, remove the battery NOW. Do the rice trick, and try it later. Resist the urge to see if it still works.
Thanks for your quick replay & suggestion matrix!!
I am currently trying your method, but I'm hoping I didn't further short anything on the circuit board by trying to get it to work earlier.. It sounds like a good plan because the rice will absorb the water and probably be ready for consumption in a day or two!! LoL
Forget the bag of rice, you need to take the phone apart immediately, to the last screw and board and wipe down everything with alcohol and blow it out and dry it with a hair dryer. Otherwise even if you get it to work in a couple of days, corrosion will start to build up on the contacts of various things inside and you'll end up having to get another phone.
And this is why that extra $7.00 a month is worth it.
hdnet1 said:
Otherwise even if you get it to work in a couple of days, corrosion will start to build up on the contacts of various things inside and you'll end up having to get another phone.
Click to expand...
Click to collapse
Forget about taking it apart... you're garonteed t miss somthing and the corrosion will kill it anyways. I know for a fact
Sent from my SPH-D700 using XDA App
hdnet1 said:
Forget the bag of rice, you need to take the phone apart immediately, to the last screw and board and wipe down everything with alcohol and blow it out and dry it with a hair dryer. Otherwise even if you get it to work in a couple of days, corrosion will start to build up on the contacts of various things inside and you'll end up having to get another phone.
Click to expand...
Click to collapse
Soo .. which 1 should I do?? They both sound right to me!! I checked on YouTube & I seen a vid about using the rice technique, but no vid about completely taking it apart to dry off the components??
styckx said:
And this is why that extra $7.00 a month is worth it.
Click to expand...
Click to collapse
I do have the warranty -- Doesn't water damage void it?? They can tell by the red marking on the battery.
No, just means you gotta pay them whatever the current fee is for water damaged phones. Used to be 50 bucks, but I think the crooks doubled it. As for taking it apart, forget about that nonsense. Bag of rice for a couple days, take it out, if it boots up you are fine.
muyoso said:
No, just means you gotta pay them whatever the current fee is for water damaged phones. Used to be 50 bucks, but I think the crooks doubled it. As for taking it apart, forget about that nonsense. Bag of rice for a couple days, take it out, if it boots up you are fine.
Click to expand...
Click to collapse
Cool .. I really didn't wanna take it apart. I would have prob did more damage to it!! LoL I will wait out the 2 days & post back w/ an update then.
Thank you all for your help!!
CRC Mass Air Sensor Cleaner
You can find it at auto parts stores, its an electrical component cleaner that displaces water, removes grime, grease, corrosion and dries with no residue.
You have to take it apart to use it and don't get it on plastic stuff. CRC makes several different electrical component cleaners and some of them will eat plastic so be careful with it.
Saved my Sprint Hero with this stuff after it landed in a puddle and spent about two minutes fully submerged in the water before I found where it landed. Luckily I was home, ran inside, took it apart and grabbed a can of CRC I had in the garage on a whim.
Granted, I never tried turning it back on while it was still wet, that is often the killer for wet electronics.
Just figure that its dead, whatever you do to it at this point isn't going to hurt it anymore but I would HIGHLY recommend taking it apart to make sure you get all the moisture out of it. I don't put much faith in the rice trick
D`Nyed said:
CRC Mass Air Sensor Cleaner
You can find it at auto parts stores, its an electrical component cleaner that displaces water, removes grime, grease, corrosion and dries with no residue.
You have to take it apart to use it and don't get it on plastic stuff. CRC makes several different electrical component cleaners and some of them will eat plastic so be careful with it.
Saved my Sprint Hero with this stuff after it landed in a puddle and spent about two minutes fully submerged in the water before I found where it landed. Luckily I was home, ran inside, took it apart and grabbed a can of CRC I had in the garage on a whim.
Granted, I never tried turning it back on while it was still wet, that is often the killer for wet electronics.
Just figure that its dead, whatever you do to it at this point isn't going to hurt it anymore but I would HIGHLY recommend taking it apart to make sure you get all the moisture out of it. I don't put much faith in the rice trick
Click to expand...
Click to collapse
True, it prob is near dead at this point. I will try this solution if the rice trick doesn't work tomorrow. Hopefully, one of these solutions work out!! Thanks for your input!!
It's def dead if u already tried to turn it on.
Just tell them you dropped it off the side of a boat.......then you wont have to show it to them
My buddy dropped his epic4g in the toilet bowl, he was paying insurance ($7.99 a month.) He did the samethings you did and did the rice trick and nope didn't work. Ended up calling sprint and spending 150 I think for a replacement phone.
- Its just going to be Epic!
Silica Gel packs are better than rice if you have any of those.
BUMP!! Please read my update to my OP!! Rice is the not only good for eating!! LoL

Swam with my phone for 20 min

On my last day on holiday I forgot to take my phone out of my pocket before going to the swimming pool. Now it's soaked and looks bricked. Does anyone knows if there it's a chance of it working after it's dried up.
If the phone was off and the battery was removed as soon as possible. Another major factor is how pure the water is - sea water will kill your phone unless you wash it out with water with no (or as almost none) salts in it.
The phone was to be allowed suffient time to dry out. Placing it under a gentle heat (ie near a lamp) and with those silicon bags that it equipment comes with or with rice. You are normally talking about a week for drying out time.
I've heard of dripping wet phones drying out and being okay, so it's a possibility.
There's all the usual airing cupboard/bowl of rice/little crystal packs you get in your trainers/bag of salt suggestions, but I think the most prominent one is to be 100% sure that ALL moisture has gone before you try turning it on again.
Have a search through the forums, and not just this phone as this is obviously not a phone specific problem. There's plenty of advice out there.
Good luck mate - I hope you get it working again.
TA123 said:
On my last day on holiday I forgot to take my phone out of my pocket before going to the swimming pool. Now it's soaked and looks bricked. Does anyone knows if there it's a chance of it working after it's dried up.
Click to expand...
Click to collapse
open the back panel take evry thing out
dray it
dray the phone from back with an hair dryer with medium heat
for one hour
put it outside in the open for 4 hours
again one hour with hair dryer
and pray a lot
this is what save my nokia n95 ....so be optimistic
In my case I was saving a child from drowning ...so maybe it was an angel that thought it is not a good day to kill my phone
(try doing a good thing before the process)
good LUCK
20min is a long time for the phone to be in the water
It will also depend on if the phone was on or off when it went for a dip.
if it was off, there is a small chance it could be ok, leave it for a week to air and then cross your fingers.
if it was on, id take a guess that your goose is cooked.
sorry to hear bud.
Thanks a lot for all support! Well the phone was on :-( but the water was fresh. Anyway we have already checked out so no access to a hair dryer. Rice is not available until we're back to England this evening. Will report back if the phone survives.
Dissamble your phone completly (tutorial on youtube), place the mobo in a oven @ 100 degrees C for 5 a 10 min
Try first to dry your board with a hairdryer
I once fixed a friends (cough) iphone that was full of dirty water. Stripped it down, put the main components in clean water to wash it out, then put in a 50 degree oven for an hour. Left if over night then reassembled. Worked a treat afterwards, so there is hope. The secret is to give it plenty of time to dry out.
Use distilled water to rinse. Or even better, isopropanol; no baking needed.
Sent from my GT-I9100M using XDA App
it looks it's fried :-( I disassembled it and dried up but it does not show any signs of life. Will try to call my travel insurance company tomorrow to see if it's covered.
hahahahahahahhahahahahahahahahahahahahah
LMAO!
TRULY SORRY for loss, but your story cracks me up.
ops.. use rice for save it.
emeky said:
ops.. use rice for save it.
Click to expand...
Click to collapse
It was covered with rice for the whole night without any results
U need to cover it with rice and put it in an box u can close so no air would come in
Sent from my GT-I9100 using XDA App
just_nos said:
U need to cover it with rice and put it in an box u can close so no air would come in
Sent from my GT-I9100 using XDA App
Click to expand...
Click to collapse
it should be perfectly dry after everything that has been done to it.
I would be tempted to take it apart and leave it for a week it 2 to dry out. There's a good chance it will work again as long as you don't turn it on while its still wet. If it was salt water or water with chlorine wash the phone with clean water well while in pieces. It shouldn't cause any damage doing this. Its best to remove all salt & chlorine as to prevent long term damage.
Sorry to be the dictionary police but its kinda a habit of mine, swimmed with makes no sense, I think you were aiming for swam.
Sorry about your phone dude, I know its a pain when it happens. Good luck with it all.
yusuo said:
Sorry to be the dictionary police but its kinda a habit of mine, swimmed with makes no sense, I think you were aiming for swam.
Sorry about your phone dude, I know its a pain when it happens. Good luck with it all.
Click to expand...
Click to collapse
Oh, I was so heart-broken to watch my grammar
TA123 said:
it should be perfectly dry after everything that has been done to it.
Click to expand...
Click to collapse
It takes a Minimum of 2 weeks to cure a water damaged phone. If it has salt in it, it wont work at all. IN such a case you should have rewashed it with clean water. You also need to keep it air tight with DRY rice inside a airtight box for 1 to 2 weeks. This will make sure all the fluids are extracted from the machine.
It can feel dry, but it does not mean it actually is. Also, DO NOT, I repeat DO NOT charge the phone with the battery in it after a water accident for the first time again.
Well, both of my insurance policies explicitly exclude mobile phones .
So it is now like either the phone will survive or I will have to use my old Hero for the next 12 months.
So I washed it again to make sure no chlorine left and put it in a tightly closed box with a lot of yummy rice
Anyway, I do not hold my breath. I think I fried it when I thought it is dry and was trying to switch it on.

Water Damage

So I dropped my N1 in water. Took out the battery as soon as possible then I dried what I could with a towel.
After this I tried hours of the rice method (putting my N1 in a bag of dry rice to dry it out). And I was able to successfully boot up my phone again, almost everything works fine but the digitizer/touch screen has some issues.
The rightest side of the screen, about an inch worth is completely unresponsive, so if I load up my app drawer and try to click anything on the right it won't work at all just so you know what I mean.
What can I do about this? Is this a simple fix? Do I just need a new digitizer? Or is it something else?
Water damage can affect anything. Luckily the digitizer is only $25 and there are tons of videos on how to disassemble the phone.
Sounds to me like you've still got a short somewhere inside your N1. Here are some suggestions.
1. Rice is a desiccant, it takes a LONG TIME to actually dry-out something like the internals of a phone. If you can part with the phone for that long, I'd suggest leaving it in the rice for more like 72hours!!
2. If you can't give it that much time, and you've got some tools, skills and a willingness to take apart your N1? Then search youtube for "nexus one disassembly" and take it apart, being extra sure to manually dab dry all areas possible (especially in the digitizer area as you've stated issues around there).
3. Finally, if those steps don't work, you're looking at a digitizer replacement. Which, if you've already taken apart your N1 from step #2, will be an easier swap out for you to handle.
My N1 too went for an unwanted splash as well. Total submersion for a good few seconds as I had to fish it out. Water had gotten into the screen, EVERYTHING was wet.
I had the tools and the mindset that my N1 was likely dead anyway so taking it apart couldn't hurt any further. So I took it completely apart, used a paper towel to dab dry everything possible that I could. Then I left everything out on the table overnight to dry.
Next morning I put it all back together and to my delighted surprise everything worked!
Our N1s are troopers! I'm confident you can bring yours back to full life!
Good luck!
Thanks for the responses!
I will definitely try taking it apart and I'll post back soon on the outcome, if I get lazy though I'll just buy a new digitizer.
How is it possible that water doesn't hurt your N1? It's completely incredible. Few years ago i had a samsung player (my son in fact) that was in contact with water (no immersion!!) and after drying for a week (air then hair-drier!) it was impossible to get it on again.
Is N1 that strong!! So lucky you are!!
abccg said:
Thanks for the responses!
I will definitely try taking it apart and I'll post back soon on the outcome, if I get lazy though I'll just buy a new digitizer.
Click to expand...
Click to collapse
Well if you buy a new digitizer you're gonna have to take it apart anyway haha.
Sent from my Nexus One using Tapatalk
abccg said:
So I dropped my N1 in water. Took out the battery as soon as possible then I dried what I could with a towel.
After this I tried hours of the rice method (putting my N1 in a bag of dry rice to dry it out). And I was able to successfully boot up my phone again, almost everything works fine but the digitizer/touch screen has some issues.
The rightest side of the screen, about an inch worth is completely unresponsive, so if I load up my app drawer and try to click anything on the right it won't work at all just so you know what I mean.
What can I do about this? Is this a simple fix? Do I just need a new digitizer? Or is it something else?
Click to expand...
Click to collapse
Use rice is a real bad idea, hairdryer is the best and i'm pretty sure you can find one in your house or borrow one from your neighbour
Seems like there is still a short in your cellphone and i would recommend you call your manufacturer for this. Anyway, it's risky to repair a cellphone by yourself.
A little over a year ago I washed my Nexus One in the washing machine. Extra bleach, long cycle with an extra rinse cycle since it was a bunch of dirty clothing.
I remembered it was in my pocked when I went to remove my clothing, I was sure it was dead.
I pulled the battery and put the phone on the dry air vent of my dehumidifier for two days. The vent blew warm, completely dry air directly into the open back of my phone.
I popped the battery back in and it's been working like new ever since. The camera colors are ever so slightly off, however.
Let the phone dry out before you try to turn it back on.
Recently had the same issue. In my case was a bit easier.
What I did - removed back cover, battery, SIM, sd-card..
Switched my laptop and loaded it with compiling linux kernel. Then decoding HD video with handbrake. The aim was to get a constant flow of warm air (abt 70 degrees Celcius). And I put my phone close to vent fan out of my laptop. It is not overheating too much (like you can with air dryer).
I had a water damage as well, sliped with phone into the while geocaching. The salt walter wasn't good for my phone... :-(
CCpotter said:
Use rice is a real bad idea, hairdryer is the best and i'm pretty sure you can find one in your house or borrow one from your neighbour
Seems like there is still a short in your cellphone and i would recommend you call your manufacturer for this. Anyway, it's risky to repair a cellphone by yourself.
Click to expand...
Click to collapse
I always thought rice, particularly instant rice because it is so absorbent, or any dessicant was a good strategy.
On the other hand, hair dryers seem a very bad idea. Heat from the dryer can be damaging, but the real damage from a hair dryer is that is sends the air at a strong velocity and it blows the water further in the device.
CCpotter said:
Use rice is a real bad idea, hairdryer is the best and i'm pretty sure you can find one in your house or borrow one from your neighbour
Click to expand...
Click to collapse
cyberstoic said:
I always thought rice, particularly instant rice because it is so absorbent, or any dessicant was a good strategy.
On the other hand, hair dryers seem a very bad idea. Heat from the dryer can be damaging, but the real damage from a hair dryer is that is sends the air at a strong velocity and it blows the water further in the device.
Click to expand...
Click to collapse
Rice is actually a very good thing to use just like cyberstoic says. It sucks the water into the rice and gets it out of the device.
The reason he listed for the hair dryer is valid, but it isn't the main reason. The main reason is that the hair dryer will just cause the water to evaporate, but that doesn't necessarily mean that the super humid air will leave the device, so as soon as it cools back down, you will still have that moisture in there.\
This is why rice or other desiccants (like all those silica gel packets that come with a lot of packaging) are used. They actually pull the moisture out of the device.
Rice worked for me when my N1 spent a night soaking in seltzer. (not completely submerged, but enough to get a big batch under the screen) But first I used a vacuum to suck out as much of the seltzer as I could. Then I put it in rice for about 30 hours.
Sent from my Atrix 2 using Tapatalk...
cyberstoic said:
I always thought rice, particularly instant rice because it is so absorbent, or any dessicant was a good strategy.
On the other hand, hair dryers seem a very bad idea. Heat from the dryer can be damaging, but the real damage from a hair dryer is that is sends the air at a strong velocity and it blows the water further in the device.
Click to expand...
Click to collapse
What about the dirt in the rice? If you use rice to dry those water inside, the dirt with rice will melt with the water inside and make damage to your elements.
If you use hair dryer in a proper way, it can dry your water inside without causing any damage. Have seen after-sale repair workers do this many times.
CCpotter said:
If you use hair dryer in a proper way, it can dry your water inside without causing any damage. Have seen after-sale repair workers do this many times.
Click to expand...
Click to collapse
Did you read my response at all? While it is possible for the hair dryer to fix the problem, it can also cause the problem to remanifest itself if that humid air doesn't actually leave the casing. That is the point of the rice. Dirt in the rice is irrelevant. We aren't talking about that much water, and the phone is still in its casing. The rice is just removing the moisture from the air.

dropped my v20 in a puddle on monday... UGH

Hey all,
I dropped my V20 in a puddle on monday. It spent about 5 seconds submersed. I did remove the battery and put it in front of a airconditioner fan. When I got home I put it in a bag of rice. Today the screens backlight is messed up. The only area that lights up is the upper right. The rest is displaying info but no backlight unless I tap the phone hard on a flat surface. Then entire screen lights up for a while then it goes back to the upper right being lit up. I put it back in dry rice tonight. Everything on the phone works 100% but the backlight. What can be done. I dont want to buy another phone and I dont have insurance.
Leave in the rice bowl for another day and then check ✔
Sent from my LG-H990 using Tapatalk
Weren't these phone supposed to be almost waterproof?
phatmanxxl said:
Weren't these phone supposed to be almost waterproof?
Click to expand...
Click to collapse
V20 never meant to be waterproof. G6 yes.
Sent from my LG-H918 using Tapatalk
I found success a few years ago by shoving my phone with the battery cover and battery removed into the flexible tubing of a shop-vac (no attachments on the end) and running it for about an hour. I did this immediately after taking it from the toilet it dove in; this sucked the air through it and pulled internal water out, rather than blowing air on it and not bothering the internals much at all. After that I put it in rice for 2 days to try to make sure all the water is out and evaporated. From some of my friends in the electronics field I hear it's the corrosion that hurts more than the water, and turning on the phone before all water is removed is about the worst move you can make. This may be more useful info for next time, but wait until all drying techniques are employed before putting in the battery and turning on the phone/tablet. Good luck.
youll need to open it, and take denatured alcohol and clean all the parts using a tooth brush, each time u put battery in/charge ur ruining the board and circuitry, need to clean off the corrosion before causing more damaged, but sadly to say if its been a few days and been in rice/dried up when you open it i wouldn't be shocked you'll find the cable that connects ur screen is fried at the board side and wont be repairable.
I forgot about that. This phone is easy to take apart. Iirc, it's 16 screws or so.

Categories

Resources