Database Users

Little Cap covering Car Antenna Connector missing,suggestions?

Don't know how it happened, but just looked at the back of my Tytn, and it is missing that little plastic/rubber cap that goes over the Car Angenna Connector (that's what they call it in the manual). Can anyone suggest how I could get/buy a new/used one ? I haven't seen any posts of this type of thing happening to anyone else..not sure why? I now realize that it must be a removeable cap. I am surprised that nobody else, seems to lose theirs. Anyways, any suggestions are appreciated. It certainly shouldn't cost a fortune for such a puny thing!..

see if you can find it here..
good luck.

If all else fails, try the end cap from a Bic Stic ballpoint pen -- the little plastic bit plugging the non-writing end of the pen's barrel. Should be pretty close to the right size.

Thank you for your suggestions
Will try your link,, and try your Bic suggestions.

One thing you could also do is use a piece of black electrical tape to cover the antenna hole underneath the battery door. When you put the battery door back on, it will look just as it did before as the tape will be underneath it.

I think I found an almost perfect substitute
I went to the Home Depot and bought a package of Self-Adhesive Foam and Vinyl Pads. Different sizes, but the one that I bought had black ones, different sizes. I just had to trim ,make a smaller circle out of any of the black ones, to slightly ,but barely overcover the hole, then I placed back the back cover on top of it. You should make sure that the pad isn't too thick. Mine were fine. I suppose, instead of even taking off the back, you could approach it by keeping the back on, cutting a round piece that would fit snuggly into the hole. Too boot, the sticky part, should more or less adhere to the exposed bits that are in the hole. I prefered the other way, because it adhered to the actual back of the phone,near the hole a lot better. Hopefully I helped those people find a better way, than using bic pens blunt end. I tried that , but not nearly as good as my method.

dented chrome on my hd, are there spare parts

Hey there
A friend of mine dented his chrome bezel on his touch hd, is there any manual that shows how to replace it, and from where can we purchase it
Thanks

try this
i donno if the site is secure
http://mobile.brando.com.hk/prod_detail.php?prod_id=03867

Slightly off topic, but in case your friend ever does replace the bezel or even the whole back cover, please post a photo of what the back cover looks like without the bezel. I am interested to see how the cover will look without the bezel (does the camera protrude through the cover, does the camera fit exactly inside the square opening in the cover, etc.)
I wouldn't mind having an HD without it's bezel, but I don't want to experiment with removing mine just yet. Your friend seems to be in a good position to possibly do just that.
Just a random thought. Thanks in advance if you can help.
Good luck with the search.

You may want to google for the "blackstone service manual" too, it shows how to correctly disassemble/reassamble the device.

taking off top plastic bezel

hello,
has anybody tried taking off the plastic housing/bezel? Im trying to get a better look at the lcd panel/digitizer...
if you have successfully taken it apart, please let me know how you did it...thanks in advance.
it looks like its probably just held on by internal plastic clips that I can pop off but not sure.

I've run a guitar pick (medium-light) down the right edge of the Slide and the bezel opened up. I wasn't brave enough to take it any further. As you can probably tell the digitizer and LCD come up with the bezel. Not knowing where the ribbon/cable is located kept me from proceeding any further. In theory one should be able to free all the "teeth" around the whole of the bezel and deduce the location of the ribbon/cable. A schematic would be preferable.

[GUIDE] Xperia Arc Disassembly

EDIT
"meyourchum" has provded a link to get offical disassembly instruction with lot more information.
Check it for yourself
Hello folks,
I had a chance to work on my friends arc who bought a Rogers version and dropped it. He had it totally mess on the case and needed the full housing replacement.
I hope that doesn't happen to anyone. I didn't take any photos but I am trying to explain everything as it was to help anyone with this.
General Note:
- Anywhere you got stuck, watch some X10 Disassembly video
- Be very gentle to your phone in this process
- Besides all the screws the rest of the phone is put together with glue(Sticky Back) and snap(plastic for main board)
- Using this information on your own risk as I don't take any responsibility if anything happens to your phone.
Instruction
1) Remove the back battery cover. Thats the easiest part
2) Need star shaped screw driver[Trox](I bought the set for $5) there are 4 screws like that and two which opens with phillips screwdriver(tiny) This is what I bought
All the above we all have seen them
3) After removing the 6 screws remove the front fascia of the phone with a guitar picks, something skinny but sturdy*
* I recommend not using anything other than rubber or plastic in the whole process.
4) Main board is snapped in with plastic to the body which easily can be opened.
5) Little board on the bottom is glued(sticky back @ top) which you can remove with pulling little hard but make sure you don't break it.
6) Majority of the wire you see connected to mainboard can be discounted (snap in wires)
7) Removing the screen: from outside of the phone (like you are looking directly to screen like you normally do) you need to put something under neat and raise up the screen. This part has glue as well and its hard to lift but I did it and it should be possible.
8) if you are doing a full housing replacement, then there are stuff here and there that you need to remove and re-use it on the new housing(Like 3.5 mm jack, HDMI lid, etc.)
Good Luck and let me know if you have any questions.

1st time... ehm.. taking the Arc apart, that is!
Helluw there
Just read your post, and thought I wanted to share with you, that I might be opening one of these slick little things. My friend broke his display, and the ISP is talking about some 'off the scale' repair prizes.
...So, he asked me to do the job
Told him I didn't have any experience on the disassembling of this phonetype, but he trusts me it seems
I might return with some questions in case of problems, is that OK with you Nimche?
Greetingz

Hope u have the courage to make a video next time
Sent from my Arc using XDA premium App

xelion said:
Helluw there
Just read your post, and thought I wanted to share with you, that I might be opening one of these slick little things. My friend broke his display, and the ISP is talking about some 'off the scale' repair prizes.
...So, he asked me to do the job
Told him I didn't have any experience on the disassembling of this phonetype, but he trusts me it seems
I might return with some questions in case of problems, is that OK with you Nimche?
Greetingz
Click to expand...
Click to collapse
Sure, no problem. I would be more than happy to answer. Lets see just some general stuff...
Note: anywhere you got stuck, watch some X10 Disassembly video
Note: be very gentle to your phone in this process
- you remove the back battery cover. Thats the easiest part
- you need that star shaped screw driver(I bought the set for $5) there are 4 screws like that and two which opens with phillips screwdriver(tiny)
All the above we all have seen them
after removing the 6 screws
note: besides all the screws the rest of the phone is put together with glue and snap(plastic for main board)
- remove the front fascia of the phone with a guitar picks, something skinny but sturdy*
* I recommend not using anything other than rubber or plastic in the whole process.
- main board is snapped in with plastic to the body which easily can be opened. I change full housing and not sure if you have to remove the hard key button from the bottom end of the phone too or not but that little board on the bottom is glue which you can remove with pulling little hard but make sure you don't break it.
- All the wire you see connected to mainboard can be discounted (snap in wires)
- There is a big one which goes to the screen you have to dis-attach that before removing the screen
- Removing the screen: from outside of the phone (like you are looking directly to screen like you normally do) you need to put something under neat and raise up the screen. This part has glue as well and its hard to lift but I did it and it should be possible.
Good Luck and let me know if you have any questions.

Can you answer this??? It get's hot here (and also in the same spot on the front.. so what's inside at this point??

CPU is right behind the second cover. I wish I could take some photos.

Nimche said:
CPU is right behind the second cover. I wish I could take some photos.
Click to expand...
Click to collapse
Thanks for the clarification. I was also suspecting since this area gets damn hot when playing games and even at charging (sometimes).
So seems like they move the CPU from behind the battery in X10 to near to the camera in Arc .

Can I change only the front faceplate around the screen without removing the mainboard? How easy would that be? I want to change mine to Misty Silver as Rogers only carry the Midnight Blue.
Also, for glued parts, do I have to glue them back on the new housing?

hellocng said:
Can I change only the front faceplate around the screen without removing the mainboard? How easy would that be? I want to change mine to Misty Silver as Rogers only carry the Midnight Blue.
Also, for glued parts, do I have to glue them back on the new housing?
Click to expand...
Click to collapse
Glue part, they are more sticky than glued. You just simply stick it back where it was.
Where is the silver face you found?
This is retarded from them...
Digitizer and screen(one part) are sticked to the front face. In order to for your to change the faceplate only(front) you may have to go through the whole process because the wires from digitizer are going through a big hole to the main board. You don't want to mess around with $700 or $800.
Inside, everything is small. really small. I thought I totally screwed up the whole thing. Technology has gone forward alot since I was a kid putting radio together.
Good Luck

prathaban said:
Thanks for the clarification. I was also suspecting since this area gets damn hot when playing games and even at charging (sometimes).
So seems like they move the CPU from behind the battery in X10 to near to the camera in Arc .
Click to expand...
Click to collapse
Yes, there are two board one above battery and one below batter @ bottom of the phone
On top is the main board
on bottom is the board for hard keys.
Nicely put together but they could have done a better job there....

Are there three parts to the housing? I assume there is the front plate, middle housing with the chrome, and the battery cover. The mainboard should be in the middle with the chrome. So I can't just detach the screen front the front plate? What is holding the three pieces of housing together? The six screws?
There are silver housings on eBay from time to time. Though, blue is a lot more common.

Three pieces. Back battery cover which is nothing.
Then there are two main pieces.
Chrome which is more like a holder of the fascia.
If I remember correctly, the front Fascia is the one holding all the board on it including that metal look piece(aluminum probably)
I will take photos and upload here...

Uploaded photos to the first post...

Hey, I'm looking to replace the chrome piece which has a few nasty chips in it, after removing the second back cover, how easy is it to take off that chrome piece?

Great post

How can I replace digitizer? I dropped my phone and the glass cracked

anyone know where i can get the tiny screw driver? I cant seem to find the correct one. they are either too small or too big.

how easy is it to replace the front cover, ive cracked the top of it and chipped a bit out the side (surrounding the screen) i presume it'd be simple enough. And does anyone know where i can get a good quality/genuine front cover replacement?

soldiers33 said:
anyone know where i can get the tiny screw driver? I cant seem to find the correct one. they are either too small or too big.
Click to expand...
Click to collapse
Sorry, you could have sent a private message.
I bought the screw driver here at local tool shop. Home Depot sells them.
Its called Trox Screw Driver and I bought exactly this one http://www.homedepot.com/webapp/wcs/stores/servlet/ProductDisplay?storeId=10051&productId=100087664&langId=-1&catalogId=10053&ci_sku=100087664&ci_kw={keyword}&cm_mmc=shopping-_-googleads-_-pla-_-100087664&ci_gpa=pla&locStoreNum=618
I don't have the packaging but they should be standard.
Good Luck

mps83 said:
how easy is it to replace the front cover, ive cracked the top of it and chipped a bit out the side (surrounding the screen) i presume it'd be simple enough. And does anyone know where i can get a good quality/genuine front cover replacement?
Click to expand...
Click to collapse
You can find the whole housing between $30 to $40 but the front cover is that actual main piece that holds all the internal components + the screen.
If the crack doesn't bug you much, I would not do it since you have to replace the sticker behind you battery as well, which is not easy to peel off + you have to take the screen off the old front fascia which is glued and kind of hard to take off.
Downside of the whole thing for me was the sticker. I have to find an alternative for this problem.

Repair HD2, now trouble assembling?

I recently tried repairing a friends HD2, because he had a smashed screen.
I bought the new screen and some 2mm double sided tape. Took the phone apart, and managed to see the lcd was damaged also. Bought one of those then taped the new screen and lcd together using the tape.
The inner chassis had all the old tape on it still, so I bought a new inner chassis. Waited for it, then stuck the new lcd / digitizer to it. The button end didnt seem to stick down that well - even with the new chassis, with the buttons wanting to drop out, and them not sitting out of the screen like they should.
I thought it must be due to the phone only partially assembled, so went ahead and installed the rest of the phone.
Now its together the button end of the phone wont sit in the shell properly and the buttons seem to be lower than they should...
How am i supposed to get this inner chassis to stick properly, and are there any tips or vids to show how its supposed to sit?
thanks.

maybe this video can help you with assembling your phone.
Search on youtube for t8Q7mXdcJ54.

Ive watched that video numerous times, and its a little misleading as to how much is required. Extra tape in places that had to be cut and removed, labels not sticking back down like they do in the video etc.
Im after information as to how people stuck the lcd/digitizer to the inner chassis. I used a new inner chassis with tape pre applied, and it still didnt seem to stick the two things together enough. When you stick the chassis (with lcd/digitizer) into the outer case, it doesnt sit into the case enough, and the buttons are not sitting right.

If u have purchased lcd with digitizer,u could look for flat cable that connects from lcd to mbo,maybe u need to form it.buttons have points to allign,but u need to center both sides in micrometer to function normal.lcd/digitizer frame must have black tape on edges.
Sent from my Milestone using Tapatalk

kew1701 said:
If u have purchased lcd with digitizer,u could look for flat cable that connects from lcd to mbo,maybe u need to form it.
Click to expand...
Click to collapse
Please explain? Not sure what u mean by "form it"
buttons have points to allign,but u need to center both sides in micrometer to function normal.lcd/digitizer frame must have black tape on edges.
Click to expand...
Click to collapse
done this and still no luck

I have the same problem like foney!
See this:
argh, i can't post my photos! how to do it now, i don't have 8 posts yet!
I've used "3M 300LSE" as a profesional doublesided tape i thought and also put a 2mm stripe below the keyboard, but the display is not really fixed onto the chassi around the keyboard and the keys also can't be used really, because they are maybe not correct centered onto the keyboard circuit board. i've been using the assembly video from htc, but there it's not mentionend very well, how to do it right.

foney said:
Please explain? Not sure what u mean by "form it"
Maybe it need curved angle to 100% fit
done this and still no luck
Click to expand...
Click to collapse
Hmm,last thing i can think is that lcd/digitizer is not properly glued/taped.Did u put pressure for few hours on lcd/digitizer and middle frame?

it is taped on around the lcd using 2mm 3M double sided tape. The chassis i bought new, with tape included. When you stick the lcd/digi to the chassis, it appears that the button end, as l0rdius mentioned, isnt stuck down enough.
The video has the guy "magically" sticking it all together and all going together as it should, but doesnt show any real detail, like showing how things go together to fit properly.
edit/ pulled the phone apart again, and its definitely a case of the tape on the chassis near the buttons not sticking correctly. Ive wrapped it in rubber bands, and used some wooden clothes pegs to try to secure the two better. If it doesnt stick, then I may have to use something stronger than tape, like Tarzans Grip

I've found another thread, in which "profahmad" posted some hints:
http://forum.xda-developers.com/showthread.php?t=640328&page=8
Today i've ordered some more 3M 300LSE and want to take a new try on weekend with these hints. Hope i get the display better glued to the chassis and the buttons correctly justified.
Whats about the sticker under the battery. do you guys have problems reassembling it again and again? Or how do you handle it?

l0rdius said:
I've found another thread, in which "profahmad" posted some hints:
http://forum.xda-developers.com/showthread.php?t=640328&page=8
Whats about the sticker under the battery. do you guys have problems reassembling it again and again? Or how do you handle it?
Click to expand...
Click to collapse
Im using glue like in the link if applying pressure for a day or two doesnt work.
I applied a little double sided tape under it, then when i left the phone for a few days with the battery in it seemed to stick down fairly well. Not like factory new, but good enough.